Professional Documents
Culture Documents
Eval 3 Review Nov 2020
Eval 3 Review Nov 2020
Page 1 of 6
REVIEW INNOVATIONS 3rd Evaluation Examination CE Board November 2020
16. For the function f(x) = (x2 - 9x + 14) / (x2 – 11x + 24). 24. Determine the minimum dry unit weight of the soil if
Which of the following cannot be in the domain of f(x)? relative density is 93.67%?
A. 8 and 3 C. 7 and 2 A. 9.58 kN/m3 C. 9.46 kN/m3
B. 8 and 2 D. 7 and 3 B. 9.71 kN/m 3 D. 9.29 kN/m3
17. A combination lock has 60 different positions. To open Situation 3. A square footing of width z meters carries a load
the lock, the dial is turned to a certain number in the P that may be considered uniformly distributed and it is
clockwise direction, then to a number in the supported by a soil strata shown. The silty clay has a
counterclockwise direction, and finally to a third number compression index of 0.274. Its void ratio prior to
in the clockwise direction. If successive numbers in the application of the load is 84%. Assume that the load is
combination cannot be the same, how many different transmitted through a truncate pyramid having side
combinations are possible? slopes of 2V to 1H and that the stress is uniform across a
A. 34,220 C. 216,000 horizontal plane.
B. 205,320 D. 208,860 x = 5.5 m γ1 = 18.2 kN/m
y = 4.3 m γ2 = 10.1 kN/m
18. What is the natural logarithm of e^(xy)? z = 2.4 m γ3 = 9.4 kN/m
A. 1/xy C. 2.718/xy a = 1.8 m P = 667.2 kN
B. xy D. 2.718xy
19. The salary of an employee's job has five levels, each one
is 5% greater than the one below it. Due to
circumstances, the salary of the employee must reduce
from the top (fifth) level to the second level, which results
in a reduction of $122 per month. What is the employee's
present salary per month? Round your answer to the
nearest hundred.
A. $440 C. $680
B. $570 D. $900
22. Determine the in situ dry density of the soil? Situation 4. The result of a constant-head permeability test
A. 1437.2 kg/m3 C. 1965.1 kg/m3 for a fine sand sample having a diameter of 150 mm and
B. 1583.8 kg/m3 D. 1783.2 kg/m3 a length of 300 mm are as follows:
23. If the maximum dry density is 1885.24 kg/m3. Determine Constant-head difference = 500 mm
the relative compaction in the field? Water collected in 5 mins = 350 cm3
A. 96.11% C. 94.59% Void Ratio of sand = 0.61
B. 95.88% D. 92.87% 28. Hydraulic Conductivity in cm/sec
A. 3.78 x 10-3 C. 4.13 x 10-3
Page 2 of 6
REVIEW INNOVATIONS 3rd Evaluation Examination CE Board November 2020
B. 3.82 x 10-3 D. 3.96 x 10-3
29. Discharge Velocity in cm/sec
A. 6.60 x 10-3 C. 6.37 x 10-3
B. 6.88 x 10-3 D. 6.30 x 10-3
30. Seepage Velocity in cm/sec.
A. 0.017 C. 0.021
B. 0.019 D. 0.023
Situation 6. An open cylindrical vessel 1.3 m in diameter and 40. Find the allowable bending stress (MPa) of the beam.
2.1 m high is 2/3 full of water. If rotated about the vertical A. 176 C. 149
axis at a constant angular speed of 90 rpm. B. 164 D. 205
34. Determine how high is the paraboloid formed of the 41. Determine the allowable moment (kN-m).
water surface, in meter(s). A. 355 C. 390
A. 1.26 C. 2.46 B. 488 D. 419
B. 1.91 D. 1.35 42. 3. Compute the safe uniform load (kN) if the beam is
35. Determine the amount of water in liters that will be simply supported.
spilled out.
A. 48.7 C. 52.4
A. 140 C. 340 B. 61.0 D. 44.4
B. 152 D. 146
36. What should have been the least height of the vessel, in Situation: A W12x120 column that has a length of 4.9m. Use
meters, so that no water is spilled out? A36 steel. The ends are pinned. Properties of W12x120:
A. 2.87 C. 3.15 A=22774mm2 rx= 103.2mm ry=79.5mm.
B. 2.55 D. 2.40 According to Section 4.5.1.3.1 of NSCP, on gross section of
axially loaded compression members whose cross-sections
Situation 7. A certain fluid with a specific gravity of 1.25 meet with the provisions of the code, when KL/r, the largest
flows through a 150 mm diameter pipe with a mean effective slenderness ratio of any unbraced segment, is less
velocity of 1.2 m/s. than Cc:
37. Determine the volume flow rate (m/s).
A. 0.035 C. 0.021 (KL / r)2 Fy
Fa = 1 −
B. 0.079 D. 0.019 2Cc 2 FS
38. Determine the mass flow rate (kg/s). 3
A. 43.75 C. 23.75 5 3 KL / r 1 KL / r
FS = + −
B. 26.51 D. 98.72 3 8 Cc 8 Cc
39. Determine the weight flow rate.
A. 232.99 C. 429.19 where:
B. 968.74 D. 260.04 2π 2E
Cc =
Fy
Situation 8. An 8m W18x76 A36 steel beam has adequate
lateral support. Properties of W18x76: b f = 280mm tf = On gross section of axially loaded compression member,
17.3mm d = 462.5mm tw = 10.8mm Determine the when KL/r exceeds Cc:
following:
12π 2E
Fa =
23(KL/r) 2
Page 3 of 6
REVIEW INNOVATIONS 3rd Evaluation Examination CE Board November 2020
43. Find the critical effective slenderness ratio of the column.
A. 47.5 C. 61.6
B. 78.4 D. 68.4
44. Using NSCP, determine the allowable compressive stress
in MPa.
A. 119 C. 188
B. 251 D. 146
45. Using NSCP, determine the allowable compressive load in
kN.
A. 2710 C. 4282
B. 5716 D. 3325
Page 4 of 6
REVIEW INNOVATIONS 3rd Evaluation Examination CE Board November 2020
Situation 13. A cantilever beam 2.4 meters long is subjected to
a uniform gravity load w throughout its length. The
trapezoidal beam cross section has a 100 mm diameter hole
positioned as shown in Fig. STR-3. The allowable stress is
150 MPa in tension and 120 MPa in compression.
58. Calculate the moment of inertia of the section (in mm4)
about the x-axis.
A. 265 × 106 C. 172 × 106
B. 329 × 10 6 D. 191 × 106
59. Determine the maximum bending stress (in MPa) when the
load w is 50 kN/m.
A. 94 C. 97
B. 105 D. 87
60. Find the maximum safe load w (in kN/m).
A. 62.2 C. 69.0
B. 59.3 D. 71.6
120 mm
y
150 mm
50 mm
x
90 mm
200 mm
~o0o~
Nothing Follows
Page 5 of 6