Technical Data Sheet
Jotaplast Primer
Product description
Type
[An economy modified acrylic water based sealer that provides proper foundation for interior wall topcoat
Features and benefits
Enhance Topcoat Kiing- A base coat that enhances topcoat hiding opacity.
Easy to apply - Efortless application without fuss.
Recommended use
For interior application, suitable for new buildings and repainting.
Substrate
(on concrete, masonry, plaster, brick work and soft board surfaces,
Product data
Packaging size Packing may vary from country to country according to local requirements,
Colours White
Solids by volume 36 £2 volumew
Application data
Remarks
Handle with care. Stir well before use.
Application equipment / methods
By brush, roller, airless spray or conventional spray.
Guiding data for airless spray
Nozzle tip 0.023" - 0.027"
Spray angle degrees 65-80°
Pressure at nozzle 140 - 190 kg/em? (2100 ps!)
Spreading rate per coat
Theoretical 9 ml 12 ml
Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature,
wastage during painting etc.
Recommended film thickness per coat
wet 83 um 11 um
Dry 30 um - 40 um
Fl thickness will vary and is calculated as average.Technical Data Sheet ‘SJOTUN
Jotaplast Primer Jotun Pte overt
Thinner
Water
Dilution
‘The paint is ready to use after proper stirring. If thinning is required, water may be added up to a maximum of
5%,
Conditions during application
‘The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point ofthe air,
‘measured in the vicinity of the substrate. Good ventilation is usually required In confined areas to ensure proper
drying
Drying times
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will
be affected correspondingly. The figures given in the table are typical with
Good ventlation (Outdoor exposure or free circulation of ar)
Typical flm thickness.
One coat on top of inert substrate
‘The given data must be considered as guidelines only. The actual drying time and time before recoating may be
shorter or longer, depending on the ambient temperature, film thickness, ventilation, humidity, underlying paint
system, requirement for early handling and mechanical strength etc, A complete system can be described on a
system sheet, where all parameters and special conditions could be included.
1, Recommenced data given is, for recaating with the same generic type of paint.
21 In case of multi-coat application, drying times willbe influenced by the number and sequence and by the
total thickness of previous coats applie.
33. The surface should be dry and free fram any contamination prior to application of the subsequent coat.
‘The drying time is measured by stated values:
Relative Humidity (RH) 50 %
Substrate temperature 10°C 23°C 40°C
Surface (touch) dry 2h th Osh
Hard dry ah 6h an
Dry to over coat, minimum 4h 2h in
Directions for use
Surface prepara
‘The substrate must be sound, clean, dry and free from dust, ol, grease, laitance ete, All races of form release
‘agents/curing agents must be removed. A lignt sanding with sultable abrasive material is recommended before
application. Any resulting dust/loose particles must be removed.
Recommended paint system
Primer
Jotaplast Primer : 1 coat
Topcoat
Jotaplast : 2 coatsTechnical Data Sheet ‘SJOTUN
Jotaplast Primer Jotun Pte overt
Storage
‘The product must be stored in accoréance with national regulations. Keep the containers in 2 dry, cool, well
ventilated space ane away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Tests
Volume Solids % measured according to ISO 3233:1998 (€),
Health and safety
Please observe the environmental and precautionary notices displayed on the container.
‘A Material Safety Data Sheet for the product has been issued.
Detailed information regarding nealth and safety risks and precautions for the use of this product is specified in
the product's Safety Data Sheet.
First-aid measures, refer to section 4.
Handling ang storage, refer to section 7.
Transport information, refer to section 14,
Regulatory information, refer to section 15.
Disclaimer
‘The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience, Jotun’s products are consiGered as semi-finished goods and as such, products are often
Used under concitions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
Itself. Minor product variations may be implemented in order to comply with local requirements, Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of th's document, the English (United Kingdom)
version will preva