Professional Documents
Culture Documents
The Thickness of Base Plate by The ASD.I Section Column Concrete
The Thickness of Base Plate by The ASD.I Section Column Concrete
The Thickness of Base Plate by The ASD.I Section Column Concrete
com
- the safety factor for the bending of steel: Wb = 1.6667 See Subch. F1 1)
- the safety factor for the shear of steel: Wv = 1.6667 See Subch. G1 1)
- the safety factor for the compression of concrete: Wc = 2.3077 See Subch. J8 1)
- the material of base plate steel: ASTM A36 ✓ See Table 2-5 1)
- the minimum yield stress: Fy = 36.00 ( ksi ) ✓
- the minimum tensile stress: Fu = 58.00 ( ksi ) ✓
- the material of HP-, M-, S-, W-shape: ASTM A992 ✓ See Table 2-4 1)
- the minimum yield stress: Fy = 50.00 ( ksi ) ✓
- the minimum tensile stress: Fu = 65.00 ( ksi ) ✓
Notes:
1)
ANSI / AISC 360 - 10 Specification for Structural Steel Buildings, AISC © 2010;
2)
AISC Steel Construction Manual, 14th Edition, AISC © 2011;
3)
AISC Steel Design Guide 1, Fisher J.M., Kloiber L. A. "Base Plate and Anchor Rod Design", 2nd Edition, AISC © 2006;
4)
Tolerances, variations and deviations shall be considered;
5)
Holes, welds and fasteners are not shown on the figure conditionally.
Spreadsheet V2016-3 bguzikov @ gmail.com
, P.E.
0 Date: 12/31/2016 Page №: 2 of 4
Address: Street, # Project: 00-11-22-33-44-55
0 Contract №: 2016-21
0 By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The thickness of base plate by the ASD.
E-mail: @gmail.com The I-section column (post) and the concrete foundation
0 at the axial compressive load. 1) , 2) , 3)
( The US customary units )
The initial data for the calculation and
the calculation's results:
- the base plate's required area: A(req) = ( Pa´Wc )/ ( 0.85´f 'c´( A2/ A1 )1/2 ) = 27.15 ( in2 )
- the nominal bearing strength of concrete: Pp = 0.85´f 'c´A1´( A2/ A1 )1/2 = 217.60 ( kips ) See Eq. J8-2 1)
- the allowable bearing strength of concrete: Pp/Wc = 94.29 ( kips ) See Chapter J8 1)
- the initial required base plate thickness: tp (req) = L´( 2´Wb´Pa/ ( Fy´B´N ) )1/2 = 0.3563 ( in ) See Eq. 14-7b 2)
Spreadsheet V2016-3 bguzikov @ gmail.com
, P.E.
0 Date: 12/31/2016 Page №: 4 of 4
Address: Street, # Project: 00-11-22-33-44-55
0 Contract №: 2016-21
0 By: M.M. Checked: N.N.
Phone: +1 - 718 -
Fax: +1 - 718 - The thickness of base plate by the ASD.
E-mail: @gmail.com The I-section column (post) and the concrete foundation
0 at the axial compressive load. 1) , 2) , 3)
( The US customary units )
The calculation's results of the base plate thickness
based on the conditionally isolated cantilevered strip
of unit width:
- the minimum shear stress of base plate material: Fs = 0.5774´Fy = 20.79 ( ksi )
- the inequality for the combined strength: 0.2800 < 1.0000 28%, OK