The document outlines the steps to analyze and design a reinforced concrete frame building using STAAD Pro software. The steps include:
1) Creating a new project, selecting the frame structure type, and defining member properties and supports.
2) Applying loads including self-weight, dead, live, and pressure loads and creating load combinations.
3) Performing the analysis and checking the results including joint displacements, stresses, and forces.
4) Designing the beams and columns for concrete using the IS456 code and checking the output file which completes the analysis and design.
Sullivan, G. (2009) - Making Space. The Purpose and Place of Practice-Led Research. Practice-Led Research, Research-Led Practice in The Creative Arts, 41-65.
The document outlines the steps to analyze and design a reinforced concrete frame building using STAAD Pro software. The steps include:
1) Creating a new project, selecting the frame structure type, and defining member properties and supports.
2) Applying loads including self-weight, dead, live, and pressure loads and creating load combinations.
3) Performing the analysis and checking the results including joint displacements, stresses, and forces.
4) Designing the beams and columns for concrete using the IS456 code and checking the output file which completes the analysis and design.
The document outlines the steps to analyze and design a reinforced concrete frame building using STAAD Pro software. The steps include:
1) Creating a new project, selecting the frame structure type, and defining member properties and supports.
2) Applying loads including self-weight, dead, live, and pressure loads and creating load combinations.
3) Performing the analysis and checking the results including joint displacements, stresses, and forces.
4) Designing the beams and columns for concrete using the IS456 code and checking the output file which completes the analysis and design.
The document outlines the steps to analyze and design a reinforced concrete frame building using STAAD Pro software. The steps include:
1) Creating a new project, selecting the frame structure type, and defining member properties and supports.
2) Applying loads including self-weight, dead, live, and pressure loads and creating load combinations.
3) Performing the analysis and checking the results including joint displacements, stresses, and forces.
4) Designing the beams and columns for concrete using the IS456 code and checking the output file which completes the analysis and design.
AIM- ANALYSIS and design of a frame RCC building by staad
pro PROCEDURE- Step 1- Click the staad pro v8i software and then click new project then Space File name Location Length unit force unit Click next Step 2- Click the next and then Open structure wizard then click modal type Click finish Select frame modals click then Bay frame then Click the apply And then click and next step Step 3- Then click Then click Then click commands then support specification Then pinned click Then new tab open then close click Step 4- Then command click Then member properties Then click prismatic click Then rectangular click then Add click Then click select then Click beams parallel to click then Y click then Then assign click then Again click select then Click beams parallel to X and then Z click then Step 5- Click the command and then click Loading then Primary load New tab open then Dead load then Live load then Click add Click the assign to view Then click self weight load Then click floor then click Step 6- Then click dimension Then open new tab then Click display Then select a 1 bar of the section And select the bar and then click the new view And then Create the new window for the view Display the view in the active window Then click ok Then click And then remove and click Step 7- Then click load case 2 then click add Then floor then new tab open Then pressure value change minus 5 KN/ M sq Then range maximum 012 m Then add click Again this floor step Then click 3D rotation Then click Step 8- Then click commands and then loading then automatic load combination Then new tab open Select load combination code Select load combination category Then add then close Step 9- Command click then analysis Then perform analysis Then new tab open Then all ok Step 10- Then command click then Post analysis print then joint Displacement then ok Step 11- Then analyze then Run analyze then New tab and procedure including the tab Then go to post processing mode Then done Then ok Step 12- Then click animation Then ok Then click beam Then click Then click Then click new view Then ok Then click result Then click view value Then click beam results Then bending mid point Step 12- Again this procedure and all the check one by one line and this Step 13- Then click graphs Then click stress Then click force Then click Then click modelling Step 14- Command click Then design click Then concrete design click Then current code: IS456 Click Then click select parameters Then FC FY main, Fysec, maxmain, maxsec, minmain ,spsmain then ok Then click define parameters Then put the value to all then click to one by one Add Then FC2000 click select then Beams parallel to the X then Z FC-3000 Select click then Y then next one by one Click and assign to view Then assign then yes Step 15- And then click commands and then Design beam design column and take off Then one by one click and add Then close Then click design beam then select then beam parallel to X and Z Then click design column then select the beam parallel to Y Step 16- Then analyze then save Then go to post processing mode then done Then beam One by one select line and see new tab for details in concrete design click to see. Then click graph Then click modelling Then click analyze Then click run analysis Then view to output file Then done Then show file for mate and complete.
Sullivan, G. (2009) - Making Space. The Purpose and Place of Practice-Led Research. Practice-Led Research, Research-Led Practice in The Creative Arts, 41-65.