Professional Documents
Culture Documents
802P Universal Indicator Manual 350
802P Universal Indicator Manual 350
802P
MAKE ALTOP
USER MANUAL
Corporate Office :
165, GIDC Makarpura,
VADODARA - 390 010.
Tel. : (0265) 2643550, 2646021
Fax : +91 (0265) 2641054
Email : support@altopindustries.com
www.altopindustries.com
INTRODUCTION
Altop make UNIVERSAL INDICATOR, model 802 P is design to accept all kind of
inputs like [mA , 0-10 V DC , 1- 5 V DC ,0-150 mV , T/C type (K ,J , R , S , T ,C ,B ,E ),
Cu-53, OHMS, RTD Pt-100] and gives 4 digit seven segment red LED display. Universal
Indicator can give max. 2 Nos. Relay contacts O/P & 4 - 20 mA DC retransmission O/P,
if required.
The instrument employs low drift precision components for long trouble free operation.
SPECIFICATION
Transmitter 24 V DC @ 30 mA
power
Power Supply 230 V AC / 110 V AC / 24 V DC (Predefined)
Ambient Temp. 50 C
96 mm (H) * 96 mm (W) * 110 mm (D)
Dimension 48 mm (H) * 96 mm (W) * 110 mm (D)
72 mm (H) * 72 mm (W) * 110 mm (D)
1.
INSTALLATION
The Universal indicator is shipped in shockproof packing. Unpack the instrument and
check for visible damage , if any. If any damage is observed or loose material is sensed
in the instrument, do not switch it on before the defect is set right.
The instrument is design for mounting on panel. It required cut out of 92 mm (H)
92 mm (w). / 44 mm (H) x 92 mm.
All field terminations are done at the back of the instrument. Two terminal strips are
provided for the termination. The connections are made as per the details below.
TERMINAL DETAIL
2.
Universal Input Connection details
All T/Cs
4 - 20/ 0 - 20 mA DC
C C
B B
- -
A/- A/- Thermocouple
T/C Input 4 - 20/ 0 - 20 T/C
+ mA DC From the + input
Vo Vo +
+ + source +
mA mA
+ +
TPS TPS
+ +
CJC CJC
- -
CJC CJC
+ +
0 - 10 / 1 - 5 V DC Rtdpt-100
B/+ and
C Short
C C
+
B B Rtd pt-100
- input
A/- A/-
T/C Input 0 - 10/ 1 - 5 T/C -
+ V DC +
Vo + Vo
+ +
mA mA
+ +
TPS TPS
+ +
CJC CJC
- -
CJC CJC
+ +
3.
Predefine Input Connection details
+
I/P
+ Predefine Input
I/P From the field
-
TPS -
+
TPS
-
CJC
+
CJC
-
If input is Rtdpt-100
B/+ and C
C Short +
B Rtd pt-100
input
A/-
-
4.
OPERATION
THERE ARE FOUR BASIC MODES OF OPERATION.
(1) PArA {Parameter}
(2) iPty {Input Type}
(3) iPCL {Input Calibration}
(4) oPty {Output Type}
(5) oPCL{ Output Calibration}
(6) nEUP {New Password}
(7) Id {Instruments Id}
5.
Front Key description
5
Function key F is used to enter into
F MEnU . It is also used as a Escape key.
5 5
Enter key is used to store the new value
set.
It is also used to enter into the particular
mode or parameter.
5 5
Up key is used to increment the value.
It is also used to scroll the different
parameters as well as different modes.
5
Pass/Back key is used to pass through
6.
OPERATION FLOW CHART
F
9
PASd
95 PArA
0000 Decimal Point 48 9
9 5 for Liner 3 dP 3
4
3 PArA 3
input only
48 95
48 95 ZErO
IPty 48 95
48 95 SPAn
IPCL 48 95
48 95 SP1
oPty 48 95
48 95 HyS1
oPCL 48 95
48 95 SP2
nEUP 48 95
48 95 HyS2
4 Id 4 48 95
5 ALr1
5
89
4 ALr2 4
7.
g All modes are password protected. Factory set password is 0000.
g In Parameter mode, using up key & pass key, user can set zero,
span, decimal point, setpoint1, setpoint2, hysteresis1, hysteresis2,
alarm1 type, alarm2 type as desire.
g Instrument will display the process value as per set zero & span
value.
Also give the output low & output high as per set zero & Span value.
g DP (Decimal Point) parameter will appear only for mA, 0-10 V DC,
1-5 V DC, mV, & OHMS inputs.
NOTE :- Press enter key to store the new value set. Otherwise
new value wont be stored.
8.
IPty
9 44
5
4 9
mA
48 95
0-10
48 95
1-5
oHM
48 95
K-tC
4 9
t-tC
48 95 48 95 48 95
mV J-tC b-tC
48 95 48 95 48 95
Cu53 r-tC E-tC
48 95 48 95
8 5 C-tC
S-tC
48 95
8 5 rtd
54
g In Input type mode, user can configure the input type as required.
Press enter key to store the new input type.
When enter key will be pressed, instrument will come out in input
type mode.
9.
IPCL oPCL
FOR T/C
9 5
oPty 4
3
953
CJC OPL1
INPUT ONLY
48 95 95 48 95
IP_L 3 Lin OPH1
48 95
48 95
4 Sqrt
89
5 IP_H
5 OPL2
48 95
4 OPH2 4
5
g In output type mode, user can select the Liner or square root for
outpu signal as well as display.
10.
NOTES:-
g Whenever input type is changed, no need to calibrate the
input again.
Also, no need to calibrate output, once calibrated..
00C to 17600C
R Type T/C
S Type T/C 00C to 17000C
-1000C to 10000C
E Type T/C
C Type T/C 00C to 23150C
11.
nEUP
9
5
0000
9
5
COnF
g In New password mode, using up key & pass key user can set the
new password.
Once new password is set, press enter key.
Now display will show new password mode.
12.
AL-1
AL-2
AL-3
AL-4
F
www.altopindustries.com
In normal screen , the display will show the current process value
& gives the output accordingly.
In normal screen , by pressing pass key user can view the setpoint1
& by pressing Up key user can view the setpoint2.
13.
Connection diagram of 2 wire transmitter with instrument
Transmitter
+ -
1 2 3 4 5 6 7 8 9
14.