Professional Documents
Culture Documents
Datasheet 5500 en
Datasheet 5500 en
KNOW‐HOW TO PROTECT ™
WWW.RUST‐OLEUM.EU
5500 SOLVENT-FREE EPOXY
DESCRIPTION abrasive blasted or primed with Super Adhesive 3333 or 3366.
High build, solvent-free epoxy floor paint for garages, warehouses, showrooms, corridors, Steel: Remove loose rust, rust scale and deteriorated coatings by abrasive blasting to Sa 2½
indoor car parks, workshops etc. (ISO 8501-1 : 1988), blast profile max. 100 µm. For immersion purposes, prepare to Sa 3
(ISO 8501-01 : 1988), blast profile max. 75 µm.
RECOMMENDED USE
5500 is designed for application on concrete and masonry and can also be used on blasted DIRECTIONS FOR USE
steel, primarily intended for roller application and may also be applied by brush for small These products are supplied in pre-measured 'units' consisting of one can of pigmented
areas or touch-up only. A two coat 5500 System assures appropriate protection when in base material and one can of activator (5501). Stir individual components thoroughly before
contact with chemicals (see chemical resistance guide), frequent chemical cleaning or high mixing them together. Add activator to base material and mix thoroughly with a low speed
humidity and moisture conditions. Can be applied directly on properly cleaned, sound mixer.
mineral substrates, sound, well prepared previous Epoxy coatings; porous substrates should
be primed with 5401 or 5421 Impregnation Primer; very dense substrates, like ceramic tiles, APPLICATION CONDITIONS
should be primed with Super Adhesive 3333 or 3366. 5500 can be applied directly on Temperature of material between 10 and 20°C, air and substrate between 10 and 35°C and
blasted steel or blasted galvanised steel; if required primed with RUST-OLEUM 9170/9180 relative humidity below 85%. The substrate temperature must be at least 3°C above dew
Primer. point.
SURFACE PREPARATION
Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam)
cleaning in combination with appropriate detergents. Sand intact coatings to roughen the
surface slightly. The surface must be clean and dry during application.
Concrete and masonry: New concrete or masonry should dry and cure for at least 30 days
before applying the coating system. Remove laitance, loose and unsound concrete or
deteriorated coatings preferably by abrasive blasting and repair surface defects with 5180
Epoxy Reapir Mortar or Epoxy Putty 5412. Very dense and smooth concrete should be
Date issued: 24/06/2022
Available colours & pack sizes: Please refer to the respective product page on www.rust-oleum.eu for an overview of actual available colours and pack sizes.
Disclaimer: The information contained herein is to the best of our knowledge true and accurate and is given in good faith but without warranty. The user will be deemed to have satisfied him/herself independently
as to the suitability of our products for his/her own particular purpose. In no event shall Rust-Oleum Europe be liable for consequential or incidental damages. Products must be stored, handled, and applied under
conditions complying with Rust-Oleum Europe recommendations detailed within the latest copy of the product data sheet. It is the users responsibility to ensure that they have the current copy. Latest copies of the
product data sheet is available for free and downloadable from www.rust-oleum.eu or upon a request to our Customer Services department. Rust-Oleum Europe reserves the right to change the properties of its’
products without prior notification.
Rust-Oleum Netherlands B.V. Tor Coatings Ltd (Rust-Oleum Industrial) Rust-Oleum France S.A.S. N.V. Martin Mathys S.A.
Zilverenberg 16 Shadon Way, Portobello Ind. Estate 38, av. du Gros Chêne Kolenbergstraat 23
5234 GM 's-Hertogenbosch Birtley, Chester-le-Street 95322 Herblay 3545 Zelem
The Netherlands DH3 2RE United Kingdom France Belgium
T : +31 (0) 165 593 636 T : +44 (0)1914 113 146 T : +33(0) 130 40 00 44 T : +32 (0) 13 460 200
F : +31 (0) 165 593 600 F : +44 (0)1914 113 147 F : +33(0) 130 40 99 80 F : +32 (0) 13 460 201
info@rust-oleum.eu info@rust-oleum.eu info@rust-oleum.eu info@rust-oleum.eu
WWW.RUST‐OLEUM.EU