Professional Documents
Culture Documents
Brosur IGS 3723
Brosur IGS 3723
GE is a registered trademark of General Electric Company and is under license by Momentive Performance Materials Inc. Momentive Performance
Materials provides versatile materials as the starting point for its creative approach to ideas that help enable new developments across hundreds of
industrial and consumer applications. We are helping customers solve product, process, and performance problems; our silanes, fluids, elastomers,
sealants, resins, adhesives, urethane additives, and other specialty products are delivering innovation in everything from car engines to biomedical
devices. From helping to develop safer tires and keeping electronics cooler, to improving the feel of lipstick and ensuring the reliability of adhesives,
our technologies and enabling solutions are at the frontline of innovation.
Licensed
Products
IGS3723 two component insulating glass silicone
Colors • Avoid the use of sealants that evolve acetic acid when the cure
byproduct of such sealants may be exposed to the secondary
IGS3723 is available in black and grey.
seal.
Black: mix IGS3723A with IGS3723B
• Not recommended for water immersion applications.
Grey: mix IGS3723A with IGS3727B
Note: color is grey is called ‘Medium Grey” and is color-matched Technical Services
to SSG4607 Medium Grey 2-part structural sealant and to Additional technical information, literature, laboratory testing and
SCS2007 Medium Grey weathersealant. Color will show minor application engineering may be available upon request from MPM.
variation with change in mix ratio. Any technical advice furnished by MPM or any representative of
Typical Properties MPM concerning any use or application of any MPM product is
Uncured Properties Base IGS3723 believed to be reliable but MPM makes no warranty, expressed
Color White Thixotropic Paste or implied, of suitability for use in any application for which such
Specific Gravity 1.40 – advice is furnished.
Shelf Life 18 months (1) – IGS3723 Weight to Volume Ratio Correlation
Uncured Properties Catalyst IGS3723B
Mix Ratio
Color Black Thixotropic Paste
10.88:1 by weight 8:1 by volume
Specific Gravity 1.00 –
12.25:1 by weight 9:1 by volume
Shelf Life 12 months (1) –
13.60:1 by weight 10:1 by volume
Uncured Properties Catalyst IGS3727B
14.96:1 by weight 11:1 by volume
Color Grey Thixotropic Paste
Specific Gravity 1.0 – IGS3723 Work Life (Snap Time)
Shelf Life 12 months (1) – lower snap time limit upper snap time limit
100
Mixed Compound Properties 90
Snap Time (minutes)
IGS2723A+IGS3723B or IGS3727B 80
70 75
70
Color Black or Grey Thixotropic Paste 60 60
Specific Gravity 1.36 Mixed at 12.5:1 weight 50 45
Mix Ratio Range 8:1 to 11:1 By volume 40 40
30 30
Depends on ratio, 25
Snap Time 20-75 minutes 20 20
temp. & RH 10
Depends on ratio, 0
Tack Free Time 2X snap time 8 8.5 9 9.5 10 10.5 11
temp. & RH
Mix Ratio By Volume (part A:1)
Consistency/Sag 0.1” (2.5 mm) Non-sagging
Cured Properties (2) General Guidelines
Full Cure at Standard Laboratory Conditions
Mixing, Pumping and Dispensing
IGS3723A+IGS3723B or IGS3727B @ 12.5:1 mix ratio
Color Black or Grey IGS3723B or IGS3727B • IGS3723 should be mixed and dispensed using two-component
Hardness Points mixing equipment. These mixing / pumping systems are
43 ASTM D2240 specifically designed to meter precise proportions of A base
(type A indenter)
Ult. Tensile Strength 304 psi (2.1 MPa) and B catalyst, in a sealed environment, then mix and dispense
ASTM D412
Ult. Elongation 200% material at proper pressures and volumes to ensure thoroughly
Tear Strength 38.9 ppi (6.81 N/mm) ASTM D624, die B mixed, air-free material.
Shear Strength 130.53 psi (0.90 MPa) ASTM C961 • Consult equipment manufacturer or equipment manual for
Accelerated Weathering, Excellent, startup and shutdown procedures, operating pressures, mixing
ASTM C1369
5000 hours no degradation devices, and purging requirements.
Heat Resistance 300°F (149°C) – • Hand mixing of A base + B catalyst is not recommended,
(1) When properly stored; see section on storage. except when performing pre-use quality testing.
(2) Typical value, actual value may vary.
• When exchanging B catalyst on equipment, care should be
Limitations taken to minimize exposure to the environment in order to
• IGS3723 should only be used in the fabrication of insulating prevent premature curing of the catalyst.
glass where the dual seal method of fabrication is used. • IGS3723 is a suitable candidate for both ‘in-line’ mixing
The moisture vapor transmission rate of silicone sealants systems and “purgeless” after-the-gun mixing equipment.
is sufficiently high as to preclude their use in the fabrication Consult equipment manufacturer and/or MPM for information
of single seal insulating glass units. on mixing device options.
• Avoid using building materials intended for direct contact with • When properly mixed, the material should be a solid,
IGS3723 that will migrate fluids that can discolor the secondary homogeneous color free of any swirling or marbling of colors.
seal or degrade the PIB physical properties through solvating If incomplete mixing is noticed, cease operation until equipment
or softening. Contact Momentive Performance Materials (MPM) adjustments can be performed to ensure that complete mixing
technical services for additional information. is being attained.
P. 02
IGS3723 two component insulating glass silicone
Emergency Service
Momentive Performance Materials maintains an around-the-clock emergency service for its products.
Location Emergency Service Provider Emergency Contact Number
DO NOT WAIT. Phone if in doubt. You will be referred to a specialist for advice.
P. 03
CUSTOMER SERVICE CENTERS
Visit us at www.ge.com/silicones
THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS INC., MOMENTIVE PERFORMANCE MATERIALS USA INC., MOMENTIVE PERFORMANCE MATERIALS ASIA
PACIFIC PTE. LTD., MOMENTIVE PERFORMANCE MATERIALS WORLDWIDE INC., MOMENTIVE PERFORMANCE MATERIALS GmbH, THEIR SUBSIDIARIES AND AFFILIATES DOING BUSINESS IN LOCAL
JURISDICTIONS (collectively “SUPPLIERS”), ARE SOLD BY THE RESPECTIVE LEGAL ENTITY OF THE SUPPLIER SUBJECT TO SUPPLIERS’ STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE
APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION,
RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SUPPLIERS MAKE NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN
WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SUPPLIERS’ PRODUCTS, MATERIALS, SERVICES, RECOMMENDATIONS
OR ADVICE. AFOREMENTIONED EXCLUSIONS OR LIMITATION OF LIABILITY ARE NOT APPLICABLE TO THE EXTENT THAT THE END-USE CONDITIONS AND/OR INCORPORATION CONDITIONS CORRESPOND
TO THE RECOMMENDED CONDITIONS OF USE AND/OR OF INCORPORATION AS DESCRIBED BY SUPPLIER IN ITS PRODUCT DATA SHEET AND/OR PRODUCT SPECIFICATIONS. EXCEPT AS PROVIDED IN
SUPPLIERS’ STANDARD CONDITIONS OF SALE, SUPPLIERS AND THEIR REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS
OR SERVICES DESCRIBED HEREIN.
Each user bears full responsibility for making its own determination as to the suitability of Suppliers’ materials, services, recommendations, or advice for its own particular use. Each user must identify and
perform all tests and analyses necessary to assure that its finished parts incorporating Suppliers’ products, materials, or services will be safe and suitable for use under end-use conditions. Nothing in this
or any other document, nor any oral recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of Suppliers’ Standard Conditions of Sale or this Disclaimer, unless any such
modification is specifically agreed to in a writing signed by Suppliers. No statement contained herein concerning a possible or suggested use of any material, product, service or design is intended, or should
be construed, to grant any license under any patent or other intellectual property right of Suppliers or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of
such material, product, service or design in the infringement of any patent or other intellectual property right.
161-039-20E-GL
CDS: DataIGS3723 (07/13)