CCV Technical Document

Characterized Control Valves™ (CCV)
Features and Benefits
EQUAL PERCENTAGE VALVE CHARACTERISTIC

In order to ensure good stability of control, it is essential
Patented Technology for a control valve to have an equal percentage
characteristic. This type of characteristic produces a
linear variation in thermal output according to the
amount of opening of the valve (also known as
the system characteristic). Under normal testing
conditions a conventional ball valve exhibits an
S-shaped characteristic. When it is installed in a
real system, however, this characteristic is
seriously deformed because, compared with its
nominal size, a ball valve possesses an extremely
high flow coefficient. Whether used with or without
pipe reducers or a reduced bore, they do not normally
BENEFIT OF THE BELIMO CHARACTERIZING DISC allow stable regulation of the thermal capacity.
Belimo’s unique Characterized Control Valve™ (CCV) is very
● Equal percentage flow characteristic. different. A special characterizing disc inside the valve gives it an equal
● Excellent control stability assured with the characterizing disc. percentage characteristic which is comparable with that of a globe valve
of the same nominal size. The flow (the Cv value) is reduced to the
● Cv values equal to Cv values of globe valves the same size. required value by a combination of the hole in the ball and the shaped
P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.
● The need for multiple pipe reduction is usually eliminated. aperture in the disc. The increase in flow as the valve is opened is very
slow and controlled.
● Better control prevents “hunting” of the control loop, increasing
This produces better part-load behavior and improved stability of
life span of actuator and valve.
control while also optimizing energy consumption.
FEATURES
● Thermal isolating adapter between ● Vent holes reduce

flange and actuator. condensation build-up.
● Easy direct coupling of actuator ● Forged brass valve body — no
with a single screw. pin-hole leaks.
● Perpendicular mounting flange and ● Characterizing disc — made of Tefzel®
square drive head eliminate lateral known for excellent strength and
forces on the stem. chemical resistance.
● Blow-out proof stem with thrust-bearing ● Teflon® seats with O-rings provide
Teflon® disc and double O-ring design constant seating force against the ball
for long service life.* and reduce torque requirement.
● Non-corroding chrome-plated ● Actuator can be mounted in four
brass or stainless ball. different positions.
* Designed for service life of over 100,000 full cycles.

Teflon® and Tefzel® are both registered trademarks of Dupont.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
1
Feature / Benefits
COORDINATED MOTORIZED OPERATION Flow Characteristics of Conventional Ball Valves

versus BELIMO CHARACTERIZED CONTROL VALVES
The optimum functionality of the Belimo CCV is assured by properly
coordinating its actuation with MFT. Specially developed rotary
actuators provide the necessary precision for modulating, floating-
point, and on/off methods of control.
All CCVs are supplied with the appropriate rotary actuator to provide Stable
the close-off and operation desired. control is
hard to
achieve
OPTIMIZED FOR CONTROL
The Belimo CCV marries known technology with an innovative
development – the unique characterizing disc.
The marriage of CCV and MFT technologies has produced a range of
valuable features which surpass the capabilities of globe valves at a
very attractive price level:
● An equal-percentage valve characteristic
● Unlike a globe valve, no sudden change in inlet flow upon opening
● Excellent stability of control
● Cv values comparable with those of globe valves of the same size Desirable
or larger valve
● Higher close-off ratings than standard globe valves authority
● 100% tight shut-off on two-way valves means NO leak-by unlike is not
globe valves that have ANSI IV shutoff (leakage rate of 0.01% of achieved
the Cv rating)
● Three-way valve can be piped in mixing or diverting application
B2 Series Two-way ½” to 3”
B3 Series Three-way ½” to 2”
Mixing*/Diverting

B6 Series Two-way Flanged 2½” to 6”
Service: Chilled/hot water, 60% glycol

Cv Range 0.3-240
Material: Stainless trim or Brass trim
Control: On/Off, Floating, 2-10 VDC
Multi-Function Technology®
Spring Return or Non-Spring Return
Mixing* (Not for use in change over applications)
Desirable Equal Percent Flow and resulting

heat output is achieved with linear results
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
2
Sizing/Selection
2-Way Valve Flow Rate for Water Applications (Gallons Per Minute, GPM)
Cv Pressure Drop Across the Valve

DN 2-Way
Maximum Inches
mm CCV 1 psi 2 psi 3 psi 4 psi 5 psi 6 psi 7 psi 8 psi 9 psi 10 psi
Rating
0.3 ½” 15 B207(B) 0.3 0.4 0.5 0.6 0.7 0.7 0.8 0.8 0.9 0.9
0.46 ½” 15 B208(B) 0.5 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
0.8 ½” 15 B209(B) 0.8 1.1 1.4 1.6 1.8 2.0 2.1 2.3 2.4 2.5
1.2 ½” 15 B210(B) 1.2 1.7 2.1 2.4 2.8 2.9 3.2 3.4 3.6 3.8
1.9 ½” 15 B211(B) 1.9 2.7 3.3 3.8 4.2 4.7 5.0 5.4 5.7 6.0
3 ½” 15 B212(B) 3.0 4.2 5.2 6.0 6.8 7.3 7.9 8.5 9.0 9.5
4.7 ½” 15 B213(B) 4.7 6.6 8.1 9.4 11 12 12 13 14 15
7.4 ½” 15 B214(B) 7.4 10 13 15 17 18 20 21 22 23
10 ½” 15 B215(B)* 10 14 17 20 22 24 26 28 30 32
16 ½” 15 B216(B)* 14 20 24 28 31 34 37 40 42 44
4.7 ¾” 20 B217(B) 4.7 6.6 8.1 9.4 11 12 12 13 14 15
7.4 ¾” 20 B218(B) 7.4 10 13 15 17 18 20 21 22 23
10 ¾” 20 B219(B) 10 14 17 20 22 24 26 28 30 32
14 ¾” 20 B220(B)* 14 20 24 28 31 34 37 40 42 44
24 ¾” 20 B221(B)* 24 34 42 48 54 59 63 68 72 76
7.4 1” 25 B222 7.4 10 13 15 17 18 20 21 22 23
10 1” 25 B223 10 14 17 20 22 24 26 28 30 32
19 1” 25 B224 19 27 33 38 42 47 50 54 57 60
30 1” 25 B225* 30 42 52 60 67 73 79 85 90 95
10 1¼” 32 B229 10 14 17 20 22 24 26 28 30 32
19 1¼” 32 B230* 19 27 33 38 42 47 50 54 57 60
25 1¼” 32 B231 25 35 43 50 56 61 66 71 75 79
37 1¼” 32 B232* 37 52 64 74 83 91 98 105 111 117
19 1½”” 40 B238 19 27 33 38 42 47 50 54 57 60
29 1½” 40 B239 29 41 50 58 65 71 77 82 87 92
37 1½” 40 B240* 37 52 64 74 83 91 98 105 111 117
29 2” 50 B248 29 41 50 58 65 71 77 82 87 92
46 2” 50 B249 46 65 80 92 103 113 122 130 138 145
57 2” 50 B250* 57 81 99 114 127 140 151 161 171 180
65 2” 50 B251 65 92 113 130 145 159 170 194 195 206
85 2” 50 B252 85 120 147 170 190 208 225 240 255 269
120 2” 50 B253 120 170 208 240 268 294 318 339 360 380
240 2” 50 B254* 240 339 416 480 537 588 635 679 720 759
60 2½” 65 B261 60 85 104 120 134 147 159 170 180 190
75 2½” 65 B262 75 106 130 150 168 194 198 212 225 237
110 2½” 65 B263 110 156 191 220 246 269 291 311 330 348
150 2½” 65 B264 150 212 260 300 335 367 397 424 450 474
210 2½” 65 B265* 210 297 364 420 470 514 556 594 630 664
70 3” 80 B277 70 99 121 140 157 172 185 198 210 221
130 3” 80 B278 130 194 225 260 290 318 344 368 390 411
170 3” 80 B280* 170 240 294 340 380 416 450 481 510 538
70 2½” 65 B6250S-070 70 99 121 140 157 171 185 198 210 221
110 2½” 65 B6250S-110 110 156 191 220 244 266 282 296 312 320
110 3” 80 B6300S-110 110 156 191 220 244 266 282 296 312 320
186 4" 100 B6400S-186 186 263 322 372 416 456 492 526 558 588
290 5" 125 B6500S-290 290 410 502 580 648 710 767 820 870 917
400 6" 150 B6600S-400 400 566 693 800 894 980 1058 1131 1200 1265
GPM = Cv x ∆p
*Models with no characterizing disc.
The influence of the pipe geometry due to reduced flow is negligible for all valves 57 Cv and below with characterizing discs.
3
Sizing/Selection
3-Way Valve Flow Rate for Water Applications (Gallons Per Minute, GPM)
Cv Pressure Drop Across the Valve

DN 3-Way
Maximum Inches
mm CCV 1 psi 2 psi 3 psi 4 psi 5 psi 6 psi 7 psi 8 psi 9 psi 10 psi
Rating
0.3 ½” 15 B307(B) 0.3 0.4 0.5 0.6 0.7 0.7 0.8 0.8 0.9 0.9
0.46 ½” 15 B308(B) 0.5 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
0.8 ½” 15 B309(B) 0.8 1.1 1.4 1.6 1.8 2.0 2.1 2.3 2.4 2.5
1.2 ½” 15 B310(B) 1.2 1.7 2.1 2.4 2.8 2.9 3.2 3.4 3.6 3.8
1.9 ½” 15 B311(B) 1.9 2.7 3.3 3.8 4.2 4.7 5.0 5.4 5.7 6.0
3 ½” 15 B312(B) 3.0 4.2 5.2 6.0 6.8 7.3 7.9 8.5 9.0 9.5
4.7 ½” 15 B313(B) 4.7 6.6 8.1 9.4 11 12 12 13 14 15
10 ½” 15 B315(B)* 10 14 17 20 22 24 26 28 30 32
16 ½” 15 B316(B)* 14 20 24 28 31 34 37 40 42 44
4.7 ¾” 20 B317(B) 4.7 6.6 8.1 9.4 11 12 12 13 14 15
7.4 ¾” 20 B318(B) 7.4 10 13 15 17 18 20 21 22 23
14 ¾” 20 B320(B)* 14 20 24 28 31 34 37 40 42 44
24 ¾” 20 B321(B)* 24 34 42 48 54 59 63 68 72 76
7.4 1” 25 B222 7.4 10 13 15 17 18 20 21 22 23
10 1” 25 B223 10 14 17 20 22 24 26 28 30 32
30 1” 25 B325* 30 42 52 60 67 73 79 85 90 95
10 1¼” 32 B329 10 14 17 20 22 25 27 28 30 32
19 1¼” 32 B330 19 27 33 38 43 47 50 54 57 60
25 1¼” 32 B331 25 35 43 50 56 61 66 71 75 79
19 1½” 40 B338 19 27 33 38 43 47 50 54 57 60
29 1½” 40 B339 29 41 50 58 65 71 77 82 87 92
37 1½” 40 B340 37 52 64 74 83 91 98 105 111 117
46 1½” 40 B341 46 65 80 92 103 113 122 130 138 146
29 2” 50 B347 29 41 50 58 65 71 77 82 87 92
37 2” 50 B348 37 52 64 74 83 91 98 105 111 117
46 2” 50 B349 46 65 80 92 103 113 122 130 138 146
57 2” 50 B350 57 81 99 114 128 140 151 161 171 180
68 2” 50 B351 68 96 118 136 152 167 180 192 204 215
83 2” 50 B352 83 117 144 166 186 204 220 235 249 263
GPM = Cv x ∆p * = Models with no characterizing disc.

The influence of the pipe geometry due to reduced flow is negligible for all valves 83 Cv and below with characterizing discs.
4
Set-up and Wiring Instructions
SET-UP
2-WAY VALVE 3-WAY VALVE
SPECIFY UPON ORDERING SPECIFY UPON ORDERING
TR24-3-T US Power to pin 2 will Power to pin 2 will

TR24-3 US drive valve CCW. drive valve CCW.
On/Off or Power to pin 3 will Power to pin 3 will
Floating Point Actuators drive valve CW. drive valve CW.
NON-SPRING RETURN
Stays in Last Position
TR24-SR-T US NC: Closed A to AB, will NO: Open A to AB, will close NC: Closed A to AB, will NO: Open A to AB, will close
TR24-SR US open as voltage increases. as voltage increases. open as voltage increases. as voltage increases.
Proportional (Can be chosen with (Can be chosen with
Type Actuators switch inside terminal switch inside terminal
block of actuator.) block of actuator.)
LRB24 (-3), MFT, SR Power to pin 2 will drive NO: Open A to AB, will close Power to pin 2 will drive NO: Open A to AB, will close
LRX24 (-3), MFT, SR valve CW. Power to pin 3 as voltage increases or valve CW. Power to pin 3 as voltage increases or
ARB24 (-3), MFT, SR will drive valve CCW. The power applied. (Can be will drive valve CCW. The power applied. (Can be
ARX24 (-3), MFT, SR above will function when chosen with CW/CCW above will function when chosen with CW/CCW
Floating Point or the directional switch is in switch.) the directional switch is in switch.)
Proportional Type Actuators the “1” position, to reverse the “1” position, to reverse
select the “0” position. select the “0” position.
TFRB24 NO/FO Valve: Open A to AB NC/FC Valve: Closed A to AB NO/FO Valve: Open A to AB NC/FC Valve: Closed A to AB
LF24 US will drive closed. will drive open. will drive closed. will drive open.
AFRB24 Spring Action: Spring Action: Spring Action: Spring Action:
Will spring open A to AB Will spring closed A to AB Will spring open A to AB Will spring closed A to AB
upon power loss. upon power loss. upon power loss. upon power loss.
TF (-3), MFT, SR NC/FO Valve: Closed A to AB NC/FC or NO/FC NC/FO Valve: Closed A to AB NC/FC or NO/FC
SPRING RETURN
Note Fail Position
LF (-3), MFT, SR will drive open. Valve: Closed A to AB or will drive open Valve: Closed A to AB
AF SR Spring Action: Open A to AB. Spring Action: or Open A to AB.
AFR, MFT Will spring open A to AB (Can be chosen with Will spring open A to AB (Can be chosen with
Floating Point or upon power loss. CW/CCW switch.) upon power loss. CW/CCW switch.)
Proportional Type Actuators Spring Action: Spring Action:
Will spring closed A to AB Will spring closed A to AB

upon power loss. upon power loss.
NO/FO Valve: Open A to AB NO/FO Valve: Open A to AB

Spring Action: Spring Action:
Will spring open A to AB Will spring open A to AB
upon power loss. upon power loss.
(NO action can be chosen (NO action can be chosen
with CW/CCW switch.) with CW/CCW switch.)
GENERAL WIRING INSTRUCTIONS

WARNING The wiring technician must be trained and experienced with in the field, there are no parts or components to be replaced or repaired.
electronic circuits. Disconnect power supply before attempting any – EMC directive: 89/336/EEC
wiring connections or changes. Make all connections in accordance with – Software class A: Mode of operation type 1
wiring diagrams and follow all applicable local and national codes.
– Low voltage directive: 73/23/EEC
Provide disconnect and overload protection as required. Use copper,
twisted pair, conductors only. If using electrical conduit, the attachment CAUTION It is good practice to power electronic or digital controllers
to the actuator must be made with flexible conduit. from a separate power transformer than that used for actuators or other
end devices. The power supply design in our actuators and other end
Always read the controller manufacturer's installation literature
devices use half wave rectification. Some controllers use full wave
carefully before making any connections. Follow all instructions in this
rectification. When these two different types of power supplies are
literature. If you have any questions, contact the controller manufacturer
connected to the same power transformer and the DC commons are
and/or Belimo.
connected together, a short circuit is created across one of the diodes in
Transformer(s) the full wave power supply, damaging the controller. Only use a single
Belimo actuators require a 24 VAC class 2 transformer and draws a power transformer to power the controller and actuator if you know the
controller power supply uses half wave rectification.
maximum of 10 VA per actuator. The actuator enclosure cannot be opened
5
Flow, Operation and Installation
FLOW PATTERNS
2-way Characterized Control Valves™ (Belimo B2 Series) (Belimo B6 Series) Flow Direction
Two-way valves
should be installed
with the disc
upstream.
Upstream A
Downstream AB
3-way Characterized Control Valves™ (Belimo B3 Series)

MIXING (Not for use in change over applications DIVERTING
The A-port must

be piped to the coil
to maintain proper
control.
INCORRECT PIPING
The A-port must be piped to the coil to maintain proper control.
Three-Way
y Diverting
Diver Valve
lve Piping Diagram WARNING! Do Not Pipe in this manner!
Three-Wa
Way
y Mixing Valvelve Piping Diagram
Diagra
(2 Inputs,
Inputs, 1 Output)
Output (1 Input, 2 Outputs) Note Valve Porting!
A
A The A-port must be piped to the coil! Not the B-port!
B
B ReturnReturn ReturnReturn Flow is not possible from A to B. If AB-port is not piped as
Coil AB
AB Coil Coil the common port, the valve must be re-piped. It is good
Coil A
A
practice to install a balancing valve in the bypass line. These
SupplySupply SupplySupply
B
B valves are intended for closed loop systems. Do not install
AB
AB in an open loop system or in an application that is open to
atmospheric pressure.
OPERATION/INSTALLATION – CORRECT PIPING

2-way valves should be installed with the characterizing discs upstream. No damage to the valve will result if installed incorrectly with the characterizing discs
downstream.
3-WAY VALVES MUST BE PIPED CORRECTLY. They can be mixing or diverting. Mixing is the preferred piping arrangement.
Diverting* (Not for use in change over applications)
The BELIMO Characterized Control Valve is a CONTROL valve, not a manual valve adapted for actuation. The control port is the A-port. It is similar to the globe valve in that
the middle port is the B or bypass port. The common port AB is on the main opposite the A-port. These diagrams are for typical applications only. Consult engineering
specification and drawings for particular circumstances.
REDUCED B-PORT FLOW
Note: The B-port flow of the 3-way CCV is lower than that of the A-port. In most applications this is beneficial since the reduced flow compensates for the inexistent
pressure drop across the coil in the bypass mode. Therefore, proper sizing is important to avoid flow noise in particular when the system is designed with constant
speed pumps. Please refer to our valve sizing and selection guidelines.
The flow velocity in the pipe upstream and downstream of the valve should be considered as well. The typical HVAC design maximum flow is 4 to 8 ft/s to avoid noise
issues.
Also, the pipe reduction factor must be considered and can be found on pages 3 and 4. Pipe reducers decrease the Cv value of a valve and consequently increase the
pressure drop across the valve, a situation that could lead to noise or a lower than designed flow.
Diverting* (Not for use in change over applications)

6
Nomenclature
Characterized Control Valve™ (CCV)
B2 09 +LRX 24 -MFT
Valve Valve Size Trim Material Actuator Type Power Supply Control
B2 = 2-way 07-80 = ½” to 3” B = Chrome Plated Non Fail-Safe 24 = 24 VAC/DC Blank = On/Off -S = Built-in
B3 = 3-way Brass Ball, TR 120 = 120 VAC* -3 = On/Off, Floating Point Auxiliary
Nickel Plated LRB, LRX 230 = 230 VAC -SR = 2-10 VDC Switch
Stem LRQX UP = 24 to 240 VAC -MFT = Multi-Function -T = Terminal
Blank = Stainless NRB, NRX Technology Strip
Steel Ball NRQX -MFT95 = 0-135 Ω N4 = NEMA
and Stem ARB, ARX 4/4X
-IP = Internet Protocol
ARQX N4H = NEMA
Fail-Safe 4/4X
Spring Return with
TFR, TFRX Heater
LF
AFR, AFRX
Electronic
GKR
*LR and AR include 120-240 VAC
Ordering Example
3 For MFT Orders Only - Select Programming Code

1 Choose the valve actuator combination.
B209+LRX24-MFT NO Tagging (if needed)

4
2 Specify preference or configuration.
Does order
require
Set-Up tagging?
Non Fail-Safe Models

P-10001 (A01) Tagging:
NO = Normally Open Valves may be
P-100xx (Axx) Control voltage applications
NC = Normally Closed tagged per customer
P-200xx (Wxx) Pulse width modulation specification. ($10.00
Fail-Safe Models applications charge per tag)
NO/FO = Normally Open/Fail Open P-300xx (Fxx) Floating Point applications
NO/FC = Normally Open/Fail Closed P-400xx (Jxx) On/Off applications Example:
X-XXXXX Create custom MFT AHU-1
NC/FO = Normally Closed/Fail Open FCU-2
configuration code
NC/FC = Normally Closed/Fail Closed
X-XXXXX Create custom MFT
Part number for
See settings configuration in the field
tagging: 99981-00101
Refers to valve ports A to AB. with MFT-actuator PC-Tool software
5 Complete Ordering Example: B209+LRX24-MFT

Configuration:
+NO
Programming: +A01
7
Nomenclature
Characterized Control Valve™ (CCV)
B6 250 S -070 +GRX 24 -MFT

Valve Valve Size Trim Material Cv Actuator Type Power Supply Control
B6 = 2-way 250-600 = 2½” S = Stainless 070 = 70 Cv Non Fail-Safe 24 = 24 VAC/DC Blank = On/Off N4 =
Flanged to 6” Steel Ball and 110 = 110 Cv ARB, ARX 120 = 120 VAC* -3 = On/Off, Floating NEMA 4/4X
Stem 186 = 186 Cv GRB, GRX 230 = 230 VAC Point N4H =
290 = 290 Cv Fail-Safe UP = 24 to 240 VAC -SR = 2-10 VDC NEMA 4/4X
with Heater
400 = 400 Cv Spring Return -MFT = Multi-Function
AFRB, AFRX Technology
Electronic -MFT95 = 0-135 Ω
GKRB, GKRX -IP = Internet Protocol
*AR includes 120-240 VAC
Ordering Example
3 For MFT Orders Only - Select Programming Code

1 Choose the valve actuator combination.

B6250S-070+GRX24-MFT NO Tagging (if needed)
4
2 Specify preference or configuration.
Does order
require
Set-Up tagging?
Non Fail-Safe Models

P-10001 (A01) Tagging:
NO = Normally Open Valves may be
P-100xx (Axx) Control voltage applications
NC = Normally Closed tagged per customer
P-200xx (Wxx) Pulse width modulation specification. ($10.00
Fail-Safe Models applications charge per tag)
NO/FO = Normally Open/Fail Open P-300xx (Fxx) Floating Point applications
NO/FC = Normally Open/Fail Closed P-400xx (Jxx) On/Off applications Example:
X-XXXXX Create custom MFT AHU-1
NC/FO = Normally Closed/Fail Open FCU-2
configuration code
NC/FC = Normally Closed/Fail Closed
X-XXXXX Create custom MFT
Part number for
See settings configuration in the field
tagging: 99981-00101
Refers to valve ports A to AB. with MFT-actuator PC-Tool software
5 Complete Ordering Example: B6250S-070+GRX24-MFT

Configuration:
+NO
Programming: +A01
8
B2 Series, 2-Way, Characterized Control Valve
Chrome Plated Brass Ball and Brass Stem
Application
This valve is typically used in air handling units on heating or cooling coils, and
fan coil unit heating or cooling coils. Some other common applications include
Unit Ventilators, VAV box re-heat coils and bypass loops. This valve is suitable
for use in a hydronic system with variable flow.
Valve Nominal Size Type Suitable Actuators

Technical Data Cv Inches DN [mm] 2-way NPT Non-Spring Spring
Service chilled or hot water, 60% glycol 0.3 ½ 15 B207B
Flow characteristic A-port equal percentage 0.46 ½ 15 B208B
Controllable Flow Range 75° 0.8 ½ 15 B209B
Sizes ½”, ¾” 1.2 ½ 15 B210B
Type of end fitting NPT female ends 1.9 ½ 15 B211B
Materials: 3 ½ 15 B212B
Body forged brass, nickel plated
TR Series
LR Series
4.7 ½ 15 B213B
TF Series
LF Series
Ball chrome plated brass 7.4 ½ 15 B214B
Stem nickel plated brass 10 ½ 15 B215B
Seats PTFE 16 ½ 15 B216B
Characterizing disc Tefzel® 4.7 ¾ 20 B217B
Packing 2 EPDM O-rings, lubricated
7.4 ¾ 20 B218B
Body pressure rating 600 psi
10 ¾ 20 B219B
Media temp. range 0°F to 250°F [-18°C to 120°C]
14 ¾ 20 B220B
Close off pressure 200 psi
24 ¾ 20 B221B*
Maximum differential 50 psi for typical applications
*Models without characterizing disc
pressure (∆P)
Leakage 0% for A to AB
External leakage according to EN 12266-1:2003
Cv rating A-port: see product chart for values
Tefzel® is a registered trademark of DuPont
Dimensions
2WayValve-B207-B220
Valve Nominal Size Dimensions (Inches [mm])

Valve Body Inches DN [mm] A B
B207B-B211B ½” 15 2.38” [60.8] 1.39” [35.2]
B212B-B216B ½” 15 2.38” [60.8] 1.78” [45.2]
B217B-B221B ¾” 20 2.73” [69.3] 1.87” [47.4]
Flow Patterns
9
Chrome Plated Brass Ball and Brass Stem
Application
for use in a hydronic system with variable or constant flow.
* (Not for use in change over applications)

Cv Inches DN [mm] 3-way NPT Non-Spring Spring
0.3 ½ 15 B307B
0.46 ½ 15 B308B
0.8 ½ 15 B309B
Technical Data 1.2 ½ 15 B310B
Service chilled or hot water, 60% glycol 1.9 ½ 15 B311B
Flow characteristic A-port equal percentage
TR Series
LR Series
TF Series
LF Series
3 ½ 15 B312B
B-port modified for constant common port 4.7 ½ 15 B313B
flow
10 ½ 15 B315B
Controllable Flow Range 75°
16 ½ 15 B316B
Sizes ½”, ¾”
4.7 ¾ 20 B317B
Type of end fitting NPT female ends
7.4 ¾ 20 B318B
Materials:
14 ¾ 20 B320B
Body forged brass, nickel plated
24 ¾ 20 B321B
Ball chrome plated brass
Stem nickel plated brass
Seats PTFE
Characterizing disc Tefzel®
Body pressure rating 600 psi
Close off pressure 200 psi
pressure (∆P)
<2.0% for B to AB

B-port: 70% of A to AB Cv
Tefzel® is a registered trademark of DuPont
Dimensions
3WayValve-B307-B320

Valve Body Inches DN [mm] A B C
B307B-B311B ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
B312B-B316B ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
B317B-B321B ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Flow Patterns
“B” Port must
be piped to the
bypass leg.
10
Stainless Steel Ball and Stem
Application
for use in a hydronic system with variable flow.

Cv Inches DN [mm] 2-Way NPT Non-Spring Spring
0.3 ½ 15 B207
0.46 ½ 15 B208
0.8 ½ 15 B209
1.2 ½ 15 B210
1.9 ½ 15 B211
Technical Data 3 ½ 15 B212
TR Series
TF Series
Service chilled or hot water, 60% glycol 4.7 ½ 15 B213
Flow characteristic A-port equal percentage 7.4 ½ 15 B214
Controllable Flow Range 75° 10 ½ 15 B215
NR...N4 Series
Sizes ½”, ¾”, 1”, 1¼”, 1½”, 2”, 2½”, 3”
LR Series
LF Series
16 ½ 15 B216
Type of end fitting NPT female ends 4.7 ¾ 20 B217
Materials: 7.4 ¾ 20 B218
Body forged brass, nickel plated 10 ¾ 20 B219
Ball stainless steel
14 ¾ 20 B220
Stem stainless steel
24 ¾ 20 B221*
Seats PTFE
Characterizing disc Tefzel® 7.4 1 25 B222
Packing 2 EPDM O-rings, lubricated 10 1 25 B223
Body pressure rating 19 1 25 B224
600 psi ½” - 1¼” (B230) 30 1 25 B225*
400 psi 1¼” (B231) - 3” 10 1¼ 32 B229
Media temp. range 0°F to 250°F [-18°C to 120°C] 19 1¼ 32 B230*
Close off pressure 25 1¼ 32 B231
200 psi ½” - 2” (B254) 37 1¼ 32 B232*
100 psi 2½” (B261) - 3” 19 1½ 40 B238
Maximum differential 50 psi for typical applications 29 1½ 40 B239
pressure (∆P) 37 1½ 40 B240*
Leakage 0% for A to AB 29 2 50 B248
External leakage according to EN 12266-1:2003 46 2 50 B249

Cv rating A-port: see product chart for values 57 2 50 B250*
AR...N4 Series
Tefzel® is a registered trademark of DuPont 65 2 50 B251
AR Series
AF Series
85 2 50 B252
Dimensions 120 2 50 B253
240 2 50 B254*
2WayValve-B207-B220
60 2½ 65 B261
75 2½ 65 B262
110 2½ 65 B263
150 2½ 65 B264
210 2½ 65 B265*
70 3 80 B277
130 3 80 B278
Valve Nominal Size Dimensions (Inches [mm]) 170 3 80 B280*
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Flow Patterns
B212-B216 ½” 15 2.38” [60.4] 1.78” [45.2]
B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
11
B3 Series, Three Way, Characterized Control Valve
Application
* (Not for use in change over applications)

Cv Inches DN [mm] 3-Way NPT Non-Spring Spring
0.3 ½ 15 B307
0.46 ½ 15 B308
0.8 ½ 15 B309
1.2 ½ 15 B310
1.9 ½ 15 B311
TR Series
TF Series
Technical Data 3 ½ 15 B312
NR...N4 Series
Service chilled or hot water, 60% glycol 4.7 ½ 15 B313
LR Series
LF Series
Flow characteristic A-port equal percentage 10 ½ 15 B315
B-port modified for constant common port 16 ½ 15 B316
flow 4.7 ¾ 20 B317
Controllable Flow Range 75° 7.4 ¾ 20 B318
Sizes ½”, ¾”, 1”, 1¼”, 1½”, 2” 14 ¾ 20 B320
Type of end fitting NPT female ends 24 ¾ 20 B321
Materials: 7.4 1 25 B322
Body forged brass, nickel plated 10 1 25 B323
Ball stainless steel 30 1 25 B325*
Stem stainless steel 10 1¼ 32 B329
Seats PTFE 19 1¼ 32 B330
Characterizing disc Tefzel® 25 1¼ 32 B331
Packing 2 EPDM O-rings, lubricated 19 1½ 40 B338
Body pressure rating 29 1½ 40 B339
AR...N4 Series
600 psi ½” - 1”
AR Series
AF Series
37 1½ 40 B340
400 psi 1¼” - 2”
46 1½ 40 B341
29 2 50 B347
Close off pressure
37 2 50 B348
200 psi ½” - 2”
46 2 50 B349
pressure (∆P) 57 2 50 B350

Leakage 0% for A to AB 68 2 50 B351
<2.0% for B to AB 83 2 50 B352
B-port: 70% of A to AB Cv Flow Patterns
Tefzel® is a registered trademark of DuPont “B” Port must
be piped to the
bypass leg.
Dimensions
3WayValve-B307-B320

B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
B312-B316 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
12
B6 Series, Two Way, Characterized Control Valve
Application
Valve Nominal Type Suitable Actuators

Size
Technical Data DN Electronic
Cv Inches 2-way Flange Non-Spring Spring
Service chilled or hot water, 60% glycol [mm] Fail-Safe
Flow characteristic A-port equal percentage 70 2½" 65 B6250S-070
Series
Series
AFR
110 2½" 65 B6250S-110
AR
Controllable Flow Range 75°
Sizes 2½”, 3”, 4”, 5”, 6” 110 3" 80 B6300S-110
Type of end fitting pattern to mate with ANSI 125 flange 186 4" 100 B6400S-186
Series
Series
290 5" 125 B6500S-290
GKR
Materials:
GR
Body cast iron - GG25 400 6" 150 B6600S-400
Seats PTFE
Characterizing disc stainless steel
Packing 2EEPDM O rings, lubricated
Body pressure rating according to ANSI 125, standard class B Flow Pattern
Media temp. range 0°F to 248°F [-18°C to +120°C]
Close off pressure 100 psi 2-way B6250 to B6600 Characterized Control Valves™
Maximum differential 50 psi
C Flow Direction
pressure (∆P)
Dimensions B
Upstream A
E
Downstream AB
A
F D
Nominal Top Flange

Valve Flange Face-to-Face A Bolt Circle Bolt Hole Number of
Pipe Flange Height Thickness
Body Diameter Length Diameter Diameter Bolt Holes
Size Design F D Minimum
A B C D E F
B6250S 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4] 5.50" [139.7] 0.75" [19.05] 0.75" [19.05] 4
B6300S 3" [80] 8.00" [203.2] 6.60" [167.6] 8.40" [213.1] 6.00" [152.4] 0.75" [19.05] 0.75" [19.05] 4
B6400S 4" [100] F05 9.00" [228.6] 8.30" [210.8] 9.30" [235.9] 7.50" [190.5] 0.94" [23.88] 0.75" [19.05] 8
B6500S 5" [125] 10.00" [254.0] 10.30" [261.6] 10.50" [266.4] 8.50" [215.9] 0.94" [23.88] 0.88" [22.35] 8
B6600S 6" [150] 11.00" [279.4] 12.50" [317.5] 11.70" [296.9] 9.50" [241.3] 1.00" [25.40] 0.88" [22.35] 8
NOTES:
1) Flange bolt pattern matches ANSI class 125 flanges (not ANSI/ASME rated)
2) Maximum allowable working pressure: 100 PSIG
3) It is not recommended to connect raised-face flanges to flat-faced flanges
13
Characterized Control Valve Product Range Overview
B2.., B3.., 2-way, 3-way, Stainless Steel Ball and Stem
DN 2-way 3-way Non-Spring Spring NEMA

Cv Inches [mm] NPT NPT Return Return 4X
0.3 ½ 15 B207(B) B307(B)

0.46 ½ 15 B208(B) B308(B)
0.8 ½ 15 B209(B) B309(B)
CCV
1.2 ½ 15 B210(B) B310(B)
1.9 ½ 15 B211(B) B311(B)
3 ½ 15 B212(B) B312(B) Equal Percentage
TFR Series
TR Series
Characteristic
4.7 ½ 15 B213(B) B313(B)
7.4 ½ 15 B214(B) Mode of Operation
The Characterized Control Valve is operated by a rotary
10 ½ 15 B215(B) B315(B)
actuator. The actuators are controlled by a standard voltage
14 ½ 15 B216(B)* B316(B)* for on/off control or a proportional signal or 3-point control
system which move the ball of the valve to the position
NR Series
LR Series
LF Series
4.7 ¾ 20 B217(B) B317(B) dictated by the control system.
7.4 ¾ 20 B218(B) B318(B) Product Features
The equal-percentage characteristic of the flow is ensured
10 ¾ 20 B219(B) by the integral characterizing disc. This characteristic
provides linear heating or cooling output from the coil
14 ¾ 20 B220(B)*
improving energy efficiency and comfort.
14 ¾ 20 B320(B)
Actuator Specifications
24 ¾ 20 B221(B)* B321(B)* Control type on/off, floating point, 2-10 VDC,
multi-function technology (MFT)
7.4 1 25 B222 B322 Manual override TR, LR, AR, NR, AFR series
10 1 25 B223 B323 Electrical connection 3 ft [1m] cable with ½”
conduit fitting or covered screw
19 1 25 B224 terminal strip
30 1 25 B225* B325* Valve Specifications
10 1¼ 32 B229 Service chilled or hot water, 60% glycol
19 1¼ 32 B230* B-port modified for constant
common port flow
10 1¼ 32 B329
Controllable flow range 75°

19 1¼ 32 B330 Sizes ½” - 2”
25 1¼ 32 B231 B331 Type of end fitting NPT female ends
Materials
37 1¼ 40 B232* Body forged brass, nickel plated
Ball stainless steel or chrome
19 1½ 40 B238 B338 Stem stainless steel or chrome
29 1½ 40 B239 B339 Seats Teflon® PTFE
Characterizing disc
37 1½ 40 B240* B340 ½”- 1 ½” (2-way) Tefzel®
½”-1” (3-way) Tefzel®
46 1½ 40 B341 2” (2-way) stainless steel
AFR Series
AR Series
AR Series
1¼”- 2” (3-way) stainless steel

29 2 50 B248 B347 Packing 2 EPDM O-rings, lubricated
37 2 50 B348 Media temp range 0°F to 250°F [-18°C to 120°C]
Body pressure rating
46 2 50 B249 B349
½” - 1¼” (B230) 600 psi
57 2 50 B250* B350 1¼”(B231) - 2”(B251) 400 psi
Close-off pressure 200 psi
65 2 50 B251
Maximum differential
68 2 50 B351 pressure (∆P) 50 psi
83 2 50 B352 < 2.0% for B to AB
85 2 50 B252 Cv rating/GPM A port: see product
chart above for values
120 2 50 B253 B port: 70% of A to AB Cv
240 2 50 B254* Tefzel® and Teflon® are registered trademarks of DuPont
* Models without characterizing discs. (B) Models with chrome plated brass ball and brass stem
* 3-Way Valves not for use in change over applications
14
Characterized Control Valve Product Range Overview
B6.., 2-way, Stainless Steel Ball and Stem

DN 2-way Non-Spring Spring Electronic
Cv Inches [mm] NPT Return Return Fail-Safe
70 2½ 65 B6250S-070
AFR
110 2½ 65 B6250S-110
AR
110 3 80 B6300S-110
186 4 100 B6400S-186
CCV
GKR
GR
290 5 125 B6500S-290
Equal Percentage
400 6 150 B6600S-400 Characteristic
Applications
Water-side control of heating and cooling systems for AHU supply,
cooling towers and chillers.
Mode of Operation
The Characterized Control Valve is operated by a rotary actuator. The
actuators are controlled by a standard voltage for on/off control or a
proportional signal or 3-point control system which move the ball of
the valve to the position dictated by the control system.
Product Features
The equal-percentage characteristic of the flow is ensured by the inte-
gral characterizing disc. This characteristic provides linear heating or
cooling output from the coil improving energy efficiency and comfort.
Actuator Specifications
Control type On/Off, Floating Point, 2-10 VDC,
Multi-Function Technology (MFT)
Manual override AR, GR, AFR and GKR series
Electrical connection 3 ft [1m] cable with ½”
conduit fitting or covered screw
terminal strip
Valve Specifications
Service chilled or hot water, 60% glycol
Action max 90° rotation
Sizes 2½”, 3”, 4”, 5:, 6”

Type of end fitting ANSI 125 flange pattern
Materials
Body cast iron (painted)
Seats PTFE
Characterizing disc stainless steel
Body pressure rating According to ANSI 125, standard class B
Media temp range 0°F to 250°F [-18°C to +120°C]
Close-off pressure 100 psi
Maximum differential
pressure (∆P) 50 psi
15
TR24-3 Actuators, On-Off, Floating Point
Dimensions with 2-Way Valve
D1349
D
C
E F B
A TR
Models Valve Nominal Size Dimensions (Inches [mm])

TR24-3-T US Valve Body Inches DN [mm] A B
TR24-3 US TR24-3-T US with 3 ft plenum rated cable
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
TR24-3/300 US TR24-3-T US with 10 ft plenum rated cable
B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
TR24-3/500 US TR24-3-T US with 16 ft plenum rated cable
B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
Technical Data
Control on/off, floating point Dimensions with 3-Way Valve
Nominal voltage 24 VAC 50/60 Hz
D1350
Nominal voltage range 19.2…28.8 VAC
Power consumption 1W
Transformer sizing 1VA (class 2 power source)
Electrical connection screw terminals accessible after removal of
small cover (3 ft, 10 ft, 16 ft cables optional) D C
Input impedance 0.36 kΩ
Angle of rotation 90°
Position indication integrated into handle
Manual override push down handle
Running time 90 seconds @ 60 hz, 108 seconds @ 50 hz

Humidity 5 to 95% non-condensing
E F B
Ambient temperature -22°F to 122°F (-30°C to 50°C)
Storage temperature -40°F to 176°F (-40°C to 80°C) A TFRB, TFRX
Housing NEMA 1/IP40
Housing rating UL94-5V(B)
Agency listing† cULus according to UL 60730-1A/-2-14, CAN/
CSA E60730-1:02, CE according to 2004/108/ Valve Nominal Size Dimensions (Inches [mm])
EC and 2006/95/EC for line voltage and/or –S Valve Body Inches DN [mm] A B C
versions B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Noise level max. 35 db (A) B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Quality standard ISO 9001 B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
† Rated impulse voltage 330V, Control pollution degree 2, Type of action 1
16
TR24-3 Actuators, On-Off, Floating Point
Wiring Diagrams NOTE TR24-3(-T) US cannot be wired in parallel with

NOTE:
themselves or any other actuator.
The common connection from the actuator must be
2
W187
connected to the Hot connection of the controller.
Actuators with plenum rated cable do not have numbers on wires;
3 use color codes instead.
4 The actuator Hot must be connected to the control board Hot.
WARNING Live Electrical Components!

During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualified licensed electrician
or other individual who has been properly trained in handling live electrical components Floating Control
perform these tasks. Failure to follow all electrical safety precautions when exposed to live
W186
electrical components could result in death or serious injury.
On/Off Control
You may not use one wire control.
17
TR24-SR Actuators, Proportional
D1349
D
C
E F B
A TR

TR24-SR-T US Valve Body Inches DN [mm] A B
TR24-SR US TR24-SR-T US with 3 ft plenum rated cable
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
TR24-SR/300 US TR24-SR-T US with 10 ft plenum rated cable
B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
TR24-SR/500 US TR24-SR-T US with 16 ft plenum rated cable
B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
Technical Data
Control proportional Dimensions with 3-Way Valve
Nominal voltage 24 VAC 50/60 Hz, 24 VDC
D1350
Nominal voltage range 19.2…28.8 VAC, 21.6…28.8 VDC
Power consumption 0.5 W
Transformer sizing 1VA (class 2 power source)
Electrical connection screw terminals accessible after removal of
small cover (3 ft, 10 ft, 16 ft cables optional) D C
Input impedance 100 kΩ
Direction of rotation reversible with switch under cover
Position indication integrated into handle
Manual override push down handle

Running time 90 seconds
E F B
Humidity 5 to 95% non-condensing
Ambient temperature -22°F to 122°F (-30°C to 50°C) A TFRB, TFRX
Storage temperature -40°F to 176°F (-40°C to 80°C)
Housing NEMA 1/IP40
Housing rating UL94-5V(B)
Agency listing† cULus according to UL 60730-1A/-2-14, CAN/ Valve Nominal Size Dimensions (Inches [mm])
CSA E60730-1:02, CE according to 2004/108/ Valve Body Inches DN [mm] A B C
EC and 2006/95/EC for line voltage and/or –S B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
versions
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Noise level max. 35 db (A)
B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Quality standard ISO 9001
NOTE: Response sensitivity is 75mV
18
TR24-SR Actuators, Proportional
Wiring Diagrams
W190
Actuators with color coded wires are optional.
2 Wire numbers are provided for reference.
CAUTION Equipment damage!
Actuators may be connected in parallel.
Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.

2 to 10 VDC Control of TR24-SR(-T) US
W191
or other individual who has been properly trained in handling live electrical components
4 to 20 mA Control of TR24-SR(-T) US
Direct/Reverse acting switch is under wiring cover.

R = CW with decrease in signal
L = CCW with decrease in signal
No feedback
19
LR...24-3 Actuators, On/Off, Floating Point
D1351
D C
H1 H2
E F B
A
LRB, LRX -3, -SR
B207(B)-B211(B) ½” 15 1.39” [35.2] 1.39” [35.2]
Models B212(B)-B215(B) ½” 15 1.78” [45.2] 1.78” [45.2]
LRB24-3-T LRX24-3-T w/Terminal Block B217(B)-B221(B) ¾” 20 1.87” [47.4] 1.87” [47.4]
LRB24-3 LRX24-3 w/3 ft. cable B222-B225 1” 25 1.87” [47.4] 1.87” [47.4]
LRB24-3-S LRX24-3-S w/built-in Aux. Switch B229-B231 1¼” 32 1.87” [47.4] 1.87” [47.4]
Technical Data
Control on/off, floating point
D1352
Power supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%
Power consumption running 1.5 W
holding 0.2 W
Transformer sizing 2 VA (class 2 power source) D
Electrical connection ½” conduit connector C
18 GA, plenum rated cable H2
H1
LRB24-3 3 ft [1m]
LRX24-3 3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotation
Input impedance 600 Ω E F B
Angle of rotation 90°, adjustable with mechanical stop A

Direction of rotation reversible with protected switch
LRB, LRX
Position indication handle Valve Nominal Size Dimensions (Inches [mm])
Manual override external push button Valve Body Inches DN [mm] A B C
Running time B307(B)-B311(B) ½” 15 2.06” [52.2] 1.39” [35.2] 1.20” [30.6]
LRB24-3 90 seconds, constant independent of load B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
LRX24-3 150, 95, 60, 45, 35 seconds,
B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
constant independent of load
B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Humidity 5 to 95% RH, non-condensing (EN 60730-1)
Ambient temperature -22°F to 122°F [-30°C to 50°C]
Storage temperature -40°F to 176°F [-40°C to 80°C]
Housing type NEMA 2/IP54
Housing material UL94-5VA
Agency listings† cULus according to UL 60730-1A/-2-14, CAN/
CSA E60730-1:02, CE according to 2004/108/
EC and 2006/95/EC for line voltage and/or –S
versions
Noise level less than 35 dB (A)
LR...24-3-T
Electrical connection screw terminal (for 26 to 14 GA wire)
protected (NEMA 2, IP20)
LR...24-3-S
Auxiliary switch 1 SPDT, 3A (0.5A) @ 250 VAC, UL Listed,
adjustable 0° to 100°
(1.B for -S models)
20
Wiring Diagrams
W193-LR-08
2 CAUTION Equipment damage!
Actuators are provided with color coded wires.

On/Off control
W123-LR-08
Meets cULus or UL and CSA requirements without the
need of an electrical ground connection.

Floating Point or On/Off control
W169-08
Auxiliary switch
21
LR...24-SR Actuators, Proportional
D1351
D C
H1 H2
E F B
A
LRB, LRX -3, -SR
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
LRB24-SR-T LRX24-SR-T w/Terminal Block B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
LRB24-SR LRX24-SR w/3ft. cable B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B231 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
24 VDC ± 10% Dimensions with 3-Way Valve
D1352
holding 0.4 W
Transformer sizing 3 VA (class 2 power source)
Electrical connection ½” conduit connector
18 GA, plenum rated cable D
LRB24-SR 3 ft [1m] C
LRX24-SR 3 ft [1m], 10 ft [3m], 16 ft [5m]
H1 H2
Operating range Y 2 to 10 VDC, 4 to 20 mA
Feedback output U 1 to 10 VDC, max 0.5 mA
Input impedance 100 kΩ (0.1 mA), 500 Ω E F B

LRB, LRX
Running time constant independent of load B307(B)-B311(B) ½” 15 2.06” [52.2] 1.39” [35.2] 1.20” [30.6]
LRB24-SR 90 seconds B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
LRX24-SR 150, 95, 60, 45, 35 seconds B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Humidity 5 to 95% RH non-condensing B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
(EN 60730-1)
Housing NEMA 2/IP54
Agency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to
2004/108/EC and 2006/95/EC for line voltage
and/or –S versions
Noise level <35 dB(A)
LR...24-SR-T
protected (NEMA 2/IP20)
(1.B for -S models)
22
Wiring Diagrams
W265-LR-08
5 Only connect common to neg. (–) leg of control circuits.
2 to 10 VDC control
W265-LR-08
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to 2
to 10 VDC, up to 2 actuators may be connected in parallel.

4 to 20 mA control
23
D1353
D C
H1 H2
E F B
A
LRB, LRX 120-3, MFT, MFT95
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
LRB120-3
B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
LRX120-3
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
Control On/Off, Floating Point
Power supply 100 to 240 VAC, 50/60 Hz (nominal) Dimensions with 3-Way Valve
85 to 265 VAC, 50/60 Hz (tolerance)
D1354
Power consumption running 2 W
holding 0.5 W
Electrical connection ½” conduit connector D
18 GA, plenum rated cable C
LRB120-3 3 ft [1m]
H1 H2
LRX120-3 3 ft [1m], 10 ft [3m], 16 ft [5m]
Input impedance 600 Ω
Angle of rotation 90°, adjustable with mechanical stop E F B
Direction of rotation reversible with protected switch A

Position indication handle
Manual override external push button LRB, LRX
Running time Valve Body Inches DN [mm] A B C
LRB120-3 90 seconds, constant independent of load
B307(B)-B311(B) ½” 15 2.06” [52.2] 1.39” [35.2] 1.20” [30.6]
LRX120-3 150, 95, 60, 45, 35 seconds,
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Humidity 5 to 95% RH non-condensing
(EN 60730-1) B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Housing NEMA 2/IP54
† Rated impulse voltage 4kV, Control pollution degree 3, Type of action 1
24
Wiring Diagrams
W405

On/Off
W406

25
D1353
D C
H1 H2
E F B
A
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
LRB120-SR B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
LRX120-SR B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
Power supply 100 to 240 VAC, 50/60 Hz (nominal)
85 to 265 VAC, 50/60 Hz (tolerance) Dimensions with 3-Way Valve
D1354
holding 1 W
Transformer sizing 4.5 VA (class 2 power source)
LRB120-SR 3 ft [1m] C
LRX120-SR 3 ft [1m], 10 ft [3m], 16 ft [5m] H2
H1
Input impedance 100 kΩ (0.1 mA), 500 Ω E F B

LRB, LRX
Manual override external push button
Running time constant independent of load
B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
LRB120-SR 90 seconds
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
LRX120-SR 150, 95, 60, 45, 35 seconds
B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
(EN 60730-1) B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Housing NEMA 2/IP54
26
WARNING
Live Electrical Components!
During installation, testing, servicing and troubleshooting of this product, it may be
necessary to work with live electrical components. Have a qualified licensed electrician
perform these tasks. Failure to follow all electrical safety precautions when exposed
to live electrical components could result in death or serious injury.
Wiring Diagrams
W365
100 to 240 VAC
15 2 19
N L1 1 Neutral
Cable 2
2 H L2 2 Hot +
6 1 Common
2 Hot +
7 8
Cable 1
7 A 500 Ω resistor converts the 4 to 20 mA control signal to 2 to 10 VDC.
(–)
Control Signal
VDC/mA (+) 3 Y Input, 2 to 10V
15 LRB(X) can be supplied with both 120 VAC and 230 VAC.
2 to 10 VDC (–)
Feedback Signal (+) 5 U Output, 2 to 10V
19 All 120 VAC and 230 VAC actuators use appliance rated cables.
1 0
LR...120-SR

need of an electrical ground connection. Proportional, 100 to 240V
27
LR...24-MFT Actuators, Multi-Function Technology
D1353
D C
H1 H2
E F B
A
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
LRX24-MFT Flexible Version B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
D1354
holding 1.2 W
LRX24-MFT 3 ft [1m], 10 ft [3m], 16 ft [5m] C
H1 H2
Operating range Y 2 to 10 VDC (default)
4 to 20 mA
variable (VDC, PWM, floating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA max E F B
VDC variable A
Input impedance 100 kΩ (0.1 mA), 500 Ω

1500 Ω (PWM, floating point, on/off) LRB, LRX
Angle of rotation 90° electronically variable Valve Nominal Size Dimensions (Inches [mm])
adjustable with mechanical stop Valve Body Inches DN [mm] A B C
Direction of rotation reversible with protected switch B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Position indication handle B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Manual override external push button B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Running time 150 seconds (default) B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Variable (35 to 150 secs)
(EN 60730-1)
Housing NEMA 2/IP54
† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
28
LR...24-MFT Actuators, Multi-Function Technology
Wiring Diagrams
W538

Position feedback cannot be used with Triac sink controller.
4 The actuator internal common reference is not compatible.
Control signal may be pulsed from either the Hot (source)
6 or the Common (sink) 24 VAC line. On/Off control
Contact closures A & B also can be triacs.
W538
8 A& B should both be closed for triac source and open for triac sink.
For triac sink the common connection from the actuator
9 must be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to

2 to 10 VDC, up to 2 actuators may be connected in parallel.

be necessary to work with live electrical components. Have a qualified licensed electrician Floating Point
W538
VDC/4-20 mA
W538
PWM
29
LRX24-PC Actuators, 0 to 20V Phasecut, Proportional
D1353
D C
H1 H2
E F B
A
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
LRX24-PC B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
D1354
holding 1.2 W
Transformer sizing 5 VA (Class 2 power source)
18 GA plenum rated cable
3 ft [1m], 10 ft [3m], 16 ft [5m] D
C
Overload protection electronic throughout 0 to 95° rotation
Operating range Y 0 to 20V phasecut H1 H2
Feedback output U 2 to 10 VDC, 0.5mA max
Input impedance 8 kΩ (50 mW)
Angle of rotation 90°, adjustable with mechanical stop E F B
electronically variable
A
Direction of rotation reversible with switch

Position indication handle LRB, LRX
Manual override external push button Valve Nominal Size Dimensions (Inches [mm])
Running time 150 seconds (default) Valve Body Inches DN [mm] A B C
Humidity 5 to 95% RH non-condensing B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
(EN 60730-1) B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Ambient temperature -22°F to 122°F [-30°C to 50°C] B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Storage temperature -40°F to 176°F [-40°C to 80°C] B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Housing NEMA 2/IP54
30
LRX24-PC Actuators, 0 to 20V Phasecut, Proportional
Wiring Diagrams
W185
1
24 VAC Transformer
Blk (1) Common –

1 Provide overload protection and disconnect as required. Line
Volts Red (2) Hot + 3
2 CAUTION Equipment damage! Pnk (6) Y Input, 0 to 20V phasecut

Actuators may be connected in parallel. Control Signal (–)
Power consumption and input impedance must be observed. 0 to 20 V Phasecut (+)
Org (5) U Output, 2 to 10V
3 Actuators may also be powered by 24 VDC. …PC 2
WARNING Live Electrical Components! LRX24-PC

During installation, testing, servicing and troubleshooting of this product, it may Notes:
or other individual who has been properly trained in handling live electrical components 1 Provide overload protection and disconnect as required.
perform these tasks. Failure to follow all electrical safety precautions when exposed to live Actuators may be connected in parallel. Power
electrical components could result in death or serious injury. 2 consumption and input impedance must be observed.
3 Actuator may also be powered by 24 VDC.

W185
31
LRX24-MFT95 Actuators, 0 to 135 Ω, Proportional
D1353
D C
H1 H2
E F B
A
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
LRX24-MFT95 B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
D1354
holding 1.2 W
3 ft [1m], 10 ft [3m], 16 ft [5m] D
C
Operating range WRB 0 to 135 Ω Honeywell Electronic H1 H2
Series 90, 0 to 135 Ω input
Input impedance 100 kΩ (0.1 mW)
E F B
Angle of rotation 90°, adjustable with mechanical stop
electronically variable A

Direction of rotation reversible with switch LRB, LRX
Running time 150 seconds (default) B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
variable (35 to 150 seconds) B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Humidity 5 to 95% RH non-condensing B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
(EN 60730-1) B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Housing NEMA 2/IP54
†Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3.
32
24 Resistor value depends on the type of 23 Volts
22 Actuators and controller must have 22
controller and the number of
Wht (3) W Wiring Multiple Actuato
separate transformers. actuators.
W No resistor is used for one 24 22
24 VAC Transformer
Series 90 actuator.
R Honeywell® resistor
Wht kits
(4) may
R 21
B
Controller
also be used.
23 Consult controller instruction data for B R W B Wht (5) B Line H205
LRX24-MFT95 Actuators, 0 to 135 Ω, Proportional

Changeover W
more detailed information. 25 To reverse control rotation,Wht
use Volts
(6)the‘U5’ Output 2 to 10 VDC
Controller
reversing
Series 90 high switch.
limit control - 280 Ω -MFT95 US
24 Resistor value depends on the type of Shunting
W
controller and the number of Override

Resistor 22 R
Wiring Multiple Actuators to a Series 90 Controller B W
Wiring Diagrams actuators. No resistor is used for one 24 Shunting
W_new60408_5
Switch A Switch B Damper Position Resistor
Series 90
24 VAC Transformer
actuator. Honeywell® resistor kits may ControllerB
W018
21 Damper Open
also be used. Line Blk (1)Closed
Damper Common
21
Y
Line
Volts Red (2) GMX24-MFT95
+ Hot
25 To reverse control rotation, use the Actuators:
The AF24-MFT95
direction of rotation switch is set so that the failUS
safe position and the Volts
23 AMX24
R
21 Provide overload protection and disconnect as required. position of the damper is closed with no signal at wire R.
24
reversing switch. W973, W7100
W
21 24 VAC Transformer Wht (3) W 25actuators
No. of Controller
Resistance
Shunting
Actuators and controller must have separate transformers.
W015
R Wht (4) R 2 140 Ω
22 Override
Resistor
Line Blk (1) Common 3 71.5 Ω
Volts B Red (2)Wht (5) B
+ Hot High45 Limit47.5 Ω
Control
24 23 Output 2 to 10 VDC6
37.5 21
Ω
Consult controller instruction data for more detailed
Switch A Switch B Damper Position INSTALLATION
Series 90 A NOTES
Wht (6) ‘U5’ 28 Ω To oth
23 information. Controller Wht (3) W Line actua
Resistor Kit No. ZG-R03
24 24 VAC Transformer
Damper Open 135 Ω Wht (4) R
-MFT95 US 21 Volts
2121 Provide overload B Wiring Multiple Actuato
protection
Wht (5) Band using
Line a Minimum Posit
Resistor value depends on the type of controller and the Damper Closed
Line disconnect as required.
Wht (6)Blk‘U5’(1)
Output 2 toCommon
10 VDC Volts
24 number of actuators. No resistor is used for one actuator. 24 VAC Transformer
The direction of rotation switch is set so that the fail safe position and the Volts 24 VAC Transformer Red (2)US + Hot
-MFT95 No. of
22
21 Actuators and controller must have 21
23 22 W actuators R
Honeywell® resistor kits may also be used.
position of the damper is closed with no signal at wire R.
separate transformers. Line 2
Line Blk (1) Common Series 90 3
Volts R
No. of
Volts Red (2)Wht (3) W
+ Hot 25Controller 4
To reverse control rotation, use the reversing 23 Consult controller instruction
actuators Resistance data
Wht (4) R 23for Series 90 B R W
W015
Controller Resistor Kit N
140 Ω
25 Line
2
more detailed information.
A R B W
switch.2524232221 Blk (1) Common 3
Line
71.5 Ω W Wht (3)Wht
W (5) B 24
Series
B
90 high limit control -2
4 47.5 Ω R R
Volts Red (2) + Hot 24
Volts
5 Resistor
37.5 Ω value dependsB
Wht on
(4) the
Wht (6)type
R
‘U5’ of
Output 2 to 10 VDC 22
23 6 controller
28 Ω B and the number of
Wht (5) B Shunting
Resistor
W
Wiring Multiple Actuat
WARNING Live Electrical Components! A
Wht (3) W
22 Kitactuators.
Resistor No. ZG-R03 No
Controller
To other
resistorWht
actuators is(6)
used for
-MFT95
‘U5’ Output 2 toone
10 VDC US
24 23
During installation, testing, servicing and troubleshooting Override
24 actuator. Honeywell® resistor -MFT95 US kits may 21B
24 VAC Transformer
R W
135 Ω Wht (4) R also be used.
Wiring Multiple Actuators to a Series 90 Controller
of this product, it may be necessary to work with live electri- B Line
H205 Change- Occupied
cal components. Have a qualified licensed electrician or other Wht (5) B using a Minimum
Low Limit Control Position Potentiometer over Controller Contact
Volts
Wht (6) ‘U5’ Output 2 to 10 VDC 25 To reverse control rotation, use the 21 24 V
individual who has been properly trained in handling live electrical S963A
reversing switch. Minimum Position
W016
W019
components perform these tasks. Failure to follow all electrical -MFT95 US 24
24 VAC Transformer
VAC Transformer Potentiometer W
2121 Line
safety precautions when exposed to live electrical components 21 24 VAC Transformer Shunting
21
Resistor R
Override
Line
Line Blk (1)BlkCommon Volts
could result in death or serious injury. Line (1) Common Line B
Blk (1) Common Volts Red (2) + Hot 24
VoltsSwitch A Switch B Damper Position
Red (2) + Hot Volts 23
Series 90 22
Volts Red (2) + Hot 23
Series 90 25 Controller
23 22 W
Controller
Damper Open
Wht (3) W 22 24
W
A
W R B 24 21
SeriesB90 R B W (4)Wht
WhtDamper R (3) W R
Wht (3) W R Closed
Line
W 24 Controller Line
B Wht (5)Wht B (4) R B
Wht (4) R R Volts
Volts
R 22
The direction of rotation switch is set so that the fail safe position and the Shunting
Resistor
B position of the damper is closed with no signal atWht
WSeries 90 low limit control
wire(6)Wht
R. (5)
‘U5’ Output 2 B
to 10 VDC
B Wht (5) B Shunting
Resistor 135 Ω for 0 to 50% control
W973, W7100
T775 T
24280 Ω forTransformer
VAC 0 to 100% control Wht (6)US‘U5’ Output 2 to 10 VDC
-MFT95 No. of a
22 Controller Wht (6) ‘U5’ Output 2 to 10 VDC 21 23 actuators Resistance
24
W015
-MFT95 US 2 140 Ω
Line Blk (1) Common
-MFT95 US B R W
3 71.5 Ω
Volts 4 47.5 Ω
Red (2) + Hot 5 37.5 Ω
H205 Change- Occupied 23 6 28 Ω
A
over Controller Contact To ot
Low Limit Control Wht (3) W 24
Resistor Kit No. ZG-R03 actua
135 Ω Wht (4) R Wiring Multiple Actuat

W016
B
Wht (5) B using a Minimum Posi
24 VAC Transformer
21 Wht (6) ‘U5’ Output 2 to 10 VDC
21
21 -MFT95 US 24 VAC Transformer
Line Blk (1) Common 21 24 VAC Transformer 21 Line
Line Blk (1) Common
Volts Red (2) + Hot Line Volts
Line Blk (1) Common

23 Volts Red (2) + Hot Volts
Volts Red (2) + Hot 23 Series 90
23 22
22 W W R B Wht (3) W 24 22 A
Controller
R B W
Series 90 W Wht (3) Wht
W (3) 24
W 25 B
R Wht (4) R Line
R
Controller R Wht (4) Wht
R (4) R 22
Volts B
B Wht (5) B Wht (5) Wht
B (5) Shunting W
B B
Wiring multiple
actuators to Controller
a
Resistor
Wht (6) ‘U5’ 22

Output 2 to 10 VDC Wht (6) ‘U5’ Output 2 to 10 VDC 23
Series 90 low limit control Wht (6) ‘U5’ Output 2 to 1024
VDC
135 Ω for 0 to 50% control Series 90 controller using a To other -MFT95 US
280 Ω for 0 to 100% control -MFT95 US -MFT95 US
B R W
minimum position potentiometer actuators
over Controller Contact
Low Limit Control
24 VAC Transformer W016

21
21
Line Blk (1) Common
Line
Volts Red (2) + Hot
23 Volts
22 W W R B Wht (3) W 24 22
Series 90 Wht (4) R
R
Controller
Actuators: AF24-MFT95 US GMX24-MFT95B AMX24-MFT95
Wht (5) NMX24-MFT95
B LMX24-MFT
Series 90 low limit control Wht (6) ‘U5’ Output 2 to 10 VDC
135 Ω for 0 to 50% control T
280 Ω for 0 to 100% control -MFT95 US a
Low Limit ControlHigh Limit Control Typical wiring diagram

INSTALLATION NOTES used with the W973, W
W017
24 VAC Transformer
21
21 24 VAC Transforme
21 Provide overload protection and Line Blk (1) Common
disconnect as required. Volts Red (2) + Hot Line
23 Volts
22 Actuators and controller must have 22 Wht (3) W
W 24
separate transformers. Series 90 Wht (4) R
22 B R W
R
Controller
23 Consult controller instruction data for B R W B Wht (5) B H205
Changeover W R B
more detailed information. Wht (6) ‘U5’ Output 2 to 10 VDC
Controller
Series 90 high limit control - 280 Ω

-MFT95 US
24 Resistor value depends on the type of
HighofLimit Control
controller and the number Wiring Multiple Actuators to a Series 90 Controller
22
W
actuators. No resistor is used for one Shunting
Resistor
24 VAC Transformer
actuator. Honeywell® resistor kits may B
W018
21
also be used. Line Blk (1) Common Y
800-543-9038 USA 866-805-7089 CANADA Volts 203-791-8396 LATIN AMERICA / CARIBBEAN
Red (2) + Hot
25 To reverse control rotation, use the 23 R R W
24
reversing switch.
W Wht (3) W 25 W973, W7100
Controller
33
Shunting
Resistor R Wht (4) R
LRQ...24-1 Quick Running Actuators, On/Off
D1355
D C
H1 H2
E F B
A
LRQB, LRQX
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
LRQB24-1 Basic Version B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
LRQX24-1 Flexible Version B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
Control on/off Dimensions with 3-Way Valve
D1356
24 VDC ± 10%
holding 1.5 W
20A @ 5ms max D
Electrical connection ½” conduit connector C
18 GA plenum rated cable H2
H1
LRQB24-1 3 ft [1m]
LRQX24-1 3 ft [1m], 10 ft [3m], 16 ft [5m]
Input impedance 600 Ω E F B
Angle of rotation max 95°, adjustable with mechanical stop A

Position indication handle LRQB, LRQX
Running time
B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
LRQB24-1 5 seconds
B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
constant of independent load
LRQX24-1 5 or 10 seconds B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
constant of independent load B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
(EN 60730-1)
Housing NEMA 2/IP54
34
LRQ...24-1 Quick Running Actuators, On/Off
Wiring Diagrams
W403-LRQ-08
1 Provide overload protection and disconnect as required.

LRQ...24-1
35
LRQ...24-MFT Quick Running Actuators, Multi-Function Technology
D1371
D C
H1 H2
E F B
A
LRQB, LRQX
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
LRQB24-MFT Basic Version B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
LRQX24-MFT Flexible Version B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
24 VDC ± 10%
D1372
holding 1.5 W
20A @ 5ms max
Electrical connection ½” conduit connector D
18 GA plenum rated cable C
LRQB24-MFT 3 ft [1m] H2
H1
LRQX24-MFT 3 ft [1m], 10 ft [3m], 16 ft [5m]
Operating range Y 2 to 10 VDC, 4 to 20 mA (default)
variable (VDC, on/off) E F B
Feedback output U 2 to 10 VDC, 0.5mA max A

VDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω LRQB, LRQX
1500 Ω (on/off) Valve Nominal Size Dimensions (Inches [mm])
Angle of rotation max 95°, adjustable with mechanical stop Valve Body Inches DN [mm] A B C
Direction of rotation reversible with switch B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Position indication reflective visual indicator (snap-on) B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Manual override external push button B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Running time B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
LRQB24-MFT 5 seconds
LRQX24-MFT 5 or 10 seconds
(EN 60730-1)
Housing NEMA 2/IP54
36
LRQ...24-MFT Quick Running Actuators, Multi-Function Technology
Wiring Diagrams
W399_08
2

5 or the Common (sink) 24 VAC line.
VDC/4-20 mA
W399_08
The ZG-R01 500 Ω resistor may be used.

On/Off control
37
NRQ...24-1 Quick Running Actuators, On/Off
D1357
D C
H1 H2
E F B
A
NRQB, NRQX
B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
Models
NRQB24-1 Basic Version B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
NRQX24-1 Flexible Version B248-B250 2” 50 4.21” [107] 2.27” [57.7]
Technical Data Dimensions with 3-Way Valve

Control on/off
D1358
24 VDC ± 10%
holding 1.5 W
D
Transformer sizing 18 VA (Class 2 power source) C
Electrical connection ½” conduit connector,
18 GA plenum rated cable H1 H2
NRQB24-1 3 ft [1m]
NRQX24-1 3 ft [1m], 10 ft [3m], 16 ft [5m]
E F B
Angle of rotation max 95°, adjustable with mechanical stop A
Direction of rotation reversible with switch NRQB, NRQX

Position indication reflective visual indicator (snap-on)
Running time constant of independent load B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
NRQB24-1 5 seconds
NRQX24-1 5, 10 or 15 seconds
(EN 60730-1)
Housing NEMA 2/IP54
Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3.
38
NRQ...24-1 Quick Running Actuators, On/Off
Wiring Diagrams
W403-NRQ-08

NRQ...24-1
39
NRQ...24-MFT Quick Running Actuators, Multi-Function Technology
D1357
D C
H1 H2
E F B
A
NRQB, NRQX
B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
Models B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
NRQB24-MFT Basic Version B248-B250 2” 50 4.21” [107] 2.27” [57.7]
NRQX24-MFT Flexible Version

Technical Data
D1358
24 VDC ± 10%
holding 1.5 W
Transformer sizing 18 VA (Class 2 power source) D
C
NRQB24-MFT 3 ft [1m]
NRQX24-MFT 3 ft [1m], 10 ft [3m], 16 ft [5m]
Operating range Y 2 to 10 VDC, 4 to 20 mA (default) E F B
variable (VDC, on/off) A
Feedback output U 2 to 10 VDC, 0.5mA max NRQB, NRQX
VDC variable Valve Nominal Size Dimensions (Inches [mm])

Input impedance 100 kΩ (0.1 mA), 500 Ω, 1500 Ω Valve Body Inches DN [mm] A B C
(on/off) B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Angle of rotation max 95°, adjustable with mechanical stop
Position indication reflective visual indicator (snap-on)
Running time constant of independent load
NRQB24-MFT 5 seconds
NRQX24-MFT 5, 10 or 15 seconds
(EN 60730-1)
Housing NEMA 2/IP54
40
NRQ...24-MFT Quick Running Actuators, Multi-Function Technology
Wiring Diagrams
W399_08
2

VDC/4-20 mA
W399_08

On/Off control
41
NRB24-3-T N4, NRX24-3-T N4 NEMA 4X Actuators, On/Off, Floating Point
D1363
D C
E F B
A
ARB N4, ARX N4, NRB N4, NRX N4
Models B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
NRB24-3-T N4 B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
NRB24-3-T N4H w/built in heater B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
NRX24-3-T N4
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
NRX24-3-T N4H w/built in heater
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
Control on/off, floating point Dimensions with 3-Way Valve
D1364
24 VDC ± 10%
Power consumption running 2.0 W / heater 24 W
holding 0.2 W
Transformer sizing 4 VA (class 2 power source) / heater 19 VA
Electrical connection screw terminal (for 26 to 14 GA wire) D C
Position indication visual pointer E F B

Manual override external push button A
Running time 90 seconds constant independent of load NRB N4, NRX N4
Humidity 100% RH Valve Nominal Size Dimensions (Inches [mm])
Ambient temperature -22°F to 122°F [-30°C to 50°C] Valve Body Inches DN [mm] A B C
Storage temperature -40°F to 176°F [-40°C to 80°C] B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Housing type UL Type 4X/NEMA 4X/IP66 & IP67 B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Housing material Polypropylene B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Agency listings† cULus according to UL 60730-1A/-2-14, B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
CAN/CSA E60730-1, CSA C22.2 No. 24-93,
CE according to 89/336/EEC.
*Cannot be used with the CCV-EXT-KIT
† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1.
42
NRB24-3-T N4, NRX24-3-T N4 NEMA 4X Actuators, On/Off, Floating Point
Wiring Diagrams
W193-NR-08
Actuators may be connected in parallel. N
Actuators are provided with color coded wires. 1

On/Off control
W123-NR-08
WARNING Live Electrical Components! N L L N L

be necessary to work with live electrical components. Have a qualified licensed electrician 1 2 3
electrical components could result in death or serious injury. N
1
T
Floating Point control H
(°C)
M
m with actuator types ..-3
Legend:
1
N L L N L M = actuator
2 T (°C) = Thermostat
1 2 3 H = Heating
N L L N L
T H
1 2 3 (°C) S1 S2 S3 S4 S5 S6
M
T
1 <x <x
>x >x
2 1 2
T H x = 0 ... 100%
(°C)
Note
M
1 The ffollowing points must be taken into account
N L L N L
with independent, external wiring:
2
• All contact between the cables or wires that
1 2 3 S1 S2 isS3
are introduced and the heating element to beS4 S5 S6
avoided.
• Where necessary, use cables with sufficient
<x
T numbers of wires, e.g. so that the heating and the <x
N L N L >x
actuator can be supplied separately with voltage.
>x
T H x = 0 ... 100%
(°C)
1 2 3 5 1 2
Heater wiring
M
1
2
T H
(°C)
M T 1
N L N L
2
1 2 3 5 1 2
T H
(°C)
M
1
2
43
NRB24-SR-T N4, NRX24-SR-T N4 NEMA 4X Actuators, Proportional
D1363
D C
E F B
A
Models B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
NRB24-SR-T N4 B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
NRB24-SR-T N4H w/built in heater B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
NRX24-SR-T N4 B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
NRX24-SR-T N4H w/built in heater B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data Dimensions with 3-Way Valve1363

Control 2 to 10 VDC, 4 to 20 mA
D1364
24 VDC ± 10%
holding 0.4 W
Transformer sizing 5 VA (class 2 power source) / heater 20 VA C
D
Input impedance 100 kΩ (0.1mA), 500Ω
Direction of rotation reversible with switch E F B
Position indication visual pointer A

Manual override external push button NRB N4, NRX N4
Running time 90 seconds constant independent of load Valve Nominal Size Dimensions (Inches [mm])
Humidity 100% RH Valve Body Inches DN [mm] A B C
Ambient temperature -22°F to 122°F [-30°C to 50°C] B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Storage temperature -40°F to 176°F [-40°C to 80°C] B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Housing type UL Type 4X/NEMA 4X/IP66 & IP67 B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Housing material Polypropelene B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
CAN/CSA E60730-1, CSA C22.2 No. 24-93,
†Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3
44
NRB24-SR-T N4, NRX24-SR-T N4 NEMA 4X Actuators, Proportional
Wiring Diagrams
W265-NR-08
2 CAUTION Equipment damage! N L L N L
Power consumption and input impedance must be observed. 1 2 3

T H
(°C)
2 to 10 VDC control
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to 2 M
to 10 VDC, up to 2 actuators may be connected in parallel. 1
W265-NR-08
2
N L L N WARNING
L Live Electrical Components!
1 2 3 be necessary to work with live electrical components. Have a qualified licensed electrician
perform these tasks. Failure to follow all electrical safety precautions when exposed to live N L L N L
1 2 3 S1 S2 S3 S4 S5 S6
T H
Wiring Diagrams (°C)
<x <x
M
Legend: >x >x
1
N L L N L M = actuator T H x = 0 ... 100%
4 to 20 mA control
2 T (°C) = Thermostat (°C)
1 2 3 H = Heating
M
1
2
N L L N L
T H
1 2 3 (°C) S1 S2 S3 S4 S5 S6
M
T
N L N L
1 <x <x
>x >x
2 1 2 3 5 1 2
T H x = 0 ... 100%
(°C)
Note
M
N L L N L T H
2 (°C)
1 2 3 S1 S2 isS3
avoided. M
• Where necessary, use cables with sufficient 1
<x
T numbers of wires, e.g. so that the heating and the <x 2
N L N L >x
>x
T H x = 0 ... 100%
(°C)
1 2 3 5 1 2
Heater wiring
M
1
2
T H
(°C)
M T 1
N L N L
2
1 2 3 5 1 2
T H
(°C)
M
1
2
45
NRX24-MFT-T N4 NEMA 4X Actuators, Multi-Function Technology
D1363
D C
E F B
A
Models B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
NRX24-MFT-T N4 B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
NRX24-MFT-T N4H w/built in heater B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
Technical Data B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Control 2 to 10 VDC, 4 to 20 mA (default)
Dimensions with 3-Way Valve1363
D1364
24 VDC ± 10%
Power consumption running 3.5 W (1.25 W) / heater 24 W
holding 1.25 W
Overload protection electronic throughout 0° to 95° rotation D C
Input impedance 100 kΩ (0.1 mA), 500 Ω
1500 Ω (PWM, floating point, on/off)
Direction of rotation reversible with switch E F B

Position indication visual pointer A
Manual override external push button NRB N4, NRX N4
Running time 150 seconds (default) Valve Nominal Size Dimensions (Inches [mm])
constant independent of load Valve Body Inches DN [mm] A B C
variable (75 to 350 seconds) B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Humidity 100% RH B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Ambient temperature -22°F to 122°F [-30°C to 50°C] B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Storage temperature -40°F to 176°F [-40°C to 80°C] B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Housing type UL Type 4X/NEMA 4X/IP66 & IP67
Housing material Polypropelene
Agency Listings† cULus according to UL 60730-1A/-2-14, CAN/
CSA E60730-1, CSA C22.2 No. 24-93, CE ac-
cording to 89/336/EEC.
46
NRX24-MFT-T N4 NEMA 4X Actuators, Multi-Function Technology
Wiring Diagrams
W538

N L L N L
Control signal may be pulsed from either the Hot (source) On/Off control
1 2 3
W538
T H
(°C)
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to M

2 to 10 VDC, up to 2 actuators may be connected in parallel. 1
2
N L L N WARNING
1 2 3 be necessary to work with live electrical components. Have a qualified licensed electrician Floating Point
W538
1 2 3 S1 S2 S3 S4 S5 S6
T H
(°C)
<x <x
M
Legend: >x >x
1
1 2 3 H = Heating
M
VDC/4-20 mA 1
2
N L L N L
W538
T H
1 2 3 (°C) S1 S2 S3 S4 S5 S6
M
T
N L N L
1 <x <x
>x >x
2 1 2 3 5 1 2
T H x = 0 ... 100%
(°C)
Note
M
N L L N L T H
2 PWM (°C)
1 2 3 S1 S2 isS3
avoided. M
<x
N L N L >x
>x
T H x = 0 ... 100%
(°C)
1 2 3 5 1 2
Heater wiring
M
1
2
T H
(°C)
M T 1
N L N L
2
1 2 3 5 1 2
T H
(°C)
M
1 47
2
AR...24-3 Actuators, On/Off, Floating Point
D1359
D C
H1 H2
E F B
A
ARB, ARX
B231-B232 1¼” 32 3.72” [94.6] 1.98” [50.4]
B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
Models B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
ARB24-3 B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
ARB24-3-S w/built-in Aux. Switch B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
ARX24-3 Flexible B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
ARX24-3-S Flexible w/built-in Aux. Switch
ARB24-3-5-14
ARX24-3-5-14 Dimensions with 3-Way Valve
D1360
Technical Data
24 VDC ± 10% D C
holding 0.2 W H1 H2
18 GA plenum rated cable E F B
ARB24-3... 3 ft. [1m] A

ARX24-3... 3 ft. [1m] 10 ft. [3m] 16 ft. [5m]
Overload protection electronic throughout 0° to 95° rotation ARB, ARX
Input impedance 600 Ω Valve Body Inches DN [mm] A B C
Angle of rotation 90°, adjustable with mechanical stop B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
Direction of rotation reversible with protected switch B338-B341 1½” 40 4.39” [111.6] 2.45” [62.2] 2.33” [59.1]
Position indication handle B347-B352 2” 50 4.90” [124.5] 2.68” [68.0] 2.60” [66.0]
Running time
ARB24-3... 90 seconds
ARX24-3... 300, 150, 90 seconds,
Humidity 5 to 95% RH non-condensing (EN 60730-1)
Housing NEMA 2/IP54
AR...24-3-S
Auxiliary switch (-S models) 1 x SPDT, 3A (0.5A) @ 250 VAC, UL Listed,
adjustable 0 to 90°
(1.B for -S models)
48
Dimensions Wiring Diagrams
D1373
D Actuators may be connected in parallel.
I Power consumption and input impedance must be observed.
C For end position indication, interlock control, etc.,
3 ARB24-3-S incorporates one built-in auxiliary switches:
1 x SPDT, 3A (0.5A) @250 VAC, UL listed, adjustable 0° to 95°.
G
B
E F A Meets cULus or UL and CSA requirements without the
need of an
On-off electrical
control ground connection.
of ARB24-3
ARB, ARX
Nominal Top During installation, testing, servicing and troubleshooting of this product, it may
Valve Flange Face-to-Face be necessary to work with live electrical components. Have a qualified licensed electrician
Pipe Flange Height
Body Diameter Length or other individual who has been properly trained in handling live electrical components
Size Design
A B C electrical components could result in death or serious injury.
B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4]
WARNING
B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1] Live Electrical Components!
During installation, testing, servicing and troubleshooting of this product, it maybe
B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9] or other individual who has been properly trained in handling live electrical components
Floating pointperform
or on-off control
these tasks. Failure of ARB24-3
to follow all electrical safety precautions when exposed
W409
24 VAC Transformer 2
4
Line Blk (1) Common –
Volts Red (2) +
a open a
Wht (3) +
a closed
The indication of direction

WARNING
1 0
is valid for switch position 1.
During installation, testing, servicing and troubleshooting of this product,ARB24-3
it maybe
On/Off control
W411
4

Volts Red (2) +
Notes:
Wht (3) +
The indication
2 Actuators may alsoof direction
be powered by 24 VDC.
1 0

Auxiliary switch of ARB24-3-S ARB24-3
Meets cULus requirements without the
4 need of an electrical ground connection.
W410
Notes:
WARNING
During installation, testing, servicing and S1 3
2 Actuators
troubleshooting mayit maybe
of this product, also be powered by 24
NC
VDC.
necessary to work with live electrical
components. Have a qualified licensed S2
Meets cULus requirements without the need of an
4 or other individual who has been
electrician
electrical
properly trained in handlingground connection. S3
live electrical 0° to 95°
NO
components perform these tasks. Failure to
follow all electrical safety precautions when
exposed to live electrical components could ARB24-3-S W409
result in death or serious injury.
Auxiliary switch
Notes:
800-543-9038 USA 866-805-7089 CANADA 1 203-791-8396

Provide overload LATIN
protection and AMERICA
disconnect / CARIBBEAN
as required.
W411
2 Actuators may also be powered by 24 VDC. 49
For end position indication, interlock control,
AR...24-SR Actuators, Proportional
D1359
D C
H1 H2
E F B
A
ARB, ARX
B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
Models
ARB24-SR
ARX24-SR Flexible Version Dimensions with 3-Way Valve
D1360
Technical Data
24 VDC ± 10%
Power consumption running 2.5 W C
D
holding 0.4 W
Transformer sizing 5 VA (class 2 power source) H1 H2
3 ft [1m], 10 ft [3m], 16 ft [5m]
E F B
A
Feedback output U 1 to 10 VDC, max 0.5 mA ARB, ARX
Input impedance 100 kΩ (0.1 mA), 500 Ω Valve Nominal Size Dimensions (Inches [mm])
Angle of rotation 90°, adjustable with mechanical stop Valve Body Inches DN [mm] A B C

Torque 180 in-lb [20 Nm] B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Running time
ARB24-SR... 90 seconds
ARX24-SR... 300, 150, 90 seconds,
(EN 60730-1)
Ambient temperature -22°F to +122°F [-30°C to +50°C]
Storage temperature -40°F to +176°F [-40°C to +80°C]
Housing NEMA 2/IP54
(1.B for -S models)
50
AR...24-SR
WARNING
Actuators, Proportional
Wiring Diagrams
W408
Blk (1) Common –

2 CAUTION Equipment damage! Line
Power consumption and input impedance must be observed. Wht (3) Y Input, 2 to 10V
Control Signal (–)
3 Actuators may also be powered by 24 VDC. 2 to 10 VDC (+)
1 0
2 to 10 VDC (–)
WARNING WARNING
Feedback Signal (+)
ARB24-SR
During installation, testing, servicing and troubleshooting of this product, it maybe During installation, testing, servicing and troubleshooting of this product, it maybe
necessary to work with live electrical components. Have a qualified licensed electrician necessary to work with live electrical components. Have a qualified licensed electrician
2 to 10 VDC control
to live electrical components could result in death or serious injury. to live electrical components could result in death or serious injury.
W408
2 to 10 VDC, up to 2 actuators may be connected
24 VACinTransformer
parallel. 2 24 VAC Transformer 2

Line Blk (1) Common – Line Blk (1) Common –
During installation, testing, servicing and troubleshooting
Volts of this product, it may Red (2) Hot + 3 Volts Red (2) Hot + 3
be necessary to work with live electrical components. Have a qualified licensed electrician Ω
Wht (3) Y Input, 2 to 10V
Control Signal (–) 4 to 20 mA (–) 500Ω
perform these tasks. Failure to follow all electrical safety precautions (+)when exposed to live Org (5) U Output, 2 to 10V Control Signal (+) Wht (3) Y Input, 2 to 10V
2 to 10 VDC
electrical components could result in death or serious injury. 1 0 Org (5) U Output, 2 to 10V
2 to 10 VDC (–)
Feedback Signal (+) ARB24-SR 1 0
5 To other ARB24-SR
actuators
Notes:
4 to 20 mA control 1 Provide overload protection and d
Actuators may be connected in pa
2 consumption and input impedanc
3 Actuator may also be powered by
The ZG-R01 500Ω resistor conve
4 control signal to 2 to 10 VDC, up
be connected in parallel.
5 Only connect common to neg. (–)
Notes:

Actuators may be connected in parallel. Power

2 consumption and input impedance must be observed.
The ZG-R01 500Ω resistor converts the 4 to 20 mA
4 control signal to 2 to 10 VDC, up to 2 actuators may
be connected in parallel.
W408
51
D1361
D C
H1 H2
E F B
A
ARB, ARX 120-3, 120-SR, MFT

B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
Models B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
ARB120-3 B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
ARX120-3 Flexible Version B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]

D1362
Power supply 100 to 240 VAC, 50/60 Hz (nominal)
holding 0.6 W
D C
Electrical connection ½” conduit connector H1 H2
18 GA appliance rated cable
ARB120-3 3 ft [1m]
ARX120-3 3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotation E F B
A

Angle of rotation 90°, adjustable with mechanical stop ARB, ARX
Direction of rotation reversible with protected switch Valve Nominal Size Dimensions (Inches [mm])
Position indication handle Valve Body Inches DN [mm] A B C
Manual override external push button B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Running time B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
ARB120-3 90 seconds B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
ARX120-3 300, 150, 90 seconds,
(EN 60730-1)
Housing NEMA 2/IP54
Servicing maintenance free
52
Dimensions Wiring Diagrams
D1373
D
I
C Actuators may be connected in parallel.
G Meets cULus or UL and CSA requirements without the

B
E F A WARNING Live Electrical Components!
ARB, ARX be necessary to work with live electrical components. Have a qualified licensed electrician
Nominal Top electrical components could result in death or serious injury.
Valve Flange Face-to-Face
Pipe Flange Height
Body Diameter Length
Size Design
A B C
W414
B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4]
B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1]
B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9]
On/Off control
W415
53
AR...120-SR Actuators
D1361
D C
H1 H2
E F B
A

B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
Models
ARB120-SR Dimensions with 3-Way Valve
ARX120-SR Flexible Version
D1362
Technical Data
Power supply 100 to 240 VAC, 50/60 Hz (nominal) D C
Power consumption running 3 W H1 H2
holding 0.6 W
Electrical connection ½” conduit connector E F B
18 GA plenum rated cable A
ARB120-SR 3 ft [1m]
ARX120-SR 3 ft [1m], 10 ft [3m], 16 ft [5m] ARB, ARX
B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]

B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
Running time
ARB120-SR 90 seconds
ARX120-SR 300, 150, 90 seconds,
(EN 60730-1)
Housing NEMA 2/IP54
54
WARNING
AR...120-SR Actuators
Wiring Diagrams
W365
100 to 240 VAC
15 2 19
N L1 1 Neutral
Cable 2
2 H L2 2 Hot +
6 1 Common
2 Hot +
7 8
Cable 1
7 A 500 Ω resistor converts the 4 to 20 mA control signal to 2 to 10 VDC.
(–)
Control Signal
VDC/mA (+) 3 Y Input, 2 to 10V
15 ARB(X) can be supplied with both 120 VAC and 230 VAC.
2 to 10 VDC (–)
Feedback Signal (+) 5 U Output, 2 to 10V
19 All 120 VAC and 230 VAC actuators use appliance rated cables.
1 0

need of an electrical ground connection. Proportional, 100 to 240V

55
AR...24-MFT Actuators, Multi-Function Technology
D1361
D C
H1 H2
E F B
A

B231-B232 1¼” 32 3.72” [94.6] 1.98” [50.4]
B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
Models B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
ARX24-MFT
B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
ARX24-MFT-5-14
D1362
24 VDC ± 10%
holding 1.25 W
Transformer sizing 6 VA (class 2 power source) D C
ARX24-MFT 3 ft. [1m], 10 ft. [3m], 16 ft. [5m]
Operating range Y 2 to 10 VDC, 4 to 20 mA (default) E F B
variable (VDC, PWM, floating point, on/off) A
Feedback output U 2 to 10 VDC, 0.5 mA max

VDC variable ARB, ARX
Input impedance 100 kΩ (0.1 mA), 500 Ω Valve Nominal Size Dimensions (Inches [mm])
1500 Ω (PWM, floating point, on/off) Valve Body Inches DN [mm] A B C
Angle of rotation 95° electronically variable B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
Running time
ARB24-MFT 150 seconds
ARX24-MFT variable (90 to 350 seconds)
(EN 60730-1)
Housing NEMA 2/IP54
CAN/CSA E60730-1:02, CE according
to 2004/108/EC and 2006/95/EC for line
voltage and/or –S versions
56
AR...24-MFT Actuators, Multi-Function Technology
Dimensions
W538
D1374
D
I
C
G On/Off control
W538
B
E F A
ARB, ARX
Nominal Top
Pipe Flange Height
Size Design
A B C
B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4]
Floating Point
B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1]
W538
B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9]
Wiring Diagrams

VDC/4-20 mA
W538
4
The actuator internal common reference is not compatible.

6
or the Common (sink) 24 VAC line.
8
A& B should both be closed for triac source and open for triac sink.
9
must be connected to the hot connection.
PWM

During installation, testing, servicing and troubleshooting of this
product, it may be necessary to work with live electrical components. Have a
qualified licensed electrician or other individual who has been properly trained
in handling live electrical components perform these tasks. Failure to follow all
electrical safety precautions when exposed to live electrical components could
57
ARX24-PC Actuators, Phasecut
D1361
D C
H1 H2
E F B
A

B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
Models B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
ARX24-PC B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]

D1362
24 VDC ± 10%
holding 1.25 W
Transformer sizing 5.5 VA (Class 2 power source)
Electrical connection ½” conduit connector D C
3 ft. [1m], 10 ft. [3m], 16 ft. [5m] H1 H2
Operating range Y 0 to 20V phasecut
Feedback output U 2 to 10 VDC, 0.5mA max E F B
VDC variable A
Input impedance 8 kΩ (50 mW)
ARB, ARX

Angle of rotation 90°, adjustable with mechanical stop Valve Nominal Size Dimensions (Inches [mm])
electronically variable Valve Body Inches DN [mm] A B C
Direction of rotation reversible with switch B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Position indication handle B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
Manual override external push button B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
Running time 150 seconds (default)
(EN 60730-1)
Housing NEMA 2/IP54
†Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3.
58
ARX24-PC Actuators, Phasecut
Wiring Diagrams
W185
1
24 VAC Transformer
Blk (1) Common –

1 Provide overload protection and disconnect as required. Line
2 CAUTION Equipment damage! Pnk (6) Y Input, 0 to 20V phasecut

Actuators may be connected in parallel. Control Signal (–)
Power consumption and input impedance must be observed. 0 to 20 V Phasecut (+)
3 Actuators may also be powered by 24 VDC. …PC 2
WARNING Live Electrical Components! 0 to 20V Phase Cut

During installation, testing, servicing and troubleshooting of this product, it may Notes:
or other individual who has been properly trained in handling live electrical components 1 Provide overload protection and disconnect as required.
perform these tasks. Failure to follow all electrical safety precautions when exposed to live Actuators may be connected in parallel. Power
electrical components could result in death or serious injury. 2 consumption and input impedance must be observed.

W185
59
ARX24-MFT95 Actuators, 0 to 135 Ω
D1361
D C
H1 H2
E F B
A

B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
Models B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
ARX24-MFT95

D1362
24 VDC ± 10%
holding 1.25 W
Transformer sizing 6 VA (Class 2 power source) D C
3 ft [1m], 10 ft [3m], 16 ft [5m]
Operating range WRB 0 to 135 Ω Honeywell Electronic E F B
Series 90, 0 to 135 Ω input A
Input impedance 100 kΩ (0.1 mW) ARB, ARX

electronically variable Valve Body Inches DN [mm] A B C
Direction of rotation reversible with switch B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Position indication handle B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
Manual override external push button B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
variable (90 to 350 seconds)
(EN 60730-1)
Housing NEMA 2/IP54
†Rated Impulse Voltage 800V, Type of action 1.AA, Control Pollution Degree 3.
60
ARX24-MFT95 Actuators, 0 to 135 Ω
S963A
24 VAC Minimum Pos
Transformer Potentiome
1
Wiring Diagrams Switch A Switch B Damper Position
Line
Damper Open
Volts
Damper Closed Series 90
Controller
The direction of rotation switch is set so that the fail safe position and the
B R B W
1 Provide overload protection and disconnect as required. R

2
24 VAC Transformer W
1 Shunting
Resistor
2 CAUTION Equipment damage! Line

Volts
1 Common
2 + Hot 3
4
3
Actuators and controller must have separate transformers. A 4

B R W
3 W H205 Change- Occupied

Consult controller instruction data for more detailed installation over Controller Contact
3 135 4 R
B
information. 5 B
Resistor value depends on the type of controller and the number of

6 ‘U5’ Output 2-10 VDC
…MFT95 1
4 actuators. No resistor is used for one actuator. Honeywell resistor 1
24 VAC Transformer
Line
kits may also be used. Line 1 Common Volts
Volts 2 + Hot 3
2
5 To reverse control rotation, use the reversing switch. A 4
W 3 W
Line R 4 R

Volts B
B 5 B
2 6 ‘U5’ Output 2-10 VDC
During installation, testing, servicing and troubleshooting of this product, it may Controller
To other
…MFT95
be necessary to work with live electrical components. Have a qualified licensed electrician actuators
perform these tasks. Failure to follow all electrical safety precautions when exposed to live Override Wiring multiple actuato
Series 90 controller usi
minimum position pote
S963A
24 VAC Minimum Position
Transformer Potentiometer
1
Switch A Switch B Damper Position
Line
Notes: 1 Common Line
Damper Open
Volts 2 + Hot Volts
Damper Closed Series 90
1
Controller
Provide overload protection and
5
disconnect as required.
R B W 2
B 3 W W W B R
R
2 Actuators and controller
4 R must have separate transformers
Series 90 R
2
24 VAC Transformer 5 B Controller
W B
1 Shunting
Resistor
1 Common 3 Series 90 low limit contro
3 Consult controller instruction data for more135detailed
Line
4 for 0 to 50% control
Volts 2 + Hot 3 …MFT95 280 for 0 to 100% control
B R Winstallation information.
A 4
3 W
over Controller Contact Low Limit Contro
135 4 R
B
5 B
24 VAC Transformer
1 1
24 VAC Transformer …MFT95
1 Line 1 Common Line
3
Line 1 Common Volts 2 + Hot Volts
Volts 2 + Hot 3 5
2
4 2
A 3 W W
W 3 W
Line 4 R Series 90 R
R 4 R
Volts B 5 B Controller R W B
B
B 5 B
2 Controller 6 ‘U5’ Output 2-10 VDC 6 ‘U5’ Output 2-10 VDC
To other Series 90 high limit control - 2
…MFT95 actuators …MFT95
Override Wiring multiple actuators to a High Limit Control

Series 90 controller using a
minimum position potentiometer.
Notes:
S963A
24 VAC Minimum Position
Potentiometer
1
Transformer
1 Provide overload protection and disconnect
1
24 VACas required.
Transformer 4 Resistor value depends on the
Line 1 Common 1 Common
the number of actuators. No r
Line
Damper Open
Volts 2 Actuators and controller
2 + Hot must have Volts
separate transformers. 2 + Hot actuator.
3 Honeywell resistor k
Damper Closed Series 90 5
Controller 5
R B W 2
B
Consult controller
3 W
instruction data for more Rdetailed
W W B R 3 W
5 To reverse control rotation, use
R 3 4 R
Series 90
4 R
2
24 VAC Transformer W
installation information.
5 B Controller
B 5 B
1 Shunting
Resistor
6 ‘U5’ Output 2-10 VDC 6 ‘U5’ Output 2-10 VDC
Line 1 Common 3 Series 90 low limit control
4 135 for 0 to 50% control
Volts 2 + Hot 3 …MFT95 280 for 0 to 100% control …MFT95
B R W
A 4
3 W
over Controller Contact Low Limit Control
135 4 R
B
5 B
24 VAC Transformer
1 1
24 VAC Transformer …MFT95
1 Line 1 Common Line 1 Common
3
Line 1 Common Volts 2 + Hot Volts 2 + Hot 3
Volts 2 + Hot 3 5
2 5
4 2
A 3 W W 3 W
W 3 W
Line 4 R R 4 R
R 4 R Series 90
Volts B 5 B Controller R W B 5 B
B 5 B B
2 Controller 6 ‘U5’ Output 2-10 VDC 6 ‘U5’ Output 2-10 VDC 6 ‘U5’ Output 2-10 VDC
To other Series 90 high limit control - 280
…MFT95 actuators …MFT95 …MFT95
Override Wiring multiple actuators to a High Limit Control

Series 90 controller using a
minimum position potentiometer.

Notes:
61
1 Provide overload protection and disconnect as required. 4 Resistor value depends on the type of controller and
ARB24-3-T N4, ARX24-3-T N4 NEMA 4X Actuators, On/Off, Floating Point
D1363
D C
E F B
A
Models B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
ARB24-3-T N4 B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
ARB24-3-T N4H w/built in heater B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
ARX24-3-T N4 B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
ARX24-3-T N4H w/built in heater B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
Technical Data
D1364
24 VDC ± 10%
holding 0.5 W
Transformer sizing 5.5 VA (class 2 power source) / heater 20.5 VA
Position indication visual pointer

Manual override external push button E F B
A
Running time 90 seconds constant independent of load
Humidity 100% RH NRB N4, NRX N4
Ambient temperature -22°F to 122°F [-30°C to 50°C] Valve Nominal Size Dimensions (Inches [mm])
Storage temperature -40°F to 176°F [-40°C to 80°C] Valve Body Inches DN [mm] A B C
Housing type UL Type 4X/NEMA 4X/IP66 & IP67 B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Housing material Polypropelene B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
Agency listings† cULus according to UL 60730-1A/-2-14, B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
CAN/CSA E60730-1, CSA C22.2 No. 24-93,
62
ARB24-3-T N4, ARX24-3-T N4 NEMA 4X Actuators,
WARNING
On/Off, Floating Point Live Electrical Components!
Floating pointperform
or on-offthese tasks. Failure to follow all electrical safety precautions when exposed
control of ARB24-3
Wiring Diagrams
W409
4
2 CAUTION Equipment damage! Volts Red (2) +

Power consumption and input impedance must be observed. a open a
Wht (3) +
a closed N
For end position indication, interlock control, etc.,
3 ARB24-3-S incorporates one built-in auxiliary switches: 1
The indication of direction 1 0
1 x SPDT, 3A (0.5A) @250 VAC, UL listed, adjustable 0° to 95°. is validWARNING
for switch position 1.
Live Electrical Components! ARB24-3
4 Actuators may also be powered by 24 VDC. During installation, testing, servicing and troubleshooting of this product, it maybe
On/Off control or other individual who has been properly trained in handling live electrical components
W411
Meets cULus or UL and CSA requirements without the 24 VAC Transformer 2
4
WARNING Live Electrical Components! Volts Red (2) +

During installation, testing, servicing and troubleshooting of this product, it may N L L N L Notes:
1 Provide overload protection and Wht
disconnect
(3) + as required.
or other individual who has been properly trained in handling live electrical components 1 2 3
electrical components could result in death or serious injury. 2 Actuators may also
The indication be powered by1240 VDC.
of direction
N
Meets cULus requirements without the ARB24-3
4 need of an electrical ground connection.
1
T H
Floating Point or On/Off
(°C) control
M
Notes: Legend:
1
N L L N L M = actuator
2 T (°C) = Thermostat
1 2 3 2 Actuators may also be powered byH24
= Heating
VDC.

4
electrical ground connection.
N L L N L W409
T H
1 2 3 (°C) S1 S2 S3 S4 S5 S6
M
T
1 <x <x
>x >x
2
x = 0 ... 100% 1 2
T H
(°C)
Note
M
N L L N L
2
1 2 3 S1 S2 isS3
are introduced and the heating element
W411
to beS4 S5 S6
avoided.
<x
N L N L >x
>x
T H x = 0 ... 100%
(°C)
1 2 3 5 1 2
Heater wiring
M
1
2
T H
(°C)
M T 1
N L N L
2
1 2 3 5 1 2
T H
(°C)
M
1
2
63
ARB24-SR-T N4, ARX24-SR-T N4 NEMA 4X Actuators, Proportional
D1363
D C
E F B
A
Models B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
ARB24-SR-T N4 B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
ARB24-SR-T N4H w/built in heater B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
ARX24-SR-T N4 B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
ARX24-SR-T N4H w/built in heater B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
Technical Data
Power supply 24 VAC ± 20% 50/60 Hz Dimensions with 3-Way Valve1363
24 VDC ± 10%
D1364
holding 0.4 W
Electrical connection screw terminal (for 26 tp 14 GA wire)
Position indication visual pointer E F B

Manual override external push button A
Running time 90 seconds constant independent of load NRB N4, NRX N4
Humidity 100% RH Valve Nominal Size Dimensions (Inches [mm])
Ambient temperature -22°F to 122°F [-30°C to 50°C] Valve Body Inches DN [mm] A B C
Storage temperature -40°F to 176°F [-40°C to 80°C] B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Housing type UL Type 4X/NEMA 4X/IP66 & IP67 B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
Housing material Polypropelene B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
CAN/CSA E60730-1, CSA C22.2 No. 24-93,
64
N L L N L
1 2 3
ARB24-SR-T N4, ARX24-SR-T N4 NEMA 4X Actuators, Proportional
N
1
Wiring Diagrams Wiring Diagrams(°C)T H
M
Legend:
1
2 CAUTION Equipment damage! N L L N L M = actuator
Actuators may be connected in parallel. 2 T (°C) = Thermostat
Power consumption and input impedance must be observed. 1 2 3 H = Heating
Only connect common to neg. (–) leg of control circuits. N L L N L

5
T H
1 2 3 (°C) S1 S2 S3 S4 S5 S6

T
M
1 <x <x
2 to 10 VDC, up to 2 actuators may be connected in parallel. >x >x
2 1 2
T H x = 0 ... 100%
WARNING Live Electrical Components! (°C)
be necessary to work with live electrical components. Have a qualified licensed electrician Note
or other individual who has been properly trained in handling live electrical components M
electrical components could result in death or serious injury. 2
1 2 3 S1 S2 isS3
avoided.
<x
N L N L >x
>x
T H x = 0 ... 100%
(°C)
1 2 3 5 1 2
Heater wiring
M
1
W408-SR-T
2
T H
(°C)
M T 1
N L N L
2
1 2 3 5 1 2
2 to 10 VDC control
T H
W408-SR-T
(°C)
M
1
2
4 to 20 mA control
65
ARX24-MFT-T N4 NEMA 4X Actuators, Multi-Function Technology
D1363
D C
E F B
A
B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
Models
ARX24-MFT-T N4 B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
ARX24-MFT-T N4H w/built in heater B248-B250 2” 50 4.21” [107.0] 2.27” [57.7]
B251-B254 2” 50 4.93” [125.2] 2.73” [69.5]
B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
Technical Data B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
Power supply 24 VAC ± 20% 50/60 Hz Dimensions with 3-Way Valve1363
24 VDC ± 10%
D1364
holding 1.25 W
Electrical connection screw terminal (for 26 tp 14 GA wire)
D C
Input impedance 100 kΩ for 2 to 10 VDC (0.1 mA)
500 Ω for 4 to 20 mA
1500 Ω for PWM, floating point and
on/off control
E F B

A
Position indication visual pointer NRB N4, NRX N4
Manual override external push button Valve Nominal Size Dimensions (Inches [mm])
Running time 150 seconds (default) Valve Body Inches DN [mm] A B C
constant independent of load B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
variable (75 to 350 seconds) B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
Humidity 100% RH B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
Housing type UL Type 4X/NEMA 4X/IP66 & IP67
Housing material Polypropelene
CSA E60730-1, CSA C22.2 No. 24-93, CE ac-
cording to 89/336/EEC.
66
ARX24-MFT-T N4 NEMA 4X Actuators, Multi-Function Technology
Wiring Diagrams
W538

Control signal may be pulsed from either the Hot (source) N L L N L
6 On/Off control
1 2 3
W538
T H
(°C)
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to M

2 to 10 VDC, up to 2 actuators may be connected in parallel. 1
2
N L L N WARNING
1 2 3 be necessary to work with live electrical components. Have a qualified licensed electrician Floating Point
W538
1 2 3 S1 S2 S3 S4 S5 S6
T H
(°C)
<x <x
M
Legend: >x >x
1
1 2 3 H = Heating
M
VDC/4-20 mA 1
2
W538
N L L N L
T H
1 2 3 (°C) S1 S2 S3 S4 S5 S6
M
T
N L N L
1 <x <x
>x >x
2 1 2 3 5 1 2
T H x = 0 ... 100%
(°C)
Note
M
N L L N L T H
2 PWM (°C)
1 2 3 S1 S2 isS3
avoided. M
<x
N L N L >x
>x
T H x = 0 ... 100%
(°C)
1 2 3 5 1 2
Heater wiring
M
1
2
T H
(°C)
M T 1
N L N L
2
1 2 3 5 1 2
T H
(°C)
M
1 67
ARQX24-1 Quick Running Actuators, On/Off
D1375
D C
H1 H2
E F B
A
ARQB, ARQX
B248-B280 2” 50 4.21” [107] 2.27” [57.7]
Models
ARQX24-1 Flexible Version Dimensions with 3-Way Valve
D1376
Technical Data
Control on/off
24 VDC ± 10% D
C
holding 1.5 W H1 H2
3 ft [1m], 10 ft [3m], 16 ft [5m] E F B
Overload protection electronic throughout 0 to 95° rotation A
Input impedance 100 Ω ARQB, ARQX
Angle of rotation max 95°, adjustable with mechanical stop Valve Nominal Size Dimensions (Inches [mm])
Direction of rotation reversible with switch Valve Body Inches DN [mm] A B C
Position indication reflective visual indicator (snap-on) B330-B332 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
Manual override external push button B338-B340 1½” 40 4.39” [111.6] 2.51” [63.7] 2.90” [61.1]

Running time constant of independent load B348-B352 2” 50 4.95” [124.5] 2.73” [69.5] 2.74” [69.7]
10 or 15 seconds
(EN 60730-1)
Housing NEMA 2/IP54
68
ARQ...24-1
ARQX24-1 Quick Running Actuators, On/Off
Wiring Diagrams
W403-ARQ-08
ARQ...24-1
ARQX24-1
W403-ARQ-08
69
ARQX24-MFT Quick Running Actuators, Multi-Function Technology
D149-2A
B231-B232 1¼” 32 3.72” [94.6] 2.04” [51.9]
Models B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
ARQX24-MFT Flexible Version B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
Technical Data
B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
24 VDC ± 10%
Power consumption running 15 W Dimensions with 3-Way Valve
holding 1.5 W
D149A
3 ft [1m], 10 ft [3m], 16 ft [5m]
Operating range Y 2 to 10 VDC, 4 to 20 mA (default)
variable (VDC, on/off)
VDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω, 1500 Ω
(on/off)

Angle of rotation max 95°, adjustable with mechanical stop
Position indication reflective visual indicator (snap-on) Valve Nominal Size Dimensions (Inches [mm])
Running time constant of independent load B330-B332 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
10 or 15 seconds B338-B340 1½” 40 4.39” [111.6] 2.51” [63.7] 2.90” [61.1]
Humidity 5 to 95% RH non-condensing B348-B352 2” 50 4.95” [124.5] 2.73” [69.5] 2.74” [69.7]
(EN 60730-1)
Housing NEMA 2/IP54
70
ARQX24-MFT Quick Running Actuators, Multi-Function Technology
Wiring Diagrams
W399_08
2

VDC/4-20 mA
W399_08

On/Off control
71
GRB24-3, GRX24-3 Actuators, On/Off, Floating Point
Dimensions
D1377
D
I C
B
E F A
GRB, GRX
Nominal Top
Pipe Flange Height
Models Body
Size Design
Diameter Length
GRB24-3-5-14
GRX24-3-5-14 A B C
B6400 4” [100] 9.00” [228.6] 8.30” [210.8] 9.30” [235.9]
B6500 5" [125] 10.00" [254] 10.30" [261.6] 10.50" [266.4]
Technical Data F05
B6600 6" [150] 11.00" [279.4] 12.50" [317.5] 11.70" [296.9]
holding 2 W
Electrical connection 3 ft,18 GA plenum rated cable
½” conduit connector
GRX 3 ft. [1m], 10 ft. [3m], 16 ft. [5m]
Angle of rotation max. 95°, adjustable with mechanical stop

Position indication visual indicator
Running time 150 seconds, constant independent of load
Housing NEMA 2/IP54, Enclosure Type 2
Agency listings † cULus according to UL 60730-1A/-2-14,
2004/108/EEC and 2006/95/EC.
† Rated Impulse Voltage 800V, Type of action 1.AA (1.AA.B for -S version), Control Pollution Degree 3.
72
GRB24-3, GRX24-3 Actuators, On/Off, Floating Point
Wiring Diagrams
W254_08
Meets cULus requirements without the need of an electrical ground

connection.

be necessary to work with live electrical components. Have a qualified licensed electrician On/Off control
W255_08

73
GRB120-3, GRX120-3
Dimensions
D1377
D
I C
B
E F A
GRB, GRX
Nominal Top
Pipe Flange Height
Models Body
Size Design
Diameter Length
GRB120-3
GRX120-3 A B C
B6400 4” [100] 9.00” [228.6] 8.30” [210.8] 9.30” [235.9]
B6500 5" [125] 10.00" [254] 10.30" [261.6] 10.50" [266.4]
Technical Data F05
B6600 6" [150] 11.00" [279.4] 12.50" [317.5] 11.70" [296.9]
Power Supply 100 to 240 VAC, 50/60 Hz (nominal)
holding 2 W
Electrical connection 18 GA appliance rated cable
3 ft. [1m], 10 ft. [3m], 16 ft. [5m]

Position indication external push button
Running time 150 seconds, constant independent of load
Humidity 5 to 95% RH non condensing (EN 60730-1)
2004/108/EEC and 2006/95/EC.
74
GRB120-3, GRX120-3
Wiring Diagrams
W375_08
2 Power consumption and input impedance must be observed.

connection.

On/Off control
W376_08

75
GRX24-MFT Actuators, Multi-Function Technology
Dimensions
D1377
D
I C
B
E F A
GRB, GRX
Nominal Top
Pipe Flange Height
Size Design
Models A B C
GRX24-MFT-5-14 B6400 4” [100] 9.00” [228.6] 8.30” [210.8] 9.30” [235.9]
B6500 5" [125] 10.00" [254] 10.30" [261.6] 10.50" [266.4]
Technical Data F05
B6600 6" [150] 11.00" [279.4] 12.50" [317.5] 11.70" [296.9]
24 VDC ± 10%
holding 1.5 W
3 ft. [1m], 10 ft. [3m], 16 ft. [5m]

Feedback output 2 to 10 VDC, 0.5 mA max, VDC variable
Input impedance 100 kΩ (0.1 mA, 500 Ω)
1500 Ω (PWM, floating point , on/off)
Housing material UL94-5V (flammability rating)
2004/108/EEC and 2006/95/EC.
76
GRX24-MFT Actuators, Multi-Function Technology
Wiring Diagrams
W399_08
2 CAUTION Equipment Damage!

Actuators may be connected in parallel if not mechanically mount-
ed to the same shaft. Power consumption and input impedance
must be observed.

Control signal may be pulsed from either the Hot (source) VDC/4-20 mA
W399_08
8 A & B should both be closed for triac source and open for triac sink.
9 must be connected to the hot connection of the controller.
Meets UL requirements without the need of an electrical ground

connection.
WARNING Live Electrical Components! PWM

W399_08
On/Off control
W399_08
Floating Point control
77
TFRB(X) Actuators, On/Off
D1365
D C
E F
B
A
TFRB, TFRX
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
Models
TFRB(X)24 TFRB(X)120
TFRB(X)24-S TFRB(X)120-S w/built-in Aux. Switch
Technical Data
D1366
Control on/off
Power supply
TFRB(X)24(-S) 24VAC ± 20%, 50/60Hz
24VDC ± 10%
TFRB(X)120(-S) (nominal) 100 to 240 VAC, 50/60 Hz D
(tolerance) 85 to 265 VAC, 50/60 Hz C
holding 1.3 W
Transformer sizing
TFRB(X)24(-S) 5 VA (class 2 power source) E F B
TFRB(X)120(-S) 5 VA (class 2 power source) A
Electrical connection ½” conduit connector TFRB, TFRX
(-S models have 2 cables) 18 GA appliance cable Valve Nominal Size Dimensions (Inches [mm])

TFRB(X)24... 3 ft [1m]
TFRB(X)120 10 ft [3m]
B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
16 ft [5m]
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Direction of rotation reversible with protected mounting
Position indication visual indicator, 0° to 95°
Running time motor <75 seconds (0 to 18 in-lb)
spring <75 sec @ -22°F to 122°F [-20°C to 50°C]
Housing NEMA type 2/IP42
Housing material UL94 - 5VA
versions
Noise level (max) running <40 db (A)
spring return <40 dB (A)
TFRB(X)...-S
Auxiliary switch 1 x SPDT, 3A (0.5A) @ 250 VAC, UL Listed
† Rated impulse voltage 800V (4kV for 120V model), Control pollution degree 3,
Type of action 1.AA (1.AA.B for -S models)
78
TFRB(X)
WARNING
Actuators, On/Off
Wiring Diagrams On-off wiring for TFX120 US
W237
24 VAC Transformer
1 Common
2 + Hot 3
Actuators may be connected in parallel. WARNING
TFX24 US 2
Power consumption and input impedance must be observed. Live Electrical Components!
3 Actuators may also be powered by 24 VDC. On/Off Wiring or other individual who has been properly trained in handling live electrical components
W217
100 to 240 VAC
Meets cULus or UL and CSA requirements without the N L1 1 Neutral
need of an electrical ground connection. 1 Provide
H L2 2 Hot as required.
overload protection and disconnect
WARNING Live Electrical Components! 2

Actuators may be connected in parallel. Power consumption
must be observed. TFX120 US 2
be necessary to work with live electrical components. Have a qualified licensed electrician Auxiliary switch
3 Actuator may of TFX…-S
also US by 24VDC.
be powered
or other individual who has been properly trained in handling live electrical components On/Off Wiring
W248
WARNING
1 Components!
Live Electrical
Provide overload protection and disconnect as required.
During installation, testing, servicing and S1
troubleshooting Actuators may
of this product, be connected in parallel. Power
it maybe
necessary2to work with live electrical
consumption must be observed.
NC
electrician or other individual who has been
Meets cULus requirements without S3 the need0°oftoan95°
3 electrical
properly trained in handling live electrical
ground connection. NO
exposed to live electrical components could TFX…-S US 2
Auxiliary Switch
W237
Actuators may be connected in parallel. Power

2 consumption must be observed.
Meets cULus requirements without the need of anW217
3 electrical ground connection.
W248
79
TFRB(X)24-3 Actuators, Floating Point
D1365
D C
E F
B
A
TFRB, TFRX
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
Models
TFRB(X)24-3
TFRB(X)24-3-S w/built-in Aux. Switch
D1366
Technical Data
Control floating point
Power supply 24VAC ± 20%, 50/60Hz
holding 1.0 W D
Transformer sizing 4 VA (class 2 power source) C
(-S models have 2 cables) 18 GA plenum rated cable
TFRB(X)24-3... 3 ft [1m]
10 ft [3m]
E F B
16 ft [5m]
A
TFRB, TFRX
Input impedance 1000 Ω (0.6w) control inputs

Direction of rotation spring reversible with CW/CCW mounting
B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
motor reversible with built-in switch
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Running time motor 95 sec constant, independent of load
<60 sec @ -22°F [-30°C]
versions
spring return 62 dB (A)
TFRB(X)24-3-S US
Auxiliary switch 1 x SPDT, 3A (0.5A) @ 250 VAC, UL Listed,
80
Floating point control of TF24-3 (-S) US
TFRB(X)24-3 Actuators, Floating Point

WARNING
Wiring Diagrams
W240
Line Blk (1) Common
2 CAUTION Equipment damage! Volts Red (2) ~

Actuators may be connected in parallel. a Wht (W3) ~
Triac source Installation Side
xx
xx
xx
xx
xx
xx
~
xx
xx
xx
xx
Or (W4)
xx xx
The common connection from the actuator must be

xx xx
b
xx xx
xx xx
x x
CCW CW
3 connected to the Hot connection of the controller.
Switch
Positions
a b
Direction of Rotation Switch
(3) (4) CW CCW CW CCW

TF24-3 (-S) US
4 The actuator Hot must be connected to the control board common. stop stop stop stop
For end position indication, interlock control, fan startup, etc., The indication of direction is valid
for switch position CW.
5 TF24-3-S US incorporates one built-in auxiliary switch: 1 x SPDT, 3A
(0.5A) @250 VAC, UL listed, adjustable 0° to 95°. Floating point control
Actuators with plenum rated cable do not have numbers on wires; use
7
W242
color coded instead. Actuators with appliance rated cable use numbers. 24 VAC Transformer
WARNING Line
Live Electrical Components! Volts
During installation, testing,
servicing and troubleshooting
Meets cULus or UL and CSA requirements without the of this product, it maybe
2 7
need of an electrical ground connection. necessary to work with live
electrical components.Notes:
Have
Hot Com
a qualified licensed electrician
Blk (1) Common
WARNING Live Electrical Components! or other individual who has
been properly trained in 1 Provide overload protection and disconnect as required. Red (2) Hot ~
During installation, testing, servicing and troubleshooting of this product, it mayhandling live electrical
Triac Wht (W3) ~
components perform these sink
be necessary to work with live electrical components. Have a qualified licensed electrician tasks. Failure to follow all2 Actuators may be connected in parallel. Power consumption
Or must
(W4) be observed. ~
or other individual who has been properly trained in handling live electrical componentselectrical safety precautions
when exposed to live electrical
components could result in
death or serious injury. 7
Actuators with plenum rated cable do not have numbers on wires;TF24-3
use (-S)
color
US codes instead.
Controller The indication of direction
is valid for switch position CW.
Triac source
W243
24 VAC Transformer
WARNING Line
Live Electrical Components! Volts
2 7
of this product, it maybe W240
necessary to work with live
electrical components. Have
Hot Com
Blk (1) Common
or other individual who has
been properly trained in
Red (2) ~ Hot 3
handling live electrical
components perform these Notes: Wht (W3) ~ 4
tasks. Failure to follow all
Or (W4) ~
electrical safety precautions

components could result in 1 Provide overload protection and disconnect as required.
TF24-3 (-S) US
death or serious injury.
Controller
2 The indication of direction is valid for switch position CW.
must be observed.
Auxiliary switch of TF24-3 (-S) US
Triac sinkActuators
with separate transformers
with plenum rated cable do not have numbers on wires; use color code
7
W241
WARNING
During installation, testing, servicing and S1 5
troubleshooting of this product, it maybe
NC
S3
NO W242
0° to 95°
Notes: components perform these tasks. Failure to
exposed to live electrical components could TF24-3-S US
Auxiliary switch
2 must be observed.
The Common connection from

For end the actuator
position must
indication, be connected
interlock to startup,
control, fan the etc.,
3 5 the
Hot connection of controller.
TF24-3 (-S) US, TF120-S US and TF230-S US incorporates
one built-in auxiliary switch: 1 x SPDT,
4 6A (1.5A)
The actuator Hot must @250 VAC,
be connected ULcontrol
to the listed, adjustable 0° to 95°.
board Common.
6 Meets cULus requirements without the need of an
7 Actuators with plenum rated cable do not have numbers on wires; use color codes inst
W243
81
TFRB(X)24-SR Actuators, Proportional
D1365
D C
E F
B
A
TFRB, TFRX
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
B217(B)-B221(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
Models
TFRB(X)24-SR
TFRB(X)24-SR-S w/built-in Aux. Switch
D1366
Technical Data
Control proportional
Power supply 24 VAC ± 20%, 50/60 Hz
24 VDC ± 10%
Power consumption running 2.5 W D
holding 1.0 W C
(-S models have 2 cables) 18 GA plenum rated cable
TFRB(X)24-SR... 3 ft [1m]
10 ft [3m] E F B
16 ft [5m] A
Electrical protection actuators are double insulated TFRB, TFRX
Overload protection electronic throughout 0° to 95° rotation Valve Nominal Size Dimensions (Inches [mm])

Operating range Y 2 to 10 VDC, 4 to 20 mA Valve Body Inches DN [mm] A B C
Input impedance 100k Ω (0.1mA), 500 Ω B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Feedback Output U 2-10 VDC B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Angle of rotation 95° B317(B)-B321(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Running time motor 95 sec constant, independent of load
spring <25 sec @-4°F to 122°F [-20°C to 50°C]
<60 sec @-22°F [-30°C]
versions
TFRB(X)24-SR-S
82
TFRB(X)24-SR
WARNING
Wiring Diagrams
W245
mA control of TF24-SR (-S) US withBlk

4 to 20 Line 2 to(1)
10 Common
VDC feedback output
2 CAUTION Equipment damage! Volts Red (2) + Hot
3
Actuators may be connected in parallel. Wht (3) Y1 Input, 2 to 10V
Power consumption and input impedance must be observed. Control Signal (–)
2 to 10 VDC (+)
Up to 4 actuators may be connected in parallel. With 4 actuators wired
4 to one 500 Ω resistor, a +2% shift of control signal may be required. WARNING 2
Power consumption must be observed. Live Electrical Components! TF24-SR US
3 Actuators may also be powered by 24 VDC. or other individual who has been properly trained in handling live electrical components
2 to 10 VDC control perform these tasks. Failure to follow all electrical safety precautions when exposed
5 Only connect common to neg. (—) leg of control circuits.
W246
Actuators with plenum rated cable do not have numbers on wires;
6 use color codes instead. Notes:
Line Blk (1) Common
3
For end position indication, interlock control, fan startup, etc., Volts Red (2) + Hot
1 Provide overload Ωprotection and disconnect as required.
7 TF24-SR-S US incorporates one built-in auxiliary switch: 1 x SPDT, 3A
4 to 20 mA (–) 500Ω
(0.5A ) @250 VAC, UL listed, adjustable 0° to 95°. Actuators may be connected in
2 Signal (+)
Control
parallel. Power consumption
Wht (3) Y1 Input, 2 to 10V
and input impedance must be observed.
4
Auxiliary switches of TF24-SR-S US
Meets cULus or UL and CSA requirements without the 5 2
To other
Actuators with actuators
plenum rated cable do not have numbers on
need of an electrical ground connection. 6 TF24-SR US
wires; use color codes instead.
WARNING Live Electrical Components! 4 to 20 mA control

W246
perform these tasks. Failure to follow all electrical safety precautions when exposed to live WARNING
electrical components could result in death or serious injury. Live Electrical Components!
Notes:During installation, testing, servicing and S1 7
necessary to work with live electrical NC
1 Provide overload
components. protection
Have a qualified licensed S2 as required.
and disconnect
Up totrained
properly 4 actuators
in handling may be connected in S3
live electrical parallel.
NO
0° to 95°
With
2 4 actuators
follow all electrical wired to one 500Ω
safety precautions when resistor, a +2% shift of
controlto live
exposed signal may
electrical be required.
components could TF24-SR-S US
Power consumption
must
result be observed.
in death or serious injury. W245
Auxiliary switch3 Actuator may also be powered by 24 VDC.
A 500Ω resistor converts the 4… 20mA control
4 signal to 2 to 10 VDC. (ZG-R01)
For end position indication, interlock control, fan startup, etc.,
5 Only connect common toUS
7 TF24-SR-S neg. (–) leg of control
incorporates circuits.
one built-in auxiliary switch: 1 x
6A (1.5A) @250 VAC, UL listed, adjustable 0° to 95°.

6 Actuators with plenum rated cable do not have numbers
on wires; use color codes instead.
W247
W246
83
TFRX24-MFT Actuators, Multi-Function Technology
D1365
D C
E F
B
A
TFRB, TFRX
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
B217-B221 ¾” 20 2.73” [69.3] 1.87” [47.4]
Models
TFRX24-MFT
Technical Data
D1366
Control MFT
24 VDC ± 10%
holding 1.0 W D
Transformer sizing 4 VA (class 2 power source) C
3 ft [1m], 18 GA plenum rated cable
Operating range Y* 2 to 10 VDC, 4 to 20 mA (default)
variable (VDC, PWM, floating point, on/off) E F B
Feedback output U* 2 to 10 VDC, 0.5 mA max A
Input impedance 100 kΩ for 2 to 10 VDC (0.1 mA) TFRB, TFRX

1500 Ω for PWM, floating point and Valve Body Inches DN [mm] A B C
on/off control B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Mechanical angle of rotation* 95° B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Angle of rotation adaptation* Off (Default) B317-B321 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Override control* Min. (Min Position) = 0%
- ZS (Mid. Position) = 50%
- Max. (Max. Position) = 100%
Running time motor* 95 seconds constant independent of load
spring <25 seconds @-4°F to 122°F [-20°C to 50°C]
<60 seconds @-22°F [-30°C]
Humidity 5 to 95% RH, non-condensing
Ambient temperature -22 to 122° F (-30 to 50° C)
Storage temperature -40 to 176° F (-40 to 80° C)
Housing NEMA 2/IP42
Housing material UL 94-5VA
versions
Noise level (max) running <35 dB (A)
* Variable when configured with MFT options
† Rated impulse voltage 0.8 kV, Control pollution degree 3, Type of action 1.AA.
84
TFRX24-MFT Actuators, Multi-Function Technology
Wiring Diagrams
W024

4 ZG-R01 may be used.

W025
2 to 10 VDC Control Signal
4 to 20 mA Control Signal
85
LF Actuators, On/Off
D1367
D
C
E F B
A
LF
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
Models
LF24 US B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
LF24-S US w/built-in Aux. Switch B217(B)-B220(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
LF120 US B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
LF120-S US w/built-in Aux. Switch B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]

D1368
Power supply
LF24(-S) US 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%
LF120(-S) US 120 VAC ± 10% 50/60 Hz
Power consumption
LF24(-S) US running 5W D C
holding 2.5 W
LF120(-S) US running 5.5 W
holding 3.5 W
Transformer sizing
LF24(-S) US 7 VA, class 2 power source
E F B

LF120(-S) US 7.5 VA, class 2 power source
A
LF
(-S models have 2 cables) 3 ft [1m], 18 GA appliance cable
Electrical protection 120V actuators double insulated
Overload protection electronic throughout rotation
B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Spring return direction reversible with CW/CCW mounting
B317(B)-B320(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Position indication visual indicator 0° to 90°
B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
Running time motor <40 to 75 seconds (on/off)
spring <25 sec. @-4°F to 122°F [-20°C to 50°C]
<60 sec. @-22°F [-30°C]
Ambient temperature -22° F to 122° F [-30° C to 50° C]
Housing NEMA 2
Agency listings† cULus according to UL 873 and CAN/CSA
C22.2 No. 24-93
Noise level (max) running <30 db(A)
spring return 62 dB(A)
LF...-S US
adjustable 0° to 95° (double insulated)
86
WARNING
LF Actuators, On/Off
Wiring Diagrams
W047
24 VAC Transformer
Line 1 Common
Volts 2 + Hot 3
2 CAUTION Equipment damage! LF24 US 2

Power consumption must be observed. On/Off wiring for 24 VDC
W049-LF-08
4 LF24-S US and LF120-S US incorporates a built-in auxiliary switch:
1 x SPDT, 6A (1.5A) @ 250 VAC, UL listed, adjustable 0° to 95°.

Meets cULus or UL and CSA requirements without the Actuators may be connected in parallel. Power consumption
need of an electrical ground connection. 2 must be observed.
3 Actuator may also be powered by 24VDC.

During installation, testing, servicing and troubleshooting of this product, it may On/Off wiring for 120 VDC
W048-AUX
Auxiliary Switch
W047
87
LF24-3 Actuators, Floating Point
D1367
D
C
E F B
A
LF
Models B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
LF24-3 US B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
LF24-3-S US w/built-in Aux. Switch B217(B)-B220(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
D1368
holding 1W
Input impedance 1000 Ω (0.6w) control inputs D C
Position indication visual indicator 0° to 90°
Running time motor 150 seconds constant independent of load E F

B
spring <25 seconds @ -4°F to 122°F [-20°C to 50°C]
A
<60 seconds @ -22°F [-30°C]
LF
Storage temperature -40° F to 176° F [-40° C to 80° C]
B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Housing material zinc coated metal
B317(B)-B320(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Agency listings cULus according to UL 873 and CAN/CSA
B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
C22.2 No. 24-93
LF24-3-S US
88
LF24-3 Actuators, Floating Point
Wiring Diagrams
W054
24 VAC Transformer
Line
Volts
CAUTION Equipment damage! WARNING 2 8
2 Actuators may be connected in parallel. Live Electrical Components!

Hot Com
Blk (1) Common
Power consumption must be observed. servicing and troubleshooting
of this product, it maybe Red (2) + Hot
Triac sink necessary to work with live
3 Actuators may also be powered by 24 VDC. electrical components. Have Wht (3) +
or other individual who has Grn (4) +
The common connection from the actuator must be connected to the been properly trained in
4 Hot connection of the controller. handling live electrical
components perform these
CW CCW
tasks. Failure to follow all LF24-3(-S) US
5 The actuator Hot must be connected to the control board common. electrical safety precautions
components could result in Controller The indication of direction is
For end position indication, interlock control, fan startup, etc., death or serious injury.
valid for switch position CW.
6 LF24-3-S US incorporates one built-in auxiliary switch: 1 x SPDT, 6A Triac source

(1.5A) @ 250 VAC, UL listed, adjustable 0° to 95°.
W055
Actuators with plenum rated cable do not have numbers on wires; 24 VAC Transformer
Line
8 use color coded instead. Actuators with appliance rated cable use Volts
numbers. WARNING 2 8
During installation, testing, Hot Com
Triac sinkandwith
servicing separate transformers
troubleshooting Blk (1) Common 4
of this product, it maybe
Red (2) + Hot
Meets cULus or UL and CSA requirements without the necessary to work with live
Notes:
electrical components. Have 5
On-Off control ofneed of an
LF24-3 (-S)electrical
US ground connection. a qualified licensed electrician Wht (3) +
been properly trained in Actuators may be connected in parallel. Power Grn consumption
(4) +
2
WARNING Live Electrical Components! handling live electrical
must be observed.
CW CCW
During installation, testing, servicing and troubleshooting of this product, it may tasks. Failure to follow all
8 Actuators with plenum rated cable do not have numbersLF24-3(-S)
on wires;US use color codes
be necessary to work with live electrical components. Have a qualified licensed electrician when exposed to live electricalActuators with appliance rated cable use numbers.
Controller
or other individual who has been properly trained in handling live electrical components death or serious injury.
The indication of direction is valid for switch position CW.
Triac sink
W056
24 VAC Transformer 24 VAC Transformer
W061
WARNING 24 VAC Transformer 2 8 Line Line

3 WARNING
Live Electrical Components! Volts Volts 2 8
Line Blk (1) Common During installation, testing,
of this product, it maybe Volts
servicing and troubleshooting Blk (1) Common
Red (2) + of this product, it maybe
Hot Com
necessary to work with live necessary to work with live Red (2) + Hot 5
electrical components. Have
a qualified licensed electrician Wht (3) + electrical components. Have W054
a a qualified licensed electrician Wht (3) +
Grn (4) + Notes:
been properly trained in
been properly trained in Grn (4) +
a open handling live electrical
tasks. Failure to follow all a closed components Actuators
perform these may be connected in parallel. Power consumption CW CCW
Floating pointelectrical
control safetyof LF24-3 (-S) US
precautions
CW CCW 2 must be observed.
tasks. Failure to follow all
LF24-3(-S) US

when exposed to live electrical The indication of direction LF24-3(-S) US when exposed to live electrical
components could result in is valid for switch position CW. components The Common
could result in
Controller
connection from the actuator must be connected to the
death or serious injury. death4 or serious injury. The indication of direction is valid for switch position CW.
Hot connection of the controller.
On/Off control
5
Triac sink with separate transformers
The actuator Hot must be connected to the control board Common.
W052
8 Actuators with plenum rated cable do not have numbers on wires; use color codes instead.
WARNING Actuators with appliance rated cable use numbers.
Line Blk (1) Common
servicing and troubleshooting Volts Red (2) +
of this product, it maybe Notes:
necessary to work with live a Wht (3) +
Notes: electrical components. Have Installation Side
2 must be observed.
xx
xx
xx
xx
xx
xx xx
xx

xx
xx
xx xx
Grn (4) +
xx xx
xx
b
xx
xx xx
x x
2 Actuators may
been properly be inconnected
trained
in parallel.
Switch
CCW Power
CW consumption must be observed.
Direction of Rotation Switch
Positions
components perform these a b CW CCW 5 The actuator Hot must be connected to the control board Common.
tasks. Failure to follow all Auxiliary
(3) (4)switch
CW CC CCW ofCW LF24-3
CCW
CC (-S) US
3 Mayelectrical
also be powered by 24 VDC.
safety precautions LF24-3(-S) US
when exposed to live electrical stop stop stop stop
8
W055
Actuators with plenum rated cable do not have numbers on wires; use color codes instead.
8 Actuators with plenum rated cable do not have numbers on wires; use color codes instead.
death or serious injury. The indication of direction
Actuators with appliance rated cable use numbers.
Actuators with appliance rated cable use numbers.
is valid for switch position CW.

W053
WARNING
Notes: During installation, testing, servicing and S1 6
troubleshooting of this product, it maybe NC
S2
2 Actuators may components.
be connected Have a qualified licensed
in parallel. Power
consumption must be observed.
S3 0° to 95°
NO
3 May also be powered by 24 VDC.
LF24-3-S US W056
exposed to live electrical components could
result in death or serious injury. W051
8Actuators with plenum rated cable do not have numbers on wires; use color codes instead.
Auxiliary switchwith appliance rated cable use numbers.
Actuators

6 LF24-3 (-S) US incorporates one built-in auxiliary switch: 1 x SPDT,
89
LF24-SR Actuators, Proportional
D1367
D
C
E F B
A
LF
B207(B)-B211(B) ½” 15 2.41” [61.1] 1.39” [35.2]
Models B212(B)-B215(B) ½” 15 2.38” [60.4] 1.78” [45.2]
LF24-SR US
LF24-SR-S US w/built-in Aux. Switch B217(B)-B220(B) ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
Control proportional
Control signal 2 to 10 VDC Dimensions with 3-Way Valve
4 to 20 mA (with 500 Ω resistor)
D1368
holding 1W
Transformer sizing 5 VA, class 2 power
D C
Feedback output 2 to 10 VDC
Input impedance 100 kΩ
motor reversible with built-in switch E F B

Position indication visual indicator A
Running time motor 150 sec. independent of load (proportional) LF
spring <25 seconds @ -4°F to 122°F [-20°C to 50°C] Valve Nominal Size Dimensions (Inches [mm])
<60 seconds @ -22°F [-30°C]
B307(B)-B311(B) ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
Housing NEMA 2
B312(B)-B315(B) ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
B317(B)-B320(B) ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
C22.2 No. 24-93
B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
LF24-SR-S US
90
LF24-SR
WARNING
Wiring Diagrams
W057
4 to 20 mA control LF24-SR (-S) US with 2 to410 VDC feedback output
24 VACofTransformer
Line Blk (1) Common
2 CAUTION Equipment damage! Volts Red (2) + Hot

3
Actuators may be connected in parallel. Up to 4 actuators may be Wht (3) Y1 Input, 2 to 10V
connected in parallel. With 4 actuators wired to one 500 Ω resistor, a Control Signal (–)
2 to 10 VDC (+)
+2% shift of control signal may be required. Power consumption Grn (5) U Output, 2 to 10V
must be observed. 7
CW CCW
WARNING 2
3 Actuators may also be powered by 24 VDC. Live Electrical Components!
LF24-SR
During installation, testing, servicing and troubleshooting of this product, it maybe US
Actuators with plenum rated cable do not have numbers on wires; necessary to work with live electrical components. Have a qualified licensed electrician
4 2 to 10 VDC control or other individual who has been properly trained in handling live electrical components
use color codes instead. perform these tasks. Failure to follow all electrical safety precautions when exposed
W059
5 Only connect common to neg. (–) leg of control circuits. 24 VAC Transformer 4
For end position indication, interlock control, fan startup, etc., Line Blk (1) Common
6 LF24-SR-S US incorporates one built-in auxiliary switch: 1 x SPDT, 6A Volts
3
Red (2) + Hot
(1.5A) @ 250 VAC, UL listed, adjustable 0° to 95°. Ω
Notes: 500Ω
4 to 20 mA (–)
7 The LF24-SR-S US wire 5 is white. Wht (3) Y1 Input, 2 to 10V
Signal (+) may be connected in
Control Actuators parallel. Power consumption
2
2 to 10and
VDCinput
(–) impedance must be observed.
Feedback Signal (+) Grn (5) U Output, 2 to 10V
5 CW CCW
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to To other
actuators 2
2 to 10 VDC, up to 2 actuators may be connected in parallel. Actuators with plenum rated cable do not have numbers on
Auxiliary switches of LF24-SR-S US
4 wires; use color codes instead. LF24-SR US
need of an electrical ground connection. 4 to 20 mA control 7 The LF24-SR-S US wire 5 is white.
W058
WARNING
be necessary to work with live electrical components. Have a qualified licensed electrician Live Electrical Components!
or other individual who has been properly trained in handling live electrical components During installation, testing, servicing and S1 6
perform these tasks. Failure to follow all electrical safety precautions when exposed to live Notes:
NC
electrical components could result in death or serious injury. components. Have a qualified licensed S2
Up to 4 actuators may be connected in parallel. With
2 properly
4 actuators wiredlive
trained in handling one 500Ω resistor, S3
to electrical a +2% shift0°
of to 95°
NO
control perform
components signalthesemay beFailure
tasks. required.
to Power consumption
must be observed. W057
exposed to live electrical components could LF24-SR-S US
Auxiliary switch
Actuators with plenum rated cable do not have numbers
4 on wires; use color codes instead.

A 500Ω resistor converts the 4… 20mA control

signal to 2 to 10 VDC. (ZG-R01)
6 LF24-SR-S US incorporates one built-in auxiliary switch: 1 x SPDT,
Meets UL and CSA requirements without the need of an

W059
W058
91
LF24-MFT Actuators, Multi-Function Technology
D1367
D
C
E F B
A
LF
B207-B211 ½” 15 2.41” [61.1] 1.39” [35.2]
Models
LF24-MFT US B212-B215 ½” 15 2.38” [60.4] 1.78” [45.2]
LF24-MFT-S US w/built-in Aux. Switch B217-B220 ¾” 20 2.73” [69.3] 1.87” [47.4]
B222-B225 1” 25 3.09” [78.4] 1.87” [47.4]
B229-B230 1¼” 32 3.72” [94.6] 1.87” [47.4]
Technical Data
Control MFT
Control signal 2 to 10 VDC Dimensions with 3-Way Valve
D1368
holding 1W
Feedback output 2 to 10 VDC, 0.5 mA max D C
500 Ω for 4 to 20mA
750 Ω for PWM
500 Ω for on/off and floating point
E F

Direction of rotation spring reversible with CW/CCW mounting B
A
LF
Running time motor 150 seconds independent of load
(proportional, default)
B307-B311 ½” 15 2.41” [61.1] 1.39” [35.2] 1.20” [30.6]
spring <25 seconds @-4°F to 122°F [-20°C to 50°C]
<60 seconds @-22°F [-30°C] B312-B315 ½” 15 2.38” [60.4] 1.78” [45.2] 1.29” [32.8]
Ambient temperature -22° F to 122° F [-30° C to 50° C] B317-B320 ¾” 20 2.73” [69.3] 1.87” [47.4] 1.47” [37.3]
Housing NEMA 2 B322-B325 1” 25 3.09” [78.4] 1.87” [47.4] 1.59” [40.3]
C22.2 No. 24-93
LF24-MFT-S US
92
LF24-MFT Actuators,
Wiring Multi-Function
– PWM, triacTechnology
WARNING
source and s
Wiring Diagrams
W043
24 VAC/DC Transformer
Line (1) Common

Volts
2 CAUTION Equipment damage! (2) Hot
Actuators may be connected in parallel if not mechanically mounted to a
Position (–)
the same shaft. Power consumption and input impedance must be (3) Y Input
observed. Feedback VDC (+) (5) U Output
WARNING CCW CW
3 Actuators may also be powered by 24 VDC. Live Electrical Components! …MFT
4 IN4004 or IN4007 diode (IN4007 supplied, Belimo part number 40155). or other individual who has been properly trained in handling live electrical components
On/Off control perform these tasks. Failure to follow all electrical safety precautions when exposed
5 Triac A and B can also be contact closures.
W041
24 VAC Transformer (AC only)
Control signal may be pulsed from either the Hot (Source) or
6 Common (Sink) 24 VAC line. Line (1) Common
Volts 6
(2) + Hot
7 The actuators internal common reference is not compatible. (3) Y Input
7 Position (–)
Feedback VDC (+) (5) U Output
CCW CW
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to …MFT
PWM, triac source and sink
W302
W303
Proportional 2 to 10 or 4 to 20 mA control signal
93
AFRB24(-S), AFRX24(-S) Actuators, On/Off AFRB24(-S), AFRX24(-S) Actuators, On/Off
Dimensions
Dimensions
D1369
D C
E F B
A
Models AFRB, AFRX
AFRB24
AFRB24-S
AFRX24
AFRX24-S B212-B216 ½” 15 2.38” [60.4] 1.72” [43.7]
B217-B221 ¾” 20 2.73” [69.3] 1.81” [45.9]
B222-B225 1” 25 3.09” [78.4] 1.81” [45.9]
Power supply 24 VAC ± 20% 50/60 Hz B231-B232 1¼” 32 3.72” [94.6] 1.98” [50.4]
24 VDC +20% / -10% B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
Power consumption running 5 W B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
holding 2.5 W B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
Transformer sizing 7.5 VA (class 2 power source) B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
Electrical connection B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
AFRB24... 3 ft., 18 GA appliance cable, 1/2" conduit
connector
-S models: two 3 ft., 18 gauge appliance
cables with 1/2” conduit connectors
AFRX24... 3 ft. [1m], 10 ft. [3m] or 16 ft. [5m] 18 GA
appliance or plenum cables, with or without
Dimensions
1/2” conduit connector
D1370
-S models: two 3 ft. [1m], 10 ft. [3m] or
16 ft. [5m] appliance cables, with or without
1/2" conduit connectors

Control on/off D C
Running time motor < 75 seconds
spring 20 seconds @ -4°F to 122°F [-20°C to 50°C];
< 60 seconds @ -22°F [-30°C]
Position indication visual indicator, 0° to 95° E F B
A
(0° is full spring return position)
Manual override 5 mm hex crank (3/16" Allen), supplied AFRB, AFRX
Ambient temperature -22°F to 122°F [-30°C to 50°C] Valve Nominal Size Dimensions (Inches [mm])
Storage temperature -40°F to 176°F [-40°C to 80°C] Valve Body Inches DN [mm] A B C
Housing NEMA 2, IP54, Enclosure Type2 B312-B316 ½” 15 2.38” [60.4] 1.72” [43.7] 1.26” [32.1]
Agency listings † cULus according. to UL60730-1A/-2-14, B317-B321 ¾” 20 2.73” [69.3] 1.81” [45.9] 1.45” [36.8]
CAN/CSA E60730-1:02, CE according. to
B322-B325 1” 25 3.09” [78.4] 1.81” [45.9] 1.56” [39.8]
2004/108/EC & 2006/95/EC
B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
Noise level <50dB(A) motor @ 75 seconds
B338-B341 1½” 40 4.39” [111.6] 2.45” [62.2] 2.33” [59.1]
<62dB(A) spring return
B347-B352 2” 50 4.90” [124.5] 2.68” [68.0] 2.60” [66.0]
AFRB24-S, AFRX24-S
Auxiliary switches 2 x SPDT 3A (0.5A) @ 250 VAC, UL approved
one set at +10°, one adjustable 10° to 90°
800-543-9038
800-543-9038USA
USA 866-805-7089
866-805-7089CANADA
CANADA 203-791-8396 LATIN AMERICA
203-791-8396 / CARIBBEAN
LATIN AMERICA
94 97
AFRB24(-S), AFRX24(-S) Actuators, On/Off AFRB24(-S), AFRX24(-S) Actuators, On/Off
Wiring Diagrams
W063_AFB(X)
1 Provide overload protection and disconnect as required. Line 1 Common

Volts 3
CAUTION Equipment Damage! 2 + Hot
2
AFB24, AFB24-S
Actuators may also be powered by 24 VDC. AFX24, AFX24-S 2
3
4 On/Off wiring for AFRB24, AFRX24
AFRB24-S and AFRX24-S incorporates two built-in auxiliary switches:
2 x SPDT, 3A (0.5A) @250 VAC, UL Approved, one switch is fixed at
W064_AFB(X)_-S
+10°, one is adjustable 10° to 90°.

connection.
WARNING
G Live Electrical Components!
AFB24-S
AFX24-S
Auxiliary Switches for AFRB24-S, AFRX24-S

800-543-9038 USA 866-805-7089 CANADA 203-791-8396

203-791-8396
LATIN AMERICA / CARIBBEAN
LATIN AMERICA
98 95
AFRBUP(-S), AFRXUP(-S) Actuators, On/Off AFRBUP(-S), AFRXUP(-S) Actuators, On/Off
Dimensions
Dimensions
D1369
D C
E F B
A
AFRB, AFRX
AFRBUP Valve Body Inches DN [mm] A B
AFRBUP-S
B212-B216 ½” 15 2.38” [60.4] 1.72” [43.7]
AFRXUP
B217-B221 ¾” 20 2.73” [69.3] 1.81” [45.9]
AFRXUP-S
B222-B225 1” 25 3.09” [78.4] 1.81” [45.9]
B229-B230 1¼” 32 3.72” [94.6] 1.81” [45.9]
Power supply 24 to 240 VAC -20% / +10%, 50/60 Hz B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
24 to 125 VDC +10% B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
Power consumption running 7 W B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
holding 3.5 W B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
Transformer sizing 7 VA @ 24 VAC (class 2 power source) B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
8.5 VA @ 120 VAC
18 VA @ 240 VAC
Electrical connection
AFRBUP... 3 ft., 18 GA appliance cable, 1/2" conduit
connector
-S models: two 3 ft., 18 gauge appliance Dimensions
D1370
AFRXUP... 3 ft. [1m], 10 ft. [3m] or 16 ft. [5m] 18 GA

-S models: two 3 ft. [1m], 10 ft. [3m] or C
D
Control on/off
Angle of rotation 95° (adjustable with mechanical end stop, 35° E F B
A
to 95°)
Running time motor < 75 seconds AFRB, AFRX
spring 20 seconds @ -4°F to 122°F [-20°C to 50°C]; Valve Nominal Size Dimensions (Inches [mm])
< 60 seconds @ -22°F [-30°C] Valve Body Inches DN [mm] A B C
Position indication visual indicator, 0° to 95° B312-B316 ½” 15 2.38” [60.4] 1.72” [43.7] 1.26” [32.1]
(0° is full spring return position) B317-B321 ¾” 20 2.73” [69.3] 1.81” [45.9] 1.45” [36.8]
Manual override 5 mm hex crank (3/16" Allen), supplied B322-B325 1” 25 3.09” [78.4] 1.81” [45.9] 1.56” [39.8]
Ambient temperature -22°F to 122°F [-30°C to 50°C] B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
Storage temperature -40°F to 176°F [-40°C to 80°C] B338-B341 1½” 40 4.39” [111.6] 2.45” [62.2] 2.33” [59.1]
Housing NEMA 2/IP54, Enclosure Type2 B347-B352 2” 50 4.90” [124.5] 2.68” [68.0] 2.60” [66.0]
Agency listings † cULus according. to UL60730-1A/-2-14,
2004/108/EC & 2006/95/EC
AFRBUP-S, AFRXUP-S
96
AFRBUP(-S), AFRXUP(-S) Actuators, On/Off AFRBUP(-S), AFRXUP(-S) Actuators, On/Off
Wiring Diagrams
W066_AFB(X)UP

3 No ground connection is required.

4 AFRBUP-S and AFRXUP-S incorporates two built-in auxiliary switches: AFBUP, AFBUP-S
AFXUP, AFBUP-S
+10°, one is adjustable 10° to 90°.
On/Off wiring for AFRBUP, AFRXUP
W067_AFB(X)UP-S
connection. Wht
Blk
WARNING
AFBUP-S
AFXUP-S
Auxiliary Switches for AFRBUP-S, AFRXUP-S
800-543-9038USA
800-543-9038 USA 866-805-7089CANADA
866-805-7089 CANADA 203-791-8396
203-791-8396 LATIN AMERICA
100 97
AFRB24-SR, AFRX24-SR
Proportional, Spring Return, 24 V, for 2 to 10 VDC or 4 to 20 mA Control Signal
Dimensions
D1369
Dimensions (Inches [mm])
D C
AFR_DIM
E F B
A
AFRB, AFRX
Technical Data Valve Body Inches DN [mm] A B
Power supply 24 VAC ±20%, 50/60 Hz B212-B216 ½” 15 2.38” [60.4] 1.72” [43.7]
24 VDC +20% / -10% B217-B221 ¾” 20 2.73” [69.3] 1.81” [45.9]
Power consumption running 5.5 W B222-B225 1” 25 3.09” [78.4] 1.81” [45.9]
holding 3 W B229-B230 1¼” 32 3.72” [94.6] 1.81” [45.9]
Transformer sizing 8.5 VA (class 2 power source) B231-B232 1¼” 32 3.72” [94.6] 1.98” [50.4]
Electrical connection B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
AFRB... 3 ft, 18 GA appliance cable, 1/2" conduit B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
connector B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
-S models: two 3 ft, 18 gauge appliance cables B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
with 1/2” conduit connectors B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
AFX... 3 ft [1m], 10 ft [3m] or 16 ft [5m] 18 GA
appliance or plenum cables, with or without 1/2”
conduit connector
-S models: Two 3 ft [1m], 10 ft [3m] or
16 ft [5m] appliance cables, with or without 1/2"
conduit connectors Dimensions
D1370
Operating range Y 2 to 10 VDC, 4 to 20mA
Input impedance 100 kΩ for 2 to 10 VDC (0.1 mA)
500 Ω for 4 to 20 mA
Feedback output U 2 to 10 VDC (max. 0.5 mA)
- 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

Direction of rotation spring reversible with CW/CCW mounting D C
N40103 - 09/11 - Subject to change. © Belimo Aircontrols (USA), Inc.

Mechanical angle of rotation 95° (adjustable with mechanical end stop, 35° to
95°)
Running time spring < 20 seconds @ -4°F to 122°F [-20°C to 50°C];
< 60 seconds @ -22°F [-30°C]
E F B
motor 95 seconds A
AFRB, AFRX
Manual override 5 mm hex crank (³⁄₁₆" Allen), supplied Valve Nominal Size Dimensions (Inches [mm])
Humidity max. 95% RH non-condensing Valve Body Inches DN [mm] A B C
Ambient temperature -22°F to 122°F [-30°C to 50°C] B312-B316 ½” 15 2.38” [60.4] 1.72” [43.7] 1.26” [32.1]
Storage temperature -40°F to 176°F [-40°C to 80°C] B317-B321 ¾” 20 2.73” [69.3] 1.81” [45.9] 1.45” [36.8]
Housing Nema 2, IP54, Enclosure Type2 B322-B325 1” 25 3.09” [78.4] 1.81” [45.9] 1.56” [39.8]
Housing material zinc coated metal and plastic casing B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
Agency listings† cULus acc. to UL60730-1A/-2-14, CAN/CSA B338-B341 1½” 40 4.39” [111.6] 2.45” [62.2] 2.33” [59.1]
E60730-1:02, CE acc. to 2004/108/EC &
P10419
B347-B352 2” 50 4.90” [124.5] 2.68” [68.0] 2.60” [66.0]

2006/95/EC
Noise level ≤40dB(A) motor @ 95 seconds
≤62dB(A) spring return
Weight 4.6 lbs (2.1 kg); 4.9 lbs (2.25 kg) with switches
800-543-9038
800-543-9038USA
USA 866-805-7089
866-805-7089 CANADA
CANADA 203-791-8396
203-791-8396LATIN AMERICA/ CARIBBEAN
98
57
AFRB24-SR, AFRX24-SR
Proportional, Spring Return, 24 V, for 2 to 10 VDC to 4 to 20 mA Control Signal
Accessories WARNING
AV 8-25 Shaft extension During installation, testing, servicing and troubleshooting of this product, it may be
IND-AFB Damper position indicator necessary to work with live electrical components. Have a qualified licensed electrician or other
individual who has been properly trained in handling live electrical components perform these
KH-AFB Crank arm
tasks. Failure to follow all electrical safety precautions when exposed to live electrical compo-
K7-2 Universal clamp for up to 1.05” dia jackshafts nents could result in death or serious injury.
TF-CC US Conduit fitting
Tool-06 8mm and 10 mm wrench
W068_AFB(X)24-SR
ZG-100 Universal mounting bracket
ZG-101 Universal mounting bracket
Line 1 Common
ZG-118 Mounting bracket for Barber Colman® MA 3../4.., Honeywell® 3
Volts
Mod III or IV or Johnson® Series 100 replacement or new crank 2 + Hot
arm type installations 3 Y1 Input, 2 to 10V
ZG-AFB Crank arm adaptor kit Control Signal (–)
ZG-AFB118 Crank arm adaptor kit 2 to 10 VDC (+)
ZS-100 Weather shield (metal) 5 U Output 2 to 10V
ZS-150 Weather shield (polycarbonate)
AFB24-SR, AFB24-SR-S
ZS-260 Explosion-proof housing AFX24-SR, AFX24-SR-S
2
ZS-300 NEMA 4X housing
NOTE: When using AFRB24-SR, AFRB24-SR-S, AFRX24-SR and AFRX24-SR-S actuators, only use
2 to 10 VDC control of AFRB24-SR and AFRX24-SR
accessories listed on this page.
For actuator wiring information and diagrams, refer to Belimo Wiring Guide.
W069_AFB(X)24-SR
Typical Specification
Spring return control damper actuators shall be direct coupled type which require no
crank arm and linkage and be capable of direct mounting to a jackshaft up to a 1.05”
diameter. The actuator must provide proportional damper control in response to a 2 to
10 VDC or, with the addition of a 500Ω resistor, a 4 to 20 mA control input from an
electronic controller or positioner. The actuators must be designed so that they may be
used for either clockwise or counterclockwise fail-safe operation. Actuators shall use
a brushless DC motor controlled by a microprocessor and be protected from overload
at all angles of rotation. Run time shall be constant, and independent of torque. A 2 to
10 VDC feedback signal shall be provided for position feedback. Actuators shall be
cULus Approved and have a 5 year warranty, and be manufactured under ISO 9001 AFB24-SR, AFB24-SR-S
International Quality Control Standards. Actuators shall be as manufactured by Belimo. AFX24-SR, AFX24-SR-S
4 to 20 mA control of AFRB24-SR and AFRX24-SR with

Wiring Diagrams 2 to 10 VDC feedback output
W064_AFB(X)24_SR_-S
N40103 - 09/11 - Subject to change. © Belimo Aircontrols (USA), Inc.

Up to 4 actuators may be connected in parallel if not mechanically mounted
2 to the same shaft. With 4 actuators wired to one 500 Ω resistor.
Power consumption must be observed.

For end position indication, interlock control, fan startup, etc., AFB24-SR-S
4 and AFX24-SR-S incorporates two built-in auxiliary switches: 2 x SPDT, 3A
AFB24-SR-S
(0.5A) @250 VAC, UL Approved, one switch is fixed at +10°, one is adjust- AFX24-SR-S
able 10° to 90°.
Auxiliary switches for AFRB24-SR-S, AFX24-SR-S
5 Only connect common to neg. (–) leg of control circuits
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to

2 to 10 VDC.
ATTENTION:
ATTENTION AFRB24-SR(-S)
AFRB24 AFRX24 SR( S) cannott bbe tandem
SR( S) andd AFRX24-SR(-S) t d mounted t d
on the same damper or valve shaft. Only On/Off and MFT AF models can be used
for tandem mount applications.
800-543-9038USA
800-543-9038 USA 866-805-7089CANADA
866-805-7089 CANADA 203-791-8396LATIN
203-791-8396 LATIN AMERICA
AMERICA / /CARIBBEAN
CARIBBEAN
58
99
AFRX Actuators, Multi-Function Technology
Dimensions
D1369
D C
E F B
A
Models AFRB, AFRX
AFRX24-MFT
AFRX24-MFT-S Valve Nominal Size Dimensions (Inches [mm])
Technical Data B212-B216 ½” 15 2.38” [60.4] 1.72” [43.7]
Control MFT B217-B221 ¾” 20 2.73” [69.3] 1.81” [45.9]
Control signal 2 to 10 VDC, 4 to 20 mA (default) B222-B225 1” 25 3.09” [78.4] 1.81” [45.9]
variable (VDC, PWM, floating point, on/off) B229-B230 1¼” 32 3.72” [94.6] 1.81” [45.9]
Power supply 24 VAC, +/- 20%, 50/60 Hz B231-B232 1¼” 32 3.72” [94.6] 1.98” [50.4]
24 VDC, +20% / -10% B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
Power consumption† running 7.5 W B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
holding 3W B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
Transformer sizing† 10 VA (Class 2 power source) B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
Electrical connection 3 ft. [1m], 10 ft. [3m] or 16 ft. [5m] 18 GA B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
1/2" conduit connector
-S models: two 3 ft. [1m], 10 ft. [3m] or 16
ft. [5m] appliance cables with or without 1/2”
conduit connectors
Overload protection electronic throughout 0 to 90° rotation Dimensions
Feedback output* 2 to 10 VDC, 0.5 mA max (variable)
D1370
1500 Ω for on/off and floating point

Direction of rotation* spring reversible with CW/CCW mounting D C
Position indication visual indicator 0° to 95°(0° is spring return
position)
Manual override 5 mm hex crank (3/16” Allen), supplied
Running time motor* 150 seconds (default),
E F B
variable (70 to 220 seconds) A
Ambient temperature -22° F to 122° F [-30° C to 50° C] AFRB, AFRX
Housing NEMA 2, IP54, Enclosure Type 2 Valve Nominal Size Dimensions (Inches [mm])
Agency listings cULus according. To UL60730-1A/-2-14, Valve Body Inches DN [mm] A B C
CAN/CSA E60730- 1:02, CE according. To B312-B316 ½” 15 2.38” [60.4] 1.72” [43.7] 1.26” [32.1]
2004/108/EC & 2006/95/EC B317-B321 ¾” 20 2.73” [69.3] 1.81” [45.9] 1.45” [36.8]
Noise level <40dB(A) motor @ 150 seconds, run time B322-B325 1” 25 3.09” [78.4] 1.81” [45.9] 1.56” [39.8]
dependent B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
<62dB(A) spring return B338-B341 1½” 40 4.39” [111.6] 2.45” [62.2] 2.33” [59.1]
Quality standard ISO 9001 B347-B352 2” 50 4.90” [124.5] 2.68” [68.0] 2.60” [66.0]
† Programmed for 70 sec motor runtime. At 150 sec motor run time, transformer sizing
is 8.5 VA and power consumption is 6 W running/3 W holding.
‡ Rated Impulse Voltage 800V, Type of action 1.AA (1.AA.B for -S version), Control
Pollution Degree 3.
AFRX24-MFT-S
one set at +10° to 90°
100
AFRX Actuators, Multi-Function Technology
Dimensions
W600_AFB_AFX
AFR_LGCCV
D
I
C
G AFB24-MFT-S
AFX24-MFT-S
B
E F A Auxiliary Switches for AFRX24-MFT
AFRB, AFRX
W399_08
Nominal Top
Pipe Flange Height
Size Design
A B C
B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4]
B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1]
B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9]
VDC/4-20 mA
Wiring Diagrams
W399_08

Actuators may be connected in parallel if not mechanically mounted
to the same shaft. Power consumption and input impedance must be
observed.

4 The actuator internal common reference is not compatible. PWM
5
W399_08

connection.
The ZG-R01 500 Ω resistor may be used. On/Off control

W399_08

perform these tasks. Failure to follow all electrical safety precautions when exposed to
live electrical components could result in death or serious injury.
101
AFRX24-MFT95 Actuator, Proportional Potentiometric Control
Dimensions
D1369
D C
E F B
A
Models AFRB, AFRX
AFRX24-MFT95
Technical Data B212-B215 ½” 15 2.38” [60.4] 1.72” [43.7]
Control MFT B217-B221 ¾” 20 2.73” [69.3] 1.81” [45.9]
Control signal 0 to 135 Ω Honeywell Electronic Series 90, B222-B225 1” 25 3.09” [78.4] 1.81” [45.9]
0 to 135 Ω input B229-B230 1¼” 32 3.72” [94.6] 1.81” [45.9]
Power supply 24 VAC, +/- 20%, 50/60 Hz B231-B232 1¼” 32 3.72” [94.6] 1.98” [50.4]
24 VDC, +20% / -10% B238-B240 1½” 40 3.88” [98.5] 1.98” [50.4]
Power consumption† running 7.5 W B248-B250 2” 50 4.21” [107.0] 2.21” [56.2]
holding 3W B251-B254 2” 50 4.93” [125.2] 2.68” [68.0]
Transformer sizing† 10 VA (Class 2 power source) B261-B265 2½” 65 5.55” [140.9] 2.68” [68.0]
Electrical connection 3 ft. [1m], 10 ft. [3m] or 16 ft. [5m] 18 GA B277-B280 3” 80 5.82” [147.9] 2.68” [68.0]
plenum cables, with or without 1/2" conduit
connector
Feedback output* 2 to 10 VDC, 0.5 mA max (variable)
Direction of rotation* spring reversible with CW/CCW mounting Dimensions
D1370
Position indication visual indicator 0° to 95°(0° is spring return
position)
Manual override 5 mm hex crank (3/16” Allen), supplied
Running time motor* 150 seconds (default),

D C
Housing NEMA 2, IP54, Enclosure Type 2
Agency listings cULus according. To UL60730-1A/-2-14,
CAN/CSA E60730- 1:02, CE according. To E F B
2004/108/EC & 2006/95/EC A
Noise level <40dB(A) motor @ 150 seconds, run time AFRB, AFRX
dependent
<62dB(A) spring return Valve Nominal Size Dimensions (Inches [mm])
Quality standard ISO 9001 Valve Body Inches DN [mm] A B C
† Programmed for 70 sec motor runtime. At 150 sec motor run time, transformer sizing B312-B315 ½” 15 2.38” [60.4] 1.72” [43.7] 1.26” [32.1]
is 8.5 VA and power consumption is 6 W running/3 W holding. B317-B321 ¾” 20 2.73” [69.3] 1.81” [45.9] 1.45” [36.8]
* Variable when configured with MFT options B322-B325 1” 25 3.09” [78.4] 1.81” [45.9] 1.56” [39.8]
‡ Rated Impulse Voltage 800V, Type of action 1.AA (1.AA.B for -S version), Control
B329-B331 1¼” 32 3.96” [100.6] 2.21” [56.2] 2.14” [54.3]
Pollution Degree 3.
B338-B341 1½” 40 4.39” [111.6] 2.45” [62.2] 2.33” [59.1]
B347-B352 2” 50 4.90” [124.5] 2.68” [68.0] 2.60” [66.0]
102
AFRX24-MFT95 Actuator, Proportional Potentiometric Control
Override of AF24-MFT95 US
Dimensions
W015_AFRX
D1378
Damper Open
Damper Closed
D The direction of rotation switch is set so that the fail safe position and the
I
24 VAC Transformer
C 1
Line 1 Common, Blk

Volts 2 + Hot, Red 3
A 4
G 3 W, Wht
135 4 R, Wht
B B
E F A
5 B, Wht
AFRB, AFRX AFRX24-MFT95
24 VAC Transformer
1
Nominal Top Line 1 Common, Blk
Pipe Flange Height Volts 2 + Hot, Red 3
Size Design 4
A
A B C W 3 W, Wht
Line R 4 R, Wht
B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4] Volts B
B 5 B, Wht
B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1] 2 Controller 6 ‘U5’ Output 2-10 VDC
B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9] AF24-MFT95 US used with AFRX24-MFT95
a Series 90
controller and a Series 90 low limit control
Override of AFRX24-MFT95
Wiring Diagrams 1 Provide overload protection and disconnect as required.
W016
2 Actuators and controller must have separate transformers.
24 VAC Transformer
1 Consult controller instruction data for more detailed
3
Line installation information. 1 Common, Blk
1 Provide overload protection and disconnect as required. 4 To reverse control rotation, use the
Volts 2 + 3
Hot, Redswitch.
reversing
4
2 Actuators and controller must have separate transformers. 2
W W B R 3 W, Wht
4 R, Wht
Consult controller instruction data for more detailed installation Series 90 R
3 information.
Controller
B 5 B, Wht
Series 90 low limit control

AF24-MFT95 US used with a Series 90
4 To reverse control rotation, use the reversing switch. 135 for 0 to 50% control
AFRX24-MFT95
280 for 0 to 100% control
controller and a Series 90 high limit control
Resistor value depends on the type of controller and the number of
actuators. No resistor is used for one actuator. Honeywell resistor
W017
5 1 Provide
kits may also be used. 24 VACoverload protection and disconnect as required.
Transformer W015
1
Line Consult controller instruction data1 for
Common, Blk
more detailed
WARNING Live Electrical Components! 3
Volts installation information. 2 + Hot, Red 3
4 To reverse control rotation, use the reversing switch.
be necessary to work with live electrical components. Have a qualified licensed electrician 2
4
or other individual who has been properly trained in handling live electrical components W 3 W, Wht
perform these tasks. Failure to follow all electrical safety precautions when exposed to live Series 90 R 4 R, Wht
electrical components could result in death or serious injury. Controller R W B 5 B, Wht
B
Series 90 high limit control - 280
AFRX24-MFT95
AFRX24-MFT95 used with a Series 90 controller

and a Series 90 low1limit control
Provide overload protection and disconnect as required.
Consult controller instruction data for more detailed
3
installation information.
4 To reverse control rotation, use the reversing switch.
W016
103
W017
AFRX24-MFT95 Actuator, Proportional Potentiometric Control AFRX24-MFT95
W018_AFRX
W020_AFRX
AFRX24-MFT95
AFRX24-MFT95
AFRX24-MFT95
Wiring multiple actuators to a Series 90 controller.

W019_AFRX
AFRX24-MFT95
AFRX24-MFT95

AFRX24-MFT95
AFRX24-MFT95
Wiring multiple actuators to a Series 90 controller

using a minimum position potentiometer.
AFRX24-MFT95
Typical wiring diagrams for multiple actuators used

with the W973, W7100 and T775 controllers.
104
AFRB24 N4, AFRB24 N4H, AFRB24-S N4, AFRB24-S N4H,
AFRX24 N4, AFRX24 N4H, AFRX24-S N4, AFRX24-S N4H
NEMA 4, On/Off, Spring Return, 24 V
D1363
D C
E F B
Models A
AFRB24 N4 Basic Version ARB N4, ARX N4, NRB N4, NRX N4
AFRB24 N4H Basic Version w/built in heater Valve Nominal Size Dimensions (Inches [mm])
AFRB24-S N4 Basic Version w/built-in aux. switch Valve Body Inches DN [mm] A B
AFRB24-S N4H Basic Version w/built-in aux. switch & heater B231-B232 1¼” 32 3.72” [94.6] 1.84” [47.4]
AFRX24 N4 Flexible Version B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
AFRX24-S N4 Flexible Version w/built-in aux. switch B248-B254 2” 50 4.93” [125.2] 2.73” [69.5]
AFRX24 N4H Flexible Version w/built in heater B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
AFRX24-S N4H Flexible Version aux. switch & heater
Technical Data
D1364
24 VDC +20% / -10%
Power consumption running 5 W / heater 25 W
holding 2.5 W
Transformer sizing 7.5 VA (class 2 power source) / heater 25 VA
Electrical connection 3 ft [1m], 10 ft [3m] or 16 ft [5m] 18 GA appliance
AFR... N4 cable, with or without 1/2” conduit connector
D C
16 ft [5m] appliance cables with or without 1/2” conduit
connectors
heater (N4H) terminal block, 26-16 GA E F B

Overload protection electronic throughout 0 to 95° rotation A
Control on/off
NRB N4, NRX N4

Torque 180 in-lb [20 Nm] minimum
Direction of rotation spring reversible with CW/CCW mounting in housing
Mechanical angle of rotation 95° (adjustable with mechanical end stop, 35° to 95°) Valve Body Inches DN [mm] A B C
Running time motor < 75 seconds B329-B332 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
spring 20 seconds @ -4°F to 122°F [-20°C to 50°C]; B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
< 60 seconds @ -22°F [-30°C] B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
spring (with heater) 20 seconds @ -4°F to 122°F [-20°C to 50°C], <60
seconds @ -49°F [-45°C]
Manual override 5 mm hex crank (³⁄₁₆" Allen), supplied
Humidity max. 95% RH non-condensing
with heater -49°F to 122°F [-45°C to 50°C]
Housing UL Type 4, NEMA 4, IP66
Housing material polycarbonate
Agency listings † cULus acc. to UL60730-1A/-2-14,
CAN/CSA E60730-1:02, CE acc. to
2004/108/EC & 2006/95/EC
Weight 9.7 lbs (4.4 kg); 10 lbs (4.5 kg) with switches;
10.5 lbs (4.8 kg) with heater
AFRB24-S N4, AFRB24-S N4H, AFRX24-S N4, AFRX24-S N4H

105
AFRB24 N4, AFRB24 N4H, AFRB24-S N4, AFRB24-S N4H,
AFRX24 N4, AFRX24 N4H, AFRX24-S N4, AFRX24-S N4H
NEMA 4, On/Off, Spring Return, 24 V
Accessories Wiring Diagrams

43442-00001 Gland (needed for additional wires)
11097-00001 Gasket for Gland (needed for additional wires)
NOTE: When using AFRB24 N4, AFRB24 N4H, AFRB24-S N4, AFRB24-S N4H, AFRX24 N4, 1 Provide overload protection and disconnect as required.
AFRX24 N4H, AFRX24-S N4, AFRX24-S N4H actuators, only use accessories listed on this page.
For actuator wiring information and diagrams, refer to Belimo Wiring Guide. 2 CAUTION Equipment Damage!
Typical Specification Power consumption and input impedance must be
The actuators must be designed so that they may be used for either clockwise or observed.
counterclockwise fail-safe operation. Actuators shall be protected from overload at all
angles of rotation. If required, two SPDT auxiliary switch shall be provided having the 3 Actuators may also be powered by 24 VDC.
capability of one being adjustable. Actuators with auxiliary switches must be For end position indication, interlock control, fan startup, etc., AFRB24-S
constructed to meet the requirements for Double Insulation so an electrical ground is 4 N4, AFRB24-S N4H, AFRX24-S N4, AFRX24-S N4H incorporates two built-in
not required to meet agency listings. Actuators shall be cULus Approved and have a 5 auxiliary switches: 2 x SPDT, 3A (0.5A) @250 VAC, UL Approved, one
year warranty, and be manufactured under ISO 9001 International Quality Control switch is fixed at +10°, one is adjustable 10° to 90°.
Standards. Actuators shall be as manufactured by Belimo.

connection.

necessary to work with live electrical components. Have a qualified licensed electrician or other
nents could result in death or serious injury.
W063_AFRBX24_N4
Line 1 Common
Volts 3
2 + Hot
AFRB24 N4
AFRB24 N4H 2
AFRB24-S N4
AFRB24-S N4H
AFRX24 N4
AFRX24-S N4

On/Off wiring
W064_AFRBX24_S_N4
2 must be observed.
3 Actuator may also be powered by 24VDC.
AFRB24-S N4
AFRB24-S N4H
AFRX24-S N4
AFRX24-S N4H
Auxiliary Switches
GK-AF-NF N4H 24V heater
NEMA 4 Heater W063

106
AFRBUP N4, AFRBUP-S N4, AFRBUP N4H, AFRBUP-S N4H,
AFRXUP N4, AFRXUP-S N4, AFRXUP N4H, AFRXUP-S N4H
NEMA 4, On/Off, Spring Return, 24 to 240 VAC
D1363
D C
E F B
Models A
AFRBUP N4 Basic Version
AFRBUP-S N4 Basic Version w/built-in aux. switch ARB N4, ARX N4, NRB N4, NRX N4
AFRBUP N4H Basic Version w/built in heater Valve Nominal Size Dimensions (Inches [mm])
AFRBUP-S N4H Basic Version w/built-in aux. switch & heater Valve Body Inches DN [mm] A B
AFRXUP N4 Flexible Version B231-B232 1¼” 32 3.72” [94.6] 1.84” [47.4]
AFRXUP-S N4 Flexible Version w/built-in aux. switch B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
AFRXUP N4H Flexible Version w/built in heater B248-B254 2” 50 4.93” [125.2] 2.73” [69.5]
AFRXUP-S N4H Flexible Version w/built-in aux. switch & heater B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
Technical Data
Power supply 24...240 VAC -20% / +10%, 50/60 Hz
24...125 VDC ±10%
Power consumption running 7 W / heater 25 W
D1364
holding 3.5 W
Transformer sizing 7 VA @ 24 VAC (class 2 power source)
8.5 VA @ 120 VAC / heater 25 VA @120 VAC
18 VA @ 240 VAC
AFRBUP... N4 3 ft [1m], 10 ft [3m] or 16 ft [5m] 18 GA appliance
AFRXUP... N4 cable, with or without 1/2” conduit connector D C
16 ft [5m] appliance cables with or without 1/2” conduit
connectors
heater (N4H) terminal block, 18-16 GA
E F B
Control on/off
A
Torque 180 in-lb [20 Nm] minimum
Direction of rotation spring reversible with CW/CCW mounting inside housing NRB N4, NRX N4
Mechanical angle of rotation 95° (adjustable with mechanical end stop, Valve Nominal Size Dimensions (Inches [mm])
35° to 95°) Valve Body Inches DN [mm] A B C
Running time motor < 75 sec B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
spring 20 sec @ -4°F to 122°F [-20°C to 50°C]; B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
< 60 sec @ -22°F [-30°C]
B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
spring (with heater) 20 sec @ -4°F to 122°F [-20°C to 50°C];
< 60 sec @ -49°F [-45°C]
with heater -49°F to 122°F [-45°C to 50°C]
Agency listings † cULus acc. to UL60730-1A/-2-14,
CAN/CSA E60730-1:02, CE acc. to
2004/108/EC & 2006/95/EC
Weight 9.7 lbs (4.4 kg), 10 lbs (4.5 kg) with switches
† Rated Impulse Voltage 4kV, Type of action 1.AA (1.AA.B for -S version), Control Pollution Degree 4.
AFRBUP-S N4, AFRBUP-S N4H, AFRXUP-S N4, AFRXUP-S N4H

Auxiliary switches 2 x SPDT 3A (0.5A) @ 250 VAC, UL Approved
107
AFRBUP N4, AFRBUP-S N4, AFRBUP N4H, AFRBUP-S N4H,
AFRXUP N4, AFRXUP-S N4, AFRXUP N4H, AFRXUP-S N4H
NEMA 4, On/Off, Spring Return, 24 to 240 VAC A
Accessories
W066_AFRBUP_N4
NOTE: When using AFRBUP N4, AFRBUP-S N4, AFRBUP N4H, AFRBUP-S N4H, AFRXUP N4,
AFRXUP-S N4, AFRXUP N4H, AFRXUP-S N4H actuators, only use accessories listed on this page.
For actuator wiring information and diagrams, refer to Belimo Wiring Guide.
AFRBUP N4
On/Off spring return damper actuators shall be direct coupled type which require
AFRBUP N4H
no crank arm and linkage and be capable of direct mounting to a jackshaft up to a AFRBUP-S N4
1.05” diameter. The actuators must be designed so that they may be used for either AFRBUP-S N4H
clockwise or counterclockwise fail-safe operation. Actuators shall be protected AFRXUP N4
from overload at all angles of rotation. If required, two SPDT auxiliary switch shall AFRXUP N4H
be provided having the capability of one being adjustable. Actuators with auxiliary AFRXUP-S N4
switches must be constructed to meet the requirements for Double Insulation so AFRXUP-S N4H
an electrical ground is not required to meet agency listings. Actuators shall be A
cULus Approved and have a 5 year warranty, and be manufactured under ISO 9001
International Quality Control Standards. Actuators shall be as manufactured by Belimo.
On/Off Wiring
W067_AFRBUP-S_N4
Wiring Diagrams
Wht
Blk


For end position indication, interlock control, fan startup, etc., AFRB24-S
4 N4, AFRB24-S N4H, AFRX24-S N4, AFRX24-S N4H incorporates two built-in
auxiliary switches: 2 x SPDT, 3A (0.5A) @250 VAC, UL Approved, one
switch is fixed at +10°, one is adjustable 10° to 90°.

connection.

necessary to work with live electrical components. Have a qualified licensed electrician or other
AFRBUP-S N4
nents could result in death or serious injury. AFRBUP-S N4H
AFRXUP-S N4
AFRXUP-S N4H
Auxiliary Switches AF-NF N4H 120V heater
NEMA 4A Heater
108
AFRB24-MFT N4, AFRB24-MFT-S N4, AFRB24-MFT N4H, AFRB24-MFT-S N4H
AFRX24-MFT N4, AFRX24-MFT-S N4, AFRX24-MFT N4H, AFRX24-MFT-S N4H
NEMA 4, Proportional, Spring Return, Direct Coupled, 24V, Multi-Function Technology®
D1363
Models
AFRB24-MFT N4 Basic Version
AFRB24-MFT-S N4 Basic Version w/built-in aux. switch D C
AFRB24-MFT N4H Basic Version w/built in heater
AFRB24-MFT-S N4H Basic Version w/built-in aux. switch & heater
AFRX24-MFT N4 Flexible Version
AFRX24-MFT-S N4 Flexible Version w/built-in aux. switch
AFRX24-MFT N4H Flexible Version w/built in heater E F B
AFRX24-MFT-S N4H Flexible Version w/built in aux. switch & heater A
Technical Data ARB N4, ARX N4, NRB N4, NRX N4
Power supply 24 VAC, +/- 20%, 50/60 Hz Valve Nominal Size Dimensions (Inches [mm])
24 VDC, +20% / -10%
Power running 7.5 W / heater 25 W
B231-B232 1¼” 32 3.72” [94.6] 1.84” [47.4]
consumption holding 3W
B238-B240 1½” 40 3.88” [98.5] 2.04” [51.9]
Transformer sizing 10 VA (Class 2 power source) / heater 25 VA
Electrical connection 3 ft [1m], 10 ft [3m] or 16 ft [5m] 18 GA appliance cables, with
B248-B254 2” 50 4.93” [125.2] 2.73” [69.5]
AFRB... N4 1/2” conduit connector B261-B265 2½” 65 5.55” [140.9] 2.73” [69.5]
AFRX... N4 -S models: two 3 ft [1m], 10 ft [3m] or B277-B280 3” 80 5.82” [147.9] 2.73” [69.5]
16 ft [5m] appliance cables with 1/2” conduit connectors
heater (N4H) terminal block, 26-16 GA
Overload protection electronic throughout 0 to 95° rotation Dimensions with 3-Way Valve1363
Operating range Y* 2 to 10 VDC, 4 to 20 mA (default)
D1364
1500 Ω for PWM, floating point and on/off control
Feedback output U* 2 to 10 VDC, 0.5 mA max
Torque minimum 180 in-lb (20 Nm)
D C
Direction of spring reversible with cw/ccw mounting inside housing
rotation* motor reversible with built-in switch
Mechanical 95° (adjustable with mechanical end stop, 35° to 95°)
angle of rotation*
Running time motor* 150 seconds (default), variable (70 to 220 seconds)
spring <20 sec @ -4°F to 122°F [-20°C to 50°C]; E F B
<60 sec @ -22°F [-30°C] A
spring (with heater) <20 sec @ -4°F to 122°F [-20°C to 50°C]; NRB N4, NRX N4
<60 sec @ -49°F [-45°C]
Angle of Rotation off (default)
adaptation Valve Body Inches DN [mm] A B C
Override control* min position = 0% B329-B331 1¼” 32 3.96” [100.6] 2.27” [57.7] 2.14” [54.3]
mid. position = 50% B338-B341 1½” 40 4.39” [111.6] 2.51” [63.7] 2.40” [61.1]
max. position = 100% B347-B352 2” 50 4.90” [124.5] 2.73” [69.5] 2.74” [69.7]
(0° is spring return position)
Ambient temperature -22°F to 122°F (-30°C to 50°C)
with heater -49°F to 122°F (-45°C to 50°C)
Storage temperature -40°F to 176°F (-40°C to 80°C)
Noise level ≤40dB(A) motor @ 150 seconds, run time dependent
Agency listings † cULus acc. to UL60730-1A/-2-14, CAN/CSA E60730-
1:02, CE acc. to 2004/108/EC & 2006/95/EC
Weight 9.7 lbs. (4.4 kg), 10 lbs. (4.5 kg) with switches
Programmed for 70 sec motor run time. At 150 sec motor run time, transformer sizing
is 8.5 VA and power consumption is 6 W running / 3 W holding.
AFRB24-MFT-S N4, AFRB24-MFT-S N4H, AFRX24-MFT-S N4,

AFRX24-MFT-S N4H
109
AFRB24-MFT N4, AFRB24-MFT-S N4, AFRB24-MFT N4H, AFRB24-MFT-S N4H
AFRX24-MFT N4, AFRX24-MFT-S N4, AFRX24-MFT N4H, AFRX24-MFT-S N4H
NEMA 4, Proportional, Spring Return, Direct Coupled, 24V, Multi-Function Technology®
Accessories
W399_08
NOTE: When using AFRB24-MFT N4, AFRB24-MFT-S N4, AFRB24-MFT N4H, AFRB24-MFT-S N4H
AFRX24-MFT N4, AFRX24-MFT-S N4, AFRX24-MFT N4H, AFRX24-MFT-S N4H actuators, only use
accessories listed on this page. For actuator wiring information and diagrams, refer to Belimo
Wiring Guide.
The actuator must provide proportional damper control in response to a 2 to 10 VDC or, with the
addition of a 500Ω resistor, a 4 to 20 mA control input from an electronic controller or positioner.
The actuators must be designed so that they may be used for either clockwise or counterclockwise
fail-safe operation. Actuators shall use a brushless DC motor controlled by a microprocessor and
be protected from overload at all angles of rotation. Run time shall be constant, and independent of VDC/4-20 mA
torque. A 2 to 10 VDC feedback signal shall be provided for position feedback. Actuators shall be
cULus Approved and have a 5 year warranty, and be manufactured under ISO 9001 International
W399_08
Quality Control Standards. Actuators shall be as manufactured by Belimo.
Wiring Diagrams

Actuators may be connected in parallel if not mechanically linked. Power
consumption and input impedance must be observed.

PWM
W399_08
Control signal may be pulsed from either the Hot (source) or the Common
5 (sink) 24 VAC line.
For triac sink the common connection from the actuator must be connected
9 to the hot connection of the controller.

connection. On/Off Control

W399_08

perform these tasks. Failure to follow all electrical safety precautions when exposed to
live electrical components could result in death or serious injury.
Floating Point Control

W600_AFRB_AFRX_N4
GK-AF-NF N4H 24V heater
NEMA 4 Heater
AFB24-MFT-S N4
AFRB24-MFT-S N4H
AFR$X24-MFT-S N4
AFRX24-MFT-S N4H
Auxiliary Switches
110
AFRB24-5-14, AFRB24-S-5-14 Actuators, On/Off
Dimensions
D1378
D
I
C
B
E F A
Models AFRB, AFRX

AFRB24-5-14
AFRB24-S-5-14 Nominal Top
Pipe Flange Height
Technical Data Size Design
Power supply 24 VAC ± 20% 50/60 Hz A B C
24 VDC +20% / -10% B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4]
holding 2.5 W B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1]
Transformer sizing 7.5 VA (class 2 power source) B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9]
AFRB24... 3 ft., 18 GA appliance cable, 1/2" conduit
connector
AFRX24... 3 ft. [1m], 10 ft. [3m] or 16 ft. [5m] 18 GA
Control on/off
< 60 seconds @ -22°F [-30°C]
Manual override 5 mm hex crank (3/16" Allen), supplied
Housing NEMA 2, IP54, Enclosure Type2
2004/108/EC & 2006/95/EC
AFRB24-S, AFRX24-S
111
AFRB24-5-14, AFRB24-S-5-14 Actuators, On/Off
Wiring Diagrams
W063_AFB(X)
1 Provide overload protection and disconnect as required. Line 1 Common

Volts 3
CAUTION Equipment Damage! 2 + Hot
2
AFB24, AFB24-S
Actuators may also be powered by 24 VDC. AFX24, AFX24-S 2
3
4 On/Off wiring for AFRB24, AFRX24
AFRB24-S and AFRX24-S incorporates two built-in auxiliary switches:
W064_AFB(X)_-S
+10°, one is adjustable 10° to 90°. 1 Provide overload protection and disconnect as required.
2 must be observed.
connection. 3 Actuator may also be powered by 24VDC.

AFB24-S
AFX24-S
Auxiliary Switches for AFRB24-S, AFRX24-S

W063
112
AFRBUP-5-14, AFRBUP-S-5-14 Actuators, On/Off
Dimensions
D1378
D
I
C
B
E F A
Models AFRB, AFRX

AFRBUP-5-14
AFRBUP-S-5-14 Nominal Top
Pipe Flange Height
Technical Data Size Design
Power supply 24 to 240 VAC -20% / +10%, 50/60 Hz A B C
24 to 125 VDC +10%
B6250 2½" [65] 7.50" [190.5] 5.50" [139.7] 8.10" [205.4]
holding 3.5 W B6300 3" [80] F05 8.00" [203.2] 6.60" [167.6] 8.40" [213.1]
Transformer sizing 7 VA @ 24 VAC (class 2 power source) B6400 4" [100] 9.00" [228.6] 8.30" [210.8] 9.30" [235.9]
8.5 VA @ 120 VAC
18 VA @ 240 VAC
AFRBUP... 3 ft., 18 GA appliance cable, 1/2" conduit
connector
AFRXUP... 3 ft. [1m], 10 ft. [3m] or 16 ft. [5m] 18 GA

Control on/off
Angle of rotation 95° (adjustable with mechanical end stop, 35°
to 95°)
< 60 seconds @ -22°F [-30°C]
Manual override 5 mm hex crank (3/16" Allen), supplied
Housing NEMA 2/IP54, Enclosure Type2
2004/108/EC & 2006/95/EC
AFRBUP-S, AFRXUP-S
113
AFRBUP-5-14, AFRBUP-S-5-14 Actuators, On/Off
A
Wiring Diagrams
W066_AFB(X)UP

3 No ground connection is required.

4 AFRBUP-S and AFRXUP-S incorporates two built-in auxiliary switches: AFBUP, AFBUP-S
AFXUP, AFBUP-S
+10°, one is adjustable 10° to 90°. A
On/Off wiring for AFRBUP, AFRXUP
W067_AFB(X)UP-S
connection. Wht
Blk
AFBUP-S
AFXUP-S

Auxiliary Switches for AFRBUP-S, AFRXUP-S
114
GKRB24-3-5-14 Actuators, On/Off, Floating Point, Fail-Safe
Dimensions
D1379
D
I C
B
E F A
GKRB, GKRX
Nominal Top
Pipe Flange Height
Models Body
Size Design
Diameter Length
GKRB24-3-5-14
A B C
B6400 4” [100] 9.00" [228.6] 8.30” [210.8] 9.30” [235.9]
Technical Data B6500 5" [125] 10.00" [254] 10.30" [261.6] 10.50" [266.4]
F05
Control on/off, floating point B6600 6" [150] 11.00" [279.4] 12.50" [317.5] 11.70" [296.9]
24 VDC ± 10%
holding 3 W
Input impedance 100 kΩ (0.1mA), 500 Ω, 1500 Ω (floating
point, on/off)

Running time running 150 seconds
fail-safe 35 seconds
2004/108/EEC and 2006/95/EC
115
GKRB24-3-5-14 Actuators, On/Off, Floating Point, Fail-Safe
Electrical Installation Wiring Diagrams

T ~
Wiring diagram
– +
Note DC 0 ... 10 V
Y
• Connect via safety isolation transformer. !
• Parallel connection of other actuators possible.
U DC 2 ... 10 V
Note performance data for supply.
1 2 3 5
observed.
Cable lengths
~ C
Y U
T
L2 Position feedback cannot be used with Triac sink controller.

Ltot

L1 5 or the Common (sink) 24 VAC line.
Note
When several actuators are connected in parallel,
the maximum cable length must be divided by the 1 2 3 5 Contact closures A & B also can be triacs.
number of actuators. A 8 A & B should both be closed for triac source and open for triac sink.
N L For triac sink the common connection from the actuator
AC 230 V
C
Y U
T
AC 24 V

connection.
L1 WARNING Live Electrical Components!
Note During installation, testing, servicing and troubleshooting of this product, it
There are no special restrictions on installation if 1 2 3 5 may be necessary to work with live electrical components. Have a qualified
the supply and data cable are routed separately. A licensed electrician or other individual who has been properly trained in
handling live electrical components perform these tasks. Failure to follow all
Cable colors: Cross section Max. cable length Example for DC electrical safety precautions when exposed to live electrical components could
1 = black L2 Ltott = L1 + L2
2 = red T
/
~
AC DC result in death or serious injury.
3 = white
5 = orange 0.75 mm2 <30 m <5 m 1 m (L 1) + 4 m (L 2)
1.00 mm2 <40 m <8 m 1 m (L 1) + 7 m (L 2)
A = Actuator 1.50 mm2 <70 m <12 m 1 m (L 1) + 11 m (L 2)
W399_10
C = Control unit 2.50 mm2 <100 m <20 m 1 m (L 1) + 19 m (L 2)
L1 = Belimo connecting cable, 1 m (4 x 0.75 mm2)
L2 = Customer cable A = Actuator
Ltot = Maximum cable length C = Control unit
L1 = Belimo connecting cable, 1 m (4 x 0.75 mm2)

On/Off control
W399_10
116
GKRX24-MFT-5-14 Actuators, Multi-Function Technology, Fail-Safe
Dimensions
D1379
D
I C
B
E F A
GKRB, GKRX
Nominal Top
Pipe Flange Height
Size Design
Models A B C
GKRX24-MFT-5-14 B6400 4” [100] 9.00” [228.6] 8.30” [210.8] 9.30” [235.9]
B6500 5" [125] 10.00" [254] 10.30" [261.6] 10.50" [266.4]
Technical Data F05
B6600 6" [150] 11.00" [279.4] 12.50" [317.5] 11.70" [296.9]
24 VDC ± 10%
holding 3 W
10 ft. [3m], 16 ft. [5m]
Feedback output 2 to 10 VDC, 0.5 mA max, VDC variable

Input impedance 100 kΩ (0.1 mA, 500 Ω)
1500 Ω (PWM, floating point , on/off)
fail-safe 35 seconds
Housing material UL94-5V (flammability rating)
2004/108/EEC and 2006/95/EC.
117
GKRX24-MFT-5-14 Actuators, Multi-Function Technology, Fail-Safe
Wiring Diagrams
W399_08

observed.

Control signal may be pulsed from either the Hot (source) VDC/4-20 mA
W399_08

connection.
PWM
W399_08
During installation, testing, servicing and troubleshooting of this product, it
may be necessary to work with live electrical components. Have a qualified
licensed electrician or other individual who has been properly trained in
handling live electrical components perform these tasks. Failure to follow all
electrical safety precautions when exposed to live electrical components could

On/Off control
W399_08
118
Accessories
CCV-EXT-KIT, CCV and PICCV Valve Neck Extension Kit
Application
The CCV-EXT-KIT can be used with most CCV’s* and PICCV in order
to achieve a large clearance over the pipe. The Extension Kit will
D165
provide an additional 2” of space between the top of the valve and the
base of the actuator. bracket is made from aluminum and is not
intended as a thermal block.
– Extension kit will be automatically assembled with any
Flanged CCV assembly.
Technical Data
Extension Height 2"
Total Weight 0.7 lb
Material
Extension Housing Aluminum - Anodized
Shaft Stainless Steel
Threaded Hardware Stainless Steel
Bearing Oilite® Bearing
Retaining Clip Stainless Steel
Available for Spring TR LRB (X) ARB (X) TF LF AF
and Non-Spring
Extension Bracket
Actuators
CCV-EXT-Kit
• • • • • •
* Cannot be used with N4 actuators.
* Available for previous NF assemblies.
* CCV-EXT-KIT cannot be used with any valve smaller than the
B212(B) and B312(B).
* For use with B2 and B3 series only. Cannot be used with B6 series.
2"
1.65" 1.65"
119
Accessories
ZS-CCV... New Characterized Control Valve Weather Shield
Application
The ZS-CCV... weather shield provides moderate protection for valves
which are mounted outdoors. This product is designed as a water tight
enclosure. The housing allows easy mounting over the actuator, while
allowing easy viewing of the actuator in operation. Weather shield for
PICCV/CCV to provide protection for actuators in outdoor applications.
Specifications
Cover PETG with UV resistant smoke tint
Perimeter Gasket Silicon Rubber
Rubber Gasket Silicon Rubber
Spring Clips Stainless Steel
Temperature limitations: -22˚F to 122˚F (-30˚C to 50˚C)
Plate (ZS-CCV-100) Aluminum
Plate Galvaneal w/black powder coat
Part Number Actuator

ZS - CCV - 90 LF, AF
ZS - CCV - 100 LRB(X), ARX
ZS - CCV - 110 AFRB(X)
L W H
16.25” [413] 8.75” [222] 4.5” [114]
Parts List
Cover including Rubber Perimeter Gasket, Rubber Gasket
Back Plate

Anti-Rotation Post with screw and lock washer
Valve Gasket
Assorted Cap plugs for unused holes
Screws AF - 2 bolts with nylon insert locking nuts

LRB(X), ARX - 1 screw, 1 washer
No weather shield available at this time for the TF and TR actuators.

Designed for NEMA 4 specifications.
* Cannot be used with B6 series.
120
Accessories
Auxiliary Switches S1A, S2A
For non-spring return direct-coupled actuators
Application
The S1A and S2A auxiliary switches are used to indicate when a
desired position of a valve is reached or to interface additional
controls for a specific control sequence.
Operation
The S1A and S2A auxiliary switches are mounted onto the direct coupled
actuator. The switches are modular units that mount directly onto LR and
AR type actuators and are locked into place by guiding grooves on the
sides of the actuator.
A driver disk is attached to the actuator handle and offers direct
transmission of the actuator position to the micro switch cams. The
switching points can be set over the full scale of 0 to 1 simply by
adjusting the slotted discs.
Types
S1A 1 SPDT 3 ft, 18 GA Appliance Cable
S1A/300 1 SPDT 6 ft, 18 GA Appliance Cable
S2A 2 SPDT 3 ft, 18 GA Appliance Cable

Technical Data S1A S2A

Number of switches 1 SPDT 2 SPDT
Weight 4.6 oz [130 g] 6.0 oz [170 g]
Switching capacity 3A (0.5A), 250 VAC
Switching point adjustable over full rotation (0° to 95°)
Pre-setting with scale possible
Ambient temperature -22°F to 122°F [-30°C to +50°C]
Housing NEMA 2 / IP54
Housing rating UL94-5VA

Agency listings cULus acc. to UL60730-1
CE according to 73/23/EEC
Wiring Diagram
Mounting Instructions
1. Press down the manual override button and rotate the actuator
fully counter clockwise.
2. Place the switch/potentiometer adaptor onto the hex shaft of the
handle which is in the center of the valve/actuator coupling.
3. Slide switch onto the actuator using the actuator guiding grooves
on the sides of the actuator.
4. Check for correct mating of the adaptor to the switch.
5. Adjust switch dials as necessary.
121
Accessories
Feedback Potentiometer P...A
For the non-spring return direct-coupled actuators
Application
The P…A feedback potentiometers are used with LR and AR actuators
to provide a resistive signal which varies with valve position.
The P…A units are applied with commercial proportional temperature
controllers to provide feedback of the valve position, or with electric or
electronic meters to provide position indication. The signal can also be
used as a positioner for parallel operation of multiple actuators.
Operation
The P…A feedback potentiometers are mounted onto the direct coupled
actuator. The switches are modular units that mount directly onto LR and
AR type actuators and are locked into place by guiding grooves on the
sides of the actuator.
A driver disk is attached to the actuator handle and offers direct
transmission of the actuator position to the micro switch cams.
Types
P140A Feedback Potentiometer 140 Ω
Technical Data P...A

Resistance values as above
Output 1W
Tolerance ± 5%
Linearity ± 2%
Resolution min. 1%
Residual resistance max. 5% on both sides
Electrical connection 3 ft, 18 GA appliance cable
½" conduit connector

Housing NEMA 2 / IP54
Housing rating UL94-5VA
Agency listings cULus acc. to UL60730-1
CE according to 73/23/EEC
Weight 4.6 oz [130 g]
Mounting Instructions
1. Press down the manual override button and rotate the Wiring Diagram
actuator fully counter clockwise.
2. Place the switch/potentiometer adaptor onto the hex shaft of the
handle which is in the center of the valve/actuator coupling.
3. Slide switch onto the actuator using the actuator guiding grooves
on the sides of the actuator.
4. Check for correct mating of the adaptor to the switch.
5. Adjust switch dials as necessary.
122
Wiring Accessories
Protective Terminal Cover
For the non-spring return direct-coupled actuators
Application
Belimo non-spring return actuators with terminal strips are can be
converted from NEMA 1/IP20 to NEMA 2/IP54 using the protective
terminal cover ZS-T.
The ZS-T terminal cover accessory consists of:

• Terminal Cover
• Conduit Fitting
• Rubber Seal for Wire Diameter 4-6
• Rubber Seal for Wire Diameter 6-8
Terminal
Cover Conduit
Fitting
Rubber
Seals
Mounting the Terminal Cover

1. Attach terminal cover to actuator, if not done already.
2. Slide the conduit fitting and correct size rubber seal onto wire.
3. Wire up actuator using the terminal strips.
4. Fit rubber seal into slot of terminal cover.

5. Shut terminal top and screw on conduit connector.
123
MFT Standard Configuration
Configuration Control Motion

(Substitute ‘V’ for ‘P’ for Code
NV[F] actuators) Input Range Position Feedback Running Time† Torque % Adaptation
P-10001 A01 2.0 to 10.0 VDC 2.0 to 10.0 VDC 150 100 Manual
Voltage
P-20001 W01 0.59 to 2.93 sec. 2.0 to 10.0 VDC 150 100 Manual
PWM
P-30001 F01 Floating point 2.0 to 10.0 VDC 150 100 Manual
Floating Point
P-40001 J01 On/Off 2.0 to 10.0 VDC 75 100 Manual
On/Off


*P-10001 is the default configuration.
Example: AF24-MFT US is the basic model. Add the P… pre-set MFT configuration number and list price to the actuator when ordering, as needed.
Note: V-codes used for NV…Series actuator. All other MFT actuators use P-codes.
Note: Most popular configurations available at no additional cost.
Note: If the configuration needed is not listed, please fill in pg. 112 or call Belimo Customer Service at 800-543-9038.
Note: For Non-Spring Return Actuators the 3-digit code can be used in place of the P… pre-set MFT configuration number.
124
MFT Programming Codes, Flexible Products
PRODUCTS
Base Actuator Angle of
MODEL Control Input Feedback Running Time Power Supply VA Rating Weight (lb)
Codes Rotation/Stroke
LRX24-3 LR000 On/Off, Floating Point — 95 (Default) 95 deg 24 VAC/DC 3 1.08
LRX24-SR LR030 2-10 VDC (4-20mA*) — 95 (Default) 95 deg 24 VAC/DC 3 1.08
45 in-lb [5 Nm]
LRX24-PC LRXX0† 0-20 V Phasecut 2-10 VDC 95 (Default) 95 deg 24 VAC/DC 3 1.08
LRX24-MFT LR100 2-10 VDC (Default) 2-10 VDC 150 (Default) 95 deg 24 VAC/DC 3 1.08
LRX24-MFT95 LRXX0† 0 to 135 Ohm 2-10 VDC 150 (Default) 95 deg 24 VAC/DC 3 1.08
LRX120-3 LR060 On/Off, Floating Point — 95 (Default) 95 deg 120-240 VAC 3 1.08
LRX120-SR LR450 2-10 VDC (4-20mA*) — 95 (Default) 95 deg 120-240 VAC 3 1.08
ARX24-3 AR000 On/Off, Floating Point — 95 (Default) 95 deg 24 VAC/DC 5 1.08

180 in-lb [20 Nm]
ARX24-SR AR030 2-10 VDC (4-20mA*) — 95 (Default) 95 deg 24 VAC/DC 5 1.08

ARX24-PC ARXX0† 0-20 V Phasecut 2-10 VDC 95 (Default) 95 deg 24 VAC/DC 5 1.08
ARX24-MFT AR100 2-10 VDC (Default) 2-10 VDC 150 (Default) 95 deg 24 VAC/DC 5 1.08
ARX24-MFT95 ARXX0† 0 to 135 Ohm 2-10 VDC 150 (Default) 95 deg 24 VAC/DC 5 1.08
ARX120-3 AR060 On/Off, Floating Point — 95 (Default) 95 deg 120-240 VAC 5 1.08
ARX120-SR AR450 2-10 VDC (4-20mA*) — 95 (Default) 95 deg 120-240 VAC 5 1.08
† For correct code please call Belimo Customer service 800-543-9038
Configuration Control Motion

(Substitute ‘V’ for ‘P’ for Code
NV[F] actuators) Input Range Position Feedback Running Time† Torque % Adaptation
Voltage
PWM
Floating Point
P-40001 J01 On/Off None 75 100 Manual
On/Off
P-40003 J03 On/Off None 75 100 Manual

*P-10001 is the default configuration.
125
Custom MFT Configuration Order Form
FAX: USA Toll Free 1-800-228-8283
#1 Select an Actuator
(use one sheet for each unique actuator/configuration)
Name _______________________________________________________________________________
Quantity Quantity
❑ AF24-MFT US ______ ❑ AMX24-MFT ______
Company ____________________________________________________________________________
❑ AF24-MFT-S US ______ ❑ AMX24-MFTX1 ______
❑ NF24-MFT US ______ ❑ NMX24-MFT ______
Address _____________________________________________________________________________
❑ LF24-MFT US ______ ❑ NMX24-MFTX1 ______
❑ LF24-MFT-S US ______ ❑ LMX24-MFT ______
City_______________________________________ State _____________Zip _____________________
❑ AF24-MFT95 US ______ ❑ LMX24-MFTX1 ______
❑ NV24-MFT US ______ ❑ LRX24-MFT ______
Phone_____________________________________ Fax_______________________________________
❑ NVF24-MFT US ______ ❑ GMX24-MFT95 ______
❑ NVF24-MFT-E US ______ ❑ AMX24-MFT95 ______
Email _____________________________________
❑ NVFD24-MFT US ______ ❑ NMX24-MFT95 ______
❑ NVFD24-MFT-E US ______ ❑ LMX24-MFT95 ______
FIELD LABELING: LBL-MFT
❑ GMX24-MFT ______ ❑ LHX24-MFT ______
❑ GMX24-MFTX1 ______ ❑ LUX24-MFT ______ ❑ Custom configuration labels required
1-3/8” X 1-¼” orange labels preprinted to your specifications 12 label sets per sheet.
(-S=Auxiliary Switch) Includes configuration code and wiring labels.
#2 Create a Custom Configuration

Deactivated (Default) The following settings - refer to the full angle of rotation of 95º.
The following settings - are automatically adapted to the effective

Activated mechanical angle of rotation.
1 Angle of rotation setting
Manual triggering by pressing the push button twice.
Automatic triggering each time the unit is powered up

or by pressing the push button twice.
VDC PWM Floating Point On/Off
2 – 10 0.2 to 5.0 seconds

0 – 10 0.1 to 25.5 seconds
2 Control Types
Variable 0.59 to 2.93 seconds
Start . Variable

Stop . Start .
Stop .
Position Feedback U DC 2...10 V (Default)
3 Feedback Signals U5 Position Feedback U DC 0...10 V
Position Feedback U Start DC . V (0...8 V) The finish must

be at least 2 V
Finish DC . V (2...10 V) above the start!
150 seconds (Default)
Running time seconds (75...300 seconds) (in 5 second increments)

Note: The sound power level [dB(A)]
4 Running Time increases when the running time LM 35…150 seconds
is below 150 seconds. NM 45…170 seconds
AM 90…300 seconds
GM 90…300 seconds
Others 75…300 seconds
5 Override control and Min. (min. position) = % (0...100%) (beginning of working range) default 0
electronic angle of ZS (intermediate position) = % (0...100%) (0% = Min.; 100% = Max.) default 50
rotation limiting Max. (max. position) = % (0...100%) (end of working range) default 100
126

CCV Technical Document

Uploaded by

Copyright:

Available Formats

You might also like

CCV Technical Document

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CCV Technical Document

Uploaded by

Copyright:

Available Formats

Characterized Control Valves™ (CCV)

Features and Benefits

EQUAL PERCENTAGE VALVE CHARACTERISTIC

● Thermal isolating adapter between ● Vent holes reduce

* Designed for service life of over 100,000 full cycles.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA

COORDINATED MOTORIZED OPERATION Flow Characteristics of Conventional Ball Valves

P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

Service: Chilled/hot water, 60% glycol

Mixing* (Not for use in change over applications)

Desirable Equal Percent Flow and resulting

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

Cv Pressure Drop Across the Valve

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA

Cv Pressure Drop Across the Valve

GPM = Cv x ∆p * = Models with no characterizing disc.

P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA

TR24-3-T US Power to pin 2 will Power to pin 2 will

Will spring closed A to AB Will spring closed A to AB

NO/FO Valve: Open A to AB NO/FO Valve: Open A to AB

GENERAL WIRING INSTRUCTIONS

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA

3-way Characterized Control Valves™ (Belimo B3 Series)

The A-port must

The A-port must be piped to the coil to maintain proper control.

OPERATION/INSTALLATION – CORRECT PIPING

P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

Diverting* (Not for use in change over applications)

Diverting* (Not for use in change over applications)

*LR and AR include 120-240 VAC

3 For MFT Orders Only - Select Programming Code

B209+LRX24-MFT NO Tagging (if needed)

Non Fail-Safe Models

5 Complete Ordering Example: B209+LRX24-MFT

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA

B6 250 S -070 +GRX 24 -MFT

*AR includes 120-240 VAC

3 For MFT Orders Only - Select Programming Code

P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

Non Fail-Safe Models

5 Complete Ordering Example: B6250S-070+GRX24-MFT

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA

Valve Nominal Size Type Suitable Actuators

Valve Nominal Size Dimensions (Inches [mm])

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

* (Not for use in change over applications)

Valve Nominal Size Type Suitable Actuators

P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

Valve Nominal Size Dimensions (Inches [mm])

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

Valve Nominal Size Type Suitable Actuators

External leakage according to EN 12266-1:2003 46 2 50 B249

800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN

* (Not for use in change over applications)

Valve Nominal Size Type Suitable Actuators

P10419 - 09/13 - Subject to change. © Belimo Aircontrols (USA), Inc.

Valve Nominal Size Dimensions (Inches [mm])