Professional Documents
Culture Documents
Script Exer3
Script Exer3
Script Exer3
1. Create > Arc > Circ pt+rad > Radius 2.6 > Origin > Backup...
2. Create > Arc > Circ pt+rad > Radius 1.5 > Origin > Backup...
3. Create > Arc > Circ pt+rad > Radius 1 > Origin > Backup...
(Screen Fit)
4. Create > Arc > Circ pt+rad > Radius 0.36 > Coordinate 0.8,2 > Backup...
5. Create > Line > Tangent > Angle > Select the smallest circle > Angle 90 > Length 1.5 > Select the
6. Create > Line > Horizontal > Origin > Length 2 > Y coordinate 1.973 > Backup...
7. Create > Arc > Tangent > 2 entities > Radius 0.42 > Select the smallest circle and the horizontal line
8. Create > Arc > Tangent > 2 entities > Radius 0.23 > Select the previously created circle and the
11. Modify > Trim > 1 entity > Select the line, then click the circle right below it
Click the upper part of the circle right next to the line, then click the cicle on its left
Select the buttom part of the middle circle, then click the trimmed circle on the right
Select again the buttom part of the middle circle and click the circle on its left
Select the upper part of the smallest circle, then click the largest cicle > Backup...
12. Create > Line > Horizontal > Origin > Length -3 > Y coordinate -0.6 > Backup...
13. Create > Line > Polar > Origin > Degrees 130 > Length 3 > Backup...
14. Create > Line > Parallel > Side/dist > Select the diagonal line > Click anywhere at quadrant 3 >
16. Modify > Trim > 1 entity > Click the quadrant 2 side of the largest circle, then click the trimmed
Click again the quadrant 2 side of the largest circle, then click the horizontal line
Click the middle part of the horizontal line, then click the trimmed circle on the left (Screen zoom
on quadrant 3)
Click the left part of the horizontal line, then click the created fillet next to it
Click the lower part of the diagonal line, then click the fillet > Backup… (Screen fit)
18. Create > Line > Polar > Origin > Degrees -80 > Length 3 > Backup...
19. Create > Line > Parallel > Side/dist > Select the previously created diagonal line > Click anywhere
20. Create > Line > Vertical > Origin > 0,-3 > X coordinate -0.856 > Backup...
21. Create > Line > Vertical > Origin > 0,-3 > X coordinate 1.1 > Backup...
22. Create > Line > Horizontal > Endpoint (endpoint of the vertical line on the left) Endpoint (endpoint of
23. Create > Line > Parallel > Side/dist > Select the horizontal line > Click anywhere below > Distance
24. Create > Arc > Tangent > 3 ents/pts > Select the upper horizontal line, vertical line on the left, and
25. Create > Arc > Tangent > 3 ents/pts > Select the upper horizontal line, vertical line on the right, and
26. Create > Fillet > Radius 0.5 > Select the diagonal line on the left and the lower horizontal line >
Backup...
27. Delete the vertical lines and the diagonal line between them> Backup...
28. Modify > Trim > 1 entity > Click the middle part of the upper horizontal line, then click the arc below,
on the right
Click again the middle part of the same horizontal line, then click the arc on top of it
Click the other horizontal line below, then click the arc on the right
Click again the same horizontal line, then click the fillet arc on the left ( to extend the line)
Click the diagonal line above the fillet arc, then click the fillet arc
Click the other diagonal line on the left, then click the other diagonal line on its right (to extend
the line)
Click the longer diagonal line below, then click the other diagonal line on the left (to trim)
Click the quadrant 4 side of largest remaining circle, then click the arc below it, in quadrant 3
Click again same circle, then click the tangential line above (to extend) > Backup...