Professional Documents
Culture Documents
qx3440 GSHDSL Um en
qx3440 GSHDSL Um en
i
3.15 Unit Line Rate.................................................................................. 25
3.16 Unit Upgrade Firmware ................................................................... 25
3.17 Customer Information Setup............................................................ 26
3.18 Unit Load Default Configuration ...................................................... 27
3.19 Unit Reset........................................................................................ 27
3.20 Far End Reset ................................................................................. 28
4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)................... 29
4.1 G.SHDSL (2 ports, 2 pairs) Sub-Menu ............................................ 29
4.2 Unit Configuration............................................................................ 29
4.2.1 Far-end: G.SHDSL-DTE ................................................................................. 29
4.2.2 Far-end: G.SHDSL-T1 .................................................................................... 30
4.2.3 Far-end: G.SHDSL-E1 .................................................................................... 30
4.2.4 Far-end: G.SHDSL-BRIDGE .......................................................................... 31
4.2.5 Far-end: G.SHDSL-ROUTER ......................................................................... 31
4.3 Unit Status ....................................................................................... 32
4.3.1 Far-end: G.SHDSL- DTE ................................................................................ 32
4.3.2 Far-end: G.SHDSL- T1 ................................................................................... 32
4.3.3 Far-end: G.SHDSL- E1 ................................................................................... 33
4.3.4 Far-end: G.SHDSL- BRIDGE ......................................................................... 33
4.3.5 Far-end: G.SHDSL- ROUTER ........................................................................ 34
4.3.6 Line Power (2 ports) ....................................................................................... 34
4.4 Unit Performance Report ................................................................. 35
4.5 Unit Alarm Queue ............................................................................ 36
4.6 Unit Alarm History ........................................................................... 36
4.7 HDSL Information ............................................................................ 38
4.8 Customer Information Display ......................................................... 38
4.9 Unit System Setup ........................................................................... 38
4.9.1 Far-end: G.SHDSL-DTE ................................................................................. 40
4.9.2 Far-end: G.SHDSL-T1 .................................................................................... 40
4.9.3 Far-end: G.SHDSL-E1 .................................................................................... 41
4.9.4 Far-end: G.SHDSL-BRIDGE .......................................................................... 41
4.9.5 Far-end: G.SHDSL-ROUTER ......................................................................... 42
4.9.6 Advance System Setup .................................................................................. 42
4.10 Unit Loopback and Test................................................................... 44
4.10.1 Far-end: G.SHDSL- DTE ................................................................................ 44
4.10.2 Far-end: G.SHDSL- T1 ................................................................................... 45
4.10.3 Far-end: G.SHDSL- E1 ................................................................................... 45
4.10.4 Far-end: G.SHDSL- BRIDGE ......................................................................... 46
4.10.5 Far-end: G.SHDSL- ROUTER ........................................................................ 46
4.11 Remote-Bert .................................................................................... 47
4.12 Unit Alarm Setup ............................................................................. 48
4.13 Unit Clear Alarm Queue & History ................................................... 49
4.14 Unit Clear Performance Data .......................................................... 50
4.15 Unit Line Rate.................................................................................. 50
4.16 Unit Upgrade Firmware ................................................................... 51
4.17 Customer Information Setup............................................................ 51
4.18 Unit Load Default Configuration ...................................................... 52
4.19 Unit Reset........................................................................................ 53
4.20 Far End Reset ................................................................................. 53
ii
LIST OF FIGURES
LIST OF TABLES
iii
CHAPTER 1 Product Introduction
1 Product Introduction
1.1 Description
CXR’s G.shdsl plug-in card is designed for QX3440 series. This card allows direct connection to wire pairs
using 16PAM transmission technology. Versatility of this card comes from the choice of data rates, with the
lower data rates applicable to longer reaches. The G.shdsl plug-in card can work with SH331x, and is
compatible with other CXR G.shdsl equipment.
The G.shdsl plug-in card supports configuration and diagnostics using a local or remote terminal connected
to the main unit. This allows in-service diagnostics and fault isolation.
1.2 Specification
G.shdsl Line Interface
Number of port: 4 or 2 Clock
Line code: 16-TCPAM, full duplex with adaptive echo cancellation Source: From System, Line
Data rate for 4-channel G.shdsl: n x 64Kbps (n= 3 to 31) Diagnostics Test
Data rate for 2-channel G.shdsl: n x 64Kbps (n= 3 to 15) G.shdsl Loopback: To-LINE, To-bus
Electrical: Unconditioned 19-26 AWG twisted pair BERT: QRSS
Connector: RJ45
Sealing current: Max. 20 MA source current
CXR-QX3440
G.shdsl
1
CHAPTER 1 Product Introduction
4 Wires
E1/T1 to DTE/Router
2 Wires
E1/T1 to E1/T1
E1/DTE: 200-2056 Kbps
T1: 200-1544 Kbps
E1/T1 CXR-QX3440 CXR
E1/T1
G.SHDSL G.SHDSL
Master Modem
E1/T1 to DTE/Router
Note: QX3440 G.SHDSL card is able to manage a remote device through remote control.
2
CHAPTER 2 Installation
2 Installation
2.1 Site Selection
The following list indicates a site selection guideline. Users need to follow this guideline to select a proper
installation site.
Location of the Rack should be part of the central office equipment layout design. Considerations
should be given to entrance cable routing and -48 Vdc power.
The installation site should have -48 Vdc power. An optional AC/DC power converter can be used.
Use Only with Class 2 power source, -48 Vdc, 100 watts.
The G.SHDSL card is designed to be plugged into any of the available slots from 1 to 12 in the
CXR-QX3440 devices. There are two tyeps of G.SHDSL cards: 2 ports and 4 ports. The front panel is
shown in the following figure.
3
CHAPTER 2 Installation
4 Ports:
Alarm Type
Alarm Type Alarm Description
Number
LOS,MASTER-LOOP1 Master Loop-1 Loss of Signal 20
LOS,MASTER-LOOP2 Master Loop-2 Loss of Signal 21
LOS,SLAVE-LOOP1 Slave Loop-1 Loss of Signal 22
LOS,SLAVE-LOOP2 Slave Loop-2 Loss of Signal 23
LOS/LOF,MASTER-E1 Master E1 Loss of Signal/ Loss of Frame 24
LOS/LOF,SLAVE-E1 Slave E1 Loss of Signal/ Loss of Frame 25
ES15M,MASTER-LOOP1 Master Loop-1 Error Second in current 15-minute interval 26
ES15M,MASTER-LOOP2 Master Loop-2 Error Second in current 15-minute interval 27
ES15M,SLAVE-LOOP1 Slave Loop-1 Error Second in current 15-minute interval 28
ES15M,SLAVE-LOOP2 Slave Loop-2 Error Second in current 15-minute interval 29
ES15M,MASTER-E1 Master E1 Error Second in current 15-minute interval 30
ES15M,SLAVE-E1 Slave E1 Error Second in current 15-minute interval 31
Master Loop-1 severely Error Second in current 15-minute
SES15M,MASTER-LOOP1 32
interval
Master Loop-2 severely Error Second in current 15-minute
SES15M,MASTER-LOOP2 33
interval
Slave Loop-1 severely Error Second in current 15-minute
SES15M,SLAVE-LOOP1 34
interval
Slave Loop-2 severely Error Second in current 15-minute
SES15M,SLAVE-LOOP2 35
interval
Master E1 severely Error Second in current 15-minute
SES15M,MASTER-E1 36
interval
SES15M,SLAVE-E1 Slave E1 severely Error Second in current 15-minute interval 37
ES24H,MASTER-LOOP1 Master Loop-1 Error Second in current 24-hour 38
ES24H,MASTER-LOOP2 Master Loop-2 Error Second in current 24-hour 39
ES24H,SLAVE-LOOP1 Slave Loop-1 Error Second in current 24-hour 40
ES24H,SLAVE-LOOP2 Slave Loop-2 Error Second in current 24-hour 41
1
CHAPTER 2 Installation
2
CHAPTER 2 Installation
If the “Current Firmware Bank” is “1”, pull the G.SHDSL interface out from the main chassis. Then adjust
jumper 7 to be "ON", please see also below diagram. Plug the G.SHDSL interface into the main chassis.
Then reboot the system. The current firmware bank will be switched from Bank 1 to Bank 2.
NOTE: As long as the jumper 7 is set as "ON", the current firmware bank will be switched to the other
after each system rebooting. The user is advised to adjust the jumper 7 to be "OFF" after finish
downloading the current firmware bank.
2.6 LED
Table 2-3 Front-Panel LED Table (2-channel and 4-channel G.SHDSL)
LED Color
Indication
GH1 GH2 GH3 GH4
Green SYNC
Flashing Green Test
Red UNSYNC or Power on
3
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Under the Controller Menu, press “U” to choose a slot for G.SHDSL port. The screen will show as below.
Then press “P” to choose G.SHDSL port, press ENTER to get into the Port Menu.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u = = = 2 1 :4 8: 2 9 0 4 /1 6 /2 0 09
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
To display port system, enter ”C”. The screens of system setup of far-end for G.SHDSL-DTE, G.SHDSL-T1,
G.SHDSL-E1(Master), and G.SHDSL-E1(Slave) are shown as follows.
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : L I NE
D AT A RA T E : 7 68 K b ps
D TE C LO C K : N OR M A L
D TE D AT A : N OR M A L
D TE R TS : A CT I V E
D TE T TM : O FF
D TE V .5 4 : O FF
D S 1 T i me Sl o ts : D TE I NT E RF A CE : V . 35
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 ]
4
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : I N TE R NAL
D S1 F RA M E : E SF
D S1 C OD E : B 8Z S
D S1 C AS : O FF
D S1 T im e S l ot s :
[ i 1 1 11 1 11 1 11 1 1 ii i iii i i ii i ]
x DS L ca r ri e s D S1 t im e sl o t s a s:
D S 1 T i me Sl o ts : T S 0 2 0 3 0 4 0 5 0 6 07 0 8 0 9 1 0 1 1
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] TS 12 13
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : L I NE
D S1 F RA M E : C RC - O FF
D S1 C OD E : H DB 3
D S1 T im e S l ot s :
[ i 1 1 11 1 11 1 11 1 1 ii i iii i i ii i ii i ii i ii ]
x DS L ca r ri e s D S1 t im e sl o t s a s:
T S 0 1 0 2 0 3 0 4 0 5 06 0 7 0 8 0 9 1 0
D S 1 T i me Sl o ts : TS 11 12
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ]
5
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : L I NE
D AT A RA T E : 7 68 K b ps
D TE C LO C K : N on e
D TE D AT A : N on e
D TE R TS : N on e
D TE T TM : N on e
D TE V .5 4 : N on e
D S 1 T i me Sl o ts : D TE I NT E RF A CE : B R ID G E
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 ]
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : L I NE
D AT A RA T E : 7 68 K b ps
D TE C LO C K : N on e
D TE D AT A : N on e
D TE R TS : N on e
D TE T TM : N on e
D TE V .5 4 : N on e
D S 1 T i me Sl o ts : D TE I NT E RF A CE : R O UT E R
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 ]
6
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
To view the port status screen, enter ”I”. The screens of port status of far-end for G.SHDSL-DTE,
G.SHDSL-T1, G.SHDSL-E1 (Master), and G.SHDSL-E1(Slave) are shown as follows. All of the following
cards support remote link identification: DTU-6, DTU-10, HDSL, G. SHDSL-2, G. SHDSL-4, E1, QE1, and
MiniQE1.
3.3.1 Far-end: G.SHDSL- DTE
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us] [R e m ot e L i nk Id e n ti f ica t i on ]
D a u gh t er Ca r d : No Dau g h te r C a rd TYPE : CPE
[ C A S S ta t us ]
C A S : D I SA B LE
7
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
[ D a ug h te r C a rd S ta t us] [R em o t e L in k I d en t i fi c ati o n ]
D a u gh t er Ca r d : No Dau g h te r C a rd T YP E : C PE
[ C A S S ta t us ]
C A S : D I SA B LE
[ D a ug h te r C a rd S ta t us] [ Re m o te Li n k I de n t if i cat i o n]
D a u gh t er Ca r d : No Dau g h te r C a rd TY P E : CP E
[ C A S S ta t us ]
C A S : D I SA B LE
8
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us] [R e m ot e L i nk Id e n ti f ica t i on ]
D a u gh t er Ca r d : No Dau g h te r C a rd TYPE : CPE
[ C A S S ta t us ]
C A S : D I SA B LE
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us] [R e m ot e L i nk Id e n ti f ica t i on ]
D a u gh t er Ca r d : No Dau g h te r C a rd TYPE : CPE
[ C A S S ta t us ]
C A S : D I SA B LE
9
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Under Port Menu the screen will show “ Daughter Card: Line Power Single” when it include line power.
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us] [ Re m o te Li n k I de n t if i cat i o n]
D a u gh t er Ca r d : Li n e P o w er Si n gl e TYP E : C PE
[ C A S S ta t us ]
C A S : D I SA B LE
To view the performance report screen, enter ”R”. Move the cursor to select the desired location,
MASTER-LOOP1 or SLAVE-LOOP1, then press ENTER to confirm the selection. The current selection will
be highlighted by an asterisk (*).
Far-end: G.SHDSL- T1
Far-end: G.SHDSL- E1
10
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Press ENTER from the above screen, the detail performance report will show as below.
SLOT 2 G.SHDSL-2 PORT 3 = = = U n it Pe r fo r m an c e R e p or t = = = 11 : 3 5:3 3 12 / 21 / 20 0 8
L o c at i on : M A ST E R -L O OP1
V a l id Se c on d s i n C u rre n t 1 5 -M i n I nt e r va l : 6 3 4 s ec o nd s
V a l id 15 - Mi n I n t er v als i n C ur r en t 2 4 - ho u r: 5
[ 1 5 M i nu t e r eg i s te r s]
[ - - -- - - E S -- - - -- ] [- - -- - - SE S -- - -- ] [- - - --- U AS -- - -- ]
C u r re n t: 0 0 0
1-4 : 0 0 0 0 0 0 0 0 0 0 0 0
5-8 : 0 . . . 0 . . . 30 8 . . .
9-12 : . . . . . . . . . . . .
1 3 -1 6 : . . . . . . . . . . . .
1 7 -2 0 : . . . . . . . . . . . .
2 1 -2 4 : . . . . . . . . . . . .
2 5 -2 8 : . . . . . . . . . . . .
2 9 -3 2 : . . . . . . . . . . . .
[ 2 4 h o ur re g is t e rs ]
[ C u rr e nt ] [ 1 ] [ 2 ] [ 3 ] [ 4 ] [ 5 ] [ 6 ] [ 7 ]
ES : 0 . . . . . . .
SES: 0 . . . . . . .
UAS: 30 8 . . . . . . .
11
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
To view the alarm history report, enter “H” from the Port Menu. The following screen will show up.
[ - - -- A la r m T yp e - -- - ][C n t ][ S ta ] [- S et u p -]
L O S ,M A ST E R- L OO P 1 1 MAJ
L O S ,S L AV E -L O OP 1 1 MAJ
E S 1 5M , MA S TE R -L O O P1 0 MAJ 1
E S 1 5M , SL A VE - LO O P 1 0 MAJ 1
S E S 15 M ,M A ST E R- L O OP 1 0 MAJ 1
S E S 15 M ,S L AV E -L O O P1 0 MAJ 1
E S 2 4H , MA S TE R -L O O P1 0 MAJ 1
E S 2 4H , SL A VE - LO O P 1 0 MAJ 1
S E S 24 H ,M A ST E R- L O OP 1 0 MAJ 1
S E S 24 H ,S L AV E -L O O P1 0 MAJ 1
L O W N O IS E M A RG I N 0 MAJ 1
Far-end: G.SHDSL- T1
SLOT 2 G.SHDSL-2 PORT 3 == = U n it Al a r m H is t o ry == = 1 0: 1 7: 1 1 1 2 /2 2 / 2 0 08
[ - - -- A la r m T yp e - -- - ][C n t ][ S ta ] [- S et u p -]
L O S ,M A ST E R- L OO P 1 1 MAJ
L O S ,S L AV E -L O OP 1 1 MAJ
L O S /L O F, S LA V E- T 1 1 ALM MAJ
E S 1 5M , MA S TE R -L O O P1 0 MAJ 1
E S 1 5M , SL A VE - LO O P 1 0 MAJ 1
E S 1 5M , SL A VE - T1 0 MAJ 1
S E S 15 M ,M A ST E R- L O OP 1 0 MAJ 1
S E S 15 M ,S L AV E -L O O P1 0 MAJ 1
S E S 15 M ,S L AV E -T 1 0 MAJ 1
E S 2 4H , MA S TE R -L O O P1 0 MAJ 1
E S 2 4H , SL A VE - LO O P 1 0 MAJ 1
E S 2 4H , SL A VE - T1 0 MAJ 1
S E S 24 H ,M A ST E R- L O OP 1 0 MAJ 1
S E S 24 H ,S L AV E -L O O P1 0 MAJ 1
S E S 24 H ,S L AV E -T 1 0 MAJ 1
L O W N O IS E M A RG I N 0 MAJ 1
12
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Far-end: G.SHDSL- E1
SLOT 2 G.SHDSL-2 PORT 3 = = = U n it Al a r m H is to r y = = = 1 0 : 19 : 12 1 2/ 2 2/ 2 00 8
[ - - -- A la r m T yp e - -- - ][C n t ][ S ta ] [- S et u p -]
L O S ,M A ST E R- L OO P 1 1 MAJ
L O S ,S L AV E -L O OP 1 1 MAJ
L O S /L O F, S LA V E- E 1 1 ALM MAJ
E S 1 5M , MA S TE R -L O O P1 2 ALM MAJ 1
E S 1 5M , SL A VE - LO O P 1 0 MAJ 1
E S 1 5M , SL A VE - E1 0 MAJ 1
S E S 15 M ,M A ST E R- L O OP 1 0 MAJ 1
S E S 15 M ,S L AV E -L O O P1 0 MAJ 1
S E S 15 M ,S L AV E -E 1 0 MAJ 1
E S 2 4H , MA S TE R -L O O P1 0 MAJ 1
E S 2 4H , SL A VE - LO O P 1 0 MAJ 1
E S 2 4H , SL A VE - E1 0 MAJ 1
S E S 24 H ,M A ST E R- L O OP 1 0 MAJ 1
S E S 24 H ,S L AV E -L O O P1 0 MAJ 1
S E S 24 H ,S L AV E -E 1 0 MAJ 1
L O W N O IS E M A RG I N 0 MAJ 1
[ - - -- - -- - -- - -- M AS T ER - - -- - -- - -- - -]
[ Lo o p -1 ]
N o i se Ma r gi n : 21. 0 dB
M a x . N MR : 2 2. 0 dB 11 : 43 : 31 1 0/ 2 1/0 7
M i n . N MR : 2 0. 5 dB 11 : 43 : 38 1 0/ 2 1/0 7
[ - - -- - -- - -- - -- S LA V E - - - -- - -- - -- - -]
[ Lo o p -1 ]
N o i se Ma r gi n : 21. 0 dB
M a x . N MR : 2 2. 5 dB 11 : 43 : 33 1 0/ 2 1/0 7
M i n . N MR : 2 0. 5 dB 11 : 43 : 38 1 0/ 2 1/0 7
13
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Press “V” from the Port Menu to display the related customer Information for each port.
SLOT 2 G.SHDSL-2 PORT 3 === Customer Information === 14:07:02 01/20/2010
ARROW KEYS: CURSOR MOVE, BACKSPACE to edit, ESC to abort
P1: ________________________________________________________________
P2:
P3:
P4:
14
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
To setup port system, select “S (unit setup)" from the Port Menu.
Then move the cursor to select "General" for general setting. The current selection will be highlighted by an
asterisk (*).
SLOT 2 G.SHDSL-2 PORT 3 == = U n it Se t u p = = = 1 4: 2 6: 55 0 4/ 1 6/ 2 00 9
> > Se l ec t ? *G e n er a l A dv a nc e
The screens of system setup of far-end for G.SHDSL-DTE, G.SHDSL-T1, G.SHDSL-E1(Master), and
G.SHDSL-E1(Slave) are shown as follows.
3.9.1 Far-end: G.SHDSL-DTE
Here "i" (eye, idle) means TS that cannot be used for transmission of any data; "1" (one) means active TS
carrying customer data; "X" means TS available for customer data, but not in active use.
NOTE: For time slot setting, user must to do TSI map setting from "System Setup (MAP)" of "Controller
Setup" menu. And start the setting from the first time slot. Please note that "1" must be set in the front of "X".
That is user cannot put in (iXXX111), Also, the 111 must be consecutive. The sum of [l] and [x] should equal
to the sum of line rate.
15
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Here "i" (eye, idle) means TS that cannot be used for transmission of any data; "1" (one) means active TS
carrying customer data; "X" means TS available for customer data, but not in active use.
NOTE: For time slot setting, user must to do TSI map setting from "System Setup (MAP)" of "Controller
Setup" menu. And start the setting from the first time slot. Please note that "1" must be set in the front of "X".
That is user cannot put in (iXXX111), Also, the 111 must be consecutive. The sum of [l] and [x] should equal
to the sum of line rate.
SLOT 2 G.SHDSL-2 PORT 3 = == Un i t S et u p == = 1 0 :2 0 :2 1 1 2 /2 2 /2 0 08
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
L i n e R at e : 7 76 K b ps (1 p ai r )
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : I N TE R NAL
D S1 F RA M E : E SF
D S1 C OD E : B 8Z S
D S1 C AS : O FF
S el e c t 1 2 C ha n ne l s f r om D S 1 t im e s l ot s
t o r o ut e i n to xD S L c h ann e l s:
D S 1 T i me Sl o ts : D S1 T im e S l ot s :
[ 1 11 1 11 1 11 1 XX i i iii i i ii i ii i ii i ii i i ] [ 11 1 11 1 11 1 11 X X ii i iii i i ii i ]
x DS L ca r ri e s D S1 t im e sl o t s a s:
T S 0 1 0 2 0 3 0 4 0 5 06 0 7 0 8 0 9 1 0
TS 11 12
Here "i" (eye, idle) means TS that cannot be used for transmission of any data; "1" (one) means active TS
carrying customer data; "X" means TS available for customer data, but not in active use.
NOTE: For time slot setting, user must to do TSI map setting from "System Setup (MAP)" of "Controller
Setup" menu. And start the setting from the first time slot. Please note that "1" must be set in the front of "X".
That is user cannot put in (iXXX111), Also, the 111 must be consecutive. The sum of [l] and [x] should equal
to the sum of line rate.
SLOT 2 G.SHDSL-2 PORT 3 = = = U ni t S e tu p === 11 : 48 : 03 1 2 / 21 / 20 0 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
L i n e R at e : 7 76 K b ps (1 p ai r )
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
M A X D A TA RA T E : 76 8 Kbp s C LO C K S O UR C E : L I NE
D S1 F RA M E : C RC - O FF
D S1 C OD E : H DB 3
S el e c t 1 2 C ha n ne l s f r om D S 1 t im e s l ot s
t o r o ut e i n to xD S L c h ann e l s:
D S1 T im e S l ot s :
D S 1 T i me Sl o ts : [ i1 1 11 1 11 1 11 X X ii i iii i i ii i ii i ii i ii ]
[ 1 11 1 11 1 11 1 XX i i iii i i ii i ii i ii i ii i i ] xDS L ca r ri e s D S1 t im e sl o t s a s:
T S 0 1 0 2 0 3 0 4 0 5 06 0 7 0 8 0 9 1 0
TS 11 12
16
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
17
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
To setup port system, enter ”S” from the Port Menu. Then move the cursor to select "Advance" for advance
setting. The current selection will be highlighted by an asterisk (*).
U n i t- 1 4 G SH D SL - 4 P 1 == = U n it Se t u p = = = 1 4: 2 6: 55 0 4/ 1 6/ 2 00 9
> > Se l ec t ? G e n er a l * A dv a nc e
Press ENTER from the above menu. If the far-end site supports advance setup, the screen will show as the
first menu. If not, the screen will show as the second menu. Press ESC key to continue. Then the system will
ask for confirmation about the new setting. Press "Y" to confirm the new configuration or "N" to abort. To
enable the new configuration, press "V" from the "Controller Menu" to save the current setting.
SLOT 2 G.SHDSL-2 PORT 3 == = U n it Se t u p = = = 1 4: 2 7: 41 0 4/ 1 6/ 2 00 9
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
L i n e R at e : 1 92 8 K bp s (1 p ai r )
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
A N N EX TY P E : A A NN E X T Y PE : A
C L O CK MO D E : P L E SIO C H RO N OU S C L O CK M O DE : P LE S IO C H RON O U S
P S D M A SK : S Y M MET R I C P SD M AS K : S YM M E TRI C
P B O M O DE : A U T OMA T I C P BO M OD E : A UT O M ATI C
18
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
To enter the loopback test screen, enter ”L” from the Port Menu. You will see to options: General and
Remote Bert. Note that the Remote Bert function is only available when the G.shdsl is connected to a
SH331x.
SLOT 2 G.SHDSL-2 PORT 3 === Unit Loopback and Test === 02:59:56 05/24/2009
Select “General”. The screens of the loopback test of far-end for G.SHDSL-DTE, G.SHDSL-T1,
G.SHDSL-E1(Master), and G.SHDSL-E1(Slave) are shown as follows.
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF D TE - TO - LI N E xD S L -TO - L IN E D TE - TO - D TE xD S L -T O -D T E
BERT : * OF F Q RS S
19
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF T 1- T O- L IN E x DS L - TO- L I NE T 1 -T O -T 1 x D SL- T O -T 1
BERT : * OF F Q RS S
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L T O- L I NE
S l a ve Lo o pb a ck : * O FF E 1- T O- L IN E x DS L - TO- L I NE E 1 -T O -E 1 x D SL- T O -E 1
BERT : * OF F Q RS S
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF x DS L -T O -L I NE x D S L-T O - BR G
BERT : * OF F Q RS S
20
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF R TR - TO - LI N E xD S L -TO - L IN E
BERT : * OF F Q RS S
3.11 Remote-Bert
Select “Remote-Bert” from the loopback and test menu. Note that the Remote Bert function is only
available when the G.shdsl is connected to a SH331x. And the G.shdsl Firmware Version should be
V1.07.0 or up.
P a t te r n T yp e : 2 ^1 5 -1
T e s t C ha n ne l s: F ul l
T e s t E na b le : D is a ble
21
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Enable the test status, the Bert status will show on the screen as below:
SLOT 2 G.SHDSL-2 PORT 3 == = R e mo t e B er t === 11 : 47 : 51 0 8 / 15 / 20 0 6
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
P a t te r n T yp e : 2 ^1 5 -1
T e s t C ha n ne l s: F ul l
T e s t E na b le : E na b le
[ B E RT ST A TU S ]
B E R T T YP E : 2^ 15 - 1
B E R T S TA T US : U NSY N C
B I T E R RO R C O UN T : 0
E R R OR S EC O ND S : 0
E L A PS E D S EC O ND S : 1
U N S YN C S EC O ND S : 1
To do alarm setup, enter “M” from the Port Menu. Use arrow keys to move the cursor and TAB key to roll up
options.
Far-end: G.SHDSL- DTE, Bridge, Router
SLOT 2 G.SHDSL-2 PORT 3 = == Un i t A la r m S e tup = == 1 1 :4 8 :3 1 1 2 /2 1 / 2 0 08
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
[ - - -- - T y pe -- - - -- ] [A l a rm ] [ T hr e sh o l d]
L O S ,M A ST E R- L OO P 1 MA J O R
L O S ,S L AV E -L O OP 1 MA J O R
E S 1 5M , MA S TE R -L O O P1 MA J O R 001
E S 1 5M , SL A VE - LO O P 1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 1 MA J O R 001
S E S 15 M ,S L AV E -L O O P1 MA J O R 001
E S 2 4H , MA S TE R -L O O P1 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 1 MA J O R 0 0 00 1
S E S 24 H ,M A ST E R- L O OP 1 MA J O R 0 0 00 1
S E S 24 H ,S L AV E -L O O P1 MA J O R 0 0 00 1
L O W N O IS E M A RG I N MA J O R 01
22
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Far-end: G.SHDSL- T1
SLOT 2 G.SHDSL-2 PORT 3 == = U n it Al a rm S etu p == = 1 0: 2 2: 34 1 2/ 2 2/ 2 00 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
[ - - -- - T y pe -- - - -- ] [A l a rm ] [ T hr e sh o l d]
L O S ,M A ST E R- L OO P 1 MA J O R
L O S ,S L AV E -L O OP 1 MA J O R
L O S /L O F, S LA V E- T 1 MA J O R
E S 1 5M , MA S TE R -L O O P1 MA J O R 001
E S 1 5M , SL A VE - LO O P 1 MA J O R 001
E S 1 5M , SL A VE - T1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 1 MA J O R 001
S E S 15 M ,S L AV E -L O O P1 MA J O R 001
S E S 15 M ,S L AV E -T 1 MA J O R 001
E S 2 4H , MA S TE R -L O O P1 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 1 MA J O R 0 0 00 1
E S 2 4H , SL A VE - T1 MA J O R 0 0 00 1
S E S 24 H ,M A ST E R- L O OP 1 MA J O R 0 0 00 1
S E S 24 H ,S L AV E -L O O P1 MA J O R 0 0 00 1
S E S 24 H ,S L AV E -T 1 MA J O R 0 0 00 1
L O W N O IS E M A RG I N MA J O R 01
Far-end: G.SHDSL- E1
SLOT 2 G.SHDSL-2 PORT 3 == = U n it Al a rm S etu p == = 1 0: 2 3: 08 1 2/ 2 2/ 2 00 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
[ - - -- - T y pe -- - - -- ] [A l a rm ] [ T hr e sh o l d]
L O S ,M A ST E R- L OO P 1 MA J O R
L O S ,S L AV E -L O OP 1 MA J O R
L O S /L O F, S LA V E- E 1 MA J O R
E S 1 5M , MA S TE R -L O O P1 MA J O R 001
E S 1 5M , SL A VE - LO O P 1 MA J O R 001
E S 1 5M , SL A VE - E1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 1 MA J O R 001
S E S 15 M ,S L AV E -L O O P1 MA J O R 001
S E S 15 M ,S L AV E -E 1 MA J O R 001
E S 2 4H , MA S TE R -L O O P1 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 1 MA J O R 0 0 00 1
E S 2 4H , SL A VE - E1 MA J O R 0 0 00 1
S E S 24 H ,M A ST E R- L O OP 1 MA J O R 0 0 00 1
S E S 24 H ,S L AV E -L O O P1 MA J O R 0 0 00 1
S E S 24 H ,S L AV E -E 1 MA J O R 0 0 00 1
L O W N O IS E M A RG I N MA J O R 01
23
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Press “X” from the Port Menu to clear alarm queue and alarm history. Then press “Y” or “N” to confirm the
setting.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u === 1 1 :4 8 :5 9 1 2 /2 1 /2 0 08
C a r d S ta t e : Du r i ng I n it i al i za t io n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
> > Cl e ar al a rm q ue u e o f UN I T 5 - a r e y o u s u r e ? [ Y /N ]
Press “K” from the Port Menu to clear performance data. Then press “Y” or “N” to confirm the setting.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u === 1 1 :4 8 :5 9 1 2 /2 1 /2 0 08
C a r d S ta t e : D ur i ng In i t ial i z at i on
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
= = > C l ea r p e rf o r ma n ce d a ta - a re yo u su r e [ Y / N] ?
24
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
To view the line rate screen, enter ”B” from the Port Menu.
SLOT 2 G.SHDSL-2 PORT 3 = = = L in e R a t e = = = 11 : 50 :3 0 12 / 21 / 20 0 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
Nx64 : 12
L I N E R AT E : 77 6 K bp s
L O O P N UM : Lo o p _O n e
To upgrade firmware, enter ”D” from the Port Menu. Then, select for local or remote firmware download.
SLOT 2 G.SHDSL-4 PORT 1 === Firmware Download === 14:53:50 07/01/2010
B a n k 1 F i rm w ar e Ve r . : S 1. 0 0 1 3/ 1 0/ 2 0 08 (G o od )
B a n k 2 F i rm w ar e Ve r . : S 1. 0 0 1 6/ 1 0/ 2 0 08 (G o od )
W o r ki n g F ir m wa r e B a nk: 2
T F T P S er v er IP : 0 00 . 00 0 .0 0 0. 0 0 0
F i r mw a re Fi l e N a me :
Note: G.shdsl card only supports SH331x for remote download firmware.
After you fill in all the required configuration, press ENTER to start the download procedure.
SLOT 2 G.SHDSL-2 PORT 3 === Upgrade Remote Firmware === 14:54:53 07/01/2010
ARROW KEYS: CURSOR MOVE, Please Input: nnn.nnn.nnn.nnn, BACKSPACE to edit
25
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Press “T” from the Port Menu. Key in the information of the customer that relates to each port.
SLOT 2 G.SHDSL-2 PORT 3 === Customer Information === 14:07:02 01/20/2010
ARROW KEYS: CURSOR MOVE, BACKSPACE to edit, ESC to abort
P1: ________________________________________________________________
P2:
P3:
P4:
26
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Press “Y” from the Port Menu to return to default setting. Then press “Y” or “N” to confirm the setting.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u === 1 1 :5 1 :4 7 1 2 /2 1 /2 0 08
C a r d S t at e : D ur i n g I n i ti a li z at i on
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
Press “Z” from the Port Menu to reset the system. Then press “Y” or “N” to confirm the setting.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u === 1 1 :5 1 :4 7 1 2 /2 1 /2 0 08
C a r d S t at e : D ur i ng I nit i a li z at i on
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
R e s et - a re yo u su r e ? [ Y/ N ]
27
CHAPTER 3 Terminal Operation: G.SHDSL (4 ports, 1 Pair)
Press “W” from the Port Menu to reset the system of remote side. Then press “Y” to confirm the reset or “N”
to abandon.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u = = = 2 1 :4 8: 2 9 0 4 /1 6 /2 0 09
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
R e s et Fa r E n d - ar e yo u su r e ? [ Y /N ]
28
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Under the Controller Menu, press “U” to choose a unit for G.SHDSL port. The screen will show as below.
Then press “P” to choose G.SHDSL port, press ENTER to get into the Port Menu.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u = = = 2 1 :4 8: 2 9 0 4 /1 6 /2 0 09
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
To display port system, enter ”C”. The screens of system setup of far-end for G.SHDSL-DTE, G.SHDSL-T1,
G.SHDSL-E1(Master), and G.SHDSL-E1(Slave) are shown as follows.
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
CAS : OFF C LO C K S O UR C E : L I NE
M A X D A TA RA T E : 15 3 6Kb p s D AT A RA T E : 1 47 2 K bps
D TE C LO C K : N OR M A L
D TE D AT A : N OR M A L
D TE R TS : A CT I V E
D TE T TM : O FF
D TE V .5 4 : O FF
D S 1 T i me Sl o ts : D TE I NT E RF A CE : V . 35
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 1 11 1 i11 1 1 11 1 ]
29
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
CAS : OFF C LO C K S O UR C E : L I NE
M A X D A TA RA T E : 15 3 6Kb p s D S1 F RA M E : D4
D S1 C OD E : B 8Z S
D S1 C AS : ON
D S1 T im e S l ot s :
[ 1 1 1 11 1 11 1 11 1 1 11 1 111 1 1 11 1 ]
x DS L ca r ri e s D S1 t im e sl o t s a s:
D S 1 T i me Sl o ts : T S 0 1 0 2 0 3 0 4 05 06 0 7 0 8 0 9 1 0
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] T S 1 1 1 2 1 3 1 4 15 16 1 7 1 8 1 9 2 0
TS 21 22 23 24
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
CAS : OFF C LO C K S O UR C E : L I NE
M A X D A TA RA T E : 15 3 6Kb p s D S1 F RA M E : C RC - O N
D S1 C OD E : H DB 3
D S1 T im e S l ot s :
[ i 1 1 11 1 11 1 11 1 1 11 1 111 1 1 11 1 1i i ii i ii ]
x DS L ca r ri e s D S1 t im e sl o t s a s:
T S 0 1 0 2 0 3 0 4 0 5 0 6 07 0 8 0 9 1 0
D S 1 T i me Sl o ts : TS 1 1 1 2 1 3 1 4 1 5 1 6 17 1 8 1 9 2 0
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] TS 2 1 2 2 2 3 2 4
30
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
CAS : OFF C LO C K S O UR C E : L I NE
M A X D A TA RA T E : 15 3 6Kb p s D AT A RA T E : 1 53 6 K bps
D TE C LO C K : N on e
D TE D AT A : N on e
D TE R TS : N on e
D TE T TM : N on e
D TE V .5 4 : N on e
D S 1 T i me Sl o ts : D TE I NT E RF A CE : B R ID G E
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 1 11 1 111 1 1 11 1 ]
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
CAS : OFF C LO C K S O UR C E : L I NE
M A X D A TA RA T E : 15 3 6Kb p s D AT A RA T E : 1 53 6 K bps
D TE C LO C K : N on e
D TE D AT A : N on e
D TE R TS : N on e
D TE T TM : N on e
D TE V .5 4 : N on e
D S 1 T i me Sl o ts : D TE I NT E RF A CE : R O UT E R
[ i ii i ii i ii i ii i i iii i i ii i ii i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 1 11 1 111 1 1 11 1 ]
31
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
To view the port status screen, enter ”I”. The screens of port status of far-end for G.SHDSL-DTE,
G.SHDSL-T1, G.SHDSL-E1(Master), and G.SHDSL-E1(Slave) are shown as follows.
[ L O OP - 1] [ L OO P - 2] [ LO O P -1 ] [ LO O P- 2 ] [D T E]
SYNC : YES S Y NC : YE S S YN C : Y ES S YN C : Y ES DS R : YE S
ES : 0 ES : 0 ES : 0 ES : 0 CT S : NO
SES : 0 SES : 0 S ES : 0 S ES : 0 DC D : YE S
UAS : 148 U A S : 16 9 U AS : 1 48 U AS : 1 69 DT R : NO
RTS : NO
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us]
D a u gh t er Ca r d : No Dau g h te r C a rd
[ C A S S ta t us ]
C A S : D I SA B LE
[ L O OP - 1] [ L OO P - 2] [ LO O P -1 ] [ LO O P- 2 ] [T 1 ]
SYNC : YES S Y NC : YE S S YN C : Y ES S YN C : Y ES SY N C : NO
ES : 0 ES : 0 ES : 0 ES : 0 ES : 9
SES : 0 SES : 0 S ES : 0 S ES : 0 SE S : 7
UAS : 264 U A S : 28 5 U AS : 2 64 U AS : 2 85 UA S : 69
T x A IS : NO
T x Y EL : YES
R x A IS : NO
[ L o op b ac k S t at u s ] Rx Y EL : NO
x D S L L oo p ba c k : O F F LO S : YES
S L A VE Lo o pb a ck : O F F LO F : YES
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us]
D a u gh t er Ca r d : No Dau g h te r C a rd
[ C A S S ta t us ]
C A S : D I SA B LE
32
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
[ L O OP - 1] [ L OO P - 2] [ LO O P -1 ] [ LO O P- 2 ] [E 1 ]
SYNC : YES S Y NC : YE S S YN C : Y ES S YN C : Y ES SY N C : NO
ES : 0 ES : 0 ES : 0 ES : 0 ES : 2
SES : 0 SES : 0 S ES : 0 S ES : 0 SE S : 1
UAS : 1 UAS : 1 U AS : 1 U AS : 1 UA S : 2
T x A IS : NO
T x R AI : YES
R x A IS : NO
[ L o op b ac k S t at u s ] Rx R AI : NO
x D S L L oo p ba c k : O F F LO S : YES
S L A VE Lo o pb a ck : O F F LO F : YES
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us]
D a u gh t er Ca r d : No Dau g h te r C a rd
[ C A S S ta t us ]
C A S : D I SA B LE
[ L O OP - 1] [ L OO P - 2] [ LO O P -1 ] [ LO O P- 2 ] [D T E]
SYNC : YES S Y NC : YE S S YN C : Y ES S YN C : Y ES DS R : NA
ES : 0 ES : 0 ES : 0 ES : 0 CT S : NA
SES : 0 SES : 0 S ES : 0 S ES : 0 DC D : NA
UAS : 0 UAS : 0 U AS : 0 U AS : 0 DT R : NA
RTS : NA
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us]
D a u gh t er Ca r d : No Dau g h te r C a rd
[ C A S S ta t us ]
C A S : D I SA B LE
33
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
[ L O OP - 1] [ L OO P - 2] [ LO O P -1 ] [ LO O P- 2 ] [D T E]
SYNC : YES S Y NC : YE S S YN C : Y ES S YN C : Y ES DS R : NA
ES : 0 ES : 0 ES : 0 ES : 0 CT S : NA
SES : 0 SES : 0 S ES : 0 S ES : 0 DC D : NA
UAS : 0 UAS : 0 U AS : 0 U AS : 0 DT R : NA
RTS : NA
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us]
D a u gh t er Ca r d : No Dau g h te r C a rd
[ C A S S ta t us ]
C A S : D I SA B LE
Under Port Menu the screen will show “Daughter Card: Line Power Single” when it include line power.
SLOT 2 G.SHDSL-2 PORT 3 = == Un i t S ta t u s = == 1 0: 3 6: 4 1 12 / 2 6/ 2 00 5
L i n e R at e : 1 03 2 K bp s (2 p ai r s)
[ - - -- - -- - -- - -- M AS T ER - - -- - -- - -- - -] [-- - - -- - -- - -- - S L A VE --- - - -- - -- - -- ]
S er i a l N um b er : 0 0 0 69 4
[ L O OP - 1] [ L OO P - 2] [ LO O P -1 ] [ LO O P- 2 ] [D T E]
SYNC : YES S Y NC : YE S S YN C : Y ES S YN C : Y ES DS R : YE S
ES : 0 ES : 0 ES : 0 ES : 0 CT S : YE S
SES : 0 SES : 0 S ES : 0 S ES : 0 DC D : YE S
UAS : 0 UAS : 0 U AS : 0 U AS : 0 DT R : NO
R T S : YE S
[ L o op b ac k S t at u s ]
x D S L L oo p ba c k : O F F
S L A VE Lo o pb a ck : O F F
BERT : O FF
S L A VE BE R T : OFF
[ D a ug h te r C a rd S ta t us] [ Re m o te Li n k I de n t if i cat i o n]
D a u gh t er Ca r d : Li n e P o w er Du a l T YP E : C PE
[ C A S S ta t us ]
C A S : D I SA B LE
34
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
To view the performance report screen, enter ”R”. Move the cursor to select the desired location,
MASTER-LOOP1 or SLAVE-LOOP1, then press ENTER to confirm the selection. The current selection will
be highlighted by an asterisk (*).
Far-end: G.SHDSL- DTE, Bridge, Router
Far-end: G.SHDSL- T1
Far-end: G.SHDSL- E1
Press ENTER from the above screen, the detail performance report will show as below.
SLOT 2 G.SHDSL-2 PORT 3 = = = U n it Pe r fo r m an c e R e p or t = = = 11 : 5 5:5 8 12 / 22 / 20 0 8
L o c at i on : M A ST E R -L 1
V a l id Se c on d s i n C u rre n t 1 5 -M i n I nt e r va l : 4 4 7 s ec o nd s
V a l id 15 - Mi n I n t er v als i n C ur r en t 2 4 - ho u r: 0
[ 1 5 M i nu t e r eg i s te r s]
[ - - -- - - E S -- - - -- ] [- - -- - - SE S -- - -- ] [- - - --- U AS -- - -- ]
C u r re n t: 0 0 14 8
1-4 : . . . . . . . . . . . .
5-8 : . . . . . . . . . . . .
9-12 : . . . . . . . . . . . .
1 3 -1 6 : . . . . . . . . . . . .
1 7 -2 0 : . . . . . . . . . . . .
2 1 -2 4 : . . . . . . . . . . . .
2 5 -2 8 : . . . . . . . . . . . .
2 9 -3 2 : . . . . . . . . . . . .
[ 2 4 h o ur re g is t e rs ]
[ C u rr e nt ] [ 1 ] [ 2 ] [ 3 ] [ 4 ] [ 5 ] [ 6 ] [ 7 ]
ES : 0 . . . . . . .
SES: 0 . . . . . . .
UAS: 14 8 . . . . . . .
35
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
To view the alarm history report, enter “H” from the Port Menu. The following screen will show up.
Far-end: G.SHDSL- DTE, Bridge, Router
SLOT 2 G.SHDSL-2 PORT 3 = == Un i t A la r m H i sto r y = = = 1 4: 3 9 :44 1 2/ 2 2/ 2 00 8
36
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Far-end: G.SHDSL- T1
SLOT 2 G.SHDSL-2 PORT 3 = = = U n it Al a rm H is t ory = == 1 4: 2 8 :4 6 1 2 / 22 / 20 0 8
Far-end: G.SHDSL- E1
SLOT 2 G.SHDSL-2 PORT 3 = = = U ni t A l ar m Hi s tor y == = 1 5 :1 9 : 17 1 2 /2 2 /2 0 08
37
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Press “N” from the Port Menu to display HDSL Information as below screen shows.
SLOT 2 G.SHDSL-2 PORT 3 = == HD S L I nf o r ma t ion = == 1 4 :4 0 :2 3 1 2 /2 2 / 2 0 08
L i n e R at e : 7 76 K b ps (2 p ai r s)
[ - - -- - -- - -- - -- M AS T ER - - -- - -- - -- - -]
[ Lo o p -1 ] [ Lo o p- 2 ]
N o i se Ma r gi n : 23. 0 dB 2 3. 0 d B
M a x . N MR : 2 3. 0 dB 14 : 18 : 22 1 2/ 2 2/0 4 2 3. 0 d B 1 4: 1 8 :3 0 1 2 /2 2 /0 4
M i n . N MR : 1 9. 5 dB 14 : 16 : 59 1 2/ 2 2/0 4 2 0. 0 d B 1 4: 1 6 :4 2 1 2 /2 2 /0 4
[ - - -- - -- - -- - -- S LA V E - - - -- - -- - -- - -]
[ Lo o p -1 ] [ Lo o p- 2 ]
N o i se Ma r gi n : 22. 0 dB 2 2. 5 d B
M a x . N MR : 2 2. 5 dB 14 : 18 : 26 1 2/ 2 2/0 4 2 3. 0 d B 1 4: 1 8 :3 0 1 2 /2 2 /0 4
M i n . N MR : 1 9. 0 dB 14 : 16 : 59 1 2/ 2 2/0 4 2 0. 0 d B 1 4: 1 6 :5 9 1 2 /2 2 /0 4
Press “V” from the Port Menu to display the related customer Information for each port.
SLOT 2 G.SHDSL-2 PORT 3 === Customer Information === 14:07:02 01/20/2010
ARROW KEYS: CURSOR MOVE, BACKSPACE to edit, ESC to abort
P1: ________________________________________________________________
P2:
P3:
P4:
38
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
> > Se l ec t ? *G e n er a l A dv a nc e R e mo t e RT R
The screens of system setup of far-end for G.SHDSL-DTE, G.SHDSL-T1, G.SHDSL-E1(Master), and
G.SHDSL-E1(Slave) are shown as follows.
(If CAS change please reactive TSI map)
39
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Here "i" (eye, idle) means TS that cannot be used for transmission of any data; "1" (one) means active TS
carrying customer data; "X" means TS available for customer data, but not in active use.
NOTE: For time slot setting, user must to do TSI map setting from "System Setup (MAP)" of "Controller
Setup" menu. And start the setting from the first time slot. Please note that "1" must be set in the front of "X".
That is user cannot put in (iXXX111), Also, the 111 must be consecutive. The sum of [l] and [x] should equal
to the sum of line rate.
SLOT 2 G.SHDSL-2 PORT 3 = = = U ni t S e tu p === 14 : 41 : 24 1 2 / 22 / 20 0 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
L i n e R at e : 7 76 K b ps (2 p ai r s)
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
x D S L M OD E : M A S TER x DS L MO D E : S LA V E
CAS : OFF C LO C K S O UR C E : L I NE
M A X D A TA RA T E : 15 3 6Kb p s D AT A RA T E : 1 53 6 K bps
D TE C LO C K : N OR M A L
D TE D AT A : N OR M A L
D TE R TS : A CT I V E
D TE T TM : O FF
D TE V .5 4 : O FF
D S 1 T i me Sl o ts : D TE I NT E RF A CE : V . 35
[ 1 11 1 11 1 11 1 11 1 1 111 1 1 11 1 11 i ii i ii i i ] MAP P E R M AP P IN G :
[ 1 1 1 11 1 11 1 11 1 1 11 1 111 1 1 11 1 ]
S el e c t 2 4 C ha n ne l s f r om D S 1 t im e s l ot s
t o r o ut e i n to xD S L c h ann e l s:
D S 1 T i me Sl o ts : D S1 T im e S l ot s :
[ 1 11 1 11 1 11 1 11 1 1 111 1 1 11 1 XX i ii i ii i i i] [1 1 11 1 11 1 11 1 11 1 1 111 1 1 11 1 XX ]
x DS L ca r ri e s D S1 t im e sl o t s a s:
T S 0 1 0 2 0 3 0 4 0 5 06 0 7 0 8 0 9 1 0
T S 1 1 1 2 1 3 1 4 1 5 16 1 7 1 8 1 9 2 0
TS 21 22 23 24
40
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
S el e c t 2 4 C ha n ne l s f r om D S 1 t im e s l ot s
t o r o ut e i n to xD S L c h ann e l s:
D S1 T im e S l ot s :
D S 1 T i me Sl o ts : [ i1 1 11 1 11 1 11 1 1 11 1 111 1 1 11 X X i i ii i ii ]
[ 1 11 1 11 1 11 1 11 1 1 111 1 1 11 1 XX i ii i ii i i ] xDS L ca r ri e s D S1 t im e sl o t s a s:
T S 0 1 0 2 0 3 0 4 0 5 06 0 7 0 8 0 9 1 0
T S 1 1 1 2 1 3 1 4 1 5 16 1 7 1 8 1 9 2 0
TS 21 22 23 24
41
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
To setup port system, enter ”S” from the Port Menu. Then move the cursor to select "Advance" for advance
setting. The current selection will be highlighted by an asterisk (*).
SLOT 2 G.SHDSL-2 PORT 3 = == Un i t S et u p == = 1 4 :2 6 :5 5 0 4 /1 6 /2 0 09
> > Se l ec t ? G e n er a l * A dv a nc e R e mo t e RT R
Press ENTER from the above menu. If the far-end site supports advance setup, the screen will show as the
first menu. If not, the screen will show as the second menu. Press ESC key to continue. Then the system will
ask for confirmation about the new setting. Press "Y" to confirm the new configuration or "N" to abort. To
enable the new configuration, press "V" from the "Controller Menu" to save the current setting.
SLOT 2 G.SHDSL-2 PORT 3 = == Un i t S et up = == 1 4 :2 7: 4 1 0 4 /1 6 /2 0 09
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
L i n e R at e : 1 92 8 K bp s (1 p ai r )
[ - - -- - -- - L O CA L -- - --- - - ] [ -- - - -- - F A R- E ND - -- - --- ]
A N N EX TY P E : A A NN E X T Y PE : A
C L O CK MO D E : P L E SIO C H RO N OU S C L O CK M O DE : P LE S IO C H RON O U S
P S D M A SK : S Y M MET R I C P SD M AS K : S YM M E TRI C
P B O M O DE : A U T OMA T I C P BO M OD E : A UT O M ATI C
42
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
43
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
To enter the loopback test screen, enter ”L” from the Port Menu. You will see to options: General and
Remote Bert. Note that the Remote Bert function is only available when the G.shdsl is connected to a
SH331x.
SLOT 2 G.SHDSL-2 PORT 3 === Unit Loopback and Test === 02:59:56 05/24/2009
Select “General”. The screens of the loopback test of far-end for G.SHDSL-DTE, G.SHDSL-T1,
G.SHDSL-E1(Master), and G.SHDSL-E1(Slave) are shown as follows.
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF D TE - TO - LI N E xD S L -TO - L IN E D TE - TO - D TE xD S L -T O -D T E
BERT : * OF F Q RS S
44
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF T 1- T O- L IN E x DS L - TO- L I NE T 1 -T O -T 1 x D SL- T O -T 1
BERT : * OF F Q RS S
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF E 1- T O- L IN E x DS L - TO- L I NE E 1 -T O -E 1 x D SL- T O -E 1
BERT : * OF F Q RS S
45
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF x DS L -T O -L I NE x D S L-T O - BR G
BERT : * OF F Q RS S
[ T E ST ME N U]
x D S L L oo p ba c k : * O FF T O- L OC A L TO - LI N E
S l a ve Lo o pb a ck : * O FF R TR - TO - LI N E xD S L -TO - L IN E
BERT : * OF F Q RS S
46
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
4.11 Remote-Bert
Select “Remote-Bert” from the loopback and test menu. Note that the Remote Bert function is only
available when the G.shdsl is connected to a sH331x. And the G.shdsl Firmware Version should be
V1.07.0 or up.
P a t te r n T yp e : 2 ^1 5 -1
T e s t C ha n ne l s: F ul l
T e s t E na b le : D is a ble
Enable the test status, the Bert status will show on the screen as below:
SLOT 2 G.SHDSL-2 PORT 3 == = R e mo t e B er t === 11 : 47 : 51 0 8 / 15 / 20 0 6
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
P a t te r n T yp e : 2 ^1 5 -1
T e s t C ha n ne l s: F ul l
T e s t E na b le : E na b le
[ B E RT ST A TU S ]
B E R T T YP E : 2^ 15 - 1
B E R T S TA T US : U NSY N C
B I T E R RO R C O UN T : 0
E R R OR S EC O ND S : 0
E L A PS E D S EC O ND S : 1
U N S YN C S EC O ND S : 1
47
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
To do alarm setup, enter “M” from the Port Menu. Use arrow keys to move the cursor and TAB key to roll up
options.
Far-end: G.SHDSL- DTE, Bridge, Router
SLOT 2 G.SHDSL-2 PORT 3 == = U n it Al a rm S etu p == = 1 4: 4 2: 05 1 2/ 2 2/ 2 00 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
[ - - -- - T y pe -- - - -- ] [A l a rm ] [ T hr e sh o l d] [-- - - - T yp e - - -- - - ] [ Ala r m ] [ Th r es h ol d ]
L O S ,M A ST E R- L OO P 1 MA J O R S ES 2 4 H, S LA V E- L OO P 1 M AJO R 0 00 0 1
L O S ,M A ST E R- L OO P 2 MA J O R S ES 2 4 H, S LA V E- L OO P 2 M AJO R 0 00 0 1
L O S ,S L AV E -L O OP 1 MA J O R L OW N OI S E M AR G IN M AJO R 01
L O S ,S L AV E -L O OP 2 MA J O R
E S 1 5M , MA S TE R -L O O P1 MA J O R 001
E S 1 5M , MA S TE R -L O O P2 MA J O R 001
E S 1 5M , SL A VE - LO O P 1 MA J O R 001
E S 1 5M , SL A VE - LO O P 2 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 2 MA J O R 001
S E S 15 M ,S L AV E -L O O P1 MA J O R 001
S E S 15 M ,S L AV E -L O O P2 MA J O R 001
E S 2 4H , MA S TE R -L O O P1 MA J O R 0 0 00 1
E S 2 4H , MA S TE R -L O O P2 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 1 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 2 MA J O R 0 0 00 1
S E S 24 H ,M A ST E R- L O OP 1 MA J O R 0 0 00 1
S E S 24 H ,M A ST E R- L O OP 2 MA J O R 0 0 00 1
Far-end: G.SHDSL- T1
SLOT 2 G.SHDSL-2 PORT 3 = = = U ni t A l ar m Set u p = = = 15 : 23 :4 9 12 / 22 / 20 0 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
[ - - -- - T y pe -- - - -- ] [A l a rm ] [ T hr e sh o l d] [-- - - - T yp e - - -- - - ] [ Ala r m ] [ Th r es h ol d ]
L O S ,M A ST E R- L OO P 1 MA J O R E S2 4 H ,S L AV E -L O OP 2 M AJO R 0 00 0 1
L O S ,M A ST E R- L OO P 2 MA J O R E S2 4 H ,S L AV E -T 1 M AJO R 0 00 0 1
L O S ,S L AV E -L O OP 1 MA J O R S ES 2 4 H, M AS T ER - LO O P 1 M AJO R 0 00 0 1
L O S ,S L AV E -L O OP 2 MA J O R S ES 2 4 H, M AS T ER - LO O P 2 M AJO R 0 00 0 1
L O S /L O F, S LA V E- T 1 MA J O R S ES 2 4 H, S LA V E- L OO P 1 M AJO R 0 00 0 1
E S 1 5M , MA S TE R -L O O P1 MA J O R 001 S ES 2 4 H, S LA V E- L OO P 2 M AJO R 0 00 0 1
E S 1 5M , MA S TE R -L O O P2 MA J O R 001 S ES 2 4 H, S LA V E- T 1 M AJO R 0 00 0 1
E S 1 5M , SL A VE - LO O P 1 MA J O R 001 L OW N OI S E M AR G IN M AJO R 01
E S 1 5M , SL A VE - LO O P 2 MA J O R 001
E S 1 5M , SL A VE - T1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 2 MA J O R 001
S E S 15 M ,S L AV E -L O O P1 MA J O R 001
S E S 15 M ,S L AV E -L O O P2 MA J O R 001
S E S 15 M ,S L AV E -T 1 MA J O R 001
E S 2 4H , MA S TE R -L O O P1 MA J O R 0 0 00 1
E S 2 4H , MA S TE R -L O O P2 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 1 MA J O R 0 0 00 1
48
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Far-end: G.SHDSL- E1
SLOT 2 G.SHDSL-2 PORT 3 = = = U ni t A l ar m Set u p = = = 15 : 17 :2 2 12 / 22 / 20 0 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
[ - - -- - T y pe -- - - -- ] [A l a rm ] [ T hr e sh o l d] [-- - - - T yp e - - -- - - ] [ Ala r m ] [ Th r es h ol d ]
L O S ,M A ST E R- L OO P 1 MA J O R E S2 4 H ,S L AV E -L O OP 2 M AJO R 0 00 0 1
L O S ,M A ST E R- L OO P 2 MA J O R E S2 4 H ,S L AV E -E 1 M AJO R 0 00 0 1
L O S ,S L AV E -L O OP 1 MA J O R S ES 2 4 H, M AS T ER - LO O P 1 M AJO R 0 00 0 1
L O S ,S L AV E -L O OP 2 MA J O R S ES 2 4 H, M AS T ER - LO O P 2 M AJO R 0 00 0 1
L O S /L O F, S LA V E- E 1 MA J O R S ES 2 4 H, S LA V E- L OO P 1 M AJO R 0 00 0 1
E S 1 5M , MA S TE R -L O O P1 MA J O R 001 S ES 2 4 H, S LA V E- L OO P 2 M AJO R 0 00 0 1
E S 1 5M , MA S TE R -L O O P2 MA J O R 001 S ES 2 4 H, S LA V E- E 1 M AJO R 0 00 0 1
E S 1 5M , SL A VE - LO O P 1 MA J O R 001 L OW N OI S E M AR G IN M AJO R 01
E S 1 5M , SL A VE - LO O P 2 MA J O R 001
E S 1 5M , SL A VE - E1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 1 MA J O R 001
S E S 15 M ,M A ST E R- L O OP 2 MA J O R 001
S E S 15 M ,S L AV E -L O O P1 MA J O R 001
S E S 15 M ,S L AV E -L O O P2 MA J O R 001
S E S 15 M ,S L AV E -E 1 MA J O R 001
E S 2 4H , MA S TE R -L O O P1 MA J O R 0 0 00 1
E S 2 4H , MA S TE R -L O O P2 MA J O R 0 0 00 1
E S 2 4H , SL A VE - LO O P 1 MA J O R 0 0 00 1
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
> > Cl e ar al a rm q ue u e o f Un i t 3 - a r e y o u s u r e ? [ Y /N ]
49
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Press “K” from the Port Menu to clear performance data. Then press “Y” or “N” to confirm the setting.
SLOT 2 G.SHDSL-2 PORT 3 = = = P or t M e n u = = = 21 : 48 :2 9 04 / 16 / 20 0 9
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
= = > C l ea r p e rf o r ma n ce d a ta - a re yo u su r e [ Y / N] ?
To view the line rate screen, enter ”B” from the Port Menu.
(After you change the Line Rate or Loop NUM, please reactive the tsi map.)
SLOT 2 G.SHDSL-2 PORT 3 = = = L in e R a te = == 11 : 50 : 30 1 2 / 21 / 20 0 8
A R R OW KE Y S: CU R S OR MOV E , T A B: RO L L O P TI O NS
Nx64 : 12
L I N E R AT E : 77 6 K bp s
L O O P N UM : Lo o p _O n e
50
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
B a n k 1 F i rm w ar e Ve r . : S 1. 0 0 1 3/ 1 0/ 2 0 08 (G o od )
B a n k 2 F i rm w ar e Ve r . : S 1. 0 0 1 6/ 1 0/ 2 0 08 (G o od )
W o r ki n g F ir m wa r e B a nk: 2
T F T P S er v er IP : 0 00 . 00 0 .0 0 0. 0 0 0
F i r mw a re Fi l e N a me :
Press “T” from the Port Menu. Key in the information of the customer that relates to each port.
SLOT 2 G.SHDSL-2 PORT 3 === Customer Information === 14:07:02 01/20/2010
ARROW KEYS: CURSOR MOVE, BACKSPACE to edit, ESC to abort
P1: ________________________________________________________________
P2:
P3:
P4:
51
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Press “Y” from the Port Menu to return to default setting. Then press “Y” or “N” to confirm the setting.
SLOT 2 G.SHDSL-2 PORT 3 = = = P or t M e n u = = = 21 : 48 :2 9 04 / 16 / 20 0 9
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
52
CHAPTER 4 Terminal Operation: G.SHDSL (2 Ports, 2 Pairs)
Press “Z” from the Port Menu to reset the system. Then press “Y” or “N” to confirm the setting.
SLOT 2 G.SHDSL-2 PORT 3 == = P o rt Me nu = == 2 1: 48 : 2 9 0 4/ 1 6/ 2 00 9
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
R e s et - a re yo u su r e? [ Y /N ]
Press “W” from the Port Menu to reset the system of remote side. Then press “Y” to confirm
the reset or “N” to abandon.
SLOT 2 G.SHDSL-2 PORT 3 = == Po r t M en u = = = 2 1 :4 8: 2 9 0 4 /1 6 /2 0 09
C ar d St a te : D u ri n g In i t ia l iz a ti o n
S W ve r si o n: V1 . 0 7. 0 1 0 8 / 10 / 20 0 6
[ D I SP L AY ] [ SE T U P]
C - > U ni t C o nf i g ur a tio n S - > Un i t S ys t em S et u p
I - > U ni t S t at u s L - > Un i t L oo p ba c k a n d T e s t
R - > U ni t P e rf o r ma n ce R e po r t M - > Un i t A la r m S e tu p
Q - > U ni t A l ar m Qu e ue X - > Un i t C le a r A l ar m Qu e u e & H i st o ry
H - > U ni t A l ar m Hi s tor y K - > Un i t C le a r P e rf o rma n c e D at a
N - > H DS L I n fo r m at i on B - > Un i t L in e R a t e
V - > C us t om e r I n fo r mat i o n D is p la y D - > Un i t U pg r ad e Fi r mwa r e
T - > Cu s to m er In f o rm a tio n Se t up
[ L O G] [ MI S C ]
U - > C ho o se Ot h e r S lot Y - > Un i t L oa d D e f au l t C o n fi g
P - > C ho o se G. S H DS L Po r t Z - > Un i t R es e t
F - > L og Of f [ S E TU P ],[ M I SC ] M e nu W - > Fa r E n d R es e t
O - > L og On [ S E TU P ],[ M I SC ] M e nu
E - > R et u rn to C on t rol l e r M ai n M e nu
R e s et Fa r E n d - ar e yo u su r e ? [ Y /N ]
53