Professional Documents
Culture Documents
InstallationManual CT07
InstallationManual CT07
INSTALLATION MANUAL
CT07
VERSION 3.3
1 General Safety Instructions
• Attention! You must read this installation manual before starting the installation!
• The Workshop / Company that is responsible for the initial installation must guarantee the proper installation for at
least 12 months
• Before beginning the installation of your product, qualified personnel (skilled in electronic/electrical installation) must
read completely this guideline. Important information contained herein is to prevent danger and damages of the used
product or vehicle.
• Do not disassemble the device. Do not touch before unplugging the power supply if the device is damaged, the power
supply cables are not isolated or the isolation is damaged.
• All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
• The device may be connected only by qualified individuals.
• The device must be firmly fastened in the predefined location.
• Warning!! May explode, if wrong accumulator is used.
• Any installation and/or handling during a lightning storm is prohibited.
• The device is susceptible to water, humidity and too much heat.
• All installations have to be completed with a function test according this manual. Instructions must not be ignored (e.g.
missing permanent power or connection to ignition) and wrong installations will cause the need of a new installation
date.
1.1 Conctact
Europe und International Middle East
Software-Management GmbH High-Tech Solutions FZ-LLC
Raiffeisenplatz 1/3c Branch office Dubai Internet City
A-4863 Seewalchen am Attersee Building 1 - Office 10 (Ground Floor)
Austria P.O. Box 502721, Dubai
Tel: +43-7662 22 3 44 United Arab Emirates
Fax: +43-7662-22 3 44 30 Tel: (+971) 4 4330906
Office hours: Mo – Thu 8 – 12 and 13 – 17, Fr 8 - 12 Fax: (+971) 4 4234915
www.gps.at Office hours: Sun – Thu 9 - 18
info@gps.at www.gps.at
info@gps.at
The recorded data is available by calling a link, also the digital inputs trigger an email. The recording ends after 24h
automatically. The tool works for all devices, that send data by a data connection. SMS is not supported. Please note that
different hardware types send data differently.
https://service.sw-management.at/BoxServer/partneradmin/
Click on the link to see the data. You can also use this link on a smartphone or tablet, if you do the installation in the vehicle!
Installation is only complete if the following mandatory test results are accomplished successfully:
TS (Timestamp): Current data is shown (check ts coloum for the timing, be aware of time zone differences, it uses
Lat / Lon /Alt (GPS Position): the gps position and altitude is shown, you could check the values by entering them in
Google Maps.
Speed: when driving speed is higher than 0.
Dig In 1 (Digital Input 1) must be 1if ignition is ON (only if ignition signal is connected to digital input 1)
Dig In 1 (Digital Input 1) must be 0 if ignition is OFF (only if ignition signal is connected to digital input 1)
Certain accessories are also shown
Drivercode: if an iButton is connected to the reader, there will be
1.14 Documentation
After finishing your installation and tests you should send a Installation Document to your customer/partner:
For a better overview the list of installed vehicles shall be summarized and handed over. Please send us a list with all the
vehicles, SIM-Card-numbers and IMEI.
IMEI of Box GSM number Vehicle name Odometer Odometer Reading Location of box /
Date special remarks
We recommend to fill in the vehicle service for every installation. It is an approval document that the installation was tested.
You can download it here:
http://www.gps.at/downloads/vehicle_service_form.doc
2 Datasheet
Recharging can be done via USB-to-PC or the 220Volt-to-USB adapter plug or USB-to-cigarette lighter plugs that are available for
common mobile phones (not included).
3.3 Powerconsumption
Depending on the configuration, akku state, position,… it can send from a few minutes up to weeks. Almost everything related
to the energy management are configure able.
3.4 LED’s
LED Status Description
Yellow GSM OFF no GSM signal, GSM offline
ON Active GSM connection
Flashing After switching on for a few seconds
Green GPS OFF GPS is switched off or in sleep mode
ON GPS is switched on, but has NO valid GPS signal fix
Flashing GPS is switched on AND has GPPS signal is OK
RED Charge OFF If connected to charger it is fully recharged
ON If connected to charger, it is charging
Blue Motion Flashing Panic alert was activated
LED BatLow OFF Battery level is OK
ON Recharging the battery is necessary
The SIM settings are pre-configured already. If you provide us the SIM before delivery, we will add the SIM inside for you. Else
you must unscrew the device, open it carefully and insert the SIM card. The SIM must be without SIM lock and active for GPRS
and SMS.
When you charge the device in a car or bring it outside after charging, it must within a few minutes in the software and show the
battery level in percentage in the asset vehicle details. A battery level below 12- 15% is critical and needs to be recharged. If
you have problems, contact our support!
4 Trouble-Shooting
Also read the section trouble-shooting in the first section of this document!