Professional Documents
Culture Documents
Well Control
Well Control
The influx is in general circulated with reduced flow rate compared to drilling flow rate.
The slow pump rate is estimated between the quarter to half of drilling flow rate. There
are many benefits of selecting such reduced rate:
Limited pressure on bottom by reducing the friction losses in the annular space
Give the choke operator the ability to adjust the pressures and react effectively in
Take in consideration the mud gas separator capacity to treat the kick
Driller’s Method
mud is not added to the first circulation. The drillpipe pressure will
therefore not decrease during the first circulation (see figure below).
The purpose of the first circulation is to remove the kick fluid from the
ً اثناء عملٌات الحفر االعتٌادٌة وكما هو موضح فSPM توفٌر مخطط الضغط مع معدل الضخ •
: ًالشكل التال
ً والضغط ف, بعد حصول الرفسة وغلق مانعات االندالع ٌتم تسجٌل الضغوط على انبوب الحفر •
Initial بعد استقرارهما ومن ثم حساب الضغط االبتدائً عند سرعة القتل, ًالتجوٌف الحلق
constant bottom hole pressure which is equals to pore pressure. The initial
Where
.ضبط سرعة المضخة عند سرعة القتل مع الحفاظ على ضغط التجوٌف الحلقً ثابتا •
عند الوصول الى سرعة القتل ٌتم قراءة ضغط انبوب الحفر ومن ثم المحافظة علٌه اثناء عملٌة •
عند اتمام عملٌة ازاحة الفقاعة الى الخارج ٌتم قراءة ضغط البطانة ومقارنته مع ضغط انبوب الحفر •
المسجل فً الخطوة . 1-حٌث ان الضغطٌن ٌجب ان ٌتساوٌا فً حالة خروج فقاعة الغاز بكاملها خارج
التجوٌف.
اذا كان ضغطً البطانة وانبوب الحفر متساوٌان فٌتم غلق البئر ,اما اذا كان ضغط البطانة اكبر من ضغط •
انبوب الحفر فٌجب االستمرار بالتدوٌر لحٌن اخراج فقاعة الغاز بصورة تامة وتساوى الضغطان.
**اذا تساوى ضغط البطانة مع ضغط انبوب الحفر فعندها ٌتم تحدٌد كثافة طٌن القتل من المعادلة التالٌة: •
In order to keep a constant bottom hole pressure when circulating kill mud into
the drill string, the discharge pressure has to decrease from the initial
by the friction losses into the drill string when the kill mud reaches the drill bit.
حساب عدد ضربات المضخة الالزمة الٌصال سائل القتل الى الحافرة من المعادلة التالٌة:
Time to pump from surface to bit.
-ازاحة السائل القدٌم بطٌن القتل الجدٌد الى الحافرة مع الحفاظ على ضغط البطانة ثابتا.
-عند وصول طٌن القتل الى الحافرة تتم قراءة وتسجٌل الضغط على انبوب الحفر .
ٌ -تم تدوٌر طٌن القتل الى السطح بالحفاظ على ضغط انبوب الحفر ثابتا.
-عند وصول طٌن القتل الى السطح ٌتوقف التدوٌر ٌ ,غلق البئر تتم قراءة الضغوط حٌث ٌجب ان ٌكون كل
Example:
A kick has happened and the well information recorded as the figure
Sol:
نرجع الى مخطط الضغط مع معدل الضخ الذي تم تحضٌره مسبقا لمعرفة ضغط التدوٌر عند معدل القتل
ICP=200+500= 700psi
نضبط المضخة على 30 SPMمع الحفاظ على ضغط البطانة 300 psi •
9.6+(200/0.052*10000)=10ppg
ضبط المضخة على معدل 30 SPMوالحفاظ على ضغط البطانة مساوٌا الى . 200 psi
** تدوٌر الطٌن ذو كثافة 10 ppgواٌصاله الى الحافرة ( اي بعد . ) 1420 strokes
** فً لحظة وصول طٌن القتل الى الحافرة نقرأ الضغوط على كل من البطانة وهو ٌجب ان ٌكون 300
** نستمر بالتدوٌر مع الحفاظ على ضغط انبوب الحفر بمقدار 521 psiلحٌن ازاحة الطٌن القدٌم الى
الخارج.
** اٌقاف التدوٌر ٌ ,غلق البئر ,تقرأ الضغوط وهً ٌجب ان تكون
SICP=SIDPP=0
ثم نستمر بالحفر بصورة طبيعية باستخدام طين الحفر الجديد
Wait and Weight Method
This method involves one circulation. Kill mud is prepared and is pumped
from surface to bit while following a prepared drillpipe pressure drop schedule.
Once the kill mud enters the annulus, a constant drillpipe pressure is
After the well has been secured and pressures have stabilized,
[ ]
- Once the preceding calculations are completed, plot pump pressure versus
Example
Sol:
Drill pipe Length = well depth – heavy weight pipe length – drill collar length
ـــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــــ
The total strokes required to fill the drill string = total volume of string / Mud
Drill pipe +heavy pipe - open hole length = 13536 – 9975- 900= 2661 ft …L2
Total strokes to displace the mud from Annulus = 613 / 0.1019 = 6019 stks
The pressure changes from ICP to FCP when the whole Initial mud in the
1200
1000
800
600
400
string vol
200
0
0 500 1000 1500 2000 2500 3000
STROCKS