Professional Documents
Culture Documents
Msds 3
Msds 3
Product Name:
LLDPE
Reactivity
Linear Low Density Polyethylene Flammability
Health
2. COMPOSITION/INFORMATION ON INGREDIENTS
Substances present at a concentration below the Within the present knowledge of the
minimum danger: supplier, this product does not contain any
hazardous ingredients in quantities
requiring to report in this section, in
accordance with EU or national
regulations.
Other component: None
3. IDENTIFICATION OF HAZARDS
Product Name:
LLDPE
Reactivity
Linear Low Density Polyethylene Flammability
Health
Product Name:
LLDPE Reactivity
Linear Low Density Polyethylene Flammability
Health
6
Material Safety Data Sheet (MSDS) Page: 4 of 8
According to the Directives 91/155/CEE-2001/58/CE-ISO 11014-1 Revision Number: 1
Product Name:
LLDPE Reactivity
Linear Low Density Polyethylene Flammability
Health
The regulations relating to storage premises apply to workshop where the product is handled
Handling: Use with adequate ventilation. Local
exhaust ventilation should be provided.
Avoid creating dusty conditions and
prevent wind dispersal. Use explosion-proof
electrical (ventilating, lighting and material
handling) equipment. Take measures
against static discharge. Keep away from
sources of ignition.
Storage: Store in a fireproof location. Keep away
from incompatible materials and avoid
specific conditions. Containers should be
grounded. Take precautionary measures
against electrostatic discharges. Do not
stack more than 2 pallets high in
connection with risk of falling over. Do not
stack pallets with grades containing slip or
Anti-Block (AB) additives. Protect from
(sun) light. Keep in a dry place.
Unsuitable : mild steel
Suitable : stainless steel / Aluminum /
polyethylene
Product Name:
LLDPE Reactivity
Linear Low Density Polyethylene Flammability
Health
Eye protection:
Respiratory protection: Safety glasses with side shields.
Hand protection: Wear dust protection mask P2.
When handling hot material, wear heat-
resistant protective gloves that are able to
withstand the temperature of molten
Skin and body protection: product.
Health measures: Working clothes.
Environmental exposure controls: Not available
Plastic pellets are defined as a "significant
material" which requires any industrial
plant that may expose pellets to storm water
to secure a storm water permit. Violations of
the rule carry the same penalties as other
Clean Water Act violations.
9. PHYSICAL AND CHEMICAL PROPERTIES
None
Solid. (Granular solid. Powder.)
General information: Off-white.
Appearance (at 20°C): Wax-like when heated , characteristic
Colour: Not applicable.
Odour: 125-145
PH (at 20°C): Decomposes. >300 °C
Freezing /Melting point (°C): >345 °C
Boiling point/range (°C): Flammability Risk 1 (Slight)
Flash point (°C): > 330 °C
Flammability: None
Auto-ignition temperature: None
Explosive properties: Not available
Oxidising properties: 0.91 to 0.95 g/cm3
Vapour pressure (at 20°C): 480-560 (pellet) , 300-320 (powder )
Density (at 20°C): water solubility: Insoluble in cold water
Bulk density ( Kg/M3) solubility in fats: Insoluble
Solubility (at 20°C): Not applicable
Not applicable
Viscosity (40°C): Rapid movement of particles or pellets through
Evaporation rate: transfer lines generates static electricity.
Other information:
8
Material Safety Data Sheet (MSDS) Page: 6 of 8
According to the Directives 91/155/CEE-2001/58/CE-ISO 11014-1 Revision Number: 1
Product Name:
LLDPE Reactivity
Linear Low Density Polyethylene Flammability
Health
Product Name:
LLDPE Reactivity
Linear Low Density Polyethylene Flammability
Health
Other adverse effects: No specific ecological data are available for this
product.
None
10
Material Safety Data Sheet (MSDS) Page: 8 of 8
According to the Directives 91/155/CEE-2001/58/CE-ISO 11014-1 Revision Number: 1
Product Name:
LLDPE Reactivity
Linear Low Density Polyethylene Flammability
Health
The contents and format of this MSDS are in accordance with EEC Commission Directive 2001/58/EC
Disclaimer of liability:
The information in this MSDS was obtained from different sources, which National Petrochemical
Company (NPC) and Iran Petrochemical Commercial Company (IPCC) believe, are reliable. However, the
information is provided without any warranty, express or implied, regarding its correctness. The conditions
or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond
our knowledge. For this and other reasons, National Petrochemical Company (NPC) and Iran
Petrochemical Commercial Company (IPCC) do not assume responsibility and expressly disclaim liability
for loss, damage or expense arising out of or in any way connected with the handling, storage, use or
disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is
used as a component in another product, this MSDS information may not be applicable.
11