Professional Documents
Culture Documents
BMW F10 3AG Retrofit Camera NBT
BMW F10 3AG Retrofit Camera NBT
Installation Instructions.
Rear View Camera Retrofit
BMW 5 Series Saloon (F10)
Installation instructions only valid for cars with the head unit high.
Installation time
The installation time is approx. 4.5 hours. If the video switch retrofit kit needs to be installed, the installation time
will be increased by approx. 1.5 hours. This may vary depending on the condition of the car and the equipment
in it.
The installation time shown does not include any time spent on programming/coding.
The calculation of the total costs for the programming time must be factored into the calculation of retrofitting costs
(no charges may be made through the warranty).
Important information
These installation instructions are primarily designed for use within the BMW dealership organisation and by
authorised BMW service companies.
In any event, the target group for these installation instructions is specialist personnel trained on BMW cars with
the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, wiring diagrams, servicing manuals and work
instructions, in a rational order, using the prescribed tools (special tools) and observing current health and safety
regulations.
If you experience installation or function problems, restrict troubleshooting to approx. 0.5 hours for
mechanical work and 1.0 hour for electrical work.
To avoid unnecessary extra work and/or costs, send an inquiry straight away to the technical parts support team via
the Aftersales Assistance Portal (ASAP).
Quote the following information:
- Chassis number,
- retrofit kit part number,
- a detailed description of the problem,
- any work already carried out.
Do not archive the hard copy of these installation instructions since daily updates are provided via ASAP!
Pictograms
Denotes instructions that draw your attention to dangers.
!
1
1
Ordering instructions
Control unit C is not part of the retrofit kit and must be ordered separately (see EPC for part number and details).
If four video sources are already installed in the car, see special equipment in the special equipment directory
shown below, a video switch AA must be retrofitted.
If the video switch retrofit kit is installed, video switch AA must be ordered separately (see EPC for part number
and details).
Section Page
1 Rear view camera parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Video switch parts list (cars with Apps, TV, night vision and DVD changer only) . . . . . . . . . . . . . . . . . . . . . . 5
3 Preparatory work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Video switch connection diagram (cars with Apps, TV, night vision and DVD changer only) . . . . . . . . . . . . 8
6 DVD changer/TV adapter cable connection diagram (only when video switch is installed). . . . . . . . . . . . . . 9
8 Video switch installation and cabling diagram (cars with Apps, TV,
night vision and DVD changer only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9 Installing and connecting the video switch (cars with Apps, TV,
night vision and DVD changer only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
14 Video switch wiring diagram (cars with Apps, TV, night vision and DVD changer only) . . . . . . . . . . . . . . . . . 21
15 DVD changer/TV adapter cable wiring diagram (only when video switch is installed) . . . . . . . . . . . . . . . . . . 22
" #
$
% & ' ( )
* + , - . / 0 1 ;
Legend
A Retrofit cable
B Camera cable
C Control unit (not supplied in the retrofit kit)
D Reversing camera control unit mount
E Tailgate button
F Amplifier mount
G Camera
H Cable tie with holder (5 x)
I Hexagon nut M5 (4 x)
J Hexagon nut M6 (2 x)
K Cable tie (20 x)
L Fuse 5 A
M Miniature connector (2 x)
N Hexagon screw M6 (2 x)
O Sheet metal nut M6
P GN 10+5-pin socket casing
AA
AB AC AD AE AF AG
AM
AH AI AJ AK AL 010 0047 Z
Legend
ISTA No.
Conduct a brief test –––
Disconnect the negative pole of the battery 12 00 ...
A10 A
A9 A1
A8
A7
A6 A3 A2
A5 A4
B2 B1
F01 0095 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
cross-section slot
A Retrofit cable --- --- --- ---
A1 SW 10-pin socket casing --- --- At control unit C A167*2B
A2 SW 6-pin socket casing Cars with video switch only (original or retrofitted)
At video switch AA (disconnect branch A3 and remove cable ---
--- --- from branch A2)
Cars without video switch only A40*1B
Leave branches A2 and A3 plugged in ---
A3 SW 6-pin pin housing Cars with video switch only (original or retrofitted)
Separate branches A2 and A3 (not required) ---
--- ---
Cars without video switch only
Leave branches A2 and A3 plugged in ---
A4 Cable open CAN_H OR/GN Cars with video switch only (original or retrofitted)
0.35 mm2 Not required ---
Cars without video switch only A95*2B
At IHKA control panel A95 with miniature connector M PIN 3
A5 Cable open CAN_L GN Cars with video switch only (original or retrofitted)
0.35 mm2 Not required ---
Cars without video switch only A95*2B
At IHKA control panel A95 with miniature connector M PIN 4
A6 Socket contact FBAS_+ RT Cars with video switch only (original or retrofitted)
0.35 mm2 Not required ---
Cars without video switch only A42*1B
At head unit high PIN 21
A7 Socket contact FBAS- WS Cars with video switch only (original or retrofitted)
0.35 mm2 Not required ---
Cars without video switch only A42*1B
At head unit high PIN 24
A8 Socket contact FBAS_ Shield Cars with video switch only (original or retrofitted)
shield 0.26 mm2 Not required ---
Cars without video switch only A42*1B
At head unit high PIN 23
A9 Socket contact Terminal 15 GN/BL Connect to RR (HR) power distribution box Z2*10B
0.50 mm2 PIN 2
A10 Ring eyelet M6 Terminal 31 BR At ground support point in the luggage compartment on Z10*12B
0.50 mm2 the”left
AB8 A
AB7 AB1
AB6
AB5
AB4
AB3 AB2
F01 0253 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
cross-section slot
AB Retrofit cable --- --- --- ---
AB1 SW 54-pin socket casing --- --- At video switch AA A40*1B
AB2 Cable open CAN_H OR/GN At IHKA control panel A95 with miniature A95*2B
0.35 mm2 connector AJ PIN 3
AB3 Cable open CAN_L GN At IHKA control panel A95 with miniature A95*2B
0.35 mm2 connector AJ PIN 4
AB4 Socket contact FBAS_+ BL At head unit high A42*1B
0.35 mm2 PIN 21
AB5 Socket contact FBAS_- WS At head unit high A42*1B
0.35 mm2 PIN 24
AB6 Socket contact FBAS_ shield Shield At head unit high A42*1B
0.26 mm2 PIN 23
AB7 Socket contact Terminal 30B RT/SW Connect to RR (HR) power distribution box Z2*10B
0.50 mm2 PIN 10
AB8 Ring eyelet M6 Terminal 31 BR At ground support point in the luggage compartment Z10*12B
0.50 mm2 on the left
AC1
AC4 AC2
AC AC3
AE AE1
AE6
AE5 AE2
AE4 AE3 F01 0097 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
cross-section slot
AC DVD changer adapter cable --- --- Cars with DVD changer only ---
AC1 Socket contact FBAS_+ BL With branch AB1 to video switch AA A40*1B
0.35 mm2 PIN 3
AC2 Socket contact FBAS_- WS With branch AB1 to video switch AA A40*1B
0.35 mm2 PIN 21
AC3 Socket contact FBAS_ Shield With branch AB1 to video switch AA A40*1B
Shield 0.26 mm2 PIN 39
AC4 SW 3-pin pin housing --- --- At socket casing AD ---
A Retrofit cable
B Camera cable
C Control unit
G Camera
AA Video switch (retrofitted or already installed)
"&
"#"$ ""
;
AA Video switch
AB Video switch retrofit cable
AC DVD changer adapter cable
AE TV adapter cable
AH
010 0042 Z
AB
AA
AB7
010 0043 Z
AB7
1
011 0026 Z
AI
F121
011 0159 Z
';
AC1-AC3
010 0050 Z
AE1-AE3
010 0051 Z
1
G
E
010 0052 Z
K
H
B1
B 010 0053 Z
1 2
H
F01 0062 Z
F D
010 0054 Z
N 010 0064 Z
010 0055 Z
F01 0167 Z
F01 0139 Z
010 0062 Z
All cars
Screw branch A10, eyelet diameter 6 mm, to ground
support post Z10*12B.
Route branch A9 along the rear panel to RR (HR) power
distribution box.
A10
Z10*12B
A9 F01 0140 Z
A9
1
F01 0147 Z
F123
F01 0141 Z
Z2 A42
A4* A5*
A95*2B
A9* A8*
Z10*12B
A42*1B A7* A6*
A3*
A2*
A1*
A167*2B
C*/A167
A1* B2*
A167*2B A167*7B
B1*
A24*2B
A10*
Z10*12B
G*/A24 F01 0255 Z
Legend
Cable colours
'
; "
;# "#
#@'
"# "# "# "#
"#
"# "#
#@'
"#
"#
"""
"#
;#
"# F01 0256 Z
Legend
Cable colours
A25
AD* A25*1B
AC1*
AE4* AE5* AE6*
AC3*
AE3*
AC1* AC2*
AE1* AE2*
AB1* AB1*
AA* AA*
F01 0142 Z
Legend
Cable colours