Professional Documents
Culture Documents
TMO AnchorScope Process Guide
TMO AnchorScope Process Guide
TMO AnchorScope Process Guide
2. Scope Name – “5A99” in Scope Name/ EAMS Scope (AIR6449 Radios/Antenna to be used for
B41/N41)
- B41 – Single BB6630 for Alpha-Beta-Gamma – AIR649 ( New Site Build) – T Cells
- N41 – Single BB6630 for Alpha-Beta-Gamma – AIR6449 ( New Site Build) – A Cells
- B25 on LTE Legacy – Radios depends on Buckets
- LTE RNDCIQ
- NR RNDCIQ
- WCDMA RNDCIQ
- GSM CDD
- LTE Kget
- LTE ATND
- NR ATND
- Sitelist
Precheck Commands ( General ) :-
st fdd
hget ru prod
hget du prod
st rilink
hget rilink riportref
get . rfbranchref
get . rfportref
get . auportref
get . carrierref
hget . sectorcarrierref
st sec
st cell
st carr
cabx
get . eutranCellCoverage
get . isshared
st field
get . ^cellid$
get Transport=1,Synchronization=1,RadioEquipmentClock=1,NodeGroupSyncMember=1
Prechecks In CIQ:-
1. eNB Info tab RBS type and Cabinet Controlling DUL should be of type Enclosure 6160.
Cabinet Controlling
RBS type DUL
Enclosure
6160 Enclosure 6160
2. In eUtran Parameters Tab Check Band value for L19_2C – Should be 25.
3. If LTE and NR RND is combined then need to check and fill the Cluster and subnetwork in gNB info tab.
- LTE RNDCIQ
- LTE ATND
- Sitelist.(Lxxxxx2)
GMO Step - B41 NSB – GMO – 4G/5G NSB
Inputs N41
- LTE RNDCIQ
- NR RNDCIQ
- 5G ATND
- Kget
- Sitelist.(Nxxxx2)
GMO Step - N41 Full AP – GMO – 4G/5G NSB
- LTE RNDCIQ
- NR RNDCIQ
- 5G ATND
- LTE ATND
- Kget ( In Folder).
- Sitelist. ( LxxxxxA Lxxxxxxx2 Mxxxxxx – One space each in horizontal).
PostChecks:-
MMBB Scripts:-
1. If MMBB Already Integrated – need to keep - 1c2c/inter_DU/PTP scripts.
2. If MMBB Not Integrated and sequence of Integration is MMBB first and then Anchor – Provide complete
package also thorough postcheck on relation scripts are required as below :-
- 1c2c of Anchor Legacy script from GMO contains D-band relation, need to delete D-band relation
manually____ but if MMBB is already Integrated no L700 is present on Legacy.
- InterDU in MMBB scripts (especially legacy) , as L19_2C is not yet added at the time of MMBB , need
to remove L19_2C relation manually.
Legacy Scripts :-
1. For Bucket 1 :-
- Legacy Folder(L_folder) contains the B25_Add scripts, check Radio definitions, Rilinks, Port mapping and
sector/cell creation part. Thorough checks on relation scripts is mandatory.
2. For Bucket 2:-
- Legacy folder contains 4424_Radio_swap scripts and B25_Add scripts all previously mentioned checks are
to be carried out.
3. NGS Scripts has to provided as per site requirement,
- If NGS already defined then need to provide NGS set scripts.
- If NGS not defined need to provide NGS Create scripts.
Postchecks include defining of Radios and Ports as per BBU type and Add scripts. Fingerprint has to be
replaced in NGS_Create scripts.
B41 Scripts :-
NSB scripts has to be added with sequence number as #1 and B41 add scripts as #2. All add script and relation
scripts checks as previously mentioned.
N41 Scripts :-
Complete package to be added – ENDC folder should have eNB and gNB ENDC scripts.
GSM Scripting
GSM ENM/OSS IP :-
CM454
CM454 A IEBS952 CM454 40 40 49 1 0 YES RBB44_1D AIR32 112
Login process:-
GO-AIR Values
Cases:-
Case 1- If we already have Go AIR Values mapped with MCTR, and final SOW also need Go AIR , then
we must need to use same Go AIR Values for final SOW/MCTR
Case-2 - If we already have Go AIR Values mapped with MCTR, and final SOW don’t need Go AIR –
We need to Un-map Go AIR values from MCTRs
Case 3 – If no GO AIR values in prechecks, and final SOW also need Go AIR, then we use Go-AIR
values from the last used from the command ‘RXGCP:GOTY=AIR;’ value by adding 30 or 40 to that
value.
Radio MCT GO
RBB SW Version
Type R AIR
RBB44_1 B1316R087 YE
AIR32 4x4x4
D D S
RBB44_1 B1316R087
RRU32 4x4x4 NO
D D
RBB44_1 RRU441 B1321R1G0
4x4x4 NO
D 5 0
RBB12_1
RUS 1x1x1 B1313R079F NO
A
RBB11_1
RUS 1x1x1 B1313R079F NO
A
Carry out Prechecks as in the below document, change cell_name/TGG/MCTR as per the GSM CDD. Follow the
same hierarchy as in the precheck.
GMO Steps :-
GMO Pop ups has to be filled as per site and final configuration.
Postcheck:-
WCDMA Scripting :-
get . fqband
st aux
get . radiobuild
get . maxTot
GMO Process :-
Inputs:-
KGET( IN folder)
SL
GMO Steps:-
Changes to be done:-
RBS folder
1. oam_Access_DUW & SiteComplete_DUW ----used for Scratch_Load only (but do keep in your package )
3. External HW ::
1. radioBuildingBlock :- RBB
2. cpriLineRate :-RBB11/RBB12 – Ex2 || RBB22/RBB24 – Ox2 || RBB44 --- Ox4
3. auUnitType auUnitType :- radiotype
4. antennaType :- RRU = 55 / RU=0 / AIR == -1
5. if RBB44_1D :-add branch C & D
6. numberOfTxBranches / numberOfRxBranches as per RBB used
7. numHsCodeResources :-takes the value higher among hsCodeResourceId of sectors
RNC folder : add “Utrancell_power_change” script and change scrambling code & power values as per CIQ (dyn
RN tab)
Script Packages:-
Attaching scripts for Bucket 1 and Bucket 2, WCDMA and GSM scripts are included in package.