Professional Documents
Culture Documents
7SS5 Binary Input Voltage Selection
7SS5 Binary Input Voltage Selection
7SS5 Binary Input Voltage Selection
3.3 Matching the Control Voltage for the Binary Inputs and
Inserting the Buffer Battery
Control voltage
Warning!
Only one jumper may be fitted per binary input.
When delivered, the binary inputs of the EAZ and D-CPU modules in the central unit,
and the EFE or EFE_10 modules in the bay units, are configured for 220 V rated
control voltage.
For each binary input, different switching thresholds can be selected. This is done on
the central unit by means of 3 jumpers on the EAZ module and 4 jumpers on the D-
CPU module, and in the bay units by 3 jumpers each on the EFE or EFE_10 modules.
Central unit
Warning!
Dangerous voltages may be present inside the device!
Make sure to switch the auxiliary voltage off before opening the front panel.
To change the rated control voltages of the binary inputs in the central unit:
Open the front panel. The location of the EAZ and D-CPU module is shown in
Figure 2-2, page 18.
Remove the front plug connectors X3, X4, X5 on the D-CPU module
(Figure 3-2, page 36).
Press down the locking bolt of the modules at the bottom guide rail.
Use the extraction handle (included in the delivery) to pull out the module.
Change the rated control voltages for the binary inputs of the EAZ module as
desired by relocating the jumpers (shown in Figure 3-1, page 35 and Table 3-1,
page 35).
Change the rated control voltages for the binary inputs of the
D-CPU module by relocating the jumpers (shown in Figure 3-2, page 36 and Table
3-2, page 36).
To insert the buffer battery into the central unit:
Press the battery firmly into its snap-in holder (see Figure 3-2, page 36) on the D-
CPU module. Observe the correct battery polarity!
34 7SS52 V4 Manual
E50410-A0012-U501-A4-7691-4
Matching the Control Voltage for the Binary Inputs and Inserting the Buffer Battery
Figure 3-1 Location of the jumpers on the EAZ module (central unit)
Table 3-1 Control voltage for the binary inputs on the EAZ (central unit) in relation to the
fitted jumper
BI1 to BI5 (on the D-CPU module, Table 3-2, page 36)
7SS52 V4 Manual 35
E50410-A0012-U501-A4-7691-4
Getting Started
Figure 3-2 Location of the jumpers and the buffer battery on the D-CPU module (central unit)
Table 3-2 Control voltage for the binary inputs on the D-CPU module (central unit) in
relation to the fitted jumper
36 7SS52 V4 Manual
E50410-A0012-U501-A4-7691-4
Matching the Control Voltage for the Binary Inputs and Inserting the Buffer Battery
Warning!
Dangerous voltages may be present inside the device!
Make sure to switch the auxiliary voltage off before opening the front panel.
To change the rated control voltages of the binary inputs in a bay unit:
Open the front panel. The location of the EFE module is shown in Figure 2-4, page
21.
Remove the plug connector X1 to the front plate on the EFE module (Figure 3-3,
page 37) and pull out the module.
Change the rated control voltages of the binary inputs to the desired settings, see
Figure 3-3, page 37 and Table 3-3, page 38.
To insert the buffer battery into the bay unit:
Press the battery firmly into its snap-in holder (see Figure 2-4, page 21) on the PFE
module. Observe the correct battery polarity! The polarity is marked on the back
of the board.
EFE
7SS52 V4 Manual 37
E50410-A0012-U501-A4-7691-4
Getting Started
Table 3-3 Control voltage for the binary inputs on the EFE (bay unit) in relation to the fitted
jumper
38 7SS52 V4 Manual
E50410-A0012-U501-A4-7691-4
Matching the Control Voltage for the Binary Inputs and Inserting the Buffer Battery
Warning!
Dangerous voltages may be present inside the device!
Make sure to switch the auxiliary voltage off before opening the front panel.
To change the rated control voltages of the binary inputs in a bay unit:
Open the front panel. The location of the EFE_10 module is shown in Figure 2-5,
page 22.
Remove the plug connector X1 to the front plate on the EFE_10 module (Figure 3-
4, page 39) and pull out the module.
Change the rated control voltages of the binary inputs to the desired settings, see
Figure 3-4, page 39 and Table 3-4, page 40.
To insert the buffer battery into the bay unit:
Press the battery firmly into its snap-in holder (see Figure 2-5, page 22) on the PFE/
SVW module. Observe the correct battery polarity! The polarity is marked on the
back of the board.
Figure 3-4 Location of the jumpers on the EFE_10 module (bay unit 7SS525)
7SS52 V4 Manual 39
E50410-A0012-U501-A4-7691-4
Getting Started
Table 3-4 Control voltage for the binary inputs on the EFE_10 (bay unit) in relation to the
fitted jumper
40 7SS52 V4 Manual
E50410-A0012-U501-A4-7691-4