Professional Documents
Culture Documents
Haier Hw80, Hw100, Hw120-b14979 979 Series Washing Machine SM
Haier Hw80, Hw100, Hw120-b14979 979 Series Washing Machine SM
Contents
Chapter 1 General Information ______________________________________________ 4
H W 80 B 14 979
Model series
Max spin speed-1400rpm
frequency conversion
80:Max Wash Load-8kg
100:Max Wash Load-10kg
120:Max Wash Load-12kg
Washer
Haier
5
979
DD motor
6
979
2-2. Specification
220-240V/50Hz
10
500
8 10 12
1400
14
1800
54 54 54
69 69 69
DO ...
... Make sure that the transportation bolt(T1,T2&T3) are removed.
●
... Hold the plug and not the electric cable when unplugging the
power supply.
... Make sure that the fuses in the power circuit are rated for
15A (European type)/ 16A (Israel type).
... Keep away from heat sources and direct sun light to prevent
plastic and rubber components from aging.
... Make sure that the power cord is not caught under or in the
appliance and avoid damage to the power cable.
... Check that hose joints and connections are firm and no water
●
can leak. If joints are loose or there is leakage, turn off the
water supply and refix. Do not use the washing machine until
the hoses are properly fixed.
DO NOT ...
... Touch or use the appliance when barefoot or with wet or damp
hands or feet.
... Use flammable detergent or dry cleaning agent.
... Use any flammable sprays in close vicinity to the appliance.
... Remove or insert the plug in the presence of flammable gas.
... Allow children or infirm persons to play with the appliance or
packing materials.
8
979
DO ...
... Pull up zips and fix loose threads to prevent the items from being
entangled. If necessary, put small items into a net bag or pillow.
... Turn off the machine after each wash program and switch it off at
the mains to save electricity and for safety. Wipe clean the lower
part of the porthole.
... Keep the door slightly open when the washing machine is not in
use to prevent formation of odours.
... Let the power cord be replaced by the manufacturer, his service
●
DO NOT ...
... Touch the washer door during the washing process - it gets hot!
... Place heavy objects or sources of heat or damp on top of the app-
liance.
... Hot wash foam rubber or sponge-like materials.
... Open the detergent distribution drawer during the wash cycle.
... Force the washer door open. The door is fitted with a self-lock device
and will open shortly after the washing procedure is ended. ●
... Open the washer door if the water level is visibly over the porthole.
... Cover the washing machine with plastic cover so that inside dampness
cannot be kept in. ●
9
979
5 6
Delay Temp.
4 3 2 1
4.3 Display
4-4 The display (Fig. 4-4) shows following information:
Delay Temp.
▶ Washing time
▶ End time delay
Stain removal Steam Extra Rinse Speed
If a button has multiple options, the desired option can Stain removal Steam Extra Rinse Speed
4-15 Speed
4.7 Child lock
Choosing a program and then start,touch button“ Spe-
Speed ed”and ”Start/Pause ”( Fig .4-15) for 3 seconds simulta-
neously to block all panel elements against activation,p-
anel display .For unlocking please Touch again the t-
wo buttons.The child lock indicator lights up when the
child lock works.feature is optional when the machine is
4-16 running.
The display shows cI oI- (Fig. 4-16) if a button will be
pressed, when the child lock is activated. The change
is not running.
12
979
3
2 Softener or care product
2
2
3 sanitizer 3)
• Yes, º Optional, / No
Stain removal
in kg in °C 1) in rpm
Extra Rinse
Preset
Steam
HW80-B14979
i-time
Delay
Programme HW100-B14979 selectable
HW120-B14979 range 1 2 3 Fabrics type
Cotton 8/10/12 * to 90 40 • º º Cotton 1400 •••• •
Synthetics 4/5/6 * to 60 40 • º º Synthetic or mixed 1200
fabric
/ •• • •
Duvet 4/5/6 * to 40 30 • º / Duvet 800 • / •• /
Machine-washable
Wool 2/2.5/3 * to 40 * • º / fabric made of wool
or with wool content
800 • / • • /
1
2.2.1
1 2
2 6 3
7 4
3
9
5
6
10
5 7
8
11
9
1 Worktop
2 Detergent / Softener / disin-
fectant drawer 1 Power cord plug
3 Drum door 2 Work top
4 Front panel 3 Water inlet valve
5 Adjustable feet (4 in all)
4 Power cord
6 Touch screen display 5 Back cover
7 Power button
6 Back cover screw
8 Rating plate
9 Drum 7 Transportation bolts
10 Sealing 8 Packing rods
11 Service fl 9 Cabinet
15
979
600
HW80-B14979:(H*W*D)mm=(850*595*460)mm
HW100-B14979:(H*W*D)mm=(850*595*530)mm
●
HW120-B14979:(H*W*D)mm=(850*595*600)mm
16
979
17
979
18
979
19
979
Cotton
Duvet
Outdoor
Synthetic
Mix
Wool
Cotton 20 ℃
Express 15’
Baby Care
Eco 40-60
Refresh
Delicate
Drum Clean
Spin
20
979
Appliance fails to • Programme is not yet started. • Check programme and start it.
operate. • Door is not properly closed. • Close the door properly.
• Appliance has not been switched on. • Switch the appliance on.
• Power failure. • Check power supply.
• Child lock is activated. • Deactivate child lock.
• Time delay is activated. • Deactivate time delay function.
• Pause button is pressed. • Deactivate pause mode.
Control panel is out • Child lock is activated. • Deactivate child lock.
of function
• No water. • Check water tap.
with water. • Inlet hose is kinked. • Check inlet hose.
• •
• Water pressure is too low. • Check water pressure.
• Door is not properly closed. • Close the door properly.
• Water supply failure. • Ensure the water supply
• Time delay is activated. • Deactivate time delay function.
• Start button in not touched. • Touch start button.
Appliance is draining • Height of drain hose is below 80 • Make sure that drain hose is
cm. properly installed.
• Drain hose end could reach into water. • Make sure the drain hose is not
in water.
Drainage failure • Drain hose is blocked. • Unblock drain hose.
• •
• Drain hose end is higher than 100 • Make sure that drain hose is
cm above floor level. properly installed.
Strong vibration while • Not all transportation bolts have • Remove all transportation
spinning. been removed. bolts.
• Appliance has no solid position. • Ensure solid ground and a lev-
elled position.
• Machine load is not correct. • Check load weight and balance..
Operation stops • Water or electric failure. • Check power and water supply.
before completing • Pause button is pressed. • Deactivate pause mode.
wash cycle.
Operation stops for a • Appliance displays error informa- • Consider display information.
period of time. tion.
• Problem due to load pattern. • Reduce or adjust load.
• Programme performs soaking cycle. • Cancel programme and restart.
Excessive foam floats • Detergent is not a appropriate • Check detergent recommen-
drum and/or deter- dations.
gent drawer. • Excessive use of detergent. • Reduce amount of detergent.
Automatic adjustment • Washing programme duration will be • This is normal and doesn‘t af-
of washing time. adjusted. fect functionality.
Spinning fails. • Unbalance of laundry. • Check machine load and laun-
dry and run a spinning pro-
gramme again. .
Strange sound • Appliance has no solid position. • Ensure solid ground and a lev-
elled position.
• Foreign m atters like coins or zip- • Ensure pockets are emptied of
pers hit the drum. keys, coins etc.
Parts of control • • It´s normal.
panel has higher
temperature.
Unsatisfactory wash- • Degree of pollution does not agree with • Select another programme.
ing result selected programme.
• • Choose the detergent acc. to the
degree of pollution and acc. to
Water temperature sensor Check the resistance of temperature sensor in heater also
F3 error the wire connection and fix.
Please check whether the tap is turned on, whether water
E4 Water Inlet error pre ssure is too low, or whether the water is cut o .
Check heater and wire connection.(Resistance of heater
F4 Heating system error.
should be around 30Ω)
Check wire connection and motor then fix.
F7 Motor system error
Water level in drum too 1. Check and fix the block, kink of water pressure switch.
E8 2.Check if water inlet valve can not stop when power off , if so,
high replace water inlet valve.
Water level sensor sensor Check if the wire connection to water level sensor is loosen
FA error and fix. If the problem still exit, change the water level sensor.
Check the PCB power lines and reactance lines ,make sure they
FC0 Communication bus error are well inserted .Error of PCB, need to change PCB
Motor driving module Check if the wire connections between control board and
FC1 driven boards are loosen and fix. If it is OK, check and change
communicating error control board or driven board.
Check if the wire connections between control board and
Motor driving module power
FC2 boards are loosen and fix. If problem still exist, change
communicating error control board and power boards.
Sub-switch continuously Open drain pump to drain,
Fb leaks for 10 seconds-error Shut down the machine.
The distribution of laundry Please ensure the washing machine is leveled and take out
UNB is unbalanced during spin- the laundry to make it loose, then put it back for spinning.
ning
CLR FLTR
Replace PC B
Check if the PCB communication lines are Make sure the communication lines are well
N
connected properly
inserted.
Check if the lights of the motor drive PCB Check the motor drive PCB power lines and
are shining. N
reactance lines,make sure they are well inserted.
Check if the lights of the motor drive PCB Check the motor drive PCB power lines and
are shining. N
reactance lines,make sure they are well inserted.
10-2
10-2-1
10-2-2
10-2-3
10-2-4
10-2-5
10-3.
1.Water heater
Heater
voltage 230V
5%
2.Drain pump
Drain pump
voltage 220-240V 50Hz
10-3.
3.Water inlet valve voltage 220V 50/60Hz
Door lock
4.Door lock voltage 250V
Amp. 16(6)A
resistance 1-3:
2
1 3
2 2
3 3
1 1
10-3.
Motor
5.Motor voltage 220V,50/60Hz
resistance 5% 22
2
3
1 1
2 2
3 3
P171
1 2
3
Attention:
1. Pull out the plug before disassembly.
2.Keep the wire away from sharp stuff,avoid any brokage of isoluation protector
therefore avoid creepage.
3.Collect screws,accecoories and keep them in difference place,avoid missing
parts so that the technicians could reassemble them.
1 Screw driver
2 Plier
Spanner
3 Sleeve 13/15
4 Multimeter
Dismantle counterweight
Sincere Forever
Haier Group
Haier Industrial Park, No.1, Haier Road
http://www.haier.com