Professional Documents
Culture Documents
Jencons Dispenser Used Guide
Jencons Dispenser Used Guide
Instructions
PERIMATIC GP
OPERATOR MANUAL
BS EN ISO 9002
No FM 15114
No RS 27480
Introduction .........................................................................................................i
Installing the Tubing .......................................................................i
Interfacing with the PERIMATIC GP ....................................... ii
Approvals ..................................................................................... iii
Quickstart for a pre-programmed PERIMATIC GP ..................iii
Dispensing ......................................................................................................11
Manual & automatic dispensing ..................................................11
Dispensing in conjunction with the PERIMATIC ROBOTIC
MODULE .............................................................................. 12
Manual dispensing using the foot switch .....................................12
Specification ......................................................................................................16
JENCONS PERIMATIC GP
INTRODUCTION OPERATOR
Instructions
Installing the Tubing PERIMATIC silicone tubing is fitted by loosening the red
knob and lifting off the tubing clamp, both of which are
illustrated in figure 1. The tubing is then laid into the arc of
the rotor casting, facilitated by turning the rotor by hand as
required, before clamping the tubing into place and
tightening the red knob.
NOTE. Ensure that the clamp does not pinch or constrict the
tubing through over-tightening of the red knob. The unit will
not operate unless the door panel is down.
Door panel
Rotor
Red Knob
Tubing Clamp
JENCONS i PERIMATIC GP
OPERATOR
Instructions
Interfacing with the The PERIMATIC GP has two sockets on the rear panel:-
PERIMATIC GP • Mains socket
• Foot switch/ ROBOTIC MODULE socket
On/Off switch
Mains socket
JENCONS ii PERIMATIC GP
OPERATOR
Instructions
LCD Display
Cursor keys
Conventions used in Throughout the manual the following conventions are used
the manual to describe the keyboard keys:
• The soft keys are referred to as ‘buttons’, e.g. from the
main menu press the ‘MEMORY’ button.
• The keypad keys and the START/STOP keys are shown
enclosed thus <START>.
Initial Setup This section illustrates how the user would set up various
parameters, such as language used, speed etc, upon receipt
of a new machine. It also shows that this procedure need
only be carried out once as all parameters remain stored,
even when the unit is switched off.
JENCONS 1 PERIMATIC GP
INITIAL SETUP OPERATOR
Instructions
Accessing the Setup The Setup Menu is accessed by holding down any one of the
Menu soft keys whilst the power is switched on at the rear of the
machine. When the key is released the display will show the
following message:
Setup Program
Enter Password
Selecting a Language Press the key beneath the ‘COUNTRY’ option on the
display. The display will show the following message:
Still using the soft keys, press ‘NEXT’ until the desired
language is displayed and press ‘ACCEPT’ to confirm this
selection. The program will then return to the Setup Menu.
Exit Program Mode To exit the Setup Menu press the ‘ACCEPT’ button in the
main Setup Menu above. The PERIMATIC GP will reset
and the display will show the Main Menu.
JENCONS 2 PERIMATIC GP
SETTING THE OPERATING OPERATOR
Instructions
PARAMETERS
Introduction Before dispensing is performed the PERIMATIC GP needs
to know certain things, these are :-
1 How much liquid to dispense.
2 Whether the dispenser is running in Automatic or
Manual Mode.
3 How many times to repeat dispensing (Automatic Mode
only).
4 The delay from the finish of one dispense to the start of
the next dispense (Automatic Mode only).
5 The pumping profile and timings.
6 The tubing diameter in use.
7 Whether better accuracy is required by pumping an exact
number of rotor half turns.
8 The direction of rotation.
JENCONS 3 PERIMATIC GP
OPERATOR
Instructions
Setting the repeat From the Setup Options Menu press ‘COUNT’; the display
dispense count will show:
No of Doses 10
ACCEPT QUIT DELETE
Enter the time delay using the cursor keys (the decimal point
is inserted automatically).
JENCONS 4 PERIMATIC GP
OPERATOR
Instructions
Automatic & Manual In Automatic Mode the dispenser will perform a dispense
Modes (set using ‘VOLUME’ command) and then wait for a
predefined time (set using the ‘DELAY’ command). This
sequence may then be repeated a number of times (set using
‘COUNT’).
In Manual Mode the PERIMATIC GP will dispense one
dose and return to its previous menu.
JENCONS 5 PERIMATIC GP
OPERATOR
Instructions
Setting the The pumping rate initially takes two forms; slow pumping
pumping rate and fast pumping. In addition to this the PERIMATIC GP
also performs the following combinations :
The word on the left of the top line denotes the start speed,
the middle word the run speed and the right word the finish
speed.
Press the ‘NEXT’ button until the required combination of
start, run & finish speeds are displayed.
You will notice that when a combination of slow and fast
speeds are selected an additional ‘TIME’ button appears.
This allows the time spent at the selected start or finish
speed to be set.
EXAMPLE. Using the SLOW-FAST-SLOW speed option.
Press ‘TIME’; the display will show:
Start/ Finish Time
START QUIT FINISH
JENCONS 6 PERIMATIC GP
OPERATOR
Instructions
JENCONS 7 PERIMATIC GP
OPERATOR
Instructions
Setting the rotor The rotor on the PERIMATIC GP can run either clockwise
direction or anti-clockwise.
Press ‘DIRECTION’; the display will show:
Run Clockwise
NEXT ACCEPT
JENCONS 8 PERIMATIC GP
OPERATOR
Instructions
JENCONS 9 PERIMATIC GP
OPERATOR
Instructions
JENCONS 10 PERIMATIC GP
DISPENSING OPERATOR
Instructions
JENCONS 11 PERIMATIC GP
OPERATOR
Instructions
Dispensing using the Plug the foot switch into the 3 pin socket on the rear of the
foot switch PERIMATIC GP. Press the foot switch once to start the
pumping operation and again to stop. Using the foot switch
in this way is identical to using the ‘PUMP’ soft key or
<START> button in Manual or Automatic Mode.
JENCONS 12 PERIMATIC GP
STORING /RECALLING /REVIEWING OPERATOR
Instructions
PROGRAMS
When power is removed from the PERIMATIC GP the
current setup is remembered. In addition to this the
PERIMATIC GP can store and recall up to 10 previous
settings, each of which may have a 20 character description
attached to it to describe its various parameters.
All operating information for the PERIMATIC GP is stored
in a memory location, including the language in use as well
as pump speed and tubing flow constants.
From the Main Menu press ‘MEMORY’ to enter the
Memory Menu:
Recall/ Store/ Review
RECALL STORE REVIEW
The display will show the current description stored for that
location. Use keys <4> and <6> to move cursor left and right
and the <2> and <8> keys to increase or decrease the
character under the cursor. Pressing <5> will copy the
character to the left of the cursor to the current cursor
position.
Press ‘ACCEPT’ to store the description and return to the
main menu.
JENCONS 13 PERIMATIC GP
OPERATOR
Instructions
JENCONS 14 PERIMATIC GP
ERROR MESSAGES OPERATOR
Instructions
*******ERROR*******
A dispensing volume of 0ml was entered
Cannot Pump 0ml (invalid). Try again with a volume between
0.5ml and 9999.9ml.
*******ERROR******* The PERIMATIC GP can only dispense up
MAX VOL is 9999.9ml to 9999.9ml. Re-enter a lower figure.
*******ERROR*******
The PERIMATIC GP can only repeat a dis-
Max doses are 999 pense count of up to 999. Re-enter a lower
figure.
Operating Error Description
SPEED profile has been selected but not the
Speed profile set to SLOW /FAST/
START and FINISH times.
SLOW but PERIMATIC GP pumps
all of dose on fast
JENCONS 15 PERIMATIC GP
SPECIFICATION OPERATOR
Instructions
Pumping rate
3mm bore - 2.1ml/s (slow) 4.4ml/s (fast)
5mm bore - 4.6ml/s (slow) 11.8ml/s (fast)
8mm bore - 11.9ml/s (slow) 22.4ml/s (fast)
Program Storage - 10
JENCONS 16 PERIMATIC GP
OPERATOR
Instructions
PERIMATIC GP
(SCIENTIFIC) LTD