Professional Documents
Culture Documents
Mando Universal
Mando Universal
ROLLING DUPLICATING PROCEDURES FAAC /GENIUS (FAAC SLH 433-868/ GENIUS 868)
Whie pressing the button1 ofthe "v15.0, press 4 times the button 2. Release bath ATTENTION, PLEASE: Verify that the remote control is a MASTER. Pressing any buttons, the
buttons. Now the LED of the WHY emits a quick flsh every 2 sec.
LED should issue a double flash rather than switch on as a fixed light.
2) Place the original remote control in front ofthe "V1s.0", at about 4-60 cm of 1) While pressing the button 1 ofthe "EVO15.0", press 4 times the button 2. Release
distance. both buttons. Now the LED of the WHY emits a quick flsh every 2 sec.
SPressandretainpressedthe buttonofthe original remote control that you want to 2)Predispose the FAAC remote control for the emission of the seed code (by pressing
copy until the V15.0's led will turn on with a light and then emits a double flash every 2 simultaneously the buttons 2 and 3)
sec.
3) While the FAAC LED is flashing. place it in front of the "V15.0", at about 4-60 cm of
3) Transmit now the seed code of the original remote control (by pressing the rear hide distance and press the button that you want to copy until the V15.0's led will change
button or the buttons 1 and 2 simultaneously in the new models)
frequency of flashing (faster than before), as a confirmation of the correct copy of the
4) Now the LED will flsh quickly, press the button of the "V15.0" where you wa nt to code
store the code just copied, until the LED will turn off. 4) While the LED is flashing, press the button of the "V15.0" where you want to store the
5) Now activate the procedure to insert the new remote control on the receiver. code just copied, until the led will turn of.
BFT V2
1.While pressing the button 1 ofthe "V15.0", at the same time press 4 times the 2
button. 1) Press and hold button 1 and press button 2 four times at same time,Release 2 buttons
2. Reiease both buttons. Now the V15.0 LED will emit a short filash every 2 seconds. till LED flashed once every three seconds
3.Place the original remote control to be programmed in front of the "Vi5.0", at about u t o i g i n a l remote in the front of new remote (a bout 4-60cm), press and hold the
-60 cm of distance original remote button which need to be copied until the LED wil turn on with a fixed
4. Press and retain pressed the button to be progra mmed ofthe originai remote ight and then emits a double flash very2 secondsS
Control, till the LED will switch on 3) Press and hold once again the same button of original remote, the LED of new remote
as a fix light; now release the button. will flashes quickly, press the button that
you want to save the code, unitl the LED off
S.The Vis.0 LED will emit a s hort flash every 2 seconds 4) Now active the remote with AMC procudure
6.Yransmit now the SEED CODE ofthe BFT original remote control, press the hidden
buttons until the original remote control LED switches on. ERREKA
7.Nowthe V15.0 LED will change the flash mode (more fast), for a reconfirmation of the ERREKA has three difterent cloning modes. If you cannot clone, please contact us
cOrrect code learning. This step may take some seconds.
e.At this moment, press the new remote
Compatible List
Brand Model
arand Model
2,TX2 COLOR, 1X4
KEY 900TXB 42R, SUB44, TXE 44R, IXG 44R
ADYK
TE4433H BLUF, 433 iG BRAVO
KINGGATES SMO, CPPER
COAPACTHY-DOM, 1/ERCURI B, MERCURI C, SABU 1ON, 1MARS,SAIURN, 2/N, HRRA KE ING KUA, KUAE, KUAS
iMP 1,11MP-2, UNITECH
SPYCO, RIW4E
|LABtl
LMAIIC(AMC) BROWN, bROVWIN RLD, LRO OVER,
PASS, MINIi ASS, TECH3, FOR4 1MW