Professional Documents
Culture Documents
LOCTITE 2422-tds
LOCTITE 2422-tds
LOCTITE® 2422™
January-2011
LOCTITE® 2422™ is designed for the locking and sealing of Cure Speed vs. Temperature
threaded fasteners which require normal disassembly with The rate of cure will depend on the temperature. The graph
standard hand tools. The product cures when confined in the below shows the breakloose strength developed with time at
absence of air between close fitting metal surfaces and different temperatures on 3/8 x 16 degreased steel nuts & bolts
and tested according to ISO 10964, pretorqued to 5 N·m.
prevents loosening and leakage from shock and vibration.
Particularly suitable for applications on less active substrates
125
such as stainless steel and plated surfaces, where
% of Full Strength on Steel
% Strength @ 22 °C
7649
75 ator
Activ 75
50 ™
r 7471
Activato 50
25 vato r
No Acti
25
0
5min 10min 30min 1h 3h 6h 24h 72h
Cure Time
0
0 50 100 150 200 250 300 350
Temperature, °C
TYPICAL PERFORMANCE OF CURED MATERIAL
Heat Aging
Adhesive Properties
Aged at temperature indicated and tested @ 22 °C
After 24 hour @ 22 °C
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m: 300
% Initial Strength @ 22 °C
3/8 x 16 steel nuts and bolts N·m 7.9 to 28.4LMS °C
150
(grade 5) (degreased) (lb.in.) (70 to 251) 250
200
200 °C
(lb.in.) (137)
200
200 °C 150 °C
Prevail Torque, ISO 10964, Pre-torqued to 5 N·m:
150
3/8 x 16 steel nuts and bolts (degreased) N·m 1.2
(lb.in.) (11)
100 233 °C
GENERAL INFORMATION
For Disassembly In case products are delivered by Henkel Belgium NV, Henkel Electronic
1. Remove with standard hand tools. Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
2. In rare instances where hand tools do not work because In case Henkel would be nevertheless held liable, on whatever legal ground,
of excessive engagement length, apply localized heat to Henkel’s liability will in no event exceed the amount of the concerned delivery.
nut or bolt to approximately 250 °C. Disassemble while In case products are delivered by Henkel Colombiana, S.A.S. the following
hot. disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
For Cleanup recommendations for use and application of the product are based on our
1. Cured product can be removed with a combination of knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
soaking in a Loctite solvent and mechanical abrasion and conditions in respect of which you use them, as well as the intended
such as a wire brush. applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
Loctite Material SpecificationLMS written or oral recommendation(s) regarding the concerned product is excluded,
LMS dated December-12, 2007. Test reports for each batch except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
are available for the indicated properties. LMS test reports product liability law.
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks of
Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark
registered in the U.S. Patent and Trademark Office.
Reference 0.2