Professional Documents
Culture Documents
Taiyo 140H-8 Tie Rod - Parker Version
Taiyo 140H-8 Tie Rod - Parker Version
United Automation
Hydraulic Cylinder
140H-8
JIS
Catalog HY08-T1151-1/NA
HA
106 70/140H-8
Catalog HY08-T1151-1/NA
7/14 MPa Double Acting
14 MPa Double ActingHydraulic Cylinder
Hydraulic Cylinder
View
Table of
Contents
High-performance cushion
built in hydraulic cylinders
General Hydraulic Cylinders
cushion adjustment.
70/140H-8
better maintainability.
Table of Contents
Table of Contents / Mounting Styles. . . . . . . . . . . . . . . . . . . . 1 CB Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 FZ Mounting Style. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Design Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FC Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
How to Order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FD Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Mounting Style Information. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CA Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Change of Rod End Shape. . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-24
SD Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Seal Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
FE (for rod A). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Theoretical Push and Pull Forces. . . . . . . . . . . . . . . . . . . . . 26
FY Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-28
LA Mounting Style. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ports and Cushions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30
TA Mounting Style. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
TC Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Fluids and Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-33
FK Mounting Style. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Cylinder Safety Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35
CS Mounting Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Offer of Sale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
CS style (cap eye with spherical bearing) CB style (cap clevis) FZ style (cap rectangular flange)
FC style (rod square flange) FD style (cap square flange) CA style (cap eye)
(for rod B/C) Cap eye mounting according to former JIS
1 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
safety measures for the cushion valve.
70/14
●Wide variety of new-type small sensors for
Catalog HY08-T1151-1/NA
better maintainability.
Product Specifications 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents Standard Specifications Terminologies
Cushioning Metal to Metal due to the inertia of load must be lower than the
maximum allowable pressure.
Petroleum-based fluid
Adaptable fluid ● The selection of packing material
(When using another fluid, refer to the table of fluid adaptability.) depends upon the working temperature
Tolerance for thread JIS 6g/6H
range. For details, refer to page 33.
● The standard type cylinders can be used up to
0 to 100mm+0.8
0 101 to 250mm+1.0 +1.25
0 0251 to 630mm 0
Tolerance of stroke the working temperature range shown in the
631 to 1000mm+1.4 +1.6 +1.8
0 1001 to 1600mm 0 1601 to 2000mm 0 selection materials by using seal material 6,
HNBR.
Standard type ………… ● Carbon steel for machine structural use
Tube material ● In case that the lock nut is attached to the
Switch Set ……………… ● Stainless steel
piston rod end thread part, increase the thread
SD • LA • FD • FE • FK • FY • FC length (dimension A).
Mounting style ● The FE style in the mounting style column can be
FZ • CA • CB • CD • TA • TC
used only for the rod A.
● Rod eye (T-end), rod eye with spherical bearing (S-end), ● For the internal structure, refer to the sectional
rod clevis (Y-end) with pin, lock nut drawings at the end of this catalog.
Accessories
● Boots : Only general purpose type
Standard : Neoprene coated nylon
Semi-standard : Gortite, Hi-temp
2 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Design Features 14 MPa Double Acting Hydraulic Cylinder
View Cushion valve
Table of Bore Ø32 to Ø100
Contents
Double acting single rod / Standard type (Rods A, B and C) 18 34 17 19
8 11 9 33 29 1 14 12 26 5 16 24
Cushion valve
Bore Ø125
18 34 17 19 18 34 35 17 19
28 27 3 23 32 31 4
3 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
How to Order 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents
The item enclosed by broken line needs not to be entered, if unnecessary. Semi-standard specification
General Purpose Type
3
od e❹
on ❺
si ❽
❼
l❷
❾
❶
t1
e
pe
ke
e
att tity
n
n
g
pe
l
ia
en
bo
itio
yl
or
us yp
tio
in
er
ty
st
hm
Ty
os
an
rb
tr
at
ep
sy
g
t
S
qu
ac
po
hi
de
or
in
lm
alv
or
R
nt
or
in
nv
t
ns
ea
ou
or
C
ns
yl
nd
hio
Se
C
P
M
S
Se
s
de
Cu
Standard type
Ro
●
140H-8 2 LA 80 B B 200 - Rc A B
● Switch Set 140H-8R 2 LA 80 B B 200 - Rc A B AH 2 - T L -X
Sensor quantity(1, 2, to n)
Sensor symbol
1) Note) Select applicable sensors
□
1 Nitrile rubber
out of the Sensor List:
□
2 Urethane rubber AF, AG, AH, AJ & AE
□
3 Fluorocarbon
□
6 HNBR ●
! Notes on ordering Switch Set
□
8 Slipper seal (Ø32 to Ø100) ● When no sensor is required, specify
0 for the sensor symbol 11 and the
Notes) The material of Slipper seal is nitrile sensor quantity 12
rubber except for the piston. Switch Set Mounting ● Sensors are not mounted on
Cylinders are not provided with Slipper seals. style cylinders at delivery.
Rod A
Cushion valve position(A, B, C, D, 0)
* Standard type:(Ø40 to Ø125)
□
A Rod A
Switch Set: (Ø40 to Ø125) □
B Rod B Port position (A, B, C, D)
Rod B/C □
C Rod C
* Standard type: (Ø32 to Ø125)
Switch Set: (Ø32 to Ø125) None Rc thread
4 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Mounting Style Information 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents
Mounting Styles: SD, LA, TC, FK ,CB, FZ, FD, CA, TA Mounting Styles: FY, FC
Bore Rod MM Bore MM
A B KK S SL VD Rod A B KK S SL VD
Ø Ø Ø Ø
32 B 25 34 M16×1.5 18 14 10 10 32 B 25 34 M16×1.5 18 14 10 10
A 35 43 M24×1.5 28 24 14 17 B 30 40 M20x1.5 22.4 19 11 10
40
40 B 30 40 M20x1.5 22.4 19 11 10 C 25 36 M16×1.5 18 14 10 10
B 35 46 M24×1.5 28 24 14 10
C 25 36 M16×1.5 18 14 10 10 50
C 30 40 M20x1.5 22.4 19 11 10
A 45 50 M30x1.5 35.5 30 16 17
B 45 55 M30x1.5 35.5 30 16 10
50 B 35 46 M24×1.5 28 24 14 10 63
C 35 46 M24×1.5 28 24 14 10
C 30 40 M20x1.5 22.4 19 11 10 B 60 65 M39×1.5 45 41 20 10
80
A 60 65 M39×1.5 45 41 20 19 C 45 55 M30x1.5 35.5 30 16 9
40 A 35 43 M24×1.5 28 24 14 10 A 75 80 M48×1.5 56 50 23 20
80 B 60 65 M39×1.5 45 41 20 10
50 A 45 50 M30x1.5 35.5 30 16 10
C 45 55 M30x1.5 35.5 30 16 9
63 A 60 65 M39×1.5 45 41 20 10 A 95 95 M64x2 71 65 27 23
100 B 75 80 M48×1.5 56 50 23 10
80 A 75 80 M48×1.5 56 50 23 8
C 60 65 M39×1.5 45 41 20 10
A 120 115 M80×2 90 85 33 17
100 A 95 95 M64x2 71 65 27 11
125 B 95 95 M64x2 71 65 27 10
125 A 120 115 M80×2 90 85 33 10 C 75 80 M48×1.5 56 50 23 10
5 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Rod End Shape 14 MPa Double Acting Hydraulic Cylinder
View
Table of Change of Rod End Shape
Contents
You can specify the shape and dimension of the rod end as shown below using the semi-standard symbols
and dimension symbols. (No need to specify the dimension symbol if you order a cylinder with the basic
dimension. Specify only the semi-standard symbol.)
How to order Series Model Number - x Semi-standard symbol
Special rod end shape type (Rod B) Special rod end shape type (Rod C)
A54 A54
6 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Rod End Shape 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents Special rod end shape type (Rod A)
Basic dimensional table
A82
k k k k k k k k
Bore W
A1+0.5
+0.3
A2 -0.2
-0.3
DM DP-0.2
-0.3
DR MM N V
MM is rod dia.
Note: Other rod end shapes - A00, A51, A53, A55 and A81 are
available. Please consult the manufacturer for these options.
7 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Rod End Shape 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents Separate Flange Joint (M-end): Only for piston rod end shape A82
F
4-D3 G
45° Reverse face
Spot facing dia. D4
depth H
D1 D2
A
C C
J
B B
3 E
8 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Drill hole for rod dia.
VD of φ100 or more Rod dia. OF DF
2-DF
Doublerod
Double rodtype
type(Ø32
(φ32to to φ250/rod
Ø125/rod B or
B or C) C)
forloading
for loadingon
onboth
bothsides
sides
MM ZM+stroke×2
A
ZK+stroke
W+
A Y PJ+stroke FP stroke A
KK Cushion valves
2-EE
D B F G H+stroke J
HL+stroke BB
MM MM
KK KK
C Ø32 to Ø100 : Max. 7
φ32 to φ100:Max. 7
TG Ø125to: φ150:Max.
Max. 11 11 W LZ+stroke
φ125
E φ160 to φ250:Max. 13
● The Switch Set (φ32 to φ140) is also within the
standard stroke range.
Bore W Y ZJ
Ø BB DD E EE F FP G H HL J LZ PJ PL TG ZK ZM
B-C A B-C A B-C A
32 11 M10×1.25 58 Rc3/8 11 38 50 44 141 36 166 90 13 38 30 – 68 – 171 – 196 226
40 11 M10×1.25 65 Rc3/8 11 38 50 44 141 36 166 90 13 45 30 35 68 73 171 176 196 226
50 11 M10×1.25 76 Rc1/2 13 42 54 48 155 40 182 98 15 52 30 41 72 83 185 196 212 242
63 13 M12×1.5 90 Rc1/2 15 46 56 52 163 40 194 102 15 63 35 48 81 94 198 211 229 264
80 16 M16×1.5 110 Rc3/4 18 56 66 54 184 46 222 110 18 80 35 51 91 107 219 235 257 292
100 18 M18×1.5 135 Rc3/4 20 58 66 60 192 46 232 116 18 102 40 57 98 115 232 249 272 312
125 21 M22×1.5 165 Rc1 24 67 76 64 220 56 264 130 23 122 45 57 112 124 265 277 309 354
• When using the SD style, be sure to see Cylinder Safety Guide at the end of this catalog.
• For the thread length (dimension A) in case of using the lock nut, refer to “Accessories.”
• For the mounting of sensors, refer to the dimensional drawing of “Switch Set.” All the contents other than “Sensor mounting dimensions”
are the same.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
9 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
VD 2-DF
70/140H-8 General Hy
f112 f111.5 f15
Catalog HY08-T1151-1/NA B S OF
Ⓓ Ⓐ
FE R B MM
KK
Ⓒ Cushion valves
TF VD FY LL+stroke
UF W LY+stroke BB
・For
● dimensions not shown in these figures, refer to the SD style (basic style).
Bore Ø BB E EE FB FE FY LL LY PJ R TF UF WF WY YP
125 21 165 Rc1 26 175 41 196 237 130 130 224 272 57 98 43
10 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
FY (for rods B & C) Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View φ32 to φ100:Max.7
φ125 to φ150:Max.11
Table of E φ160 to φ250:Max.13 Ø32
φ32to Ø100
A toSLφ100:: Max.
Max.
YP77 PJ+stroke
Contents φ125 to
Ø125 Max. 11Max.11
: φ150:
A 4-FB φ160 to φ250:Max.13 2-EE YP
E A SL PJ+stroke
A 4-FB 2-EE
D B
FE R B MM
D B
FE R B MM
KK
C KK Cushion valves
TF C VD FY LL+stroke Cushion valves
UF TF W FY
VD LY+ stroke BB
LL+stroke
UF W LY+stroke BB
Doublerod
Double rodtype
type(Ø32
(φ32to to φ250/rod
Ø125/rod B orBC)
or C)
for loading
for loadingon
onboth
both sidesrod type (φ32 to φ250/rod B or C)
Double
sides
W+
A W
for loading on both sides
LX+stroke stroke A
W+
YP PJ+stroke
A W LX+stroke stroke A
YP PJ+stroke
MM MM
MM MM
KK KK
VD FY KK KK
VD FY
Bore BB E EE FB FE FY LL LX LY PJ R TF UF W YP
Ø
32 11 58 Rc3/8 11 62 13 130 168 143 90 40 88 109 30 27
40 11 65 Rc3/8 11 69 13 130 168 143 90 46 95 118 30 27
50 11 76 Rc1/2 14 85 18 142 187 160 98 58 115 145 30 29
63 13 90 Rc1/2 18 98 20 148 199 168 102 65 132 165 35 31
80 16 110 Rc3/4 18 118 24 166 228 190 110 87 155 190 35 38
100 18 135 Rc3/4 22 150 28 172 240 200 116 109 190 230 40 38
125 21 165 Rc1 26 175 33 196 273 229 130 130 224 272 45 43
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of "Switch Set." All the contents other than "Sensor mounting dimensions"
are the same.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
11 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
LA Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of • Bore Ø32 to Ø125 ZB+stroke
Contents ZB+stroke A W FP PJ+stroke E : Max. 7
Ø32 to Ø100
SL 2-EE Ø125 : Max. 11
A W FP PJ+stroke E A
SL 2-EE EH
A
MM D B
LH
KK ST
Cushion EH
MM SY SU valves
D SU SY B C
4-SB
XS SS+stroke LH
TS
KK XB+stroke ST US
Cushion C
SY SU valves SU SY
4-SB
XS SS+stroke TS Double rod type (Ø32 to Ø125/rod B or C)
for loading on both sides
XB+stroke US
W+
A W FP PJ+stroke FP stroke A
MM MM
KK W+ KK
A W FP PJ+stroke FP stroke A
XS SV+stroke XS+stroke
Bore W XB XS ZB MM
E EE EH P LH PJ SB SS ST SU SV MM
SW SX SY TS US
Ø B-C A B-C A B-C A B-C A
KK KK
32 58 Rc3/8 64 38 35±0.15 90 11 98 12 31 112 – – 13 88 109 30 – 155 – 57 – 182 -
40 65 Rc3/8 70 38 37.5±0.15 90 11 98 14 31 112 – – 13 XS
95 118 30SV+stroke
35 155 160 57XS+stroke
62 182 187
50 76 Rc1/2 83 42 45±0.15 98 14 108 17 34 122 – – 14 115 145 30 41 168 179 60 71 196 207
63 90 Rc1/2 95 46 50±0.15 102 18 106 19 32 122 – – 18 132 165 35 48 177 190 71 84 211 224
80 110 Rc3/4 115 56 60±0.25 110 18 124 25 42 144 – – 18 155 190 35 51 198 214 74 90 235 251
100 135 Rc3/4 138.5 58 71±0.25 116 22 122 27 38 142 – – 22 190 230 40 57 207 224 85 102 250 267
125 165 Rc1 167.5 67 85±0.25 130 26 136 32 41 156 – – 25 224 272 45 57 235 247 99 111 286 298
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions”
are the same.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
12 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
f32 25 f34 M16×1.5
f32 25 f34 M16×1.5 f18 14 10 1
f40 30 f40 M20×1.5
f40 30 f40 M20×1.5 f22.4 19 11 1
f50 35 f46 M24×1.5
Catalog HY08-T1151-1/NA f50 35 f46 M24×1.5 f28 24 14 1
f63 45 f55 M30×1.5
TA Mounting Style 14 MPa Double Acting Hydraulic Cylinder
f63 45 f55 M30×1.5 f35.5 30 16 1
f80 60 f65 M39×1.5
f80 60 f65 M39×1.5 f45 41 20 1
f100 75 f80 M48×1.5
View f100 75 f80 M48×1.5 f56 50 23 1
A W FM PJ+stroke f125 95 f95 M64×2
Table of A W FM PJ+stroke f125 95 f95 M64×2 f71 65 27 1
SL 2-EE
Contents Ⓐ SL 2-EE f140 110 f105 M72×2
f140 110 f105 M72×2 f80 75 31 1
Ⓐ
JR f150 115 f110 M76×2
JR f150 115 f110 M76×2 f85 80 33 1
f160 120 f115 M80×2
f160 120 f115 M80×2 f90 85 33 1
Ⓓ Ⓑ TD E MM f180 140 f125 M95×2
Ⓓ Ⓑ TD E MM f180 140 f125 M95×2 f100 ― Drill 1
hole
f200 150 f140 M100×2
KK f200 150 f140 M100×2 f112 ― Drill
hole
1
KK f224 180 f150 M120×2
Ⓒ Cushion valves f224 180 f150 M120×2 f125 ― Drill
hole 1
Ⓒ Cushion valves
TL TC TL HL+stroke BB f250 195 f170 M130×2
TL TC TL
φ32totoØ100
Ø32
φ32 to φ80 :Max.Ø125
7
φ80 :: Max.
Max.77
HL+stroke BB f250 195 f170 M130×2 f140 ― Drill
hole 1
φ100 to φ150:
: Max. 11Max.11 XG
UT
φ100 to φ150:Max.φ160
11
UT XG Max.13
to φ250:
φ160 to φ250:Max.13 ZJ+stroke
Symbol
ZJ+stroke
Symbol BB E EE
BB E EE
Bore FM FP HL
● For dimensions not shown in these figures, Double rod type (rod B or C) Bore
● For dimensions not shown in these figures,
refer to the SD style (basic style). Double rod type (rod B or C)
for loading on both sides f32 11 □58
f32 11 □58 Rc3/8
Rc3/8 38 38 141
refer to the SD●style (basic style).
For the mounting of sensors, refer tofor theloading on both sides LZ+stroke f40 11 □65 Rc3/8
● For the mounting of sensors, refer to the f40 11 □65 Rc3/8 38 38 141
LZ+stroke W+
dimensional drawings of“Switch Set.” All W+
dimensional drawings of“Switch Set.” All A W FM PJ+stroke FP stroke A f50 11 □76 Rc1/2
the contents other than“Sensor mountingA W FM PJ+stroke FP stroke A f50 11 □76 Rc1/2 42 42 155
the contents other than“Sensor mounting
dimensions”are the same. f63 13 □90 Rc1/2
dimensions”are the same. f63 13 □90 Rc1/2 46 46 163
● The cushion valve and air vent of the TA
● The cushion valve and air vent of the TA f80 16 □110 Rc3/4
style are positioned on Ⓒ for structural f80 16 □110 Rc3/4 56 56 184
style are positioned on Ⓒ for structural MM f100 18 □135 Rc3/4
reasons (rod cover side). MM
MM
f100 18 □135 Rc3/4 58 58 192
reasons (rod cover side).
● If the port size exceeds 1 inch, it is
MM
● If the port size exceeds 1 inch, it is KK f125 21 □165 Rc1
recommended to order G thread or KKpipe
KK f125 21 □165 Rc1 67 67 220
KK
recommended to order G thread or pipe f140 22 □185 Rc1
flange. In such a case, contact us. f140 22 □185 Rc1 69 69 230
flange. In such a case, contact us. ● The Switch Set (φ32 to φ140) is also within the standard stroke
(Order made) ● The Switch Set (φ32 to φ140) is also within the standard stroke
f150 25 □196 Rc1
(Order made) range. f150 25 □196 Rc1 71 71 240
range. W XG ZJ f160 25 74□210 Rc1
Bore Ø BB E EE FM FP HL JR LZ PJ TC TD Ø TL UT f160 25 □210 Rc1 74 253
B-C A A
B-C f180 B-C f180 27 □235 Rc1 1/
A
27 □235 Rc1 1/4 106 75 306
0 f200 29 □262 Rc1 1/
32 11 58 Rc3/8 38 38 141 R2 166 90 58 —0.3 20e9 20 98 30 – 62 –
f200 29171□262 –
Rc1 1/2 116 85 332
f224 34 □292 Rc1 1/
0 f224 34 □292 Rc1 1/2 129 89 345
40 11 65 Rc3/8 38 38 141 R2 166 90 69 —0.3 20e9 20 109 30 35 62 67 171 176 f250 37 □325 Rc2
f250 37 □325 Rc2 126 106 366
● The tolerance of B is
0 With Boots
63 13 90 Rc1/2 46 46 163 R2.5 194 102 98 —0.35 31.5e9 31.5 161 35 48 74 With
87 Boots
198 211
Symbol
Symbol f32
0 f32 f40 f50 f
80 16 110 Rc3/4 56 56 184 R2.5 222 110 118 —0.35 31.5e9 31.5 181 35 51 82 98 219 235
Bore
Bore
Rod B 40
0 Rod B 40 50 63 7
100 18 135 Rc3/4 58 58 192 R3 232 116 145 —0.4 40e9 40 225 40 57 89 106 232 249
WW Rod C ―
WW Rod C ― 50 50 6
0 Rod A ―
125 21 165 Rc1 67 67 220 R3 264 130 175 —0.4 50e9 50 275 45 57 103 115 265A
Rod 277
― 63 71 8
Rod B 45
• For dimensions not shown in the figures above, refer to the SD style (basic style). Rod B 45 45 45 5
X Rod C ―
X Rod C ― 45 45 5
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions” Rod A ―
are the same. Rod A ― 45 55 5
• The cushion valve and air vent of the TA style are positioned on C for structural reasons (rod cover side).
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
13 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
TC Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of φ32 to φ100:Max.7 Ø32 to Ø100
φ32 : Max.
to φ100:
AØ125 W: Max.F11 P
Max.7 7
A W PJ+stroke
FP PJ+stroke
φ125 to φ150:Max.11 φ125 to φ150:Max.11
Contents E φ160 to φ250:Max.13
E SL φ160 to φ250:Max.13 2-EE
SL BD 2-EE BD
Ⓐ JR Ⓐ JR
Ⓓ Ⓑ Ⓓ
TD MM Ⓑ TD MM
KK KK
Ⓒ Ⓒ Cushion valves Cushion valves
TL TM TL TL TM TL HL+stroke HL+stroke
UM UM XV+1/2 stroke=PH XV+1/2 stroke=PH BB BB
ZJ+stroke ZJ+stroke
Double
Double rod (Ø32
rod type type (φ32 to φ250/rod
Double
to Ø125/rod rodB type B or C)to φ250/rod B or C)
or C) (φ32
for loading
for loading on sides
on both both sides
for loading on both sides
LZ+stroke LZ+stroke
W+ W+
A W FP PJ+stroke
A W FP FP stroke
PJ+strokeA FP stroke A
MM MM MM MM
KK KK KK KK
Bore Min. PH TD W XV ZJ
BB BD E EE FP HL JR LZ PJ TL TM UM
Ø B•C A Ø B-C A B-C A B-C A
0
32 11 28 58 Rc3/8 38 141 R2 166 105 – 90 20e9 20 58 —0.3 98 30 – 113 – 171 –
0
40 11 28 65 Rc3/8 38 141 R2 166 105 110 90 20e9 20 69 —0.3 109 30 35 113 118 171 176
0
50 11 33 76 Rc1/2 42 155 R2.5 182 113.5 124.5 98 25e9 25 85 —0.35 135 30 41 121 132 185 196
0
63 13 43 90 Rc1/2 46 163 R2.5 194 127.5 140.5 102 31.5e9 31.5 98 —0.35 161 35 48 132 145 198 211
0
80 16 43 110 Rc3/4 56 184 R2.5 222 140.5 156.5 110 31.5e9 31.5 118 —0.35 181 35 51 146 162 219 235
0
100 18 53 135 Rc3/4 58 192 R3 232 152.5 169.5 116 40e9 40 145 —0.40 225 40 57 156 173 232 249
0
125 21 58 165 Rc1 67 220 R3 264 174 186 130 50e9 50 175 —0.40 275 45 57 177 189 265 277
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions”
and “Minimum dimension PH of Switch Set Cylinders” are the same.
• To change the position of TC accessory, specify dimension PH.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
14 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
FK Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of Ø32
φ32 to φ100:Max.7
Ø100 : Max. 7
Ø125 : φ150:Max.11
φ125 to Max. 11
Contents E φ160:Max.13 A W FP PJ+stroke
4-FB SL 2-EE NF
A
FE R D B MM
KK
C
TF Cushion valves
UF HL+stroke
XY+1/2 stroke=PN
ZJ+stroke BB
・For dimensions not shown in these figures, refer to the SD style (basic style).
・For the mounting of sensors, refer to the dimensional drawings of“Switch Set.”
All the contents other than“Sensor mounting dimensions”and“Minimum
dimension PN of Switch Set Cylinders” are the same.
Bore Ø Min. PN W XY ZJ
BB E EE FB Ø FE FP HL NF PJ R TF UF
B-C A B-C A B-C A B-C A
15 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
CS Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of φ40 to φ100 :Max.7
φ125 :Max.11 E
Contents
A W FP PJ+stroke Grease nipple
Max.HG
SL 2-EE EL
CD
3°
MM
3°
KK MR
Cushion valves L EM
HL+stroke EN
FL
XD+stroke
ZC+stroke
● The spherical bearings are not filled with grease. Lubricate appropriately through the grease nipple.
● The bearing inner diameter and mounting width conform to JIS B8367-2 MP5 type regulation. (Same
standard with 160H-1 Series)
● For dimensions not shown in these figures, refer to the SD style (basic style).
● For the mounting of sensors, refer to the dimensional drawings of“Switch Set.” All the contents
16 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
CB Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View Bore φ32φ32
to φ80
● Bore φ32 to φ80
● ● Bore to φ80 ● Bore φ32 to φ80
Table of A WA FP
W FP
PJ+stroke
PJ+stroke L L A W FP With pin With pin PJ+stroke
A
L
W FP PJ+stroke
With pin
L
SL 2-EE CD
Contents SL SL 2-EE 2-EE CD CD SL 2-EE CD
Ⓐ Ⓐ Ⓐ
MM
MM MM MM Ⓑ Ⓑ Ⓓ Ⓓ Ⓑ Ⓓ
MR
MR MR KK MR
KK KK KK
Cushion valves
Cushion Cushion
valves valves Ⓒ Ⓒ Cushion valves Ⓒ
HL+stroke FL
HL+stroke FL FL CB CB HL+stroke FL CB
HL+stroke XD+stroke
XD+stroke
XD+stroke UB XD+stroke UB
UB ZC+stroke
ZC+stroke Max.7 ZC+stroke
ZC+stroke Max.7 E E Max.7 E
MM
MM MM MM Ⓑ Ⓑ Ⓓ Ⓓ Ⓑ Ⓓ
KK
KK KK KK
Cushion valves
Cushion Cushion
valves valves Cushion valves
Ⓒ Ⓒ HL+stroke Ⓒ FL
HL+stroke
HL+stroke FL FL CB CB HL+stroke FL CB φ100
φ100 :Max.7 φ100 :Max.7 XD+stroke
XD+stroke φ100 :Max.7 UB XD+stroke UB φ12
XD+stroke φ12 :Max.11 UB φ12 :Max.11 ZC+stroke
φ12 :Max.11
ZC+stroke
ZC+stroke E ZC+stroke E
E
● For dimensions not shown in these figures, refer to the SD style ● Material of CB accessory for cylinde
● For dimensions not shown
● For dimensions notinshown
theseinfigures, refer to refer
these figures, the SDto style ● Material
the SD style of CB accessory
● Material Forcylinders
● for
of CB accessory dimensionswithnot
for cylinders shown
bores
withfromin32
these
bores to 1figures,
from to 1refer
32 mm:
25 to the
Nodular
25 mm: SD style
graphite
Nodular cast ironcast
graphite ● Material of CB accessory for cylinders with bores from 32 to 125 mm: Nodular graphite cast iron
iron style).
(basic ● If the port size exceeds 1 inch, it is r
(basic style).
(basic style). +0.4 ● If the ●port
If size
the exceeds
port size 1 (basicit1style).
inch,
exceeds is recommended
inch, it is to
recommendedorder G
to thread
order Gor pipe
thread flange.
or pipe In such
flange. a
In such W
● Ifa the port size exceeds 1 inch, it is XD
recommended to order G ZC
thread or pipe flange. In such a
H9 ● For the mounting of sensors, refer to the dimensional drawings of
Bore
● For the Ø ofCB
● mounting sensors,
For the mounting +0.1refer to CD
of sensors, the dimensional
refer
E drawings
drawings
tof8the dimensional of EE
ofcase, contact
FL ●made)
us. (Order
FPmounting ofHL
For the sensors, refer toLthe dimensional
MR drawings PJ of UB
case, contact us. (Order made)
case, contact us. (Order made)
case, contact us. (Order made) “Switch Set.” B-C A
All the contents other B-C A
than“Sensor mountingB-C A
“Switch“Switch
Set.” AllSet.”
the contents other than
All the contents “Sensor
other mountingmounting
than“Sensor “Switch Set.” All the contents other than“Sensor mounting
32 25 16 58 Rc3/8 38 38 141 R20 R16 90 50 30 – 209 – 225 –
50 31.5 20 76 Rc1/2 45 42 155 R25 R20 98 63.5 30 41 230 241 250 261
63 40 31.5 90 Rc1/2 63 46 163 R40 R31.5 102 80 35 48 261 274 292.5 305.5
80 40 31.5 110 Rc3/4 72 56 184 R40 R31.5 110 80 35 51 291 307 322.5 338.5
100 50 40 135 Rc3/4 84 58 192 R50 R40 116 98 40 57 316 333 356 373
125 63 50 165 Rc1 100 67 220 R62 R50 130 126 45 57 365 377 415 427
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions”
are the same.
• Material of CB accessory for cylidners with bores from 32 to 125 mm: Nodular graphite cast iron.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
17 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
FZ Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of Ø32
φ32to
toØ100
φ100:: Max.
Max.7 7
φ32 to φ100:Max.7
Contents φ125 to φ150:Max.11
φ125
Ø125 to: φ150:
Max. 11Max.11
A W FP PJ+stroke φ160 to φ250:Max.13 E 4-FB
A W FP PJ+stroke φ160 to φ250:Max.13 E 4-FB
SL 2-EE A
SL 2-EE A
B D
MM B D R FE
MM R FE
KK
KK
Cushion valves
Cushion valves C
C
HL+stroke FY TF
HL+stroke FY TF
ZY+stroke UF
ZY+stroke UF
W ZY
Bore Ø E EE FB FE FP FR FY HL LX PJ R TF UF
B-C A B-C A
32 58 Rc3/8 11 62 38 40 13 141 168 90 40 88 109 30 – 184 –
40 65 Rc3/8 11 69 38 40 13 141 168 90 46 95 118 30 35 184 189
50 76 Rc1/2 14 85 42 47 18 155 187 98 58 115 145 30 41 203 214
63 90 Rc1/2 18 98 46 51 20 163 199 102 65 132 165 35 48 218 231
80 110 Rc3/4 18 118 56 62 24 184 228 110 87 155 190 35 51 243 259
100 135 Rc3/4 22 150 58 66 28 192 240 116 109 190 230 40 57 260 277
125 165 Rc1 26 175 67 76 33 220 273 130 130 224 272 45 57 298 310
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions”
are the same.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
18 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
FC Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of Ø32
φ32totoØ100 : Max.
φ100: Max.7 7
φ32 to φ100:Max.7 Ø125 : Max. 11Max.11
φ125 to φ150:
φ125 to φ150:Max.11
Contents8-FB E
8-FB
φ160 to φ250: Max.13 E φ160 to φ250:Max.13
A SL YP
A SL
PJ+stroke
YP PJ+stroke
2-EE
A 2-EE
A
D B
D B R TF UF B MM
R TF UF B MM
KK
KK Cushion valves
C Cushion valves
C
R VD F LL+stroke
R VD F LL+stroke
TF W HL+stroke BB
TF W HL+stroke BB
UF
UF
● The Switch Set (φ32 to φ140) is also within the standard stroke range.
● The Switch Set (φ32 to φ140) is also within the standard stroke range.
Bore Ø BB E EE F FB HL LL LZ PJ R TF UF W YP
19 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
FD Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of Ø32 to Ø100 : Max. 7
φ32 to φ100:Max.7
Contents Ø125
φ125 :toMax.
φ150:11Max.11
φ32 to φ100:Max.7
A W FP PJ+stroke
φ125 to φ150:Max.11 φ160 to φ250:Max.13 E
8-FB
A W FP PJ+stroke φ160 to φ250:Max.13 E
8-FB
SL 2-EE A
SL 2-EE A
B D
MM R TF UF
B D
MM R TF UF
KK
KK
Cushion valves C
Cushion valves C
HL+stroke F R
HL+stroke R TF
ZH+Fstroke
TF UF
ZH+stroke
UF
For dimensions not shown in these figures,
● Double rod type (φ32 to φ250/rod B or C)
Double rod type (Ø32 to Ø125/rod
style (basic style). Double rod type (φ32
B orBC)or C)
● For dimensions not shown referin to
these figures,
the SD forto φ250/rod
loading on both sides
refer to the SD style (basic style).
● For the mounting of sensors, refer to
for
forloading
the
on both sides
loading on both sides LZ+stroke
● For the mounting of sensors,
W+
refer todrawings
dimensional the of“Switch Set.” All LZ+stroke A W FP
W+ PJ+stroke YP F stroke A
dimensional drawings ofthe
“Switch Set.”
contents All than“Sensor mounting
other A W FP PJ+stroke YP F stroke A
the contents other than“Sensor
dimensions” mounting
are the same.
dimensions”are the same.
● If the port size exceeds 1 inch, it is
● If the port size exceeds recommended
1 inch, it is to order G thread or pipe
MM MM
recommended to order G threadInorsuch
flange. pipe a case, contact us.
MM MM
flange. In such a case, (Order
contact us.
made) KK KK
(Order made) KK KK
● The Switch Set (φ32 to φ140) is also within the standard stroke range.
● The Switch Set (φ32 to φ140) is also within the standard stroke range.
W ZH
Bore Ø E EE F FB FP HL FP PJ R TF UF YP
B-C A B-C A
32 58 Rc3/8 11 11 38 141 166 90 40 88 109 30 ― 27 182 ―
40 65 Rc3/8 11 11 38 141 166 90 46 95 118 30 35 27 182 187
50 76 Rc1/2 13 14 42 155 182 98 58 115 145 30 41 29 198 209
63 90 Rc1/2 15 18 46 163 194 102 65 132 165 35 48 31 213 226
80 110 Rc3/4 18 18 56 184 222 110 87 155 190 35 51 38 237 253
100 135 Rc3/4 20 22 58 192 232 116 109 190 230 40 57 38 252 269
125 165 Rc1 24 26 67 220 264 130 130 224 272 45 57 43 289 301
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions”
are the same.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
• The Switch Set (Ø32 to Ø125) is also within the standard stroke range.
20 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
CA Mounting Style 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents Ø32 to toØ100
φ32 : Max.
φ100: Max.7 7
Ø125
φ125 :toMax. 11Max.11
φ150:
A W FP PJ+stroke φ160 to φ250:Max.13 E
SL 2-EE Ⓐ
L
CD
MM Ⓑ Ⓓ
MR
KK
Cushion valves Ⓒ
HL+stroke FL EW
XD+stroke
ZC+stroke
● For dimensions not shown in these figures, refer to the SD style (basic style).
● For the mounting of sensors, refer to the dimensional drawings of“Switch Set.” All the contents other than
“Sensor mounting dimensions” are the same. W XD ZC
Bore Ø CD E the cylinders
● For EE with a boreEWof+0.4
180 mmFL
+0.1 FPthe CA
or more, HLaccessory
L is provided
MR PJ a gray cast iron bush.
with
B-C
● The CA accessory for cylinders with a bore of 180 mm or more is made of rolled steel for A B-C
general structure A B-C A
(welding type) and provided with a gray cast iron bush.
32 16H9 ● 58 Rc3/8
If the port size exceeds 1 25 38
inch, it is recommended38 to order
141 G thread
R20 or pipe
R16flange. 30a case,―contact
90In such 209 ― 225 ―
us. (Order made)
40 16H9 65 Rc3/8 25 38 38 141 R20 R16 90 30 35 209 214 225 230
50 20H9 76 Rc1/2 31.5 45 42 155 R25 R20 98 30 41 230 241 250 261
63 31.5H9 90 Rc1/2 40 63 46 163 R46 R31.5 102 35 48 261 274 292.5 305.5
80 31.5H9 110 Rc3/4 40 72 56 184 R52 R31.5 110 35 51 291 307 322.5 338.5
100 40H9 135 Rc3/4 50 84 58 192 R62 R40 116 40 57 316 333 356 373
125 50H9 165 Rc1 63 100 67 220 R73 R50 130 45 57 365 377 415 427
• For dimensions not shown in the figures above, refer to the SD style (basic style).
• For the mounting of sensors, refer to the dimensional drawings of “Switch Set.” All the contents other than “Sensor mounting dimensions”
are the same.
• If the port size exceeds 1 inch, it is recommended to order G thread or pipe flange. In such a case, contact us. (Order made)
21 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Accessories 14 MPa Double Acting Hydraulic Cylinder
View
Table of Rod eye (T-end) Rod eye with spherical bearing (S-end)
Contents
φ40 to φ63 φ80 to φ125
φ32 to φ160
Ø32 to Ø125 φ180 to φ250
Ø40 to Ø63 Ø80 to Ø125
CD AV CD AV
CK AV CK AV
EN EM EF EN EM EF
EM EM EF
3°3° 3°3°
RA RA
EL Grease nipple EL Grease nipple
ER RA ER RA ER
CF
J Hex. screw KK KK
Hex. screw
ER
J Max. HG Max. HG
45° 45°
KK
ED
ED KK ED EG ED
LE
LE
CR CE CR CE
Hex. screw Hex. screw
LE LE
CE CE
Notes)
● The spherical bearings are not filled with grease. Lubricate appropriately through the grease nipple.
Rod eye (T-end) ● The bearing inner diameter and mounting width conform to JIS B8369.
Grease nipple
Rod B Rod C Rod B Rod C
Bore Bore
Ø Ø
Grease nipple type EL HG Grease nipple type EL HG Grease nipple type EL HG Grease nipple type EL HG
40 JIS A type MT6×1 11 11 JIS A type MT6×1 11 11 80 JIS A type Rc1/8 20 15 JIS A type Rc1/8 20 15
50 JIS A type MT6×1 14 11 JIS A type MT6×1 14 11 100 JIS A type Rc1/8 24 15 JIS A type Rc1/8 24 15
63 JIS A type Rc1/8 15 15 JIS A type Rc1/8 15 15 125 JIS A type Rc1/8 28 15 JIS A type Rc1/8 28 15
22 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
152 70/140H-8 7/14 MPa Double Acting Hydraulic Cylinder
Double Acting Single Rod/Double Rod Unit: mm
Catalog HY08-T1151-1/NA
Accessories 14 MPa Double Acting Hydraulic Cylinder
View Rod clevis (Y-end) with pin
Table of 70/140H-8 General Hydraulic Cylinders
Contents
Rod clevis (Y-end) with pin
φ32 to φ80 φ100 Ø125 to φ250
φ125
CK CK CK AV
CW CW CW
Hex. screw
BL CL CM YD BL CL CM YD BL CL CM
CW
CW CW
Retainer
Retainer Retainer CV
CV CV Hex. head bolt
Hex. socket head cap screw Hex. head bolt
RA RA RA
ER ER
LE KK LE KK LE
CE Hex. screw CE Hex. screw CR CE
125 RYH-64-H RYH-48-1-H 97 77 143 180 50 126 63 50 12 31.5 100 R54 30 M64×2 M48×1.5 70 230 – –
23 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
d
Catalog HY08-T1151-1/NA
Accessories 14 MPa Double Acting Hydraulic
C
Cylinder
View
Table of
Contents
Lock nut H B
Bore Dimension
Rod Part number B C d H d
Ø A
32 B LNH-16F-H 22 25.4 M16×1.5 10 40The standard fitting length of the rod end attachment and
C If the
piston rod is about 80% of the thread diameter.
A LNH-24F-H 32 37.0 M24×1.5 14 50
fitting length is insufficient due to the use of the lock nut,
40 B LNH-20F-H 27 31.2 M20x1.5 12 it is necessary to increase the thread length (dimension A)
45
as shown below.
C LNH-16F-H 22 25.4 M16×1.5 10 40 H B
C LNH-20F-H 27 31.2 M20x1.5 12 45 The standard fitting length of the rod end attachment and
/140H-8 63
A
B
7/14 MPa Double
LNH-39F-H
Double
LNH-30F-H
55
Acting
63.5Acting
41 Single
47.3
M39×1.5Hydraulic
20
Rod/Double
M30x1.5 17 Rod
60
Cylinder
80 piston rod is about 80% of the thread diameter. If the
fitting length is insufficient due to the use of the lock nut,
it is necessaryUnit:
7/14 MPa Dou
mm the thread length (dimension A) Unit: mm
to increase
as shown below.
Double A
C LNH-24F-H 32 37.0 M24×1.5 14 50
A LNH-48F-H 70 80.8 M48×1.5 26 95
A end
Rod
80 B LNH-39F-H 55 63.5 M39×1.5 20 80 attachment Lock Nut
el Pin The standard fitting length of the rod end Dimensional
attachment and Table/Pa
0/140H-8
C LNH-30F-H 41 47.3 M30x1.5 17 60
A
7/14 MPa
LNH-64F-H
Double
90 104
Acting
M64x2
Hydraulic
35 125
Cylinder
piston rod is about 80% of the thread diameter. If the7/14 MPa D
fitting length is insufficent due to the use of Symbol
the lock nut, it
100 B
Double
LNH-48F-H
Acting
70
Single
80.8
Rod/Double
M48×1.5 26 95
Rod isUnit: mm to increase the thread length (dimension
necessary Unit: mm
Bore
BL
A) Double
C
as shown above.
C LNH-39F-H 55 63.5 M39×1.5 20 80 f32 62 4
A LNH-80F-H 110 127 M80×2 43 155 f40 62 4
125 B LNH-64F-H C 90 D
104 M64x2 35 125 A
E f50
allel Pin Dimensional
76.5
Table/P
5
C LNH-48F-H 70 80.8 M48×1.5 26 95
f63Symbol 93 5
CK
f80 93 BL 5C
Bore
f100 117 7
f32 62
Parallel Pin
BL f125 143 7
f40 62
Bore Ø BL C CK D E
C D f140 183 10
E f50 76.5
32 62 4 16 3 3
f150 183 10
f63 93
CK
40 62 4 16 3 3
f160 183 10
50 76.5 5 20 3 3 f80 93
● The tolerance of CK is f8.
f32 25 14
2-L Bore F G H I J K L Retainer mounting
Ø Ø bolt size f40 25 14
f50
tainer 32 25 14 7 7 14 3 6.5 M6 Dimensional Table/R
32 18
H f63Symbol 32 18
J
40 25 14 7 7 14 3 6.5 M6
I 50 32 18 7.5 7.5 15 4.5 7 M6 f80 32 F 18 G
Bore
63 32 18 7.5 7.5 15 4.5 7 M6 f100 50 30
f32 25 14
G
2-L K 80 32 18 7.5 7.5 15 4.5 7 M6 f125 65 40
F
f40 25 14
100 50 30 10 10 20 6 10 M8 f140 75 48
f50 32 18
H 125 65 40 12 10 22 6 12 M10 f150 75 48
f63 32 18
J f160 75 48
I f80 32 18
f100 50 30
G
K f125 65 40
F 24 Taiyo America
St. Marys, Ohio f140 75 48
www.taiyoamericacylinders.com USA
f150 75 48
f160 75 48
Catalog HY08-T1151-1/NA
Seal Kits 14 MPa Double Acting Hydraulic Cylinder
View
Table of Standard and Semi-standard type 140H-8
Contents for Double acting single rod cylinders
25 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Theoretical Push and Pull Forces 14 MPa Double Acting Hydraulic Cylinder
View
Table of The bore of a hydraulic cylinder depends on the required A1 : push side piston pressurized area (mm 2) A1 = : D2
Contents
cylinder force.
A2 : pull side piston pressurized area (mm2) A2 = : (D 2 - d2)
• Push side cylinder D : cylinder bore (mm) d: piston rod dia. (mm)
force
A1 P : set pressure (MPa)
F1 = A1 X p X P (N)
- F2� �A2 ��
• Pull side cylinder � : load rate
force
! t F2 = A2 X p X P (N)
When deciding the actual cylinder output, the resistance in the
cylinder slipping part and the pressure loss in piping and machines
Supply
must be considered.
The load rate is the ratio of the actual force loaded onto the cylinder to
the theoretical force (theoretical cylinder force) calculated from the
circuit set pressure. The general set points are shown below.
For low speed working ..... 60 to 80%
The hydraulic cylinder theoretical output table is For high speed working ..... 25 to 35%
based on the calculation results of the formula above.
Pushed hydraulic cylinder theoretical output table (load rate 100%) Unit: kN (1kN = 102kgf)
Pulled hydraulic cylinder theoretical output table (load rate 100%) Unit: kN (1kN = 102kgf)
Switch Set
Indicating lamp
PH
PN
PH
● The・FK style
minimum dimensions PH and PN of a Switch Set Cylinder
are the dimensions obtained when the sensor is mounted on When boots are provided, dimension W
the rod side and the trunnion is moved toward the rod side changes. Specify dimension PH or PN.
as far as possible.
PN
27 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Switches 14 MPa Double Acting Hydraulic Cylinder
View
Table of Max. switching Protective Indicating Wiring Cord Applicable
Type Sensor Symbol Load voltage range Load current range
Contents capacity circuit Lamp method length load
AF AX101CE 1.5m
programmable controller
None
LED
AG AX105CE DC:5 to 30V DC:5 to 40mA 5m
Reed sensor
(Lights in
Small relay,
red when 0.3 MM2,
AC:5 to 120V AC:5 to 20mA DC: 1.5W 2-core, outer
AH AX111CE sensing) 1.5m
AC:2VA Provided dia. Ø 4mm
AJ AX115CE Rear wiring 5m
DC: 30V or less DC: 40mA or less
AE AX125CE None None 5m
AC: 120V or less AD: 20mA or less
Notes) ● For the sensors without a protective circuit, be sure to provide a protective circuit (SK-100) with the load when using any induction load (relay, etc.).
Notes) ● For the sensors without a protective circuit, be sure to provide a protective circuit (SK-100) with the load when using any induction load (relay, etc.).
● The output logic of AX is B contact. When the piston is detected, the sensor contact turns off (the lamp turns on).
● The output logic of AX is B contact. When the piston is detected, the sensor contact turns off (the lamp turns on).
● For the details of sensors, be sure to read the sensor specifications at the end of this catalog.
● For the details of sensors, be sure to read the sensor specifications .at the end of this catalog.
● We recommend AND Unit (AU series) for multiple sensors connected in series.
● We recommend AND Unit (AU series) for multiple sensors connected in series.
● For details, refer to AND Unit at the end of this catalog.
● For details, refer to AND Unit at the end of this catalog.
1. Loosen the two hex. screws with a hex. wrench, and move them
● Standard type Setting method of sensor detection position along the tie rod.
● Standard type
AX type AX type 1.
2.Loosen
Adjustthe
thetwo hex. screws
detecting with a (for
position hex. wrench, and type,
the 2-LED move the position where
AX type
(rear wiring) Fit the accessory into them along the
the green tie rod.
lamp lights up) 2 to 5 mm (about half of the operating
(rear wiring) the middle position of
the sensor. Fit from the
Fix to the bracket rangethe
2. Adjust is appropriate) before
detecting position the2-LED
(for the required position where the sen-
type, the
with the sensor
direction shown in the sor indicator lamp starts to ligh up (ON). Then, gently hold the top
mounting screw M4.
figure for easier fitting. position where the green lamp lights up) 2 to 5 mm (about
of the sensor so that the cylinder tube contacts the detecting face
half of the
of the operating
sensor, andrange is appropriate)
clamp before to
the hex. screw thean appropriate tighten-
Tie rod size (M6 to M10): Hex. screw M5 required position
ing torque. where
Note) the sensor indicator
Inappropriate lamp starts
tightening torqueto may cause the
[tightening torque: 1 to 2 N・m]
Tie rod size (M12 to M27): Hex. screw M6
light up (ON).off-center
off-center Then, gently
of hold
the the top ofposition.
sensor the sensor so
[tightening torque: 2 to 3 N・m]
Tie rod
3.that
Thethe cylinder tube
indicating lampcontacts thewhen
lights up detecting
theface of the
sensor is set to the ON
sensor, and clamp the hex. screw to an appropriate
position.
Hold with hands.
Sensor mounting screw M4
[tightening torque:
0.6 to 1 N・m]
4.tightening
Sensors torque.
can be mounted to any of four tie rods on the most suit-
Note)
able Inappropriate tighteningon
position depending torque may cause the
the mounting space of the cylinder and
Adjust until the sensor
comes in contact with off-center of the sensor position.
wiring method.
the cylinder tube.
3.
5.The indicating
Mount lamp lights
a sensor to theupmost
whensuitable
the sensor is set totothe
position detect the stroke
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ON
endposition.
with the "sensor mounting dimension" (dimension UX).
~~~~~~~~
(The lamp of SR405 goes out when sensor is turns on.)
Mounting style 4. Sensors can be mounted to any of
Styles other than TC TCfour tie rods and on the
style
Sensor quantity With one sensor With two most suitable With
sensors position depending
one sensoron theWith
mounting
two space
sensors
Bore of the cylinder and wiring method.
Ø mm Sensor type AX type AX type AX type AX type
5. Mount a sensor to the most suitable position to detect the
32 20 25stroke end with the“sensor
50 mounting dimension”
110
40 20 25(dimension UX). 50 115
50 20 25 50 115
63 20 25 60 125
80 20 25 60 130
100 20 25 65 135
125 20 25 70 150
28 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Ports and Cushions 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents
Cushion valve and air vent positions depending Port, cushion and air vent positions for LA style
on cylinder bore (for rod A only)
Port position Ⓐ Port position Ⓑ
Bore f40, f50, f100, f140, f150 A A
D B D B
D B D B
C C
D B
C Cushion To change the port and cushion valve positions from the
valves Example cap side to the rod side (AB on rod side, BC on cap side)
140H-8 2LA80BB100-AB-X PPC PC-BC
29 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Ports and Cushions 14 MPa Double Acting Hydraulic Cylinder
View
Table of Port G (ISO 1179-1) or NPT Thread Dimension Table Unit: mm
Contents (order made) G thread
Bore NPT thread
For a port G thread type cylinder, make an order AE DE FF
in accordance with the following procedure. f32 12 f25.5 G3/8 NPT3/8
(Example) 140H-8 2LA50BB100-G A B f40 12 f25.5 G3/8 NPT3/8
G: Port G thread type N: NPT thread type f50 14 f30 G1/2 NPT1/2
Port position f63 14 f30 G1/2 NPT1/2
AE
■G thread type/NPT thread type The thread type can be specified by the cylinder model number
(φ32 toφ125) (only standard port size) without using the semi-standard symbol and specification symbols.
Example)140H-8 2LA50BB100- G A B -TL
G:Port G thread type N:NPT thread type
For the G thread port size, refer to Port position
the dimensional table in the model
specification field. Cushion valve position
30 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Weight Table/General purpose type and cutting oil proof type Unit: kg
Basic weight
Catalog HY08-T1151-1/NA Additional weight
Mounting accessory weight
(SD style) per mm of stroke
Weight
Bore Table/General
Rod purpose type and cutting oil proof type Unit: kg
Weights
(mm) type
Standard Double Standard Double
14 MPa Double Acting Hydraulic Cylinder
Basic weight
type Additionalrod
rod type type weight
type LA LB LC FA FB Mounting FC FD FK FE FYweight
accessory FZ CA CS CB TA TC
View (SD style) per mm
Set of stroke
Bore Rod Switch Set Switch
Table of Weight Table/General purpose type
(mm)
φ32 type
B Standard
3.3 Double 4.1 Standard 0.008 0.3 0.3 0.48 0.1 0.6 0.6 0.9 1.1 - 0.2 0.7 0.4 - 0.5 0.1 0.5
0.006 Double Unit: kg
Contents A type 3.8 rod- 0.013 rod- - FA - FB FC FD FK - FE 0.9 FY FZ CA CS CB TA TC
Basic type type
weight (SD type LA LB weight
Additional LC
φ40 B Switch3.5Set 4.4 Switch
0.011Set 0.014 0.5 0.5 0.7 0.7 1.1 0.3 0.8Mounting
0.5 0.6 accessory
0.6 0.1 0.6weight
Bore style) per mm of stroke
0.63 0.2 1.2 -
φ32 B
C
Rod 3.3
3.4 4.1 0.010 0.008
4.3 0.006 0.012 0.3 0.3 0.48 0.1 0.6 0.6 0.9 1.1 - 0.2 0.7 0.4 - 0.5 0.1 0.5
(mm) A A 3.8
Standard
5.5 -
- Double -
0.013
0.017 - Standard - - -
Double
- -
- 0.9 1.5
type
φφØ40
50 B
B 3.5
5.0 type 4.4
6.4 0.011 rod 0.014
0.014 0.019 type 0.5
0.9 0.5
0.7 rod 0.7 1.2LA0.7 1.1
1.5 FA
2.0 FB FC 0.3
1.1 0.8
FD 0.5
1.6 0.6
1.1 0.6
1.0 FK FY0.1
1.2 0.6
0.4 FZ
1.0 CA CS CB TA TC
0.63 0.2
0.88 0.7 1.2
2.2 --
C
C 3.4
Switch
4.9 4.3
6.2 0.010
Set type 0.012
0.012 0.014Switch Set type
A
A 5.5
9.1 - 0.017 - - -
- - 1.5
32 B 3.3- 4.1 - 0.006
0.024 -
0.008 0.3 0.1 -0.62.3 0.6 0.9 1.1 0.2 0.7 0.4 - 0.5 0.1 0.5
φφ50
63 B
B 5.0
7.9 10.2 0.019 0.019
6.4 0.014 0.027 0.9 1.0 0.7
1.2 1.2
1.8 1.5
2.2 2.0
3.0 1.1
1.6 1.6
2.4 1.0
2.0 1.1
1.9 1.2
2.6 0.4
0.6 1.0
1.2
0.88
1.5 0.7
1.0 2.2
3.6 -
-
C
CA 4.9
7.6 3.8 6.29.8 0.012
0.017- 0.014
0.022 0.013 - - -
A
AB 9.1
18.0 - 0.024 - - - - 2.3
40 3.5- 4.4 - 0.011
0.039 -0.014- 0.5 0.2 -0.73.9 0.7 1.1 1.2 0.3 0.8 0.5 0.6 0.6 0.1 0.6
φφ63
80 B
B 7.9
16.2 10.2 0.032 0.027
20.3 0.019 0.045 1.0 1.8 1.2
2.0 1.8
3.0 2.2
2.8 3.0
4.7 1.6
2.1 2.4
4.0 2.0
3.0 1.9
3.6 2.6
3.6 0.6
0.6 1.2
2.1
1.5
2.5 1.0
1.1 3.6
4.7 -
-
CC
C 7.6 3.419.4
15.5 9.8 0.017 4.3 0.022
0.027 0.035 0.010 0.012 0.2 1.2
A
AA 18.0
29.6 5.5- - 0.039
0.060 -
- 0.017 - --
- - - 3.9
- 0.9 - - - 6.6 1.5 2.0 - 1.1 1.6 1.0 1.1 1.2 0.4 1.0
80
φφ100 B
B 16.2
26.0 20.3 0.048 0.045
32.7 0.032 0.067 1.8 2.1 2.0
2.9 3.0
4.8 2.8
4.6 4.7
7.4 2.1
3.9 4.0
6.9 3.0
5.5 3.6
6.7 3.6
6.7 0.6
1.0 2.1
3.8
2.5 1.8
3.63 1.1 4.7
8.9 -
-
50 C
CB 15.5
24.9 5.019.431.1 0.027 6.4 0.035
0.042 0.055 0.014 0.019 0.9 0.7 1.2 1.5 2.0 2.2 1.1 1.6 1.0 1.1 1.2 0.4 1.0
A
A 29.6
49.2 -
- 0.060
0.096 -
- - -
- - - 6.6
- 11.4
φφ100
125 B
BC 26.0
42.9 4.932.753.6 0.048 6.2 0.067
0.077 0.107 0.0122.1
3.2 2.9
5.5 0.014 4.8 8.40.94.6 7.4
0.7
8.0 13.0 1.2 1.5 3.9 6.9
2.0 5.5
6.2 12.1 6.7 12.1
9.9 2.2
12.8 6.7
1.11.0 3.8
2.1 1.6
6.2 1.0 1.1 1.2 0.4 1.0
3.63 1.8
6.88 2.9 8.9 -
12.6 -
C
C 24.9
42.5 31.1 0.065 0.055
52.7 0.042 0.084
A
A 49.2
9.1- 0.096
- -
0.024 -
- - - 11.4 -
A 67.5 0.122 - - - - - 14.9
φφ63125
140 B
BB 42.9
59.6 7.953.673.9 0.077 10.2 0.107
0.100 0.140 0.0193.2
3.8 5.5
7.7 0.027 11.1 8.41.08.0
9.2 13.0
1.0 1.8 2.2
17.1 6.2
8.2 12.1 9.9 3.6
3.016.7
16.1 12.8
- 12.1 1.62.1
21.0 6.2
2.4
4.1 11.1 2.0 1.9 2.6 0.6 1.2
9.63 2.9
6.88 3.2 12.6
20.4 --
C
C 42.5
56.0 52.7 0.085 0.084
69.6 0.065 0.111
C 7.6- 9.8 0.017 0.022 1.0 3.6
A
A 67.5
77.9 - 0.122
0.148 -
- - -
- - -
- 14.9
17.9
φφ140
150 BA
B 69.6 18.0
59.6 73.9
86.5 0.100
0.118- 0.140
0.162 0.0393.8
4.8 7.7
9.6 - 11.1 -
9.2 17.1
13.7 16.6 22.4 8.2 16.1
10.7 19.5 16.7
18.2 --- 21.0
26.8 4.1
4.6 11.1
10.9
12.0 3.2
9.63 4.9 1.8 20.4
3.0-
22.9 - 2.8 4.7 2.1 4.0 3.0 3.6 3.6 0.6 2.1
C 56.0
67.9 16.269.6
83.6 0.085
80 CB 20.3 0.111
0.101 0.127 0.032 0.045 1.1 4.7
A
A 77.9
93.0 -
- 0.148
0.148 -
- - -
- - -
- 17.9
21.5
φφ150
160 BC
B 84.3 15.5
69.6 86.5 0.118
114.6 19.4 0.162
0.121 0.171 0.0274.8 9.6 0.035 13.7
5.4 10.0 16.51.8
16.6 1.1 3.0 2.8
19.0 22.4
25.2 10.7 4.718.2
11.3 19.5
22.5 22.9 4.7
-
- 26.8 2.14.6
28.4 4.0 3.0
5.2 10.9
14.8 3.6 3.6 0.6 2.1
13.0 4.9
12.0 5.3 22.9
31.2 --
C
CA 67.9
79.9 29.683.6
99.1 0.101
0.102- 0.127
0.132 0.060 - 2.1 1.8 4.8 4.6 7.4 8.9 3.9 6.9 5.5 6.7 6.7 1.0 3.8
A 93.0 - 0.148 - - - - 21.5
100
φ160 BB 84.3 26.0 114.6 0.121 32.7 0.171 0.048 5.4 10.0 0.067 16.5 19.0 25.2 11.3 22.5 22.9 - 28.4 5.2 14.8
13.0 5.3 2.1 1.8 4.8- 4.6 7.4
31.2 8.9 3.9 6.9 5.5 6.7 6.7 1.0 3.8
CC 79.9 24.999.1 0.102 31.1 0.132 0.042 0.055
A 49.2 - 0.096 - - -
125 B 42.9 53.6 0.077 0.107 3.2 2.9 8.4 8.0 13.0 12.6 6.2 12.1 9.9 12.8 12.1 2.1 6.2
C 42.5 52.7 0.065 0.084 2.9 12.6
31 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Fluids and Seals 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents
alve and air vent positions depending Port, cushion and air vent positions for LA style
r bore (for rod A only)
■Water-glycol working fluid Port position Ⓐ Port position Ⓑ WF-WG:
f40, f50, f100, f140, Water-
Notes) f150 AFWF A WF-WG
glycol
1) Iron tubing (standard type) is plated with
hard chrome and tested with water-glycol fluid
fluid. D B D B
2) Stainless steel tubing (Switch Set) is not
plated in conformity with the standard
Air vent Cushion valve and
Cushion tested
valve with water-glycol fluid.
Air vent C C
D B D B
C C
32 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Fluids and Seals 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents
Working temperature range of packing material depending on working oil type
-100C 00C 800
C 1000C 1200C
0
Temperature ( C)
Working oil Packing material 140F 320F 176 0
F 2120F 2480F
0
Temperature ( F)
Nitrile rubber
Urethane rubber
Petroleum-based fluid
Fluoric rubber
Hydrogenated nitrile rubber
Nitrile rubber
Water-glycol fluid
Hydrogenated nitrile rubber
Nitrile rubber
Water in oil fluid
Hydrogenated nitrile rubber
Nitrile rubber
Oil in water fluid
Hydrogenated nitrile rubber
Notes) ● Use the packings applicable to working oil used within the working temperature range. Otherwise, substantial abrasion and
inferiority may occur to the packings.
● The temperature range shown in the table above is applicable to each packing material. For the switch sets, use them within
the working temperature range applicable to the switches.
1 Nitrile rubber � � ✕ � �
2 Urethane rubber �
� ✕ ✕ � �
3 Fluoric rubber � ✕ � � �
6 Hydrogenated nitrile rubber � �
� ✕ �
� �
�
Notes) * The �
� and � -marked items are applicable, while the ✕ -marked items are inapplicable. For the use of the � -marked
33 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Cylinder Safety Guide 14 MPa Double Acting Hydraulic Cylinder
View
Table of Safety Guide for Selecting and Using Hydraulic, Pneumatic Cylinders and Their Accessories
Contents
WARNING: FAILURE OF THE CYLINDER, ITS PARTS, ITS MOUNTING, ITS CONNECTIONS TO OTHER OBJECTS,
OR ITS CONTROLS CAN RESULT IN:
• Unanticipated or uncontrolled movement of the cylinder or objects connected to it.
• Falling of the cylinder or objects held up by it.
• Fluid escaping from the cylinder, potentially at high velocity.
THESE EVENTS COULD CAUSE DEATH OR PERSONAL INJURY BY, FOR EXAMPLE, PERSONS FALLING FROM
HIGH LOCATIONS, BEING CRUSHED OR STRUCK BY HEAVY OR FAST MOVING OBJECTS, BEING PUSHED INTO
DANGEROUS EQUIPMENT OR SITUATIONS, OR SLIPPING ON ESCAPED FLUID.
Before selecting or using Parker Hannifin Corporation (the Company) cylinders • Failure of the pressurized fluid delivery system (hoses, fittings, valves,
or related accessories, it is important that you read, understand and follow the pumps, compressors) which maintain cylinder position.
following safety information. Training is advised before selecting and using the • Catastrophic cylinder seal failure leading to sudden loss of pressurized
Company’s products. fluid.
1.0 General Instructions • Failure of the machine control system.
1.1 Scope – This safety guide provides instructions for selecting and using Follow the recommendations of the “Piston Rod Selection Chart and Data”
(including assembling, installing, and maintaining) cylinder products. This in the publication for the series of cylinders of interest. The suggested piston
safety guide is a supplement to and is to be used with the specific Company rod diameter in these charts must be followed in order to avoid piston rod
publications for the specific cylinder products that are being considered for buckling.
use.
Piston rods are not normally designed to absorb bending moments or loads
1.2 Fail Safe – Cylinder products can and do fail without warning for many which are perpendicular to the axis of piston rod motion. These additional
reasons. All systems and equipment should be designed in a fail-safe mode loads can cause the piston rod to fail. If these types of additional loads are
so that if the failure of a cylinder product occurs people and property won’t be expected to be imposed on the piston rod, their magnitude should be made
endangered. known to our engineering department.
1.3 Distribution – Provide a free copy of this safety guide to each person The cylinder user should always make sure that the piston rod is securely
responsible for selecting or using cylinder products. Do not select or use attached to the machine member.
the Company’s cylinders without thoroughly reading and understanding this On occasion cylinders are ordered with double rods (a piston rod extended
safety guide as well as the specific Company publications for the products from both ends of the cylinder). In some cases a stop is threaded on to one
considered or selected. of the piston rods and used as an external stroke adjuster. On occasions
1.4 User Responsibility – Due to very wide variety of cylinder applications spacers are attached to the machine member connected to the piston rod
and cylinder operating conditions, the Company does not warrant that any and also used as a stroke adjuster. In both cases the stops will create a pinch
particular cylinder is suitable for any specific application. This safety guide point and the user should consider appropriate use of guards. If these
does not analyze all technical parameters that must be considered in select- external stops are not perpendicular to the mating contact surface, or if debris
ing a product. The hydraulic and pneumatic cylinders outlined in this catalog is trapped between the contact surfaces, a bending moment will be placed
are designed to the Company’s design guidelines and do not necessarily on the piston rod, which can lead to piston rod failure. An external stop will
meet the design guideline of other agencies such as American Bureau of also negate the effect of cushioning and will subject the piston rod to impact
Shipping, ASME Pressure Vessel Code etc. The user, through its own loading. Those two (2) conditions can cause piston rod failure. Internal stroke
analysis and testing, is solely responsible for: adjusters are available with and without cushions. The use of external stroke
adjusters should be reviewed with our engineering department.
• Making the final selection of the cylinders and related accessories.
The piston rod to piston and the stud to piston rod threaded connections are
• Determining if the cylinders are required to meet specific design require- secured with an anaerobic adhesive. The strength of the adhesive decreases
ments as required by the Agency(s) or industry standards covering the with increasing temperature. Cylinders which can be exposed to tempera-
design of the user’s equipment. tures above +250°F (+121°C) are to be ordered with a non studded piston
• Assuring that the user’s requirements are met, OSHA requirements are rod and a pinned piston to rod joint.
met, and safety guidelines from the applicable agencies such as but not
limited to ANSI are followed and that the use presents no health or safety 2.3 Cushions – Cushions should be considered for cylinder applications
hazards. when the piston velocity is expected to be over 4 inches/second.
• Providing all appropriate health and safety warnings on the equipment on Cylinder cushions are normally designed to absorb the energy of a linear
which the cylinders are used. applied load. A rotating mass has considerably more energy than the same
mass moving in a linear mode. Cushioning for a rotating mass application
1.5 Additional Questions – Call the appropriate Company technical service should be reviewed by our engineering department.
department if you have any questions or require any additional information.
See the Company publication for the product being considered or used, or 2.4 Cylinder Mountings – Some cylinder mounting configurations may have
call 1-847-298-2400, or go to www.parker.com, for telephone numbers of the certain limitations such as but not limited to minimum stroke for side or foot
appropriate technical service department. mounting cylinders or pressure de-ratings for certain mounts. Carefully review
the catalog for these types of restrictions.
2.0 Cylinder and Accessories Selection Always mount cylinders using the largest possible high tensile alloy steel
2.1 Seals – Part of the process of selecting a cylinder is the selection of socket head cap screws that can fit in the cylinder mounting holes and torque
seal compounds. Before making this selection, consult the “seal information them to the manufacturer’s recommendations for their size.
page(s)” of the publication for the series of cylinders of interest.
2.5 Port Fittings – Hydraulic cylinders applied with meter out or decelera-
The application of cylinders may allow fluids such as cutting fluids, wash tion circuits are subject to intensified pressure at piston rod end.
down fluids etc. to come in contact with the external area of the cylinder.
These fluids may attack the piston rod wiper and or the primary seal and The rod end pressure is approximately equal to:
must be taken into account when selecting and specifying seal compounds. operating pressure x effective cap end area
Dynamic seals will wear. The rate of wear will depend on many operating effective rod end piston area
factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has
been improperly serviced. The user must take seal wear into consideration in Contact your connector supplier for the pressure rating of individual
the application of cylinders. connectors.
2.2 Piston Rods – Possible consequences of piston rod failure or 3.0 Cylinder and Accessories Installation and Mounting
separation of the piston rod from the piston include, but are not limited to are: 3.1 Installation
• Piston rod and or attached load thrown off at high speed. 3.1.1 – Cleanliness is an important consideration, and cylinders are
• High velocity fluid discharge. shipped with the ports plugged to protect them from contaminants enter-
ing the ports. These plugs should not be removed until the piping is to
• Piston rod extending when pressure is applied in the piston
be installed. Before making the connection to the cylinder ports, piping
retract mode.
should be thoroughly cleaned to remove all chips or burrs which might
Piston rods or machine members attached to the piston rod may move have resulted from threading or flaring operations.
suddenly and without warning as a consequence of other conditions
occurring to the machine such as, but not limited to:
• Unexpected detachment of the machine member from the piston rod.
34 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Cylinder Safety Guide 14 MPa Double Acting Hydraulic Cylinder
View
Table of
3.1.2 – Cylinders operating in an environment where air drying materials Rod seal leakage could also be traced to gland wear. If clearance
Contents are present such as fast-drying chemicals, paint, or weld splatter, or is excessive, replace rod bushing and seal. Rod seal leakage can
other hazardous conditions such as excessive heat, should have shields also be traced to seal deterioration. If seals are soft or gummy or
installed to prevent damage to the piston rod and piston rod seals. brittle, check compatibility of seal material with lubricant used if air
cylinder, or operating fluid if hydraulic cylinder. Replace with seal
3.1.3 – Proper alignment of the cylinder piston rod and its mating material, which is compatible with these fluids. If the seals are hard
component on the machine should be checked in both the extended and or have lost elasticity, it is usually due to exposure to temperatures
retracted positions. Improper alignment will result in excessive rod gland in excess of 165°F. (+74°C). Shield the cylinder from the heat
and/or cylinder bore wear. On fixed mounting cylinders attaching the pis- source to limit temperature to 350°F. (+177°C.) and replace with
ton rod while the rod is retracted will help in achieving proper alignment. fluorocarbon seals.
3.1.4 – Sometimes it may be necessary to rotate the piston rod in order 4.2.1.2 – Cylinder body seal leak can generally be traced to loose
to thread the piston rod into the machine member. This operation must tie rods. Torque the tie rods to manufacturer’s recommendation for
always be done with zero pressure being applied to either side of the that bore size.
piston. Failure to follow this procedure may result in loosening the piston
to rod-threaded connection. In some rare cases the turning of the piston Excessive pressure can also result in cylinder body seal leak.
rod may rotate a threaded piston rod gland and loosen it from the Determine maximum pressure to rated limits. Replace seals and
cylinder head. Confirm that this condition is not occurring. If it does, retorque tie rods as in paragraph above. Excessive pressure can
re-tighten the piston rod gland firmly against the cylinder head. also result in cylinder body seal leak. Determine if the pressure
rating of the cylinder has been exceeded. If so, bring the operating
For double rod cylinders it is also important that when attaching or pressure down to the rating of the cylinder and have the tie rods
detaching the piston rod from the machine member that the torque be replaced.
applied to the piston rod end of the cylinder that is directly attaching to
the machine member with the opposite end unrestrained. If the design Pinched or extruded cylinder body seal will also result in a leak.
of the machine is such that only the rod end of the cylinder opposite to Replace cylinder body seal and retorque as in paragraph above.
where the rod attaches to the machine member can be rotated, consult Cylinder body seal leakage due to loss of radial squeeze which
the factory for further instructions. shows up in the form of flat spots or due to wear on the O.D. or I.D.
3.2 Mounting Recommendations – Either of these are symptoms of normal wear due to high cycle
rate or length of service. Replace seals as per paragraph above.
3.2.1 – Always mount cylinders using the largest possible high tensile
alloy steel socket head screws that can fit in the cylinder mounting holes 4.2.2 – Internal Leakage
and torque them to the manufacturer’s recommendations for their size. 4.2.2.1 – Piston seal leak (by-pass) 1 to 3 cubic inches per minute
3.2.2 – Side-Mounted Cylinders – In addition to the mounting bolts, leakage is considered normal for piston ring construction. Virtually
cylinders of this type should be equipped with thrust keys or dowel pins no static leak with lipseal type seals on piston should be expected.
located so as to resist the major load. Piston seal wear is a usual cause of piston seal leakage. Replace
seals as required.
3.2.3 – Tie Rod Mounting – Cylinders with tie rod mountings are recom-
mended for applications where mounting space is limited. The standard 4.2.2.2 – With lipseal type piston seals excessive back pressure
tie rod extension is shown as BB in dimension tables. Longer or shorter due to over-adjustment of speed control valves could be a direct
extensions can be supplied. Nuts used for this mounting style should be cause of rapid seal wear. Contamination in a hydraulic system
torqued to the same value as the tie rods for that bore size. can result in a scored cylinder bore, resulting in rapid seal wear. In
either case, replace piston seals as required.
3.2.4 – Flange Mount Cylinders – The controlled diameter of the rod
gland extension on head end flange mount cylinders can be used 4.2.2.3 – What appears to be piston seal leak, evidenced by the
as a pilot to locate the cylinders in relation to the machine. After align- fact that the cylinder drifts, is not always traceable to the piston. To
ment has been obtained, the flanges may be drilled for pins or dowels to make sure, it is suggested that one side of the cylinder piston be
prevent shifting. pressurized and the fluid line at the opposite port be disconnected.
Observe leakage. If none is evident, seek the cause of cylinder drift
3.2.5 – Trunnion Mountings – Cylinders require lubricated bearing blocks in other component parts in the circuit.
with minimum bearing clearances. Bearing blocks should be carefully
aligned and rigidly mounted so the trunnions will not be subjected to 4.2.3 – Cylinder Fails to Move the Load
bending moments. The rod end should also be pivoted with the pivot pin 4.2.3.1 – Pneumatic or hydraulic pressure is too low. Check the
in line and parallel to axis of the trunnion pins. pressure at the cylinder to make sure it is to circuit requirements.
3.2.6 – Clevis Mountings – Cylinders should be pivoted at both ends 4.2.3.2 – Piston Seal Leak – Operate the valve to cycle the cylinder
with centerline of pins parallel to each other. After cylinder is mounted, and observe fluid flow at valve exhaust ports at end of cylinder
be sure to check to assure that the cylinder is free to swing through its stroke. Replace piston seals if flow is excessive.
working arc without interference from other machine parts.
4.2.3.3 – Cylinder is undersized for the load – Replace cylinder with
4.0 Cylinder and Accessories Maintenance, Troubleshooting one of a larger bore size.
and Replacement
4.3 Erratic or Chatter Operation
4.1 Storage – At times cylinders are delivered before a customer is ready to
install them and must be stored for a period of time. When storage is required 4.3.1 – Excessive friction at rod gland or piston bearing due to load
the following procedures are recommended. misalignment – Correct cylinder-to-load alignment.
4.1.1 – Store the cylinders in an indoor area which has a dry, clean and 4.3.2 – Cylinder sized too close to load requirements – Reduce load or
noncorrosive atmosphere. Take care to protect the cylinder from both install larger cylinder.
internal corrosion and external damage. 4.3.3 – Erratic operation could be traced to the difference between static
4.1.2 – Whenever possible cylinders should be stored in a vertical posi- and kinetic friction. Install speed control valves to provide a back pres-
tion (piston rod up). This will minimize corrosion due to possible conden- sure to control the stroke.
sation which could occur inside the cylinder. This will also minimize seal
4.4 Cylinder Modifications, Repairs, or Failed Component – Cylinders
damage.
as shipped from the factory are not to be disassembled and or modified.
4.1.3 – Port protector plugs should be left in the cylinder until the time of If cylinders require modifications, these modifications must be done at
installation. company locations or by the Company’s certified facilities. The Cylinder
4.1.4 – If a cylinder is stored full of hydraulic fluid, expansion of the fluid Division Engineering Department must be notified in the event of
due to temperature changes must be considered. Installing a check a mechanical fracture or permanent deformation of any cylinder component
valve with free flow out of the cylinder is one method. (excluding seals). This includes a broken piston rod, tie rod, mounting
accessory or any other cylinder component. The notification should include
4.1.5 – When cylinders are mounted on equipment that is stored outside all operation and application details. This information will be used to provide
for extended periods, exposed unpainted surfaces, e.g. piston rod, must an engineered repair that will prevent recurrence of the failure.
be coated with a rust-inhibiting compound to prevent corrosion. It is allowed to disassemble cylinders for the purpose of replacing seals or
seal assemblies. However, this work must be done by strictly following all the
4.2 Cylinder Trouble Shooting instructions provided with the seal kits.
4.2.1 – External Leakage
4.2.1.1 – Rod seal leakage can generally be traced to worn or
damaged seals. Examine the piston rod for dents, gouges or score
marks, and replace piston rod if surface is rough.
35 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Offer of Sale 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents Offer of Sale
The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors (“Seller”)
are hereby offered for sale at prices to be established by Seller. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and
Conditions. Buyer’s order for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this offer. All goods, services
or work described will be referred to as “Products”.
1. Terms and Conditions. Seller’s willingness to offer Products, or accept an order infringement or any other claim, brought by or incurred by Buyer, Buyer’s employees,
for Products, to or from Buyer is subject to these Terms and Conditions or any newer or any other person, arising out of: (a) improper selection, improper application or other
version of the terms and conditions found on-line at www.parker.com/saleterms/. Seller misuse of Products purchased by Buyer from Seller; (b) any act or omission, negligent
objects to any contrary or additional terms or conditions of Buyer’s order or any other or otherwise, of Buyer; (c) Seller’s use of patterns, plans, drawings, or specifications
document issued by Buyer. furnished by Buyer to manufacture Product; or (d) Buyer’s failure to comply with these
2. Price Adjustments; Payments. Prices stated on Seller’s quote or other documen- terms and conditions. Seller shall not indemnify Buyer under any circumstance except
tation offered by Seller are valid for 30 days, and do not include any sales, use, or other as otherwise provided.
taxes unless specifically stated. Unless otherwise specified by Seller, all prices are 12. Cancellations and Changes. Orders shall not be subject to cancellation or
F.C.A. Seller’s facility (INCOTERMS 2010). Payment is subject to credit approval and change by Buyer for any reason, except with Seller’s written consent and upon terms
is due 30 days from the date of invoice or such other term as required by Seller’s Credit that will indemnify, defend and hold Seller harmless against all direct, incidental and
Department, after which Buyer shall pay interest on any unpaid invoices at the rate of consequential loss or damage. Seller may change product features, specifications,
1.5% per month or the maximum allowable rate under applicable law. designs and availability with notice to Buyer.
3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and 13. Limitation on Assignment. Buyer may not assign its rights or obligations under
Seller shall not be responsible for any damages resulting from any delay. Regardless this agreement without the prior written consent of Seller.
of the manner of shipment, title to any products and risk of loss or damage shall pass 14. Force Majeure. Seller does not assume the risk and shall not be liable for delay
to Buyer upon placement of the products with the shipment carrier at Seller’s facility. or failure to perform any of Seller’s obligations by reason of circumstances beyond the
Unless otherwise stated, Seller may exercise its judgment in choosing the carrier and reasonable control of Seller (hereinafter “Events of Force Majeure”). Events of Force
means of delivery. No deferment of shipment at Buyers’ request beyond the respec- Majeure shall include without limitation: accidents, strikes or labor disputes, acts of
tive dates indicated will be made except on terms that will indemnify, defend and hold any government or government agency, acts of nature, delays or failures in delivery
Seller harmless against all loss and additional expense. Buyer shall be responsible for from carriers or suppliers, shortages of materials, or any other cause beyond Seller’s
any additional shipping charges incurred by Seller due to Buyer’s acts or omissions. reasonable control.
4. Warranty. Seller warrants that the Products sold hereunder shall be free from 15. Waiver and Severability. Failure to enforce any provision of this agreement will
defects in material or workmanship for a period of eighteen months from the date of not waive that provision nor will any such failure prejudice Seller’s right to enforce that
delivery to Buyer. The prices charged for Seller’s products are based upon the exclu- provision in the future. Invalidation of any provision of this agreement by legislation or
sive limited warranty stated above, and upon the following disclaimer: DISCLAIMER other rule of law shall not invalidate any other provision herein. The remaining provi-
OF WARRANTY: THIS WARRANTY COMPRISES THE SOLE AND ENTIRE sions of this agreement will remain in full force and effect.
WARRANTY PERTAINING TO PRODUCTS PROVIDED HEREUNDER. SELLER
DISCLAIMS ALL OTHER WARRANTIES, EXPRESS AND IMPLIED, INCLUDING 16. Termination. Seller may terminate this agreement for any reason and at any time
DESIGN, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. by giving Buyer thirty (30) days written notice of termination. Seller may immediately
terminate this agreement, in writing, if Buyer: (a) commits a breach of any provision of
5. Claims; Commencement of Actions. Buyer shall promptly inspect all Products this agreement (b) appointments a trustee, receiver or custodian for all or any part of
upon delivery. No claims for shortages will be allowed unless reported to the Seller Buyer’s property (c) files a petition for relief in bankruptcy on its own behalf, or by a third
within 10 days of delivery. No other claims against Seller will be allowed unless party (d) makes an assignment for the benefit of creditors, or (e) dissolves or liquidates
asserted in writing within 30 days after delivery. Buyer shall notify Seller of any alleged all or a majority of its assets.
breach of warranty within 30 days after the date the defect is or should have been
discovered by Buyer. Any action based upon breach of this agreement or upon any 17. Governing Law. This agreement and the sale and delivery of all Products here-
other claim arising out of this sale (other than an action by Seller for an amount due on under shall be deemed to have taken place in and shall be governed and construed
any invoice) must be commenced within 12 months from the date of the breach without in accordance with the laws of the State of Ohio, as applicable to contracts executed
regard to the date breach is discovered. and wholly performed therein and without regard to conflicts of laws principles. Buyer
irrevocably agrees and consents to the exclusive jurisdiction and venue of the courts
6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS of Cuyahoga County, Ohio with respect to any dispute, controversy or claim arising out
OPTION, REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR REFUND THE of or relating to this agreement.
PURCHASE PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO BUYER FOR
ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES 18. Indemnity for Infringement of Intellectual Property Rights. Seller shall have
ARISING OUT OF, OR AS THE RESULT OF, THE SALE, DELIVERY, NON- no liability for infringement of any patents, trademarks, copyrights, trade dress, trade
DELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCTS OR ANY secrets or similar rights except as provided in this Section. Seller will defend and
PART THEREOF, OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks,
INCURRED WITHOUT SELLER’S WRITTEN CONSENT, EVEN IF SELLER copyrights, trade dress and trade secrets (“Intellectual Property Rights”). Seller will
HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR OTHER LEGAL defend at its expense and will pay the cost of any settlement or damages awarded in
THEORY. IN NO EVENT SHALL SELLER’S LIABILITY UNDER ANY CLAIM MADE an action brought against Buyer based on an allegation that a Product sold pursuant to
BY BUYER EXCEED THE PURCHASE PRICE OF THE PRODUCTS. this Agreement infringes the Intellectual Property Rights of a third party. Seller’s obliga-
tion to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten
7. User Responsibility. The user, through its own analysis and testing, is solely (10) days after Buyer becomes aware of such allegations of infringement, and Seller
responsible for making the final selection of the system and Product and assuring that having sole control over the defense of any allegations or actions including all negotia-
all performance, endurance, maintenance, safety and warning requirements of the tions for settlement or compromise. If a Product is subject to a claim that it infringes the
application are met. The user must analyze all aspects of the application and follow Intellectual Property Rights of a third party, Seller may, at its sole expense and option,
applicable industry standards and Product information. If Seller provides Product or procure for Buyer the right to continue using the Product, replace or modify the Product
system options, the user is responsible for determining that such data and specifica- so as to make it noninfringing, or offer to accept return of the Product and return the
tions are suitable and sufficient for all applications and reasonably foreseeable uses purchase price less a reasonable allowance for depreciation. Notwithstanding the fore-
of the Products or systems. going, Seller shall have no liability for claims of infringement based on information
8. Loss to Buyer’s Property. Any designs, tools, patterns, materials, drawings, confi- provided by Buyer, or directed to Products delivered hereunder for which the designs
dential information or equipment furnished by Buyer or any other items which become are specified in whole or part by Buyer, or infringements resulting from the modification,
Buyer’s property, will be considered obsolete and may be destroyed by Seller after two combination or use in a system of any Product sold hereunder. The foregoing provi-
consecutive years have elapsed without Buyer ordering the items manufactured using sions of this Section shall constitute Seller’s sole and exclusive liability and Buyer’s
such property. Seller shall not be responsible for any loss or damage to such property sole and exclusive remedy for infringement of Intellectual Property Rights.
while it is in Seller’s possession or control. 19. Entire Agreement. This agreement contains the entire agreement between the
9. Special Tooling. A tooling charge may be imposed for any special tooling, includ- Buyer and Seller and constitutes the final, complete and exclusive expression of the
ing without limitation, dies, fixtures, molds and patterns, acquired to manufacture terms of sale. All prior or contemporaneous written or oral agreements or negotiations
Products. Such special tooling shall be and remain Seller’s property notwithstanding with respect to the subject matter are herein merged.
payment of any charges by Buyer. In no event will Buyer acquire any interest in appa- 20. Compliance with Law, U. K. Bribery Act and U.S. Foreign Corrupt Practices
ratus belonging to Seller which is utilized in the manufacture of the Products, even if Act. Buyer agrees to comply with all applicable laws and regulations, including both
such apparatus has been specially converted or adapted for such manufacture and those of the United Kingdom and the United States of America, and of the country or
notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have countries of the Territory in which Buyer may operate, including without limitation the
the right to alter, discard or otherwise dispose of any special tooling or other property U. K. Bribery Act, the U.S. Foreign Corrupt Practices Act (“FCPA”) and the U.S. Anti-
in its sole discretion at any time. Kickback Act (the “Anti-Kickback Act”), and agrees to indemnify and hold harmless
10. Buyer’s Obligation; Rights of Seller. To secure payment of all sums due or oth- Seller from the consequences of any violation of such provisions by Buyer, its employ-
erwise, Seller shall retain a security interest in the goods delivered and this agreement ees or agents. Buyer acknowledges that they are familiar with the provisions of the
shall be deemed a Security Agreement under the Uniform Commercial Code. Buyer U. K. Bribery Act, the FCPA and the Anti-Kickback Act, and certifies that Buyer will
authorizes Seller as its attorney to execute and file on Buyer’s behalf all documents adhere to the requirements thereof. In particular, Buyer represents and agrees that
Seller deems necessary to perfect its security interest. Buyer shall not make any payment or give anything of value, directly or indirectly to
11. Improper use and Indemnity. Buyer shall indemnify, defend, and hold Seller any governmental official, any foreign political party or official thereof, any candidate
harmless from any claim, liability, damages, lawsuits, and costs (including attorney for foreign political office, or any commercial entity or person, for the purpose of influ-
fees), whether for personal injury, property damage, patent, trademark or copyright encing such person to purchase products or otherwise benefit the business of Seller.
36 Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Catalog HY08-T1151-1/NA
Notes 14 MPa Double Acting Hydraulic Cylinder
View
Table of
Contents Notes
Taiyo America
St. Marys, Ohio
www.taiyoamericacylinders.com USA
Taiyo America
1700 East Spring Street
St. Marys, Ohio 45885 USA
phone (419) 300-8811
fax (419) 300-9765
www.taiyoamericacylinders.com