Professional Documents
Culture Documents
ABB Disconnectors OWD OWIII - EN - 16-04
ABB Disconnectors OWD OWIII - EN - 16-04
www.nepsi.com
Medium Voltage products
Introduction .................................................................................4
Indoor disconnectors type OWD...................................................5
Indoor disconnectors 3-poles type OWIII....................................13
Manual operating mechanisms type NRWO4-3..........................20
Motor operating devices type UEMC 40_...................................22
Electromagnetic interlock type NO5............................................34
www.nepsi.com
only for non-standard
Manual and motor driven operating mechanisms do not form an
distances)
integral part of the disconnector and are supplied to separate
1 – one 01 – 1,2 kV w. 01 – 4000 A (N3) 1 – with lever for orders. The type of operating mechanism applied depends on the
2 – two 03 – 3,6 kV 3150 A (T3) coupling with
type of disconnector, in accordance with table 1 (the table does
3 – three 10 – 12 kV w. 02 – 2500 A (N3) manual operating
20 – 24 kV 2000 A (T3) mechanism not account for pneumatic operating mechanisms).
w. 03 – 2000 A (N3) NRWO4−3 or an
w. 04 – 1600 A isolating rod for 1,2
(N3, T3) kV disconnectors,
Table 1
2 – pneumatic operating
Type of disconnector Type of operating mechanism
mechanism type
NP8 on the right OWD101w.02, OWD301w.02 HE, NRWO4-3, UEMC40 A_
hand side, or isolating rod
3 – pneumatic operating OWD103w.01, OWD103w.02
mechanism type
OWD110w.01, OWD110w.02
NP8 on the left hand
side, OWD120w.02 HE,
4 – two pneumatic OWD303w.01, OWD303w.02 NRWO4-3
operating OWD203w.01, OWD203w.02 UEMC40 A_
mechanisms type
OWD310w.01, OWD310w.02 UEMC40 K6_
NP8,
500 – pole distance 500 mm OWD210w.01, OWD210w.02
OWD320w.02, OWD220w.02
3. Design and operation A mechanism type NP8 is used as pneumatic operating mecha-
One−, two− and three−pole disconnectors type OWD are the ver- nism, with rated pressure 0,6−1,2 MPa, one or two drives are
tical break disconnectors. The base is a steel frame to which the used, depending on the rated pressure and model of the discon-
operating mechanism is fixed. Bracketing insulators are fastened nector in accordance with the table 2.
to the frame and are the mounting for the current circuit which If a disconnector is ordered with pneumatic operating mechanism
consists of two fixed contacts and one moving contact on each or motor UEMC40K6, it is coupled with the mechanism by the
pole. The moving contacts are connected to the shaft by means manufacturer and is an inseparable part of the complete supply.
of insulating pull-rods.
Pressing the moving contact to the fixed contact is solved in such
a way that, at shorting currents, due to the effect of magnetic
action upon the cover plate, the pressure increases. This allowed
to obtain high rated values of peak current and shorting heat cur-
rent. Two contact rails may be fixed to each terminal clamp
www.nepsi.com
Technical data of the disconnectors are tabulated in table 3 on auxiliary switch type PS-3, 12 kV, 2500 A, with two operating
page 4. mechanisms NP8.”
OWD 310w.01/500
OWD 301w.02
OWD 303w.01
OWD 303w.02
OWD 310w.01
OWD 310w.02
OWD 310w.03
OWD 310w.04
OWD 320w.02
OWD 320w.03
OWD 320w.04
Specification
Unit
Rated voltage [kV] 1,2 3,6 12 24
Righted power frequency withstand to earth and between poles 3,5 10 35 50
[kV]
voltage between contacts 3,5 12 45 60
to earth and between poles [kV] - 40 75 125
Lightning impulse withstand voltage
between contacts - 46 85 145
standard model N3 [A] 2000 4000 2500 4000 2500 2000 1600 2500 2000 1600
www.nepsi.com
– for manual and motor drive operating mechanism [kg] 38 76 58 79 90 64 72
Disconnector
– with one pneumatic operating mechanism - 82 64 85 92 70 78
mass
– with two pneumatic operating mechanisms - 88 70 92 95 76 85
Minimum isolating gap between contacts [mm] 45 75 130 250
Maximum distance of first bracket at rated peak current [mm] 335 300 260 400 400 300 350
shaft extension
for auxiliary switch
for motor drive UEMC40A_ and manual drive HE
Indoor disconnectors type OWD 3,6–24 kV
holes
Un In dimension
Type terminals:
[kV] [A] A B C D E F G H I J K L M N P R
material: copper
OWD 310w.01 12 4000 300 775 880 990 185 785 310 1110 375 280 335 20 560 130 490 130 coating: silver
OWD 310w.02, 2500, 2000,
12 300 775 880 990 160 760 310 1110 360 280 330 15 535 130 410 130
03, 04 1600
OWD 303w.01 3,6 4000 260 695 880 910 185 705 290 985 320 260 280 20 485 75 470 130
OWD 303w.02 3,6 2500 260 695 880 910 160 680 272 985 305 242 275 15 445 75 372 130
Dimensional drawings
OWD 210w.01 12 4000 300 475 580 690 185 485 310 810 375 280 335 20 560 130 490 130
holes
OWD 210w.02, 2500, 2000,
12 300 475 580 690 160 460 310 810 360 280 330 15 535 130 410 130
03, 04 1600
OWD 203w.01 3,6 4000 260 435 540 650 185 445 290 725 320 260 280 20 485 75 470 130
holes
shaft extension
for auxiliary switch
Un In dimension
Type
[kV] [A] A B C D E F G H I J K L M N P R S T terminals:
material: copper
OWD 310w.01 12 4000 300 775 880 1002 193 590 310 375 550 280 335 20 560 130 490 185 1122 130
coating: silver
OWD 310w.02, 2500, 2000,
12 300 775 880 1002 193 550 310 360 550 280 330 15 535 130 410 160 1122 130
03, 04 1600
Dimensional drawings
OWD 303w.01 3,6 4000 260 695 800 922 193 590 290 320 550 260 280 20 485 75 470 185 997 130
OWD 303w.02 3,6 2500 260 695 800 922 193 550 272 305 550 242 275 15 445 75 372 160 977 130
OWD 210w.01 12 4000 300 475 580 702 193 590 310 375 550 280 335 20 560 130 490 185 822 130
OWD 210w.02, 2500, 2000, holes
12 300 475 580 702 193 550 310 360 550 280 330 15 535 130 410 160 822 130
03, 04 1600
OWD 203w.01 3,6 4000 260 435 540 662 193 590 290 320 550 260 280 20 485 75 470 185 737 130
holes
OWD 203w.02 3,6 2500 260 435 540 662 193 550 272 305 550 242 275 15 445 75 372 160 737 130
OWD 110w.01 12 4000 175 280 402 193 590 310 375 550 280 335 20 560 130 490 185 522 130
Earthing clamp
OWD 110w.02, 2500, 2000, material: steel
12 175 280 402 193 550 310 360 550 280 330 15 535 130 410 160 522 130
03, 04 1600 coating: tin
OWD 103w.01 3,6 4000 175 280 402 193 590 290 320 550 260 280 20 485 75 470 185 477 130
OWD 103w.02 3,6 2500 175 280 402 193 550 272 305 550 242 275 15 445 75 372 160 477 130
OWD 320w.02, 2500, 2000,
24 350 875 980 1167 258 550 410 425 565 380 395 15 710 250 510 160 1352 145
03, 04 1600
Provided by Northeast Power Systems, Inc.
www.nepsi.com
Drawing No. OW4/09.02
Indoor disconnectors type OWD 3,6−24 kV
with two pneumatic operating mechanisms
holes
terminals
material: copper
coating: silver
Dimensional drawings
Un In dimension
Type
[kV] [A] A B C D E F G H I J K L M N P R S holes
contact
Dimensional drawings
terminals:
material: copper
coating: silver
Earthing clamp
material: steel
coating: tin
Un In dimension holes
Type
[kV] [A] A B C D E F G H I J K L M N P
OWD 301w.02/1 1,2 2000 160 480 580 400 160 480 272 335 372 242 145 15 270 45 32
OWD 101w.02/1 1,2 2500 160 280 400 160 160 272 335 372 242 145 15 270 45 42
Provided by Northeast Power Systems, Inc.
www.nepsi.com
Drawing No. OW4/11.02
shaft extension
for auxiliary switch
for manual operating mechanism type NRWO4-3
Indoor disconnectors type OWD 3,6−24 kV
holes
terminals:
Un In dimension material: copper
Type coating: silver
[kV] [A] A B C D E F G H I J K L M N P R
OWD 310w.01/1 12 4000 300 775 880 990 185 785 310 1110 375 280 335 20 560 130 490 130
OWD 310w.02, 03, 2500, 2000,
12 300 775 880 990 160 760 310 1110 360 280 330 15 535 130 410 130
04/1 1600
OWD 303w.01/1 3,6 4000 260 695 880 910 185 705 290 985 320 260 280 20 485 75 470 130
Dimensional drawings
OWD 303w.02/1 3,6 2500 260 695 880 910 160 680 272 985 305 242 275 15 445 75 372 130
holes
OWD 210w.01/1 12 4000 300 475 580 690 185 485 310 810 375 280 335 20 560 130 490 130
OWD 210w.02, 2500, 2000,
12 300 475 580 690 160 460 310 810 360 280 330 15 535 130 410 130
03, 04/1 1600 holes
1. Operating conditions turn. This lever is for coupling with operating mechanism type
The disconnectors are meant for operation indoors, in temperate NRWO4/...−3 and with a lever arm which is an extension of the oper-
climate conditions, at surrounding temperatures ranging from ating lever, meant for driving the disconnector by means of an
−5°C to +40°C. When installing the switches in other conditions, it insulating stick. In the case of disconnectors with motor operating
is necessary to consult the manufacturer. mechanism UEMC40A_ there is no lever. Instead, there is an assem-
bly of bevel gear linking with the operating mechanism.
2. Designations and switch types The disconnectors may be equipped with an auxiliary switch (type
OWIII 20 /6 UD -2 /160 PS-3 or PS-O) coupled with the apparatus, located on the end of the
Type of Rated Rated Type of Type of Pole shaft opposite to the operating mechanism. Standard number of aux-
discon- voltage current earthing insulator distance iliary switch contacts is 12 (6NO+6NC).
nector switch
7,2 – 7,2 kV 6 – 630 A UD – lower 1 – ceramic Specified
10 – 12 kV 8 – 800 A earthing 2 – resin only for pole 5. Technical data
17,5 – 17,5 kV 10 – 1000 A switch distances The technical data of disconnectors are tabulated in the table 4 on
20 – 24 kV 12 – 1250 A UG – upper other than pages 14-15.
www.nepsi.com
3. Design and operation The apparatus, for the duration of its technical lifetime, i.e. 1000
Disconnectors type OWII are the vertical break disconnectors. The operations, does not require spare parts. On the user’s request,
disconnectors base is made as a welded steel frame. The frame spare parts may be supplied for those damaged during random
together with the disconnector shaft and the limiters of the angle events, however, their replacement should be consulted with the
of rotation forms a non-dismountable unit. The base carries the manufacturer each time, and made by ABB service or by employ-
insulators which support the main circuit consisting of two fixed ees of other companies who have been trained by the
contats and one moving contact in each pole. The moving con- manufacturer.
tacts are connected with the disconnector shaft by means of
insulating pull rods which transfer the rotation of the shaft to the 8. Information to be given with orders
moving contacts bringing them in sweep motion in the plane per- The following information should be given with order: product full
pendicular to the disconnector base. name, rated voltage, rated current and type of the apparatus.
The intrepole isolation is an air gap. In models with a smaller inter- Operating mechanisms for the disconnectors should be ordered
pole scale, the air gap is further assisted by isolating plates. separately.
The disconnectors may be opened and closed by the following
operating mechanisms: 9. Examples of orders
− manual: type NRWO4/...−3 or HE, 1. A
disconnector for rated voltage 24 kV, rated current 630 A,
− pneumatic, type NP9, equipped with lower earthing, with ceramic insulators:
− motor, type UEMC40A_, “Three pole indoor disconnector, 24 kV, 630A with lower earth-
− insulating stick. ing switch, type OWIII 20/6UD−1”.
The disconnectors, equipped with manual, motor or pneumatic 2. A
disconnector for rated voltage 24 kV, rated current 630 A,
operating mechanism, may operate in horizontal or vertical posi- equipped with upper earthing switch, with resin insulators, with
tion (driven by insulating stick – only in vertical position). pneumatic operating mechanism type NP9 assembled on the
The construction of disconnectors allows for the addition of earth- left hand side: “Three pole indoor disconnector, 24 kV, 630 A
ing switches. Earthing switches may be located on pivot side with upper earthing switch, type OWIII 20/6UG−2 + NP9 on the
(lower earthing switches) or on opening (upper earthing switches). left”.
At the base of the disconnector there is an earth terminal with
M12x40 screw. Between the disconnector shaft and the earthing 10. Dimensional drawings
switch shaft, there is a mechanical interlocking ensuring the – OW3/10.01,
proper order of switching. – OW3/11.01,
– OW3/12.01,
4. Equipment – OW3/13.01,
Disconnectors type OWIII are equipped with an operating lever set on – OW3/14.01.
the shaft, which can be moved every 10° within the limits of a full
OWIII10/6UG-2/125
OWIII10/6UD-2/125
OWIII10/10UG-1
OWIII10/10UG-2
OWIII10/12UG-1
OWIII10/6-2/125
OWIII10/10UD-1
OWIII10/10UD-2
OWIII10/12UD-1
OWIII7,2/6UG-1
OWIII7,2/6UD-1
OWIII10/6UG-1
OWIII10/6UG-2
OWIII10/8UG-1
OWIII10/8UG-2
OWIII10/6UD-1
OWIII10/6UD-2
OWIII10/8UD-1
OWIII10/8UD-2
OWIII10/10-1
OWIII10/10-2
OWIII10/12-1
Type
OWIII7,2/6-1
OWIII10/6-1
OWIII10/6-2
OWIII10/8-1
OWIII10/8-2
Rated voltage [kV] 7,2 12
Frequency [Hz] 50
to earth and 20 28
Righted power frequency between poles
withstand voltage [kV] between contacts 23 32
Rated continuous current [A] 630 630 800 1000 800 1000 1250
www.nepsi.com
Rated peak withstand current [kA] 40 80 63 40 80 80 63 63 80
Rated short-time withstand
1s 16 31,5 25 16 31,5 31,5 25 25 31,5
current [kA]
Disconnector mass / mass disconnector 24/32 31/39 25/35 23/31 31/39 31/39 25/35 25/35 50/59
with earthing switch [kg]
Maximum distance of first bracket
400 600 400 600
at rated peak current [mm]
OWIII20/10UG-1
OWIII20/10UG-2
OWIII20/12UG-1
OWIII20/6-2/160
OWIII20/10UD-1
OWIII20/10UD-2
OWIII20/12UD-1
OWIII20/6UG-1
OWIII20/6UG-2
OWIII20/8UG-1
OWIII20/8UG-2
OWIII20/6UD-1
OWIII20/6UD-2
OWIII20/8UD-1
OWIII20/8UD-2
OWIII17,5/12-1
OWIII 20/10-2
OWIII17,5/6-1
OWIII20/10-1
OWIII20/12-1
Type
OWIII20/6-1
OWIII20/6-2
OWIII20/8-1
OWIII20/8-2
OWIII30/12UG-2
OWIII30/16UG-2
OWIII30/12UD-2
OWIII30/16UD-2
OWIII30/6UG-2
OWIII30/6UD-2
OWIII30/12-2
OWIII30/16-2
OWIII30/6-2
Type
www.nepsi.com
current [kA] 3s 20 - -
Disconnector mass / mass disconnector with
78/90 90/104 90/104
earthing switch [kg]
holes
holes
Dimension
Type
A1 A2 A3 A4 A5 A6 B1 B2 B3 C1 C2 C3 C4 C5
OWIII 7,2/6-1 300 260 354 – – 220 455 248 – 700 510 480 160 190
OWIII10/6,8,10-1 300 260 354 – – 220 455 248 – 780 590 560 200 190
OWIII 10/6,8,10-2 300 260 355 – – 220 455 263 – 780 590 560 200 190
OWIII 10/6-2/125 300 260 355 93 485 220 455 263 494 630 440 410 125 190
OWIII 10/12-1 335 295 463 – – 255 472 250 – 780 590 560 200 190
OWIII 17,5/6-1 400 360 454 – – 320 654 353 – 930 610 580 210 255
OWIII 17,5/12-1 435 395 563 – – 355 677 355 – 990 670 640 240 255
OWIII 20/6,8,10-1 400 360 454 – – 320 654 353 – 1060 740 710 275 255
OWIII 20/6,8,10-2 400 360 455 – – 320 654 360 – 1060 740 710 275 255
OWIII 20/6-2/160 400 360 455 153 705 320 654 360 764 830 510 480 160 255
OWIII 20/12-1 435 395 563 – – 355 677 355 – 1060 740 710 275 255
OWIII 30/6-2 550 510 594 – – 460 875 456 – 1460 950 920 360 370
OWIII 30/12-2 565 525 716 – – 460 925 460 – 1460 1020 990 390 370
OWIII 30/16-2 565 525 716 – – 460 925 460 – 1460 1020 990 390 370
holes
holes
Dimension
Type
A1 A2 A3 A4 A5 A6 A7 B1 B2 B3 C1 C2 C3 C4 C5
OWIII 7,2/6UD-1 300 260 354 – – 541 220 455 248 – 700 510 480 160 190
OWIII10/6,8,10UD-1 300 260 354 – – 541 220 455 248 – 780 590 560 200 190
OWIII 10/6,8,10UD-2 300 260 355 – – 541 220 455 263 – 780 590 560 200 190
OWIII 10/6UD-2/125 300 260 355 93 485 541 220 455 263 494 630 440 410 125 190
OWIII 10/12UD-1 335 295 463 – – 541 255 472 250 – 780 590 560 200 190
OWIII 17,5/6UD-1 400 360 454 – – 736 320 654 353 – 930 610 580 210 255
OWIII 17,5/12UD-1 435 395 563 – – 736 355 677 355 – 990 670 640 240 255
OWIII 20/6,8,10UD-1 400 360 454 – – 736 320 654 353 – 1060 740 710 275 255
OWIII 20/6,8,10UD-2 400 360 455 – – 736 320 654 360 – 1060 740 710 275 255
OWIII 20/6UD-2/160 400 360 455 153 705 736 320 654 360 764 830 510 480 160 255
OWIII 20/12UD-1 435 395 563 – – 771 355 677 355 – 1060 740 710 275 255
OWIII 30/6UD-2 550 510 594 – – 967 460 875 456 – 1460 950 920 360 370
OWIII 30/12UD-2 565 525 716 – – 982 460 925 460 – 1460 1020 990 390 370
OWIII 30/16UD-2 565 525 716 – – 982 460 925 460 – 1460 1020 990 390 370
www.nepsi.com
Terminals: Earthing clamp
material: copper material: steel
coating: silver coating: tin
holes
Dimension
Type
A1 A2 A3 A4 A5 A6 A7 B1 B2 B3 C1 C2 C3 C4 C5
OWIII 7,2/6UG-1 300 260 354 – – 541 220 455 248 – 700 510 480 160 190
OWIII 10/6,8,10UG-1 300 260 354 – – 541 220 455 248 – 780 590 560 200 190
OWIII 10/6,8,10UG-2 300 260 355 – – 541 220 455 263 – 780 590 560 200 190
OWIII 10/12UG-1 335 295 463 – – 541 255 472 250 – 780 590 560 200 190
OWIII 17,5/6UG-1 400 360 454 – – 736 320 654 353 – 930 610 580 210 255
OWIII 17,5/12UG-1 435 395 563 – – 736 355 677 355 – 990 670 640 240 255
OWIII 20/6,8,10UG-1 400 360 454 – – 736 320 654 353 – 1060 740 710 275 255
OWIII 20/6,8,10UG-2 400 360 455 – – 736 320 654 360 – 1060 740 710 275 255
OWIII 20/6UG-2/160 400 360 455 519 705 736 320 654 360 764 830 510 480 160 255
OWIII 20/12UG-1 435 395 563 – – 771 355 677 355 – 1060 740 710 275 255
OWIII 30/6UG-2 550 510 594 – – 967 460 875 456 – 1460 950 920 360 370
OWIII 30/12UG-2 565 525 716 – – 982 460 925 460 – 1460 1020 990 390 370
OWIII 30/16UG-2 565 525 716 – – 982 460 925 460 – 1460 1020 990 390 370
max. 1030
Dimension
Type
A7
OWIII 10/6-1 OWIII 10/6UD-1 OWIII 10/6UG-1 306
OWIII 10/6-2 OWIII 10/6UD-2 OWIII 10/6UG-2 306
OWIII 10/6-2/125 – – 306
OWIII 10/16-1 OWIII 10/16UD-1 OWIII 10/16UG-1 286
OWIII 20/6-1 OWIII 20/6UD-1 OWIII 20/6UG-1 291
OWIII 20/6-2 OWIII 20/6UD-2 OWIII 20/6UG-2 291
OWIII 20/6-2/160 OWIII 20/6UD-2/160 OWIII 20/6UG-2/160 291
OWIII 20/12-1 OWIII 20/12UD-1 OWIII 20/12UG-1 276
OWIII 30/6-2 OWIII 30/6UD-2 OWIII 30/6UG-2 261
OWIII 30/12-2 OWIII 30/12UD-2 OWIII 30/12UG-2 261
OWIII 30/16-2 OWIII 30/16UD-2 OWIII 30/16UG-2 261
www.nepsi.com
– NO5 electromagnetic locking device (optional) – rated voltage
2. Operating conditions 24/110/220 V DC
NRWO4... operating mechanisms may be installed in indoor distri- – PS-3 or PS-O auxiliary switch (optional), number of contacts: 12,
bution devices. 10, 8, 6
90°
193
71 85
309
6
-
80±5
NRW04-3.../.../PSO(10) NRW04-3.../.../PSO(8)
350
000
x2
220
170°
160
www.nepsi.com
R72 W
R9
0
259
-
° 35 48 A
115
NRW04-3.../.../PSO(6) NRW04-3.../.../NO2
118
103
161
137
-
4xØ
10. 50
5
48
292
W
125
135
1:5
-
NRW04-.../BM/...
36
M12x25-5.8
92
NRW04-.../BE/...
~200
-
NRW04-.../NO5/...
NRW04-3-P... NRW04-3-L...
Locking device may be installed on the reverse side of the operating mechanism.
67
-
* Rated current is the current under normal working conditions. max. 290
** Max. current is the current for a stalled load from the motor operating device.
70
ø 25 splined
Secification Unit UEMC 40 UEMC 40
www.nepsi.com
A1 A2 B1 B2
Torque: [Nm] 200 200 300 300
Weight: [kg] 14,5 14,5 12,5 12,5 30
Contactors: 240
Closing power: [W] 3 3 3 3
Holding power: [W] 3 3 3 3
Shortest control pulse [s] 0,1 0,1 0,1 0,1 Coupling ring UEMZ 452
Operating angle: degr. 190 190 110 110 Increases the operating angle to 210° for motor operating devices
degr. 2101) 2101) - - UEMC 40 A_
1) With accessory: Coupling ring UEMZ 452
www.nepsi.com
Typ Circuit diagram
UEZJ 1 - 24 V DC 31 UEMC 141
UEZJ 1 - 48 V DC 31 UEMC 141
UEZJ 1 - 60 V DC 31 UEMC 141
Auxiliary contact for m.c.b. UEZJ 1 - 110 V DC 31 UEMC 141
- STO S 2-S/H UEZJ 1 - 125 V DC 31 UEMC 141
Includes 2 pcs. change-over contacts. UEZJ 1 - 220 V DC 31 UEMC 141
UEZJ 1 - 110 V AC 31 UEMC 141
I>
58
Operating box UEZJ 2-
Type Circuit diagram
UEZJ 2 - 24 V DC 31 UEMC 148 35 265
UEZJ 2 - 48 V DC 31 UEMC 148 255
REMOTE 20
OPEN CLOSED
ON/OFF
ø 25 ø 25
Adjuster coupling UEMC ZL9
Rmax 64
20 62 ø25 splined ø25 splined
40
www.nepsi.com
Joint UEMC ZL7
For transmitting the operating movement through an angle of
max 40°.
ø 25 ø 25,2
For tube diameter: 3/4” (26.9 mm)
splined 120 72
splined
Pk 16
150 33 108 50
Pg 16
Pr 22,5
20 A
15 40
C
3 x M10
www.nepsi.com
12
Type A B C V M
UEMC 40 mm mm mm Degr. Nm
UEMC40A_ with disconnector OWIII/ OWD – connection through an angle of max. 40º
1
5
2
6
I
O
.40°
max
7
3
9 8
www.nepsi.com
1 – Disconnector type OWIII...(OWD) 7 – Connection rod (L=1,3 m) 1YMX000004M0003
2 – Motor operating device UEMC40A_ 8 – Adjuster coupling UEMC ZL10
3 – Joint UEMC ZL7 9 – Auxiliary switch complete OW3 4 E01... (option)
4
4 – Operating handle 1YMX053235M0004 * NRK2/2 in case use of extension shaft (pos.5); NRK 2/1 if directly on the
5 – Extension shaft:1YMR416618M0001(optionally OWIII shaft.
for OWIII) or 1YMR417625M0001 for OWD 12 kV,
1YMR417625M0002 for OWD 24 kV 1
6 – Bevel gear NRK2*
10
* NRK2/2 in case use of extension shaft (pos.5); NRK 2/1 if directly on the OWIII shaft.
5 9 6
2 3
O
I
5
www.nepsi.com
When ordering spare parts all details on the rating plate are to be
mentioned.
(L1) (N)
X2: 1 2 3 4 5 9 10 21 22
black
red
1 21 1 11
For types : UEMC 40 A1 - 24, 48, 60, 110, 125, 220 V DC M1 – Motor
UEMC 40 B1 - 24, 48, 60, 110, 125, 220 V DC S1, S2 – Limit switches
S12 – Blocking switch for locking
(L1/+)
(L1/+) I O
brown
Brązowy red
Czerwony
1 3 5 7 13 8 14 11 9
2
S45 S45 24
F1 V3 14
1 I O
13 23
~
V5 ~
-
+
5 11 5 12
red
A1
K3
M1
A2
www.nepsi.com
1 1
Czarny
black
R1 S1 S2
2 2
R2*
4 4
K1 K2
3 3 A1 A1
- V1 K1 K2 V2
- A2 A2
V5 ~
~
21
3
F1 S12
4 22
X1: 2 4 6 12 10
(N/-) (N/-)
For types : UEMC 40 A2 - 24, 48, 60, 110, 125, 220 V DC; 110, 230 V AC; UU**)
UEMC 40 B2 - 24, 48, 60, 110, 125, 220 V DC; 110, 230 V AC; UU**)
F1 – M.c.b.
S45 – Push buttons (I and O)
M1 – Motor
K1, K2 – Operating contactors
K3 – Relay for 48‑220 V
S1, S2 – Limit switches
S12 – Blocking switch, locking
V5 – Rectifier for AC
V1-V3 – Diodes for DC
R1 – Resistor for 110‑230 V
*) R2 – Heater (to be ordered separately)
**) Detail motor and aux. voltage
For types: UEZJ 1 - 24, 48, 60, 110, 125, 220 V DC; 110, 230 V AC;
*) -110 VAC
-230 VAC
(L1) (+)
X1: 21 1 3 7 8
~
~
V5 -
+ 11 5 21 5 K1, K2 – Operating contactors
K3 – Relay for 48-230 V
2 2 A2 A2
www.nepsi.com
K2 K1 V1 K1 K2 V2
1 1 A1 A1
-
-
V5 ~
~
X1: 22 2 13 14 4 15 16 17
(N) (–)
31 UEMC 142 D
X1: 21 1 23 3 7 8
~ ~
V5 ~ V6 ~
- -
+ + 11 5 21 5
K1, K2 – Operating contactors
K3 K1 K3 K2
12 6 22 6 K3 – Relay for 48-230 V
3 3 V1, V2 – Diodes
K1 K2
4 4 V5, V6 – Rectifier only for AC
A1 R1 – Resistor for 110-230 V
R1 K3
A2
A2 A2
2 2 V1 K1 K2 V2
K2 K1 A1 A1
1 1
- -
- -
V5 ~ V6 ~
~ ~
X1: 22 2 13 14 24 4 15 16 17
www.nepsi.com
K2 K1
A2 A2 cator, open,
1 1
- V1 K1 K2 V2 green
A1 A1
H9 – Indicator for
-
V5 ~
~ fuse trippin-
X1: 22 2 13 14 4 15 16 17 20 g,yellow
(N) (-)
31 UEMC 149 E
For types: UEZJ 2_UU K1, K2 – Operating
*( *(
contactors
S4, S5 – Push buttons
(L1) (+) (L1) (+)
S6 – Remote con-
X1: 21 1 23 3 5 7 8 9 10 11 trol selector
~ ~ S4
K3 – Relay for
14 14 S5 14 H4 x1 H5 x1 H9 x1
~ ~ 48-230 V
V5 - V6 - S6 I O I O
13 13 13 x2 Yw x2 R1 – Resistor for
+ + Red x2 Gr
110-230 V
V1, V2 – Diodes
V5, V6 – Rectifier only
11 5 21 5
3 3 for AC
K1 K2 K3 K1 K3 K2
4 4 12 6 22 6 H4 – Position indi-
A1 cator, closed,
R1 K3 red
A2
H5 – Position indi-
2 2 cator, open,
K2 K1 green
A2 A2
1 1
- - V1 K1 K2 V2 H9 – Indicator for
- - A1 A1 fuse tripping,
V5 ~ V6 ~
~ ~ yellow
X1: 22 2 13 14 24 4 15 16 17 20
Clockwise closed
Alt A
F1 – M.c.b.
O I S4,S5 – Push buttons
Alarm S6 – Remote control
(+) selector
13 S4 13 13
S7 – Aux. contact for
S5
F1 S6 I O disconnector
14 14 14 S8 – Aux. contact for
earthing switch
S9 – Aux. contact for
fuse tripping
www.nepsi.com
4 4
A1 22 22
R1 K3 K2 K1
A2 21 21
2 2 A2 A2
K2 K1 V1 K1 K2 V2
1 1 A1 A1
UEZJ 1-
X1: 2 13 14 4 15 16 17
F1 S9 S8
(-)
(L1) (N)
X2: 1 2 3 4
Czerwony
9 10 5 21 22
Czarny
1 21 1
UEMC 40 A1, B1-
11 *(
M1 S12 S1 S12 S2 R2
12 2 22 2
Anti-clockwise closed
Alt B
I O (+)
Alarm S7 S9
14 S4 14 S5 14 H4 x1 H5 x1 H9 x1
S6 I O I O
13 13 13 x2 Żółty
Czerw. x2 Ziel. x2
www.nepsi.com
11 5 21 5
3 3
K1 K2 K3 K1 K3 K2
4 4 12 6 22 6
A1
R1 K3 22 22
A2
K2 K1
21 21
2 2
K2 K1
A2 A2
1 1 V1 K1 K2 V2
A1 A1
UEZJ 2-
X1: 2 13 14 4 15 16 17 20
F1 S9 S8 (-)
(-)
(L1) (N)
X2: 1 2
Czerwony
9 10 3 4 5 21 22
Czarny
UEMC 40 A1, B1, D1-
11 1 21 1 *(
M1 S12 S1 S12 S2 R2
12 2 22 2
www.nepsi.com
Power consumption [W] 14 16 16 14 16 16 15
Coil test voltage AC [kV] 2
Micro-switch test voltage AC [kV] 2
Lock operating travel Ø 11 mm [mm] 11
Pull rod travel to coupling with lock [mm] 4
Weight [kg] 1
Overall dimensions
46
42
21.5
30
;P-14W
Electromagnetic Interlock
2 x M5x50
Type NO5-220
Ø11
Un-220V DC
107.5
2 1
3 4
60
1 2
Circuit diagram
Ø45
50
88
ABB Sp. z o.o. We reserve the right to make technical changes or modi-