Home
‘Antennas
QFH
Calculator
Language:
Espanol
Deutsch
Themes:
‘Simple helicoidal
Qi
Introduction
Calculator
Simulations
Dimensions
Groundplane
Images
Rendering
Version 4
Version 2
MHz
2m
ON7EQ 70cm
Balthazar
Nev G3LMO_
DNA Antenna
Vaisala GPS
Input the data
Design frequency
Input data
Number of turns
Length of one turn
(in wavelengths)
1150, MHz os x4 T=]
Bending radius Conductor diameter Width/height ratio
fis mm — mm faces
Calculate
of
Results ? |
Wavelength Compensated wavelength Bending correction
f2000 mm
20 mm
Larger loop
fa mm
Hnrizantal canaratar
Total length Vertical separator
2175.1 mm 1807.9 mm
Total compensated Compensated vertical
length separation
[2200.8 mm 777.9 mm
Antenna height Internal diameter
H1=6645 mm Dit=72504 mm.
Compensated horiz.
704.4
686. 3amD1= 924mm
;, Smaller loop
: Total length
eT mm
Compensated total
length
827 mm
Antenna height
H2=f632 mm
Horizontal separator
2276 mm
Generate a di
lling template
separation
Det= 2624 mm
Vertical tube
[682mm
Compensated vertical tube
[7382 mm
Internal diameter
Di2=;276 mm
Compensated horiz,
separator
De2=f248 mm
To generate a drilling template in PDF form, please enter the following extra data:
Vertical support tube diameter: mmHorizontal support tube diameter: mm __Generate
Legend |
This calculator generates a lot of data! Take care in the use of the information in order not
to make mistakes.
Here's a little explanation:
Design frequency
Evident?
Number of turns
What's the twist of the antenna? (normally 0.5 or 1 turns)
Length of one turn
A few variations of the antenna exist. Normally the circumference (length of the loop)
is 1 wavelength, but 1.5 wavelength and 2 wavelength versions exist (and work).
Bending diameter
As it's impossible to bend the corner abruptly at 90 degrees, this value is needed for
the calculations. It's measure from the bending center to the center of the tube.
Conductor diameter
External diameter of the tube or coax cable.
Diameter/height ratio
Most frequently this ratio is 0.44, but slightly lower values (0.3 to 0.4) give better
horizon coverage.
Compensated wavelength
‘Wavelength, compensated according to the conductor diameter.
Bending correction
Correction value needed according to the bending diameter.
Compensated total length
Total length of the loop, compensated for the bending effect, and the fact that the loop
must be slightly larger (or smaller)
Compensated vertical conductor
Length of the vertical conductor (without the 'bends').
Compensated horizontal separation
This is in fact the horizontal part without the 'bends', and corresponds to the horizontal
pipe necessary to support the cable
Antenna heiaht{eight of the loop (twisted!).
Internal diameter
The diameter of the (imaginary) cylinder on which the loop would be wound.
(c) John Coppens ON6JC/LWSHAZHome
‘Antennas
QEH
Calculator
Language:
Espanol
Deutsch
Themes:
‘Simple helicoidal
QFH
Introduction
Calculator
Simulations
Dimensions
Groundplane
Images
Rendering
Version 1
Version 2
van 137MH2
ON7EQ 2m
ON7EQ 70cm
Balthazar
Nev G3LMO_
DNA Antenna
Vaisala GPS
YodMHg OEY
Input the data
Input data
Length of one turn
Design frequency Number of turns {in wavelengths)
1400 MHz 0.5 | 1 |
Bending radius Conductor diameter Width/height ratio
{5mm (eee ae
Calculate
Results
Wavelength Compensated wavelength Bending correction
[0mm fa mm
qj Larger loop
Total length Vertical separator
[56 mm [5083 -mm
Total compensated Compensated vertical
length separation
fia mm [ae mm
Antenna height Internal diameter
H1=|254.1 mm Di1={109.6 mm
Harizantal canarator
Compensated horiz.
\2Det 209
ese! Te
ees
a
(ot.08re ee rp
Di=[11e mm
SAGES Smaller loop
ca Total length
Compensated total
ae length
= [500.8 mm
Antenna height
H2=[2478 mm
Horizontal separator
D2=[106.4—— mm
a Sot
— [757 mm
Generate a drilling template
separation
Det= [ers mm
Vertical tube
f294 mm
Compensated vertical tube
f264 mm
Internal diameter
Di2=f1044 mm
Compensated horiz.
separator
De2=[764 mm
To generate a drilling template in POF form, please enter the following extra data:
Vertical support tube diameter: mmHorizontal support tube diameter: mm __ Generate
Legend
This calculator generates a lot of data! Take care in the use of the information in order not
to make mistakes...
Here's a little explanation:
Design frequency
Evident?
Number of turns
‘What's the twist of the antenna? (normally 0.5 or 1 turns)
Length of one turn
‘A few variations of the antenna exist. Normally the circumference (length of the loop)
is 1 wavelength, but 1.5 wavelength and 2 wavelength versions exist (and work).
Bending diameter
As it's impossible to bend the corner abruptly at 90 degrees, this value is needed for
the calculations. It's measure from the bending center to the center of the tube.
Conductor diameter
External diameter of the tube or coax cable.
Diameter/height ratio
Most frequently this ratio is 0.44, but slightly lower values (0.3 to 0.4) give better
horizon coverage.
Compensated wavelength
Wavelength, compensated according to the conductor diameter.
Bending correction
Correction value needed according to the bending diameter.
Compensated total length
Total length of the loop, compensated for the bending effect, and the fact that the loop
must be slightly larger (or smaller).
Compensated vertical conductor
Length of the vertical conductor (without the 'bends’)
Compensated horizontal separation
This is in fact the horizontal part without the ‘bends’, and corresponds to the horizontal
pipe necessary to support the cable
Antenna heiahtInternal diameter
The diameter of the (imaginary) cylinder on which the loop would be wound.
(c) John Coppens ONSJC/LW3HAZ mall