Professional Documents
Culture Documents
ATPJET S Series INKJET PLOTTER MANUAL
ATPJET S Series INKJET PLOTTER MANUAL
ATPJET S Series INKJET PLOTTER MANUAL
USER MANUAL
MANUAL OF ATPJET
NOTICE
The ATPJET product and its control center are subject to change/improve without notice.
but not limited to, the implied warranties of merchantability and fitness for a particular
purpose.
ATPINDUSTRIAL is not responsible for any errors in this document any incidental or
Preface
Thanks for selecting New Power ATPJET High-Speed Intelligent Inkjet Plotter!
New Power ATPJET High-Speed Intelligent Inkjet Plotter series are based on a paper
feeding system driven by roller friction. It can be used to draw and cut complex graphics
and texts, the material including computer paper, barley paper and so forth (thickness
ranging from 30g-60g). New Power ATPJET High-Speed Intelligent Inkjet Plotter series
are beautiful and elegant in design and also achieve high precision, high speed, stable
performance and compatibility (compatible with HPGL). It can work with nearly all of the
Before you use the plotter, please read the user manual carefully and insure that you
If you have any questions, please contact with local dealer or local office for support.
(The plotter and output center software gain huge update space in response to customer's
customized requirement. We will increase and improve functions of machine and software
without notice. If any change in this manual, there will be no notice. Please call
Safety Regulations:
Please read the following guidance carefully before using the ATPJET High-Speed
Put the plotter on the level ground to avoid needless troubles; when the ground is slant,
Assembly the plotter and adjust stand feet height, until the whole machine reaches the
level state.
Please connect the plotter with power supply according to rated voltage and don't
connect the plotter to the socket without stable voltage, as the unstable power supply
will lead to reduce plotter performance and even burn down power supply board; please
The power supply plug should be connected with ground line. Don't remove the pin on
top of the plug to ensure good ground connection with plotter. If the machine isn't
connected to the ground, it will result in electric discharge by too much electric charge
Avoid connecting the plotter to the same power outlet with high-power equipments. If it
is connected to the same electric plug with other equipments in parallel, please confirm
that required power of these equipments does not exceed the maximum electric current
please pull plug out of the power outlet, if not using the plotter for long time;
Don't drop liquids into plotter, otherwise the plotter would be short-circuited and the
MANUAL OF ATPJET
Don’t fix or dismantle the plotter unless the user manual has an elucidation;
Don’t plunge your hand into the plotter to handle the small ink vehicle and inner spare-
parts of machine;
Whether you are familiar with the New Power ATPJT High-Speed Intelligent Inkjet
Plotter series or not, please read the following items carefully before operate the machine:
1 Environmental Condition:
(1). Working temperature for the plotter is 0-35 degree; don’t put or use the machine in
(2). Working humidity scope of plotter under the normal temperature is 20%-80%;
don’t put plotter under the moist and dusty places. Once vapor coagulates inside of
the plotter, the dust enters into the plotter, which will result in short-circuit or poor
(3). Avoid the strong electromagnetism interference and don’t put magnetic things by
2 Other Notice
1. Don't move the cartridge holder by hand; otherwise it will damage plotter.
2. Do not twist the retaining nut in the cartridge holder, except handing ink cartridge.
4. Please ensure the switch is off before you access or cut off power supply.
5. Please place the dust proof cover over the plotter to prevent the dust entering into the
6. Avoid turning on and off the plotter frequently in order to prevent performance of
electronic components.
MANUAL OF ATPJET
7. In the process of plotting, don’t rely your body on machine or put hand on the rail.
8. If signal transmission line needs to be connected or adjusted, please confirm that the
As our official catalog and you can contact with our local dealer for more detail.
2 System Requirements
format language
1. 1 Pc of main body □
2. 2 Pcs of stand □
3. 1 Pc beam □
4. 1 Pc power line □
7. 1 Pc delivery rod □
14. An installation CD □
(2) Fix the stand in position, then put mainframe on stand smoothly and tighten the screws.
(3) Use a leveler to test if the mainframe is in level; if any deviation, adjust feet cup under
1. Mainframe 2. Stand 3. Crossbeam 4.Take up paper bar 5.Paper bar 6. Dancer Bar(front)
7. Dancer bar (Back) 8. Top cover 9 Orbit for dancer bar 10 USB Cable 11 Paper holder
(2) Open the package of ink cartridge, hold the ink cartridge and shake it several times
to prevent ink deposit. Then put the ink cartridge into the cartridge clip (as shown in
picture) with attention to put the cartridge into the 45-degree oblique direction, from the
top to the inner. Do not put it in right position just once and the action should be gentle to
avoid damaging the internal electronics components. Finally, buckle ink cartridge cap.
Step 1:
Step 2:
MANUAL OF ATPJET
Step 3:
(3)Change and pick off the ink cartridge by opposite way as shown above. (Please
(Paper advance)
towards left
Pause key: pause the current scanning and printing; in a suspended state and
computer, and then unzip the file; open the folder , you will see an
icon
Double click this icon to perform following installation steps: (as shown in picture)
MANUAL OF ATPJET
This step is to selecting the number of cartridges: It is based on your machine model
and cartridge number.
MANUAL OF ATPJET
Notice that there is a tip on the bottom right of display indicating the discovery of new
Double click this icon on the desktop, under normal circumstances; you will see
the following screen:
MANUAL OF ATPJET
Medium.
喷头 1 Cartridge 1
喷头 2 Cartridge 2
Before revision, the left-right deviation appears when scanning, which has
specifications (as shown below)
Tips: Correct through above steps, but the followings still appear. We can solve
these troubles through check;
MANUAL OF ATPJET
(Solution) Loosen the screw fore-and-aft ink cartridge, adjust the position of
ink cartridge group to achieve the correct position (shown as below)
MANUAL OF ATPJET
2. Use the plotter to revise the size. The garment CAD software keeps the default value.
MANUAL OF ATPJET
(shown as below)
Attention: 1) When you are in the process of parameter setting, please be sure to use
standard or the same scale that you recognize (as some scale also has a very big error);
2) If you still cannot reach your required precision in 1000mm scale range,
please expand the scale. For example, you can draw a 10000mm (10 meters) marker and
carry on actual measurements to calibrate the accuracy and correct its precision.
X, Y value must be filled according to 1000mm and actual measured value. Although this
will waste some time, but it must reach your required precision!
MANUAL OF ATPJET
Printing directory
contains *PLT files created by garment CAD software.
standby the system will perform automatic printing , after receiving files; or
Toolbar Details:
Select the location where the file exists, click the icon 打 开 (open), the system will
Open control center, left click this button, click the button and the button will
be sunken, the control center will turn to automatic drawing status!
Then click the button again to cancel the automatic drawing status! After
this clik you can use the following one button or more buttons to manually line up
the plot file or single drawing: (Attention:Please click this button once more time to
Print pause 暂停, print stop 停止and print cancel 取消 can be used by
This button is used to zoom in the image of selected files. Click it once to zoom
in images one time bigger in images list box, but the output effect won't be affected.
The
Introducti
on File
List Box
MANUAL OF ATPJET
Print mode offers four ways, selecting the most appropriate way
It can set the number of plotting files and display the number of
During the printing, you can know current print position through the
dynamic view.
Through above information, it can master the dynamic between the plotter and
computer in real time, as well as end time of file printing.
MANUAL OF ATPJET
When you face any problems during the use of plotter, please read below item
carefully in order to find the solution. If you cannot find solution, please contact with us,
The indicator light isn't on, which means the plotter isn't powered. Please check if
power cable is connected with AC socket of plotter, if the power touch is good, if it has
2 After turn on the machine cartridge holder running rightwards and cannot stop
Please check if the ink vehicle aligns with magnetic sensor, adjust the sensor,
Please check if the cartridge has run out, if the nozzle is blocked by dusty. We
1) Check if the plotter is placed on level ground (use horizontal regulator to adjust
4) Make sure the two paper pressing rods/dancer bars are in normal/correct shape.
We found due to some users use different version of the operation system(especially with
different language) our control center will install by default language( Chinese)
First you copy the control center from the Disk (check your computer operation system is
32bit/64bit
Then you unzip the install file /copy the file to your computer
Please rename the Chinese/wrong operation words to be English then it can set the
3. Click
5. The click
6. You will find English option
Click English. If your computer has no Chinese data and maybe the words can’t show
correctly please remember the button and operate as above you also can find the
English.
8. Rename the file delete all the Chinese or some words can’t appear correctly change to