Professional Documents
Culture Documents
P Atca Unpack
P Atca Unpack
DN70653621
Issue 2-0
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This document is not an official
customer document and Nokia Siemens Networks does not take responsibility for any errors
or omissions in this document. This document is intended for the use of Nokia Siemens
Networks customers only for the purposes of the agreement under which the document is
submitted. No part of this documentation may be used, reproduced, modified or transmitted in
any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks
welcomes customer comments as part of the process of continuous development and
improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity
or performance of the mentioned hardware or software products are given “as is” and all
liability arising in connection with such hardware or software products shall be defined
conclusively and finally in a separate agreement between Nokia Siemens Networks and the
customer.
IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS
DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO
SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES
SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS
INTERRUPTION, BUSINESS OPPORTUNITY OR DATA, that might arise from the use of this
document or the information in it.
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED
BY APPLICABLE MANDATORY LAW, NO WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-
INFRINGEMENT, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR
CONTENTS OF THIS DOCUMENT. NOKIA SIEMENS NETWORKS RESERVES THE RIGHT
TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR
NOTICE.
This document and the product it describes are considered protected by copyrights and other
intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark
of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective
owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2011. All rights reserved.
Contents
6 Conversion factors...............................................................................30
Unpacking the ATCA Cabinet and Shelf (EC208-A, ACH16-A and ASH16-A)
Summary of changes
Issue 2-0
Packaging information of the shelf ASH16-A has been added.
The name of this document has been changed from Unpacking the
ATCA Cabinet and Shelf to Unpacking the ATCA Cabinet and Shelf
(EC208-A, ACH16-A and ASH16-A)
Issue 1-5
The safety information in this document has been revised on the basis of
ANSI Z535.6-2006 and ISO 3864-2:2004.
Issue 1-4
A new chapter, Unpacking the shelf, was added because of the new
delivery model.
Photos were updated because of delivery model change.
Placement information of door hinges and screw accessories bag was
added.
NOTICE: The field replaceable units (FRUs) are very sensitive to rough
treatment. Handle the FRUs with care during all installation phases.
Check the contents of your delivery against the packing list. The
document ATCA HW Installation Quick Guide is placed in the accessory
box inside the shelf container.
10. Remove the cardboard frame from around the cabinet by lifting it
up.
12. Remove the accessory bag located inside the corrugated end
support.
The end support is marked with stickers.
Figure 11 Moving the cabinet to the correct lifting position and lifting it up
Unpacking the ATCA Cabinet and Shelf (EC208-A, ACH16-A and ASH16-A)
Four lifting eyes are included in the delivery. They can be found in a
plastic bag attached to the top end of the cabinet. The lifting eyes can be
used for lifting the cabinet to an upright position with lifting equipment or
when moving the cabinet on the installation site.
When using the lifting eyes, lifting belts must be correctly attached
through all four lifting eyes. Particularly when moving a fully equipped
cabinet, make sure that the angle between the belt and the top of the
cabinet is at least 60 degrees.
When lifting the cabinet to an upright position using lifting equipment, lift
the cabinet carefully and place the bottom corners of the cabinet gently
on the floor to raise the cabinet to an upright position.
Figure 14 Lifting the cabinet using the lifting eyes and lifting equipment
The blades, RTMs and AMCs are pre-installed in the shelf. The cable
set, cable tray and the power distribution units are delivered separately
in the shelf container. All transceiver sockets are equipped with
protective dust caps.
Unpacking the ATCA Cabinet and Shelf (EC208-A, ACH16-A and ASH16-A)
1. Remove the packing list attached to the case. Store the packing list
for future reference.
2. Check the shelf position on the cabinet from the shelf sticker
attached to the container (see figure below).
3. Cut the plastic straps attaching the container to the pallet.
8. Remove the dehydrant bags and the bag containing the cable tray
from the protective cushions on top of the shelf
9. Remove the protective cushions and the bubble film covering the
unit
Figure 19 Removing the dehydrant bags, cable tray and the cushion
6 Conversion factors
The following conversion factors should be used when unpacking and
installing the ATCA cabinet and associated equipment:
Metric Imperial
1 kilogram (kg) = 2.2046 lb
1 meter (m) = 3.2808 ft
2.54 centimeters (cm) = 1 in