Professional Documents
Culture Documents
Srs Nissan
Srs Nissan
E
CONTENTS
BASIC INSPECTION .................................... 5 Diagnosis Procedure (Component diagnosis) .......22 F
DIAGNOSIS AND REPAIR WORK FLOW ......... 5 B1011, B1012, B1013, B1014, B1015 DIAG-
Work Flow ................................................................. 5 NOSIS SENSOR UNIT ...................................... 23 G
Description ...............................................................23
FUNCTION DIAGNOSIS ............................... 7 DTC Logic ................................................................23
Diagnosis Procedure (Component diagnosis) .......24
SRS AIR BAG SYSTEM ...................................... 7 SRC
System Diagram ........................................................ 7 B1017, B1020, B1021 OCCUPANT SENS C/U
System Description ................................................... 7 ... 25
Component Parts Location ........................................ 8 Description ...............................................................25 I
Component Description ............................................. 9 DTC Logic ................................................................25
Diagnosis Procedure (Component diagnosis) .......26
OCCUPANT CLASSIFICATION SYSTEM .........10
System Diagram ...................................................... 10 B1018 OCCUPANT SENS ................................ 27 J
System Description ................................................. 10 Description ...............................................................27
Component Parts Location ...................................... 10 DTC Logic ................................................................27
Component Description ........................................... 11 Diagnosis Procedure (Component diagnosis) .......28 K
PASSENGER SEAT BELT WARNING SYS- B1022 OCCUPANT SENS C/U ......................... 29
TEM ....................................................................12 Description ...............................................................29
System Diagram ...................................................... 12 L
DTC Logic ................................................................29
System Description ................................................. 12 Diagnosis Procedure (Component diagnosis) .......30
Component Parts Location ...................................... 13
Component Description ........................................... 13 B1023 PASS A/B INDCTR CKT ....................... 31 M
Description ...............................................................31
DIAGNOSIS SYSTEM (AIRBAG) ......................15 DTC Logic ................................................................31
Diagnosis Description ............................................. 15 Diagnosis Procedure (Component diagnosis) .......32
N
CONSULT-III Function ............................................ 17
B1026, B1027, B1028, B1029, B1030, B1031
COMPONENT DIAGNOSIS ......................... 19 DIAGNOSIS SENSOR UNIT ............................. 33
Description ...............................................................33 O
B1001, B1002, B1003, B1004, B1005 DIAG- DTC Logic ................................................................33
NOSIS SENSOR UNIT .......................................19 Diagnosis Procedure (Component diagnosis) .......34
Description .............................................................. 19
P
DTC Logic ............................................................... 19 B1033, B1034 CRASH ZONE SEN .................. 35
Diagnosis Procedure (Component diagnosis) ...... 20 Description ...............................................................35
DTC Logic ................................................................35
B1006, B1007, B1008, B1009, B1010 DIAG- Diagnosis Procedure (Component diagnosis) .......36
NOSIS SENSOR UNIT .......................................21
Description .............................................................. 21 B1035, B1036, B1038, B1040 CRASH ZONE
DTC Logic ............................................................... 21 SEN ................................................................... 37
B1049, B1054 DRIVER AIRBAG MODULE ...... 41 B1083 PRE-TEN FRONT RH ............................ 69
Description .............................................................. 41 Description .............................................................. 69
DTC Logic ............................................................... 41 DTC Logic ............................................................... 69
Diagnosis Procedure (Component diagnosis) ...... 42 Diagnosis Procedure (Component diagnosis) ...... 70
B1050, B1055 DRIVER AIRBAG MODULE ...... 44 B1084 PRE-TEN FRONT RH ............................ 71
Description .............................................................. 44 Description .............................................................. 71
DTC Logic ............................................................... 44 DTC Logic ............................................................... 71
Diagnosis Procedure (Component diagnosis) ...... 45 Diagnosis Procedure (Component diagnosis) ...... 72
B1051, B1056 DRIVER AIRBAG MODULE ...... 47 B1086 PRE-TEN FRONT LH ............................. 73
Description .............................................................. 47 Description .............................................................. 73
DTC Logic ............................................................... 47 DTC Logic ............................................................... 73
Diagnosis Procedure (Component diagnosis) ...... 48 Diagnosis Procedure (Component diagnosis) ...... 74
B1052, B1057 DRIVER AIRBAG MODULE ...... 50 B1087 PRE-TEN FRONT LH ............................. 75
Description .............................................................. 50 Description .............................................................. 75
DTC Logic ............................................................... 50 DTC Logic ............................................................... 75
Diagnosis Procedure (Component diagnosis) ...... 51 Diagnosis Procedure (Component diagnosis) ...... 76
B1058, B1059, B1060, B1061, B1062, B1063 B1088 PRE-TEN FRONT LH ............................. 77
DIAGNOSIS SENSOR UNIT .............................. 53 Description .............................................................. 77
Description .............................................................. 53 DTC Logic ............................................................... 77
DTC Logic ............................................................... 53 Diagnosis Procedure (Component diagnosis) ...... 78
Diagnosis Procedure (Component diagnosis) ...... 54
B1089 PRE-TEN FRONT LH ............................. 79
B1065, B1070 ASSIST A/B MODULE .............. 55 Description .............................................................. 79
Description .............................................................. 55 DTC Logic ............................................................... 79
DTC Logic ............................................................... 55 Diagnosis Procedure (Component diagnosis) ...... 80
Diagnosis Procedure (Component diagnosis) ...... 56
B1106, B1107, B1108, B1109, B1110, B1111
B1066, B1071 ASSIST A/B MODULE .............. 57 DIAGNOSIS SENSOR UNIT ............................. 81
Description .............................................................. 57 Description .............................................................. 81
DTC Logic ............................................................... 57 DTC Logic ............................................................... 81
Diagnosis Procedure (Component diagnosis) ...... 58 Diagnosis Procedure (Component diagnosis) ...... 82
B1067, B1072 ASSIST A/B MODULE .............. 59 B1113, B1114 SATELLITE SENS RH .............. 83
Description .............................................................. 59 Description .............................................................. 83
DTC Logic ............................................................... 59 DTC Logic ............................................................... 83
Diagnosis Procedure (Component diagnosis) ...... 60 Diagnosis Procedure (Component diagnosis) ...... 84
B1068, B1073 ASSIST A/B MODULE .............. 61 B1115, B1116 SATELLITE SENS RH .............. 85
Description .............................................................. 61 Description .............................................................. 85
DTC Logic ............................................................... 61 DTC Logic ............................................................... 85
Diagnosis Procedure (Component diagnosis) ...... 62 Diagnosis Procedure (Component diagnosis) ...... 86
B1074, B1075, B1076, B1077, B1078, B1079 B1118, B1119 SATELLITE SENS LH ............... 87
DIAGNOSIS SENSOR UNIT .............................. 63 Description .............................................................. 87
Description .............................................................. 63 DTC Logic ............................................................... 87
DTC Logic ............................................................... 63 Diagnosis Procedure (Component diagnosis) ...... 88
Diagnosis Procedure (Component diagnosis) ...... 64
B1120, B1121 SATELLITE SENS LH ............... 89
B1122, B1123, B1124, B1125, B1126, B1127 B1147 CURTAIN MODULE RH ...................... 115
B
DIAGNOSIS SENSOR UNIT ..............................91 Description ............................................................. 115
Description .............................................................. 91 DTC Logic .............................................................. 115
DTC Logic ............................................................... 91 Diagnosis Procedure (Component diagnosis) ..... 116
Diagnosis Procedure (Component diagnosis) ...... 92 C
B1148 CURTAIN MODULE RH ...................... 117
B1129 SIDE MODULE RH .................................93 Description ............................................................. 117
Description .............................................................. 93 DTC Logic .............................................................. 117
D
DTC Logic ............................................................... 93 Diagnosis Procedure (Component diagnosis) ..... 118
Diagnosis Procedure (Component diagnosis) ...... 94
B1150 CURTAIN MODULE LH ....................... 119
B1130 SIDE MODULE RH .................................95 Description ............................................................. 119 E
Description .............................................................. 95 DTC Logic .............................................................. 119
DTC Logic ............................................................... 95 Diagnosis Procedure (Component diagnosis) ..... 120
Diagnosis Procedure (Component diagnosis) ...... 96 F
B1151 CURTAIN MODULE LH ....................... 121
B1131 SIDE MODULE RH .................................97 Description ............................................................. 121
Description .............................................................. 97 DTC Logic .............................................................. 121
DTC Logic ............................................................... 97 Diagnosis Procedure (Component diagnosis) ..... 122 G
Diagnosis Procedure (Component diagnosis) ...... 98
B1152 CURTAIN MODULE LH ....................... 123
B1132 SIDE MODULE RH .................................99 Description ............................................................. 123
SRC
Description .............................................................. 99 DTC Logic .............................................................. 123
DTC Logic ............................................................... 99 Diagnosis Procedure (Component diagnosis) ..... 124
Diagnosis Procedure (Component diagnosis) .... 100
B1153 CURTAIN MODULE LH ....................... 125 I
B1134 SIDE MODULE LH ................................ 101 Description ............................................................. 125
Description ............................................................ 101 DTC Logic .............................................................. 125
DTC Logic ............................................................. 101 Diagnosis Procedure (Component diagnosis) ..... 126 J
Diagnosis Procedure (Component diagnosis) .... 102
B1202, B1203, B1204, B1205, B1206, B1207
B1135 SIDE MODULE LH ................................ 103 DIAGNOSIS SENSOR UNIT ........................... 127
Description ............................................................ 103 Description ............................................................. 127 K
DTC Logic ............................................................. 103 DTC Logic .............................................................. 127
Diagnosis Procedure (Component diagnosis) .... 104 Diagnosis Procedure (Component diagnosis) ..... 128
L
B1136 SIDE MODULE LH ................................ 105 B1209 FRONTAL COLLISION DETECTION .. 129
Description ............................................................ 105 Description ............................................................. 129
DTC Logic ............................................................. 105 DTC Logic .............................................................. 129
Diagnosis Procedure (Component diagnosis) .... 106 Diagnosis Procedure (Component diagnosis) ..... 129 M
B1137 SIDE MODULE LH ................................ 107 B1210 SIDE COLLISION DETECTION .......... 131
Description ............................................................ 107 Description ............................................................. 131 N
DTC Logic ............................................................. 107 DTC Logic .............................................................. 131
Diagnosis Procedure (Component diagnosis) .... 108 Diagnosis Procedure (Component diagnosis) ..... 131
B1138, B1139, B1140, B1141, B1142, B1143 ECU DIAGNOSIS ....................................... 133 O
DIAGNOSIS SENSOR UNIT ............................ 109
Description ............................................................ 109 DIAGNOSIS SENSOR UNIT ........................... 133
DTC Logic ............................................................. 109 DTC Index ............................................................. 133 P
Diagnosis Procedure (Component diagnosis) .... 110 Wiring Diagram - SRS AIR BAG CONTROL SYS-
TEM - ..................................................................... 141
B1145 CURTAIN MODULE RH ....................... 111
Description ............................................................ 111 SYMPTOM DIAGNOSIS ............................ 147
DTC Logic ............................................................. 111
Diagnosis Procedure (Component diagnosis) .... 112
SRS AIR BAG WARNING LAMP DOES NOT
TURN OFF ....................................................... 147
B1146 CURTAIN MODULE RH ....................... 113 Diagnosis Procedure ............................................. 147
OVERALL SEQUENCE
C
SRC
M
JMHIA0027GB
DETAILED FLOW
1.GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom.
>> GO TO 2.
2.PERFORM PRELIMINARY CHECK
At the beginning of inspection, confirm the condition of power supply circuit, check that the battery is charged
and fuses and fusible links are not blown.
Is the inspection result normal?
YES >> GO TO 3 or GO TO 4.
NO >> Repair or replace the battery and fuse/fusible links.
3.PERFORM SELF-DIAGNOSIS USING CONSULT-III (WITH CONSULT-III)
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES >> GO TO 5.
NO >> Repeat DTC confirmation with diagnostic procedure.
4.PERFORM SELF-DIAGNOSIS AIR BAG WARNING LAMP (WITHOUT CONSULT-LLL)
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES >> GO TO 5.
NO >> Repeat DTC confirmation with diagnostic procedure.
5.REPAIR OR REPLACE
Repair or replace the malfunctioning part.
After the malfunction is repaired, erase the self-diagnostic result. Refer to SRC-15, "Diagnosis Description".
>> GO TO 6.
6.FINAL CHECK
Check the screen of CONSULT-III and /or Air bag warning lamp status.
Are all malfunctions corrected?
YES >> INSPECTION END.
NO >> GO TO 3 or GO TO 4.
SRC
JMHIA0370GB
P
System Description INFOID:0000000001694472
JMHIA0424ZZ
1. Front passenger air bag module 2. Driver air bag module 3. Spiral cable
Passenger air bag off indicator
4. 5. Diagnosis sensor unit (ACU) 6. Satellite sensor (LH/RH)
(Cut-off telltale)
Front seat belt pre-tensioner (LH/
7. 8. Seat belt buckle switch (LH/RH) 9. Front side air bag module (LH/RH)
RH)
10. Curtain air bag module 11. Crash zone sensor 12. OCS seat sensor mat
13. OCS control unit
SRC
JMHIA0371GB
• Air bag sensor are prepared for operation while the ignition switch is in the ON or START position.
• The operation of supplemental restraint system is different from collision modes applicaitions. For example,
the driver air bag module and front passenger air bag module are activated in a frontal collision but not in a I
side collision.
• SRS configurations which are activated for some collision modes are as follows.
J
SRS configuration Frontal collision Left side collision Right side collision
Driver air bag module. Refer to SRC-129 × — —
Front passenger air bag module. Refer to SRC-129 × — — K
Front LH seat belt pre-tensioner. Refer to SRC-129 × — —
Front RH seat belt pre-tensioner. Refer to SRC-129 × — —
L
Front LH side air bag module. Refer to SRC-131 — × —
Front RH side air bag module. Refer to SRC-131 — — ×
LH side curtain air bag module. Refer to SRC-131 — × — M
RH side curtain air bag module. Refer to SRC-131 — — ×
×: Application, —: Not application
N
JMHIA0023GB
NOTE:
Operation of ACU when ACU receives information from Occupant Classification System (OCS)
Status (Front passenger Passenger Air bag Passenger Air bag off Air bag warning lamp Seat belt warning lamp
seat) indicator (Cut-off tell- (when front passenger
tale) seat is unbuckled)
Empty Suppress Off Off Off
Child/ child-seat Suppress On Off On
Adult Enable to deploy Off Off On
Trouble Suppress On Blinking Off
JMHIA0001ZZ
G
JMHIA0024GB
JMHIA0025GB
This Passenger Seat Belt Warning System has the following function.
1. Turns ON seat belt warning lamp (1), when the OCS judges
adult or child in the passenger seat and the passenger seat belt
buckle switch is not on.
NOTE:
In addition, a seat belt warning lamp illuminates and a seat belt
alarm sounds, when the driver seat belt buckle switch is not on,
This does not relate to the air bag sensor. (Refer to BCM.)
JMHIA0003ZZ
NOTE:
Operation of ACU when ACU receives information from Occupant Classification System (OCS)
Status (Front passenger Passenger Air bag Passenger air bag off Air bag warning lamp Seat belt warning lamp
seat) indicator (cut-off telltale) (When front passenger
seat is unbuckled)
Empty Suppress Off Off Off
Child/ child-seat Suppress On Off On
Adult Enable to deploy Off Off On
Trouble Suppress On Blinking Off
A
SRS AIR BAG
SRC
JMHIA0424ZZ J
1. Front passenger air bag module 2. Driver air bag module 3. Spiral cable
Passenger air bag off indicator
4.
(Cut-off telltale)
5. Diagnosis sensor unit (ACU) 6. Satellite sensor (LH/RH) K
Front seat belt pre-tensioner (LH/
7. 8. Seat belt buckle switch (LH/RH) 9. Front side air bag module (LH/RH)
RH)
10. Curtain air bag module 11. Crash zone sensor 12. OCS seat sensor mat L
13. OCS control unit
JMHIA0026GB
JMHIA0003ZZ
CAUTION: B
• Do not use electrical test equipment on any circuit related to the SRS unless instructed in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
• Do not repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a C
new one.
• Keep ground portion clean.
D
DIAGNOSIS FUNCTION
• The SRS self-diagnosis results can be read by using “AIR BAG” warning lamp and/or CONSULT-III.
• The user mode is exclusively prepared for the customer (driver). This mode warns the driver of a system E
malfunction through the operation of the “AIR BAG” warning lamp.
• The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
• The mode applications for the “AIR BAG” warning lamp and CONSULT-III are as follows.
F
User mode Diagnosis mode Display type
“AIR BAG” warning lamp X X ON-OFF operation
G
CONSULT-III – X Monitoring
HOW TO PERFORM TROUBLE DIAGNOSIS FOR QUICK AND ACCURATE REPAIR SRC
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
I
Information from Customer.
• WHAT..... Vehicle model.
• WHEN..... Date, Frequencies. J
• WHERE..... Road conditions.
• HOW..... Operating conditions, Symptoms.
Preliminary Check. K
Check that the following parts are in good order.
• Battery (Refer to PG-3, "How to Handle Battery").
• Fuse (Refer to SRC-141, "Wiring Diagram - SRS AIR BAG CONTROL SYSTEM -").
• System component-to-harness connections. L
BF-1845D
• No malfunction is detected.
—
• No further action is necessary.
SHIA0011E
SHIA0012E
SHIA0014E
SRC
DIAGNOSTIC PROCEDURE (With CONSULT-III)
PHIA0709E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat- F
tery damage in collision.
INSTALLATION G
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
DTC Logic INFOID:0000000001694486 SRC
DTC No. Trouble diagnosis name DTC detecting condition Possible cause J
B1001 CONTROL UNIT Diagnosis sensor unit is out of order. Internal breakdown in diagnosis sensor
B1002 unit (ACU).
B1003 K
B1004
B1005
L
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
Turn ignition switch ON. M
>> GO TO 2.
N
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected? O
YES >> Refer to SRC-20, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
P
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694487
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
OPERATION
It detects a shock that exceeds specified level and watches such systems as the driver and passenger air bag, D
side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate prop-
erly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694489
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
OPERATION
It detects a shock that exceeds specified level and watches such systems as the driver and passenger air bag, D
side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate prop-
erly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694492
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
OPERATION D
This unit classifies occupant in passenger seat and detects electrical malfunctions in Occupant Classification
System, and transmits malfunction information to air bag control unit.
E
STRUCTURE
It is integrated into the seat sensor mat and detects the occupants with Occupant Classification System (OCS)
control unit that classifies the occupants.
F
INSTALLATION
Occupant Classification System (OCS) control unit is installed in the passenger seat cushion.
G
DTC Logic INFOID:0000000001694495
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694496
With CONSULTlll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
1. Replace OCS CONTROL UNIT. (passenger side seat cushion assembly.)
2. Check the screen of CONSULT-lll.
is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
OPERATION D
The unit classifies occupant in passenger seat and transmits it to Occupant Classification System (OCS) con-
trol unit.
E
STRUCTURE
Plural sensors are installed in the sensor mat to prevent incorrect sensing induced by the sitting position.
F
INSTALLATION
Seat sensor mat is installed in the passenger seat cushion.
DTC Logic INFOID:0000000001694498 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-III. N
Is malfunctioning part detected?
YES >> Refer to SRC-28, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK OCCUPANT CLASSIFICATION SYSTEM SENSOR
1. Replace OCS SENSOR. (passenger side seat cushion assembly.)
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
OPERATION D
This unit classfies occupant in passenger seat and detects electrical malfunction in Occupant Classification
System (OCS) and transmits malfunction information to air bag control unit.
E
STRUCTURE
It is integrated into the seat sensor mat and detects the occupants and Occupant Classification System (OCS)
control unit that classifies the occupants.
F
INSTALLATION
Occupant Classification System (OCS) control unit is installed in the passenger seat cushion.
G
DTC Logic INFOID:0000000001694501
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694502
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
1. Replace OCS CONTROL UNIT. (passenger side seat cushion assembly.)
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE
Passenger air bag indicator (cut-off telltale) with LED illumination.
F
INSTALLATION
Passenger air bag indicator (cut-off telltale) is installed at the instrument panel center.
G
DTC Logic INFOID:0000000001694504
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694505
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK PASSENGER AIR BAG OFF INDICATOR
1. Replace passenger air bag off indicator.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air D
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) to
ensure proper operation.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694507
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694508
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Integrated type of the “G” sensor element for frontal collision with output terminals for signal voltage.
INSTALLATION F
Crash zone sensor is installed on the radiator core support assembly with fixed nuts.
DTC Logic INFOID:0000000001694510
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1033 CRASH ZONE SEN- Crash zone sensor is out of order. • Disconnection of wiring harness.
B1034 SOR • Internal breakdown in crash zone
[UNIT FAIL] sensor.
• Internal breakdown in diagnosis sen- J
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT M
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK CRASH ZONE SENSOR
1. Replace crash zone sensor.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1035, B1036, B1038, B1040 [COMM FAIL] CRASH ZONE SENSOR B
Main “G” sensor that generates signal voltage, when it detects deceleration beyond the specified level caused
by vehicle frontal collision.
C
OPERATION
When ACU defines both signal voltage of the “G” sensor and the safing sensor to be that of collision which
exceeds specified level, the driving circuit switches on and feeds the electric ignitor of both driver and passen- D
ger air bags and pre-tensioner seat belt.
STRUCTURE E
Integrated type of the “G” sensor element for frontal collision with output terminals for signal voltage.
INSTALLATION F
Crash zone sensor is installed on the radiator core support assembly with fixed nuts.
DTC Logic INFOID:0000000001694513
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1035 CRASH ZONE SEN- Crash zone sensor is out of order. • Disconnection of wiring harness and
SOR open/short.
[COMM FAIL] • Internal breakdown in crash zone
B1036 [UNMATCH] sensor. J
B1038 [OPEN/UPR-VB- • Internal breakdown in diagnosis sen-
SHORT] sor unit (ACU).
B1040 [SHORT/UPR-GND-
SHORT] K
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694514
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK CRASH ZONE SENSOR
1. Replace crash zone sensor.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air D
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly.
E
STRUCTURE
It contains the “G” sensors for both for frontal and side collisions and spare battery function in case of main
battery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694516
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694517
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Driver air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Driver air bag module is installed on the center of steering wheel with fixed bolts.
DTC Logic INFOID:0000000001694519
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1049 DRIVER AIRBAG MOD- Driver air bag module circuit is open. • Disconnection of wiring harness and
B1054 ULE (including the spiral cable.) open.
[OPEN] • Internal breakdown in driver air bag
module. J
• Internal breakdown in spiral cable.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-42, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DRIVER AIR BAG MODULE
1. Replace driver air bag module.
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> GO TO 4.
4.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver side air bag module harness connector and body side harness connector.
3. Check continuity between driver side air bag module harness connector and body side harness connec-
tor.
SRC
OPERATION
In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Driver air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Driver air bag module is installed on the center of steering wheel with fixed bolts.
DTC Logic INFOID:0000000001694522
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1050 DRIVER AIRBAG MOD- Driver air bag module circuit is shorted • Disconnection of wiring harness and
B1055 ULE to some power supply circuit. short.
[VB-SHORT] (including the spiral cable.) • Internal breakdown in driver air bag
module.
• Internal breakdown in spiral cable.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES >> Refer to SRC-45, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
With CONSULT-lll
WARNING: D
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device. E
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR F
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2. G
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS SRC
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3. I
NO >> Repair or replace wiring harness.
3.CHECK DRIVER AIR BAG MODULE
1. Replace driver air bag module. J
2. Check the screen of CONSULT-III.
Is the inspection result normal?
K
YES >> INSPECTION END.
NO >> GO TO 4.
4.CHECK SPIRAL CABLE CIRCUIT L
1. Turn ignition switch OFF.
2. Disconnect driver side air bag module harness connector and body side harness connector.
3. Check continuity between driver side air bag module harness connector and body side harness connec- M
tor.
STRUCTURE E
Driver air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Driver air bag module is installed on the center of steering wheel with fixed bolts.
DTC Logic INFOID:0000000001694525
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1051 DRIVER AIRBAG MOD- Driver air bag module circuit is shorted • Disconnection of wiring harness and
B1056 ULE to ground. short.
[GND-SHORT] (including the spiral cable.) • Internal breakdown in driver air bag
module. J
• Internal breakdown in spiral cable.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-48, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DRIVER AIR BAG MODULE
1. Replace driver air bag module.
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> GO TO 4.
4.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver side air bag module harness connector and body side harness connector.
3. Check continuity between driver side air bag module harness connector and body side harness connec-
tor.
SRC
OPERATION
In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Driver air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Driver air bag module is installed on the center of steering wheel with fixed bolts.
DTC Logic INFOID:0000000001694528
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1052 DRIVER AIRBAG MOD- Driver air bag module circuit are shorted • Disconnection of wiring harness
B1057 ULE to each other. and short.
[SHORT] (including the spiral cable.) • Internal breakdown in driver air bag
module.
• Internal breakdown in spiral cable.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES >> Refer to SRC-51, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
With CONSULT-lll
WARNING: D
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device. E
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR F
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2. G
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS SRC
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3. I
NO >> Repair or replace wiring harness.
3.CHECK DRIVER AIR BAG MODULE
1. Replace driver air bag module. J
2. Check the screen of CONSULT-III.
Is the inspection result normal?
K
YES >> INSPECTION END.
NO >> GO TO 4.
4.CHECK SPIRAL CABLE CIRCUIT L
1. Turn ignition switch OFF.
2. Disconnect driver side air bag module harness connector and body side harness connector.
3. Check continuity between driver side air bag module harness connector and body side harness connec- M
tor.
DTC B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air D
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694531
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694532
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front passenger air bag module is installed on the instrument panel with fixed bolts.
DTC Logic INFOID:0000000001694534
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1065 ASSIST A/B MODULE Front passenger air bag module circuit • Disconnection of wiring harness and
B1070 [OPEN] is open. open.
• Internal breakdown in front passen-
ger air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-56, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT PASSENGER AIR BAG MODULE
1. Replace front passenger air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front passenger air bag module is installed on the instrument panel with fixed bolts.
DTC Logic INFOID:0000000001694537
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1066 ASSIST A/B MODULE Front passenger air bag module circuit • Disconnection of wiring harness and
B1071 [VB-SHORT] is shorted to some power supply circuit. short.
• Internal breakdown in front passen-
ger air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-58, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT PASSENGER AIR BAG MODULE
1. Replace front passenger air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front passenger air bag module is installed on the instrument panel with fixed bolts.
DTC Logic INFOID:0000000001694540
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1067 ASSIST A/B MODULE Front passenger air bag module circuit • Disconnection of wiring harness and
B1072 [GND-SHORT] is shorted to ground. short.
• Internal breakdown in front passen-
ger air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-60, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT PASSENGER AIR BAG MODULE
1. Replace front passenger air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front passenger air bag module is installed on the instrument panel with fixed bolts.
DTC Logic INFOID:0000000001694543
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1068 ASSIST A/B MODULE Front passenger air bag module circuits • Disconnection of wiring harness and
B1073 [SHORT] are shorted to each other. short.
• Internal breakdown in front passen-
ger air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-56, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT PASSENGER AIR BAG MODULE
1. Replace front passenger air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air D
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694546
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694547
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694549 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1081 PRE-TEN FRONT RH Front RH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[OPEN] is open. open.
• Internal breakdown in front RH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-66, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front RH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694552 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1082 PRE-TEN FRONT RH Front RH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[VB-SHORT] is shorted to some power supply circuit. short.
• Internal breakdown in front RH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-68, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front RH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694555 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1083 PRE-TEN FRONT RH Front RH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[GND-SHORT] is shorted to ground. short.
• Internal breakdown in front RH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-70, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front RH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694558 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1084 PRE-TEN FRONT RH Front RH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[SHORT] are shorted to each other. short.
• Internal breakdown in front RH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-72, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspectiion result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front RH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694561 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1086 PRE-TEN FRONT LH Front LH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[OPEN] is open. open.
• Internal breakdown in front LH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-74, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front LH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694564 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1087 PRE-TEN FRONT LH Front LH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[VB-SHORT] is shorted to some power supply circuit. short.
• Internal breakdown in front LH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-76, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front LH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694567 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1088 PRE-TEN FRONT LH Front LH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[GND-SHORT] is shorted to ground. short.
• Internal breakdown in front LH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-78, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front LH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.
F
INSTALLATION
Front LH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694570 G
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1089 PRE-TEN FRONT LH Front LH seat belt pre-tensioner circuit • Disconnection of wiring harness and
[SHORT] are shorted to each other. short.
• Internal breakdown in front LH seat J
belt pre-tensioner.
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. N
Is malfunctioning part detected?
YES >> Refer to SRC-80, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT SEAT BELT PRE-TENSIONER
1. Replace front LH seat belt pre-tensioner.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air D
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694573
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694574
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Integrated type of the G sensor element for side collision with output terminals for signal voltage.
INSTALLATION F
RH satellite sensor is installed at the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694576
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1113 SATELLITE SENS RH RH satellite sensor is out of order. • Disconnection of wiring harness.
B1114 [UNIT FAIL] • Internal breakdown in RH satellite
sensor.
• Internal breakdown in diagnosis sen- J
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT M
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SATELLITE SENSOR
1. Replace RH satellite sensor.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Integrated type of the G sensor element for side collision with output terminals for signal voltage.
INSTALLATION F
RH satellite sensor is installed at the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694579
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1115 SATELLITE SENS RH RH satellite sensor is out of order. • Disconnection of wiring harness.
[COMM FAIL] • Internal breakdown in RH satellite
B1116 [UNMATCH] sensor.
• Internal breakdown in diagnosis sen- J
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT M
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SATELLITE SENSOR
1. Replace RH satellite sensor.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Integrated type of the G sensor element for side collision with output terminals for signal voltage.
INSTALLATION F
LH satellite sensor is installed at the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694582
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1118 SATELLITE SENS LH LH satellite sensor is out of order. • Disconnection of wiring harness.
B1119 [UNIT FAIL] • Internal breakdown in LH satellite
sensor.
• Internal breakdown in diagnosis sen- J
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT M
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SATELLITE SENSOR
1. Replace LH satellite sensor.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Integrated type of the G sensor element for side collision with output terminals for signal voltage.
INSTALLATION F
LH satellite sensor is installed at the underside of center pillar with fixed nuts.
DTC Logic INFOID:0000000001694585
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1120 SATELLITE SENS LH LH satellite sens is out of order. • Disconnection of wiring harness.
[COMM FAIL] • Internal breakdown in LH satellite
B1121 [UNMATCH] sens.
• Internal breakdown in diagnosis sen- J
sor unit (ACU).
>> GO TO 2.
2.CHECK SELF-DIAG RESULT M
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SATELLITE SENSOR
1. Replace LH satellite sensor.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air D
bag, side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate
properly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694588
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694589
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front RH side air bag module is installed on the side of front seat back with fixed nuts.
DTC Logic INFOID:0000000001694591
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1129 SIDE MODULE RH Front RH side air bag module circuit is • Disconnection of wiring harness and
[OPEN] open. open.
• Internal breakdown in front RH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-94, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front RH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front RH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694594
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1130 SIDE MODULE RH Front RH side air bag module circuit is • Disconnection of wiring harness and
[VB-SHORT] shorted to some power supply circuit. short.
• Internal breakdown in front RH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-96, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front RH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front RH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694597
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1131 SIDE MODULE RH Front RH side air bag module circuit is • Disconnection of wiring harness and
[GND-SHORT] shorted to ground. short.
• Internal breakdown in front RH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-98, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front RH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front RH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694600
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1132 SIDE MODULE RH Front RH side air bag module circuit are • Disconnection of wiring harness and
[SHORT] shorted to each other. short.
• Internal breakdown in front RH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-100, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front RH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front LH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694603
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1134 SIDE MODULE LH Front LH side air bag module circuit is • Disconnection of wiring harness and
[OPEN] open. open.
• Internal breakdown in front LH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-102, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front LH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front LH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694606
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1135 SIDE MODULE LH Front LH side air bag module circuit is • Disconnection of wiring harness and
[VB-SHORT] shorted to some power supply circuit. short.
• Internal breakdown in front LH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-104, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front LH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front LH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694609
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1136 SIDE MODULE LH Front LH side air bag module circuit is • Disconnection of wiring harness and
[GND-SHORT] shorted to ground. short.
• Internal breakdown in front LH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-106, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front LH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
Front LH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
Front LH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic INFOID:0000000001694612
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1137 SIDE MODULE LH Front LH side air bag module circuit are • Disconnection of wiring harness and
[SHORT] shorted to each other. short.
• Internal breakdown in front LH side
air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-108, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminal and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use un specified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK FRONT SIDE AIR BAG MODULE
1. Replace front LH side air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1138, B1139, B1140, B1141, B1142, B1143 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and watches such systems as the driver and passenger air bag, D
side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate prop-
erly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694615
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694616
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
RH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
RH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694618
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1145 CURTAIN MODULE RH RH side curtain air bag module circuit is • Disconnection of wiring harness and
[OPEN] open. open.
• Internal breakdown in RH side cur-
tain air bag module. J
• Replace diagnosis sensor unit
(ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-112, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace RH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
RH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
RH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694621
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1146 CURTAIN MODULE RH RH side curtain air bag module circuit is • Disconnection of wiring harness and
[VB-SHORT] shorted to some power supply circuit. short.
• Internal breakdown in RH side cur-
tain air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-114, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace RH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
RH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
RH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694624
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1147 CURTAIN MODULE RH RH side curtain air bag module circuit is • Disconnection of wiring harness and
[GND-SHORT] shorted to ground. short.
• Internal breakdown in RH side cur-
tain air bag module. J
• Replace diagnosis sensor unit
(ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-116, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace RH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
RH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
RH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694627
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1148 CURTAIN MODULE RH RH side curtain air bag module circuit • Disconnection of wiring harness and
[SHORT] are shorted to each other. short.
• Internal breakdown in RH side cur-
tain air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-118, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace RH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694630
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1150 CURTAIN MODULE LH LH side curtain air bag module circuit is • Disconnection of wiring harness and
[OPEN] open. open.
• Internal breakdown in LH side cur-
tain air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-120, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace LH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694633
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1151 CURTAIN MODULE LH LH side curtain air bag module circuit is • Disconnection of wiring harness and
[VB-SHORT] shorted to some power supply circuit. short.
• Internal breakdown in LH side cur-
tain air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-122, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace LH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694636
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“”SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1152 CURTAIN MODULE LH LH side curtain air bag module circuit is • Disconnection of wiring harness and
[GND-SHORT] shorted to ground. short.
• Internal breakdown in LH side cur-
tain airbag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-124, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace LH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE E
LH side curtain air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION F
LH side curtain air bag module is installed on the roof side with fixed bolts.
DTC Logic INFOID:0000000001694639
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1153 CURTAIN MODULE LH LH side curtain air bag module circuit • Disconnection of wiring harness and
[SHORT] are shorted to each other. short.
• Internal breakdown in LH side cur-
tain air bag module. J
• Internal breakdown in diagnosis sen-
sor unit (ACU).
K
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
L
Turn ignition switch ON.
>> GO TO 2. M
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
N
Is malfunctioning part detected?
YES >> Refer to SRC-126, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END.
O
>> GO TO 2.
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK SIDE CURTAIN AIR BAG MODULE
1. Replace LH side curtain air bag module.
2. Check the screen of CONSULT-lll.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
DTC B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT B
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-lll. C
OPERATION
It detects a shock that exceeds specified level and watches such systems as the driver and passenger air bag, D
side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate prop-
erly.
E
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
F
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
G
DTC Logic INFOID:0000000001694642
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK AIR BAG WARNING LAMP
Check the warning lamp status.
Is malfunctioning part detected?
YES >> Refer to SRC-133, "DTC Index".
NO >> INSPECTION END.
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694643
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace wiring harness.
3.CHECK DIAGNOSIS SENSOR UNIT
1. Replace diagnosis sensor unit (ACU).
2. Check the screen of CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE
It consists of crash zone sensor, diagnosis sensor unit (ACU), air bags and seat belt pre-tensioners for driver E
and front passenger.
INSTALLATION F
Refer to SR-14, "Removal and Installation", SR-16, "Removal and Installation", SB-5, "SEAT BELT RETRAC-
TOR : Removal and Installation", SR-4, "Removal and Installation", SR-10, "Removal and Installation".
G
DTC Logic INFOID:0000000001694645
1.INSPECTION START
Turn ignition switch ON. L
>> GO TO 2.
2.CHECK SELF-DIAG RESULT M
With CONSULT-lll
WARNING: P
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK FRONT AIR BAG MODULE
Revision: 2007 June SRC-129 G37 Coupe
B1209 FRONTAL COLLISION DETECTION
< COMPONENT DIAGNOSIS >
Check front air bag module. (driver air bag module and/or passenger air bag module.)
Is the front air bag module deployed?
YES >> Replace front air bag module.
NO >> GO TO 2.
2.CHECK FRONT SEAT BELT PRE-TENSIONER
Check front seat belt pre-tensioner.
Is the front seat belt pre-tensioner activated?
YES >> Replace front seat belt pre-tensioner.
NO >> GO TO 3.
3.CHECK DIAGNOSIS SENSOR UNIT
Check diagnosis sensor unit.
Is the front air bag module and/or front seat belt pre-tensioner activated?
YES >> Replace diagnosis sensor unit (ACU).
NO >> GO TO 4.
4.CHECK STEERING WHEEL
Check steering wheel.
Is the steering wheel normal?
YES >> GO TO 5.
NO >> Replace steering wheel.
5.CHECK SPIRAL CABLE
1. Check the continuity of spiral cable.Refer to SRC-42, "Diagnosis Procedure (Component diagnosis)".
2. Operate the steering wheel to check excessive heavy operation force, abnomal noise or damage.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace spiral cable.
6.CHECK WIRING HARNESS
Check wiring harness.
Is the wiring harness normal?
YES >> GO TO 7.
NO >> Repair or replace wiring harness/harness connector.
7.FINAL CHECK
Check the screen of CONSULT-III and/or Air bag warning lamp status.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
STRUCTURE
It consists of satellite sensor, diagnosis sensor unit (ACU), front side air bag and side curtain air bag. E
INSTALLATION
Refer to SR-15, "Removal and Installation", SR-16, "Removal and Installation", SR-12, "Removal and Installa- F
tion".
DTC Logic INFOID:0000000001694648
G
DTC DETECTION LOGIC
With CONSULT-lll SRC
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
I
B1210 SIDE COLLISION DE- Front side air bag, side curtain air bag is —
TECTION deployed.
J
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START K
Turn ignition switch ON.
L
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll. M
Is malfunctioning part detected?
YES >> Refer to SRC-131, "Diagnosis Procedure (Component diagnosis)".
NO >> INSPECTION END. N
Diagnosis Procedure (Component diagnosis) INFOID:0000000001694649
O
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor) P
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK FRONT SIDE AIR BAG MODULE
Check for front side air bag module.
Is the front side air bag module deployed?
Repair order
Diagnostic item Explanation
“Recheck SRS at each replacement” E
NO DTC IS DETECT- When malfunction is in- • Low battery voltage (Less than 9 V)
ED. dicated by the “AIR
• Self-diagnosis result “SELF-DIAG • Go to SRC-15, "Diagnosis Descrip-
BAG” warning lamp in
[PAST]” (previously stored in the tion". F
User mode.
memory) might not be erased after re-
pair.
• Intermittent malfunction has been de-
tected in the past. G
• No malfunction is detected. —
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1001-B1015] (ACU). SRC
OCCUPANT SENS C/U • Trouble occurs in OCS-CU. 1. Repair or replace wiring harness /
[UNIT FAIL] harness connector. I
[B1017] 2. Replace front passenger seat
[B1020] cushion and occupant classifica-
[B1021] tion system control unit as an as-
semly. J
3. Replace diagnosis sensor unit
(ACU).
OCCUPANT SENS • Trouble occurs in OCS-SENS. 1. Repair or replace wiring harness / K
[UNIT FAIL] harness connector.
[B1018] 2. Replace front passenger seat
cushion and occupant classifica-
tion system control unit as an as- L
semly.
3. Replace diagnosis sensor unit
(ACU).
M
OCCUPANT SENS C/U • Trouble occurs in OCS-CU, circuit of OCS-CU~ACU, or ACU. 1. Repair or replace wiring harness /
[COMM FAIL] harness connector.
[B1022] 2. Replace front passenger seat
cushion and occupant classifica- N
tion system control unit as an as-
semly.
3. Replace diagnosis sensor unit
(ACU). O
PASS A/B INDCTR CKT • Cut-off telltale circuit is open or shorted to ground or the circuits 1. Repair or replace wiring harness /
[B1023] are shorted each other. harness connector.
2. Replace passenger air bag off in- P
dicator.
3. Replace diagnosis sensor unit
(ACU).
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1026-B1031] (ACU).
[OPEN/UPR-VB-
SHORT]
[B1038]
[SHORT/UPR-GND-
SHORT]
[B1040]
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1042-B1047] (ACU).
DRIVER AIRBAG MOD- • Driver air bag module circuit is open. (including the spiral cable.) 1. Repair or replace wiring harness/
ULE harness connector.
[OPEN] 2. Replace driver air bag module.
[B1049] [B1054] 3. Replace spiral cable. Refer to
SRC-42,
DRIVER AIRBAG MOD- • Driver air bag module circuit is shorted to some power supply cir-
"Diagnosis Procedure (Compon
ULE cuit. (including the spiral cable.)
ent diagnosis)".
[VB-SHORT]
4. Replace diagnosis sensor unit
[B1050] [B1055]
(ACU).
DRIVER AIRBAG MOD- • Driver air bag module circuit is shorted to ground. (including the
ULE spiral cable.)
[GND-SHORT]
[B1051] [B1056]
DRIVER AIRBAG MOD- • Driver air bag module circuits are shorted to each other. (includ-
ULE ing spiral cable.)
[SHORT] • Driver air bag module circuit is shorted to itself.
[B1052] [B1057]
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1058-B1063] (ACU).
ASSIST A/B MODULE • Front passenger air bag module circuit is open. 1. Repair or replace wiring harness/
[OPEN] harness connector.
[B1065] [B1070] 2. Replace front passenger air bag
module.
ASSIST A/B MODULE • Front passenger air bag module circuit is shorted to some power
3. Replace diagnosis sensor unit
[VB-SHORT] supply circuit.
(ACU).
[B1066] [B1071]
ASSIST A/B MODULE • Front passenger air bag module circuit is shorted to ground.
[GND-SHORT]
[B1067] [B1072]
ASSIST A/B MODULE • Front passenger air bag module circuits are shorted to each oth-
[SHORT] er.
[B1068] [B1073] • Front passenger air bag module circuit is shorted to itself.
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1074-B1079] (ACU).
SATELLITE SENS RH • RH satellite sensor is out of order. 1. Repair or replace wiring harness/
[UNIT FAIL] harness connector. J
[B1113] 2. Replace RH satellite sensor.
[B1114] 3. Replace diagnosis sensor unit
SATELLITE SENS RH (ACU).
[COMM FAIL] K
[B1115]
[UNMATCH]
[B1116]
L
SATELLITE SENS LH • LH satellite sensor is out of order. 1. Repair or replace wiring harness/
[UNIT FAIL] harness connector.
[B1118] 2. Replace LH satellite sensor.
[B1119] 3. Replace diagnosis sensor unit M
SATELLITE SENS LH (ACU).
[COMM FAIL]
[B1120]
[UNMATCH] N
[B1121]
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1122-B1127] (ACU). O
CURTAIN MODULE RH • RH side curtain air bag module circuit is open. 1. Repair or replace wiring harness/
[OPEN] harness connector.
[B1145] 2. Replace RH side curtain air bag
module.
CURTAIN MODULE RH • RH side curtain air bag module circuit is shorted to some power
3. Replace diagnosis sensor unit
[VB-SHORT] supply circuit.
(ACU).
[B1146]
CURTAIN MODULE RH • RH side curtain air bag module circuit is shorted to ground.
[GND-SHORT]
[B1147]
CURTAIN MODULE RH • RH side curtain air bag module circuits are shorted to each other.
[SHORT] • RH side curtain air bag module circuit is shorted to itself.
[B1148]
CURTAIN MODULE LH • LH side curtain air bag module circuit is open. 1. Repair or replace wiring harness/
[OPEN] harness connector.
[B1150] 2. Replace LH side curtain air bag
module.
CURTAIN MODULE LH • LH side curtain air bag module circuit is shorted to some power
3. Replace diagnosis sensor unit
[VB-SHORT] supply circuits.
(ACU).
[B1151]
CURTAIN MODULE LH • LH side curtain air bag module circuit is shorted to ground.
[GND-SHORT]
[B1152]
CURTAIN MODULE LH • LH side curtain air bag module circuits are shorted to each other.
[SHORT] • LH side curtain air bag module circuit is shorted to itself.
[B1153]
CONTROL UNIT • Diagnosis sensor is out of order. • Replace diagnosis sensor unit
[B1202-B1207] (ACU).
PHIA0532E
SRC
JMHIA0034GB
K
N
JMHIA0045GB
JMHIA0046GB
JMHIA0036GB
JMHIA0033GB
JMHIA0035GB
JMHIA0037GB
JMHIA0038GB
C
JMHIA0039GB
JMHIA0040GB
G
SRC
J
JMHIA0041GB
JMHIA0042GB
JMHIA0043GB
JMHIA0044GB
SRC
JCHWA0101GB
JCHWA0102GB
SRC
O
JCHWA0103GB
JCHWA0104GB
SRC
O
JCHWA0105GB
JCHWA0106GB
Check harness connection between air bag warning lamp and diagnosis sensor unit.
Is the inspection result normal? K
YES >> Check the intermittent incident. Refer to GI-38, "Intermittent Incident".
NO >> Replace wiring harness connector.
L
G
2.CHECK THE SYSTEM 2
Check the seat belt warning lamp function.
SRC
Seat belt warning lamp turns OFF in the following conditions.
• Driver seat belt is fastened.
• Occupant is on passenger seat. I
• Passenger seat belt is fastened.
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Service INFOID:0000000001683005
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-
tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have
elapsed.
• Diagnosis sensor unit must always be installed with their arrow marks “⇐” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.
• The spiral cable must be aligned in the neutral position since its rotations are limited. Do not turn steering
wheel and column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.
Precaution for Battery Service INFOID:0000000002912447
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Occupant Classification System INFOID:0000000001837806
• Replace occupant classification system control unit and passenger front seat cushion as an assembly.
Refer to SE-152, "Removal and Installation".