Professional Documents
Culture Documents
IECEx PTB 04 0003U
IECEx PTB 04 0003U
0003U Page 1 of 4
IECEx Certificate
of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheres
for rules and details of the IECEx Scheme visit www.iecex.com
Status: Current
Electrical Apparatus: Type 264 Modular PE and Through terminal blocks and terminal strips
Optional accessory:
Marking: Ex e II
Tamb - 55 °C to + 85 °C
Signature:
(for printed version)
Date:
http://iecex.iec.ch/iecex/iecexweb.nsf/ae7eea0d12561594c1256d0200448859/b8d281... 12/01/2010
Certificate of Conformity: IECEx PTB 04.0003U Page 2 of 4
IECEx Certificate
of Conformity
Certificate No.: IECEx PTB 04.0003U
Page 2 of 3
Manufacturing location(s):
This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and
found to comply with the IEC Standard list below and that the manufacturer's quality system, relating to the Ex products
covered by this certificate, was assessed and found to comply with the IECEx Quality system requirements. This
certificate is granted subject to the conditions as set out in IECEx Scheme Rules, IECEx 02 and Operational
Documents as amended.
STANDARDS:
The electrical apparatus and any acceptable variations to it specified in the schedule of this certificate and the identified
documents, was found to comply with the following standards:
IEC 60079-0 : 2000 Electrical apparatus for explosive gas atmospheres - Part 0: General requirements
Edition: 3.1
IEC 60079-7 : 2001 Electrical apparatus for explosive gas atmospheres - Part 7: Increased safety 'e'
Edition: 3
This Certificate does not indicate compliance with electrical safety and performance requirements other than those
expressly included in the Standards listed above.
http://iecex.iec.ch/iecex/iecexweb.nsf/ae7eea0d12561594c1256d0200448859/b8d281... 12/01/2010
Certificate of Conformity: IECEx PTB 04.0003U Page 3 of 4
IECEx Certificate
of Conformity
Certificate No.: IECEx PTB 04.0003U
Page 3 of 3
Schedule
EQUIPMENT:
Equipment and systems covered by this certificate are as follows:
Description of equipment
The screwless modular feed-through and individual terminal types 264-1 .. to 264-2.., with two or four clamping
units, as well as type 264-7.7 screwless protective-conductor terminal block with four clamping units is used to
connect copper conductors in terminal compartments of the type of protection increased safety "e".
The terminals are composed of insulating housing, made from plastic materials PA 66 and clamping units with
cage clamp.
Accessories are: end plates, separator plates and adaptor plates, bridging elements as well as retaining clip
and end brackets.
The terminal is fastened on mounting rails, or on supports with mounting flanges or snap-in mounting feets.
Technical data
Type: 264-1.. to 264-2.. 264-1.. to 264-2.. 264-727/999-950
with jumper plug without jumper plug 264-737/999-950
Max. rated voltage: max. 750 V max. 750 V --
Rated current: 16 A 23 A --
Rated cross section: 1,5 mm² 2,5 mm² 2,5mm²
solid, stranded and flexible
Range of temperature of -55 °C up to +85 °C
use:
Range of ambient -55 °C up to +45 °C
temperature
Key of type designation
Terminal Blocks Description
Type designation
264-120 2-conductor through terminal block for DIN 15 Rail
264-220 4-conductor through terminal block for DIN 15 Rail
264-727/999-950 4-protective-conductor terminal block for DIN 15 Rails
264-125 2-conductor through terminal block for DIN 35 Rail
264-225 4-conductor through terminal block for DIN 35 Rail
264-737/999-950 4-protective-conductor terminal block for DIN 35 Rails
264-131 2-conductor center terminal block
264-231 4-conductor center terminal block
264-130 2-conductor end terminal block with fixing flange
264-230 4-conductor end terminal block with fixing flange
264-132 up to 264-142 2-conductor terminal strips with fixing flanges
264-232 up to 264-242 4-conductor terminal strips with fixing flanges
264-180 2-conductor terminal block with snap-in mounting feet
264-280 4-conductor terminal block with snap-in mounting feet
264-182 up to 264-192 2-conductor terminal strips with snap-in mounting feet
264-282 up to 264-292 4-conductor terminal strips with snap-in mounting feet
Accessories Description
Type designation
210-111 DIN 15 carrier rail, slotted 15x5,5mm/ steel, zinc plated
210-295 DIN 15 carrier rail, unslotted 15x5,5mm/ steel, zinc plated
210-296 DIN 15 carrier rail, slotted 15x5,5mm/ aluminum
210-112 DIN 35 carrier rail, slotted 35x7,5mm/ steel, zinc plated
210-113 DIN 35 carrier rail, unslotted 35x7,5mm/ steel, zinc plated
210-196 DIN 35 carrier rail, slotted 35x7,5mm/ aluminum
264-367 Seperator for Eex e/ Eex i applications
264-368 End- and intermediate plate, grey
264-369 End- and intermediate plate, orange
264-370 End- and intermediate plate, light grey
264-373 End plate, for terminal block with snap-in mounting foot
264-402 Comb type jumper bar, insulated, 2-way
281-482 Comb type jumper bar, 2-way
280-482 Comb type jumper bar, 2-way
281-483 Comb type jumper bar, 3-way
280-483 Comb type jumper bar, 3-way
280-484 Comb type jumper bar, 4-way
280-485 Comb type jumper bar, 5-way
280-490 Comb type jumper bar, 10-way
281-490 Comb type jumper bar, 10-way
281-492 Alternate comb type jumper bar
280-492 Alternate comb type jumper bar
249-101 Screwless end stop, for DIN 15 rail
209-101 Plastic end stop, for DIN 35 rail
249-116 Plastic end stop, for DIN 35 rail
249-117 Plastic end stop, for DIN 35 rail
209-122 Plastic end stop
209-120 Mounting adapter for terminal blocks with snap-in mounting foot
209-137 Mounting adapter for DIN 35 rail
CONDITIONS OF CERTIFICATION: NO
http://iecex.iec.ch/iecex/iecexweb.nsf/ae7eea0d12561594c1256d0200448859/b8d281... 12/01/2010