Professional Documents
Culture Documents
SBC Advanced Teams Practical Exam Dec 2022
SBC Advanced Teams Practical Exam Dec 2022
Advanced Teams
Practical Exam
AudioCodes Academy
https://www.audiocodes.com/services-support/audiocodes-academy
General information
• 3 Softphones and Mediant SBC are connected according to the setup in the next pages
• You are requested to configure your Mediant acting as an SBC and make test calls based on
the instructions defined in the next pages
• The configuration consists of several steps. Every step successfully accomplished will be
considered for the final score you will receive at the end of the exam
• The exam duration will be 3 hours. After this time you will be requested to stop the
configuration and tests and :
1. Save the configuration file (ini file) on the lab PC desktop. Use your name as the file name.
2. Send the file to by mail to the Instructor .
• Allowed documents to be used – AudioCodes User Manuals and training presentations
Good Luck
2
Introduction TK5
• The exam is based on a remote online environment and will be accessed by using a PC/Laptop running the
TeamViewer application to logon remotely to a Virtual PC running in the Lab Environment
• The following information is going to be used to access the different entities:
• NOTE: Wherever you see an x (red x) please replace it with the Student number o which you have been assigned
3
Introduction TK5
• In every Virtual PC you will find the 3 following softphones with the configured characteristics:
User Name /
SoftPhone Transport Port
Phone Number
4
Introduction TK6
• The exam is based on a remote online environment and will be accessed by using a PC/Laptop running the
TeamViewer application to logon remotely to a Virtual PC running in the Lab Environment
• The following information is going to be used to access the different entities:
User Name /
SoftPhone Company Transport Port
Phone Number
6
Lab Environment – TK5
Teams Direct Routing
FQDN: according to
MSFT requirement Internet
Transport Type: TLS
Listening Port: 5061
Coder: SILK only
SRTP Only Firewall
Allows DTMF as RFC
2833 only DMZ: 195.189.192.25x/25
7
Lab Environment – TK6
Teams Direct Routing
FQDN: according to
MSFT requirement Internet
Transport Type: TLS
Listening Port: 5061
Coder: SILK only
SRTP Only Firewall
Allows DTMF as RFC
2833 only DMZ: 195.189.192.14x/25
8
Instructions
• Procedure
1. Configure the Mediant SBC
2. Make calls between all the entities
3. Open Syslog and verify the connection was established as requested
Note:
• The only device that you need to configure is the SBC (10.15.1x.1) or
(10.15.11x.1)
• Don’t upload any LAB ini File
9
Teams Information
• Teams
• Based on Microsoft Teams Direct Routing
• FQDN: according to MSFT requirement
• Transport Type: TLS
• Listening Port: 5061
• Coders: Silk Only Teams
• SRTP only
• InBand DTMF based on RFC 2833
• Start Media Port: 9000
• Number Of Media Session Legs: 30
• The ITSP’s attached Linphone will ring when the following number is dialed:
• The ITSP DID: xxxx555/777x201
11
ITSP Information
12
ITSP Information
13
ITSP Information
14
IP-PBX Information
• IP-PBX Server:
• Based on MicroSIP Softphone
• IP address: 10.15.1x.20
• Transport Type: UDP
• Listening Port: 5060 MicroSIP
• The IP-PBX’s MicroSIP will ring when the following number is dialed:
• The ITSP DID: xxxx555/777x101
15
Instructions for the configuration
• Configure the following parameters on the SBC according to the instructions in the
next page:
• Basic Core Components
• Routing Rules
• Classification and Condition Rules
• Transcoding
• Message and Number Manipulation Rules
• Anything else you might need
16
Instructions for the configuration
• For all external connections don’t classify by Proxy Set (Teams, ITSP, IP-PBX)
• Check the following entities and/or existing headers for their following values (total or
partial) and classify by Classification Table:
18
Good Luck