Professional Documents
Culture Documents
Brocade 143-080
Brocade 143-080
QUESTION NO: 1
When attempting to use the Access Gateway functionality to attach blade servers to your existing
fabric, you are unable to successfully set the switch to Access Gateway mode.
Answer: B
Explanation:
QUESTION NO: 2
Which three switches support Access Gateway mode running Fabric OS v7.0? (Choose three.)
A. Brocade 5100
B. Brocade 5300
C. Brocade 6510
D. Brocade 8000
E. Brocade DCX
Answer: A,C,D
Explanation:
QUESTION NO: 3
Which three statements about Advanced Performance Monitoring features on switches in Access
Gateway mode are true? (Choose three.)
QUESTION NO: 4
You want to form an F_Port trunk between a Brocade Fibre Channel Host Bus Adapter (HBA) and
a Brocade Fibre Channel switch.
Answer: A,C,E
Explanation:
QUESTION NO: 5
Target Rate Limiting can be implemented on which two Brocade adapters shown in the exhibit?
(Choose two.)
A. A
B. B
C. C
D. D
Answer: B,D
Explanation:
QUESTION NO: 6
You are asked to attach a Brocade 6510 into an existing 16 Gbps Brocade fabric without adding
an additional Domain ID into the existing fabric.
Answer: A
Explanation:
QUESTION NO: 7
You need to allow for multiple NPIV logins to a single port on a Brocade 6510.
A. switch
B. HBA
C. device
D. Access Gateway
Answer: A
Explanation:
QUESTION NO: 8
What is the port type on an Access Gateway that connects to a Brocade 6510?
A. N_Port
B. F_Port
C. E_Port
D. G_Port
Answer: A
Explanation:
QUESTION NO: 9
Answer: C
Explanation:
QUESTION NO: 10
Which three protocols do Brocade 1860 fabric adapters allow? (Choose three.)
A. FCoE
B. Native FC
C. TCP/IP
D. FCIP
E. FICON
Answer: A,B,C
Explanation:
QUESTION NO: 11
Which two statements are true about the zero-based area assignment port-addressing mode for
virtual fabrics? (Choose two.)
A. The mode allows for use of port blades with port indexes greater than 256.
B. The mode is compatible with domain, index zoning.
C. The area address of the first port assigned to the domain is set to zero.
D. The area address assignments are based on the port index.
Answer: A,C
Explanation:
QUESTION NO: 12
Which two statements are true about enabling the forward error correction feature? (Choose two.)
Answer: A,C
Explanation:
QUESTION NO: 13
You want to establish ICL trunking between platforms in the Brocade DCX 8510 family.
Answer: A,D
Explanation:
QUESTION NO: 14
You are attempting to set up an extended distance ISL between a Brocade DCX and a Brocade
300 platform. You have connected the cable but the link will not come up.
Which two settings need to be corrected in the exhibit to allow the ISL to form? (Choose two.)
A. Trunking
B. VC Link Init
C. Long Distance mode
D. port speed
Answer: C,D
Explanation:
QUESTION NO: 15
You are attempting to set up a two link trunk between the Brocade 5300 and Brocade 300
switches. You notice that the links are coming up as E_Ports and not as trunked ports.
Referring to the exhibit, which two changes need to be made on your Brocade 300 switch to allow
a trunk to form? (Choose two.)
A. VC Link Init
B. port grouping
C. ISL R_RDY
D. locked G_Port
Answer: B,C
Explanation:
QUESTION NO: 16
How many separate trunk groups will be formed between the Brocade DCX 8510-8 Backbones
shown in the exhibit?
A. 1
B. 2
C. 4
D. 8
Answer: C
Explanation:
QUESTION NO: 17
In the exhibit, if the master port goes offline, what will occur?
Answer: A
Explanation:
QUESTION NO: 18
You have decided to use trunking between a Brocade HBA and a Brocade switch in your fabric.
Answer: A
Explanation:
You are implementing two Brocade DCX 8510-8 backbones. You need to connect the two
backbones without consuming user ports.
A. ISLs
B. ICLs
C. F_Port trunking
D. Extended Fabric trunking
Answer: B
Explanation:
QUESTION NO: 20
You need more bandwidth in your fabric and decide to implement trunking.
A. All of the ports in a trunk group must be configured for the same distance mode.
B. You do not need a Trunking license for each switch that participates in trunking.
C. All the ports in a trunk group may belong to different port groups.
D. All the ports in a trunk group must have the same encryption and compression settings.
Answer: A,D
Explanation:
QUESTION NO: 21
You are using in-flight encryption in your fabric and you want to implement trunking.
A. 2
B. 4
C. 8
D. 16
Answer: A
QUESTION NO: 22
A. You can implement F_Port trunking between F_Ports on a Fabric OS switch and N_Ports on an
Access Gateway.
B. You can configure F_Port trunking on the F_Ports of an Access Gateway.
C. You can implement F_Port trunking between F_Ports on a Fabric OS switch and N_Ports on a
Brocade adapter.
D. You can configure F_Ports to be E_Ports with F_Port trunking on a Fabric OS switch.
Answer: A,C
Explanation:
QUESTION NO: 23
You are implementing two Brocade DCX 8510-8 backbones, a host with a dual port 16 Gbps
adapter, and a storage array. You are required to aggregate the host ports attaching to the fabric.
A. Brocade adapter
B. FCIP Trunking
C. F_Port Trunking
D. Extended Fabric
Answer: A,C
Explanation:
QUESTION NO: 24
which two types of trunking are used in the non-routed fabric shown in the exhibit? (Choose two.)
A. F_Port
B. ISL
C. EX_Port
D. ICL
Answer: A,D
Explanation:
QUESTION NO: 25
which two types of trunking are used in the non-routed fabric shown in the exhibit? (Choose two.)
A. F_Port
B. ISL
C. EX_Port
D. ICL
Answer: A,B
Explanation:
QUESTION NO: 26
Which license is required to enable all ICL connections between two Brocade DCX 8510-4
Backbones?
A. ICL 8-link
Answer: C
Explanation:
QUESTION NO: 27
Which two licenses are required to enable all ICL connections between two Brocade DCX 8510-8
Backbones? (Choose two.)
A. ICL 8-link
B. ICL 16-link
C. Inter Chassis Link (1st POD)
D. Inter Chassis Link (2nd POD)
Answer: C,D
Explanation:
QUESTION NO: 28
Which two licenses can be evaluated using a Time-Based license prior to purchasing? (Choose
two.)
A. Adaptive Networking
B. ICL
C. Ports on Demand
D. Trunking
Answer: A,D
Explanation:
QUESTION NO: 29
which two port types are used between the two fabrics? (Choose two.)
A. E
B. EX
C. VE
D. VEX
Answer: C,D
Explanation:
QUESTION NO: 30
Which two port types are shown in the exhibit? (Choose two.)
A. E
B. F
C. N
D. VE
Answer: B,C
Explanation:
QUESTION NO: 31
Which two port types are used in the FC-FC routed fabrics shown in the exhibit? (Choose two.)
A. E
B. EX
C. VE
D. VEX
Answer: A,B
Explanation:
QUESTION NO: 32
You are using a Brocade 1860 Fabric Adapter to connect to FC SAN storage which is connected
to a Brocade DCX. Which two solutions allow connectivity between the server and storage?
(Choose two.)
A. Connect both Fabric Adapter ports to an FC8-32 blade in the DCX and enable Mixed-Mode on
the adapter ports.
B. Connect both Fabric Adapter ports to an FCoE10-24 blade in the DCX and enable Mixed-Mode
on the adapter ports.
Answer: C,D
Explanation:
QUESTION NO: 33
A host is located 100 km from a virtual tape subsystem target. The system architect implements
two tunnels across two different FCIP links connecting their pair of Brocade DCX 8510-8s for
redundancy. Which two changes will increase performance? (Choose two.)
Answer: A,B
Explanation:
QUESTION NO: 34
An FCTrace of the FCIP links between two Brocade switches indicates that exchange commands
are being responded to on different FCIP tunnels with Fastwrite and OSTP enabled on the links.
What causes the exchange command and response to traverse the same tunnel?
A. port-based routing
B. in-order delivery
C. traffic isolation zones
D. frame redirection zones
Answer: C
Explanation:
QUESTION NO: 35
You are using a Brocade 1020 CNA to connect to IP storage and FC SAN storage which are both
connected to a Brocade DCX. Which solution allows connectivity between the server and storage?
Answer: A
Explanation:
QUESTION NO: 36
You have a security requirement to restrict which Fibre Channel end nodes can connect to your
fabric. Which policy satisfies this requirement?
A. FCS
B. DCC
C. SCC
D. IPFILTER
Answer: B
Explanation:
QUESTION NO: 37
You have a security requirement to restrict the switches that can join your fabric.
A. FCS
B. DCC
C. SCC
D. IPFILTER
Answer: C
Explanation:
QUESTION NO: 38
You have a security requirement to restrict the switches that can make changes to the
A. FCS
B. DCC
C. SCC
D. IPFILTER
Answer: A
Explanation:
QUESTION NO: 39
You have been instructed to use a provided certificate to enable secure management access to
your fabric devices while also integrating logins with your current company infrastructure.
A. RADIUS
B. LDAP
C. RBAC
D. SNMP
Answer: B
Explanation:
QUESTION NO: 40
You need to prevent the addition of a new switch to the fabric as shown in the exhibit.
A. Create an SCC policy with DID2 and DID4; save the SCC policy.
B. Create an FCS policy with DID2 and DID4; save the FCS policy.
C. Create an SCC policy with DID2 and DID4; activate the SCC policy.
D. Create an FCS policy with DID2 and DID4; activate the FCS policy.
QUESTION NO: 41
You implemented an SCC policy in a fabric consisting of two Brocade 6510 switches:
switch:admin> secpolicyactivate
Answer: C
Explanation:
QUESTION NO: 42
You have recently implemented LDAP to make sure that administrators can access the Brocade
DCX 8510-8 using their Microsoft Active Directory accounts. You run the ldapcfg -–maprole
DCX_8510 user command.
Which two statements are true for the members of the "DCX_8510" group in Active Directory?
(Choose two.)
Answer: A,D
Explanation:
QUESTION NO: 43
You need to restrict the users who are allowed to access a new Brocade DCX 8510-8. The user
credentials and passwords must be centralized and identical on all Brocade DCX 8510-8s.
Answer: A,D
Explanation:
QUESTION NO: 44
You need to ensure that changes to the fabric can only be initiated from the switch in data center
DC1.
A. Create an SCC policy on the switch with DID2; save the SCC policy.
B. Create an FCS policy on the switch with DID2; save the FCS policy.
Answer: D
Explanation:
QUESTION NO: 45
Which two statements are true about Access Gateway N_Port failover? (Choose two.)
A. It changes the F_Port to N_Port mapping in the event of an F_Port link failure.
B. It changes the F_Port to N_Port mapping in the event of an N_Port link failure.
C. It changes the F_Port's FC address based on the new N_Port.
D. It changes the N_Port's FC address to match the F_Port address to allow non-disruptive
failover.
Answer: B,C
Explanation:
QUESTION NO: 46
Answer: B
Explanation:
QUESTION NO: 47
You are using ag --wwnmapshow to display static and dynamic mapping information about all
device WWNs connected to your Access Gateway.
Answer: A,D,E
Explanation:
QUESTION NO: 48
Answer: A,D
Explanation:
QUESTION NO: 49
Answer: C
Explanation:
QUESTION NO: 50
Referring to the exhibit, which statement is true for a server connected to port 1 of the Access
Gateway?
A. The server will lose connectivity if port 16 of the Access Gateway goes down.
B. The server will lose connectivity if port 17 of the Access Gateway goes down.
C. The server will failover to port 17 if port 16 of the Access Gateway goes down.
D. The server will failover to port 23 if port 17 of the Access Gateway goes down.
Answer: A
Explanation:
QUESTION NO: 51
Which feature is used when connecting a Brocade 6510 in Access Gateway mode to different
fabrics while maintaining device-to-fabric consistency?
Answer: D
Explanation:
QUESTION NO: 52
You notice that some N_Ports on a Brocade 6510 in Access Gateway mode are heavily used
while others are not. You want to balance the utilization.
Answer: B
Explanation:
QUESTION NO: 53
Which two statements about Access Gateway mode are true? (Choose two.)
Answer: A,D
Explanation:
QUESTION NO: 54
Which three advantages does trunking provide when in Access Gateway mode? (Choose three.)
Answer: C,D,E
Explanation:
QUESTION NO: 55
Which two statements are true about Brocade trunking when connected to a Brocade switch in
Answer: A,B
Explanation:
QUESTION NO: 56
Which three devices are supported by a switch in Access Gateway mode? (Choose three.)
A. FICON channel
B. FCP initiators
C. FCP targets
D. fabric switches
E. iSCSI initiators
Answer: B,C,D
Explanation:
QUESTION NO: 57
Which two initialization stages must be completed to allow a host connected to an Access
Gateway (AG) device to send data frames through the fabric connected port? (Choose two.)
A. N_Ports perform the FLOGI command and the acceptance sequence with the fabric.
B. FDISC is used by the host to discover the AG.
C. FLOGI from the AG connected host is converted to FDISC by the AG.
D. FDISC is used by the AG device to discover the attached fabric.
Answer: A,C
Explanation:
QUESTION NO: 58
What must you do to ensure the Brocade Network Advisor operates correctly?
A. Verify the ports between your client and server and open the required ones.
B. Increase the clock rate of the server to greater than 3.2 GHz.
C. Increase the disk size to greater than 160 GB.
D. Increase server to a quad-core processor.
Answer: A
Explanation:
QUESTION NO: 59
Which two statements are true about Brocade Network Advisor? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 60
You have been using Web Tools for configuring and monitoring your medium-size SAN.
Management is requiring you to improve security in your data center.
Answer: B
Explanation:
QUESTION NO: 61
You are discovering the edge fabric using Brocade Network Advisor 11.0.x.
Referring to the exhibit, which switch should be selected as the seed switch?
A. Brocade 7800
B. Brocade 300
C. Brocade 5100
D. Brocade DCX-4S
Answer: B
Explanation:
QUESTION NO: 62
Which management application changes your Brocade SMI integrated agent security settings?
Answer: C
Explanation:
QUESTION NO: 63
You have encountered an issue with your Brocade Network Advisor 11.0.x client whereby the
topology view is not updating. You are going to escalate to your support provider.
Answer: B
Explanation:
QUESTION NO: 64
You need to collect data from your Brocade 6510. The data must be encrypted.
A. SNMPv3
B. IPv6
C. IPFilter
D. RPC
Answer: A
Explanation:
QUESTION NO: 65
Answer: D
Explanation:
QUESTION NO: 66
You must manage the zoning on four Brocade DCX 8510-8 fabrics.
Answer: D
Explanation:
QUESTION NO: 67
You need to graph real-time data from various elements of your SAN using Brocade Network
Advisor. Which three objects can be graphed? (Choose three.)
A. EE monitor
B. NPIV device
C. FCIP tunnel
D. management network traffic
E. managed CNA traffic
Answer: A,C,E
Explanation:
Answer: D
Explanation:
QUESTION NO: 69
You have just run the free versions of the SAN Health Diagnostics Capture utility and SAN Health
Professional.
Which three critical tasks can you perform based on this report? (Choose three.)
Answer: A,D,E
Explanation:
QUESTION NO: 70
You have been asked to collect real-time performance data on the 8 Gbps ISLs within your fabric
to troubleshoot problems being reported by users.
A. DCFM
B. SAN Health
C. NET Health
D. Brocade Network Advisor
QUESTION NO: 71
Several different application owners have complained that they are having performance issues
with their applications.
Referring to the output shown in the exhibit, which statement is true regarding this storage port?
Answer: A
Explanation:
QUESTION NO: 72
A. port
B. fabric
C. device
D. filter
Answer: A,B
Explanation:
QUESTION NO: 73
You believe you have a server that is timing out. In Fabric OS v7.0 you want to find discarded
frames due to timeout reasons.
A. spinfab
B. Frame Viewer
C. firmware history log
D. RASlog
Answer: B
Explanation:
QUESTION NO: 74
You are having congestion problems on your Fabric OS v7.0 fabric and want to locate the Top
Talkers on the ISLs and the F_Ports at the same time.
A. APM
B. HCM
C. NET Health
D. SAN Health
Answer: A
Explanation:
QUESTION NO: 75
You need to see real-time performance information from both Brocade DCX 8510-8 Backbones
and Brocade 825 Host Bus Adapters using one tool.
Answer: A
Explanation:
QUESTION NO: 76
One of the storage ports on your new Brocade DCX 8510-4 is heavily loaded. This port is shared
among multiple servers connected to the same Brocade DCX 8510-4. You need to determine
which server is causing the load on the storage port.
Answer: B
Explanation:
QUESTION NO: 77
For planning purposes, you need to provide a monthly analysis of ISL traffic to your management.
A. Fabric Watch
B. Web Tools
C. Brocade Network Advisor
D. Top Talkers
Answer: C
Explanation:
QUESTION NO: 78
Which two statements are true about traffic isolation (TI) zones? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 79
Answer: C,D
Explanation:
QUESTION NO: 80
Which two statements are true about QoS zone-based traffic prioritization? (Choose two.)
Answer: A,B
Explanation:
QUESTION NO: 81
You need to identify the devices which are using the greatest percent of bandwidth on an ISL of a
Brocade 6510.
Answer: B
Explanation:
QUESTION NO: 82
You want to use QoS to define the traffic priority in your mixed speed fabric. You use the
zonecreate "QOSL2_ora_prod", "10:00:00:00:30:00:00:00;50:00:00:00:40:a1:37:02" command.
Then you save and enable the new configuration to the fabric.
What are two ways this process will affect the devices listed in the command? (Choose two.)
A. The devices will be given a lower priority than non-QoS devices using the same path.
B. The devices will be given a higher priority than non-QoS devices using the same path.
C. The device priority will not be changed compared to non-QoS devices using the same path.
D. The traffic between these two devices will be affected when the link becomes saturated.
Answer: A,D
Explanation:
QUESTION NO: 83
Which two statements about TI zones over FC routers are true? (Choose two.)
A. Traffic isolation zones failover mode must be enabled in the edge fabrics and backbone fabric.
B. Traffic isolation over FC-FC routing is supported from edge fabric to edge fabric.
C. Traffic isolation zones failover mode must be disabled in the edge fabrics.
D. Traffic isolation over FC-FC routing is supported from backbone devices to edge devices.
Answer: A,B
Explanation:
QUESTION NO: 84
You are asked to set up TI zones over FCR to provide a dedicated path between Host 1 in edge
Referring to the exhibit, which traffic isolation zone should be implemented on Edge fabric 1?
Answer: C
Explanation:
QUESTION NO: 85
Which two statements are true for bottleneck detection? (Choose two.)
Answer: A,C
Explanation:
You have set up an End-to-End monitor for an E_Port trunk. You configure a monitor on that trunk.
What happens when the master port goes offline?
A. End-to-end monitoring is disabled until that initial master comes back online.
B. End-to-end monitoring moves to the new master port.
C. End-to-end monitoring is moved to the last slave to come online.
D. End-to-end monitoring is applied to all other ports in the trunk group.
Answer: B
Explanation:
QUESTION NO: 87
Which two Brocade Fabric OS features, when combined, can provide this functionality? (Choose
two.)
A. bottleneck detection
B. admin domains
C. virtual fabrics
D. ingress rate limiting
Answer: A,D
Explanation:
QUESTION NO: 88
A new system has been deployed requiring that data flows from two servers to their storage
targets to be given high priority. Congestion problems of one of the flows must not affect the other.
Referring to the exhibit, which zoning configuration will guarantee this behavior?
A. 1
B. 2
C. 3
D. 4
Answer: C
Explanation:
QUESTION NO: 89
You have deployed Top Talkers in your fabric. You have chosen to use Fabric mode.
QUESTION NO: 90
What is the maximum number of Virtual Channels (VCs) that are used when traffic is flowing for
the QoS zoning configuration shown in the exhibit?
A. 1
B. 2
C. 3
D. 4
Answer: C
Explanation:
QUESTION NO: 91
You have decided to enable ingress rate limiting on a port in your SAN.
A. The port must be disabled and then enabled before the feature will take effect.
B. You must specify the rate limit.
C. The rate limit will dynamically adapt to the congestion level on the port.
D. Enabling ingress rate limiting on the port is non-disruptive.
Answer: B,D
QUESTION NO: 92
To provide a required service level to a customer, you must configure traffic isolation zones.
Answer: C
Explanation:
QUESTION NO: 93
A. M_Ports
B. D_Ports
C. ingress ports
D. egress ports
Answer: D
Explanation:
QUESTION NO: 94
Answer: D
Explanation:
QUESTION NO: 95
The Adaptive Networking license only activates which two features? (Choose two.)
A. bottleneck detection
B. QoS ingress rate limiting
C. HBA target rate limiting
D. QoS SID/DID traffic prioritization
Answer: B,D
Explanation:
Topic 2, Volume B
QUESTION NO: 96
In the exhibit,
A. 2
B. 3
C. 4
D. 5
Answer: C
Explanation:
QUESTION NO: 97
A. 2
B. 3
C. 5
D. 7
Answer: B
Explanation:
QUESTION NO: 98
which two statements are true regarding FC-FC routing? (Choose two.)
Answer: B,D
Explanation:
QUESTION NO: 99
When using Brocade Network Advisor to manage device sharing with FC-FC routing, which two
statements are true? (Choose two.)
Answer: A,D
Explanation:
You have an FC-FC routed SAN environment and have many servers booting over SAN.
To ensure the routed targets are imported to a routed fabric before the host is online, what should
be used?
Answer: B
Explanation:
You have a Brocade DCX 8510-8 with the default Virtual Fabrics feature enabled. You want to
enable FC-FC routing on this chassis as the backbone.
A. EX_Ports must be configured on the default logical switch in the chassis to connect edge
fabrics.
B. Sharing devices from the backbone fabric to the edge fabrics is supported.
C. The backbone fabric can be expanded to other logical switches in interopmode.
D. A base switch must be created with the routing ports assigned to it.
Answer: D
Explanation:
In the exhibit,
A. 3
B. 5
C. 7
D. 9
Answer: D
Explanation:
In an FC-FC routed fabric, to which fabric element are proxy devices logically connected?
A. base switch
B. front domain
C. logical switch FID 128
Answer: D
Explanation:
In the exhibit,
In the exhibit,
Answer: B
Explanation:
In the exhibit,
Answer: D
Explanation:
Regarding Brocade feature implementation in Fabric OS v7.0, which two statements are true?
(Choose two.)
Answer: A,C
Explanation:
In the exhibit, the server and the storage are communicating in an operational metaSAN.
A. A proxy device representing the server will appear in the backbone fabric.
B. A proxy device representing the storage will appear in the edge fabric A.
C. LSAN zoning for the host and target is configured in the backbone fabric.
D. Edge Fabric A and B have the same Fabric ID.
Answer: B
In the exhibit,
which two long-distance solutions will accomplish FC-FC routing and minimize the impact of failed
connectivity between the Brocade 7800s on the SAN devices at each remote end? (Choose two.)
Answer: A,C
Explanation:
A. LSAN zone names are not case sensitive but need to be the same in each fabric.
B. LSAN zone members do not need to be identical in each of the fabrics.
C. LSAN zones are configured by the administrator in the backbone fabric to allow edge-to-edge
FC Routing.
D. LSAN zone members can be defined by domain/port or the port WWN.
Referring to the exhibit, the front domain connectivity has been verified and is operating as
expected.
When configuring device sharing in this edge-to-edge environment, which two additional
conditions must occur to allow the translate domains to come online? (Choose two.)
Answer: A,B
Explanation:
Answer: A,B,C
Explanation:
When you connect the cable between Switch 1 and Switch 3, as shown in the exhibit, the
connection segments.
Answer: B
Explanation:
Referring to the exhibit, FC-FC routing has been properly configured. The ISL has failed.
Answer: A
Explanation:
As shown in the exhibit, the translate domain is not present in the FC-FC routed fabric. LSAN
definitions have been confirmed.
Answer: B
Explanation:
Referring to the Fabric OS v7.0 FC-FC routed SAN environment shown in the exhibit, Host A is
not able to connect to Storage B.
Given the switch output shown in the exhibit, what is the cause?
Answer: C
Explanation:
This metaSAN is fully operational and all valid LSAN zones have been created.
Answer: D
Explanation:
This metaSAN is fully operational and all valid LSAN zones have been created.
Answer: B
Explanation:
Referring to the exhibit, you need to deploy FC-FC routing across an FCIP link to isolate your two
routed fabrics.
Answer: D
Explanation:
Answer: B
Explanation:
You need to implement FC routing in your SAN. Your backbone fabric will contain a factory default
Brocade 7800 and a Brocade DCX 8510-8 with two FC16-32 blades.
Which two statements enable these devices to form the backbone fabric? (Choose two.)
Answer: A,D
Explanation:
You need to implement FC routing in your SAN. Your backbone fabric will contain a factory default
Brocade 7800 and a Brocade DCX 8510-8 with two FC16-32 blades. Your final configuration will
include VEX_Port connectivity to the edge fabrics.
Which two statements will enable the final configuration? (Choose two.)
Answer: A,D
Explanation:
Your FC-to-FC backbone fabric has two operational links to the same edge fabric. The first link is
an EX_Port and the second link is a VEX_Port. Your implementation requires that both paths are
used to actively carry traffic.
Answer: C
Explanation:
You need to deploy FC-FC routing between two edge fabrics across an FCIP link. Each edge
fabric contains a single Brocade 6510 switch. Your backbone fabric consists of two Brocade
7800s.
A. Configure E_Ports between the 7800s and VE_Ports on each edge fabric connecting to
EX_Ports in the backbone.
B. Configure VE_Ports between the 7800s and VE_Ports on each edge fabric connecting to
VEX_Ports in the backbone.
C. Configure VEX_Ports between the 7800s and E_Ports on each edge fabric connecting to
EX_Ports in the backbone.
D. Configure VE_Ports between the 7800s and E_Ports on each edge fabric connecting to
EX_Ports in the backbone.
Answer: D
Explanation:
You are implementing FC-FC routing and are preparing to configure the FID of the backbone
switch.
A. the switch
B. the EX_Ports on the switch
C. the E_Ports on the switch
D. ACLs on the switch
Answer: A
Explanation:
A. Brocade 7800
B. Brocade 6510
C. Brocade FX8-24
D. Brocade FS8-18
Answer: A,C
Explanation:
You have configured an FCIP tunnel on your streaming backup solution. The performance is not
suitable for the amount of data to be backed up each night.
Which two features would you enable to improve throughput? (Choose two.)
A. encryption
B. IPsec
C. tape pipelining
D. compression
Answer: C,D
Explanation:
You need to implement an FCIP solution with a 1 Gbps FCIP tunnel using copper connections.
Which two Brocade products will provide the solution? (Choose two.)
Answer: B,C
Answer: B
Explanation:
Which two statements about the feature are true? (Choose two.)
Answer: C,D
Explanation:
You have configured an FCIP link between two remote data centers. Adaptive Rate Limiting has
been configured on this link.
When TCP retransmits are detected on the link, what will happen to the committed rate?
Answer: B
Explanation:
You need to provision an additional circuit for an FCIP tunnel between your data centers. The
existing tunnel uses IPsec.
Answer: D
Explanation:
A. 1
B. 2
C. 3
D. 4
Answer: B
Explanation:
ISLs have been created from VE12 to VE16, and VE13 to VE17.
Referring to the exhibit, how many FCIP circuits have been created?
A. 2
B. 3
C. 4
D. 6
Answer: C
Explanation:
Open Systems Tape Pipelining (OSTP) has been configured in the environment shown in the
exhibit.
A. Switch A responds to completed I/Os by automatically sending the next read operation to the
tape device.
B. Switch B responds to completed I/Os by automatically sending the next read operation to the
tape device.
C. Switch A responds to the host with cached data when the host sends the next read command.
D. Switch B responds to the host with cached data when the host sends the next read command.
Answer: B,C
Explanation:
You have deployed Brocade FX8-24 blades. You have decided to set up several FCIP links
between the data centers.
Which three port configurations are available for simultaneous use on each blade? (Choose
three.)
Answer: B,C,E
Explanation:
Your company must migrate data to a new data center 100 km away. You decide to use an FCIP-
shared infrastructure instead of dark fiber.
Answer: A,B
Explanation:
Which distance buffer credit allocation mode would you configure if you do not know the distance
of the link, and want the switch to calculate and select the optimum buffer credits for the port?
A. LE
B. L0
C. LS
D. LD
Answer: D
Explanation:
Which two Brocade Fabric OS v7.0 features must be disabled when configuring a port for distance
using a Time Division Multiplexing (TDM) third-party link that requires ISL R_RDY?
A. TI Zones
B. QoS
C. credit recovery
D. Admin Domain
Answer: B,C
Explanation:
You have allocated the correct number of buffers for your distance and speed on an extended
distance link over dark fiber. However, you notice that there is a latency issue being reported on
the port. The port is repeatedly buffer starved.
What is a common reason for this performance problem over the distance link?
Answer: B
Explanation:
You are experiencing performance issues on your long-distance link and you suspect a buffer-
starvation issue.
A. vc_translation_link_init
B. ISL R_RDY mode
C. QoS
D. credit recovery
Answer: D
Explanation:
When enabling a long distance link connected to a TDM device, which two parameters need to be
in a disabled state for the link to come up? (Choose two.)
Answer: A,C
Explanation:
You are setting up a long-distance link between site A and site B which are 50 km apart. You are
using 16 Gbps ISL ports on each port between the sites.
A. 356
B. 406
C. 426
D. 450
Answer: B
Explanation:
You need to run the Diagnostic Port test on a long distance FC link.
Answer: D
Explanation:
A. The test is supported on the Brocade 6510 with a 8 Gbps optical transceiver.
B. The test is supported on the Brocade DCX 8510-8 with a 8 Gbps optical transceiver.
C. The test is supported on an Brocade DCX 8510-4 with a 10 Gbps FC optical transceiver.
D. The test is supported on the Brocade 6510 with a 16 Gbps optical transceiver.
Answer: C,D
Explanation:
on which two ports can you configure bottleneck detection? (Choose two.)
A. Port 1
Answer: A,B
Explanation:
Your application is using an average frame size of 1024 bytes across your long-distance links.
Answer: B
Explanation:
Your customer told you to configure buffer credit recovery on a Brocade switch in the default
configuration.
Answer: A,D,E
Explanation:
You have configured ports 0-2 on your Brocade 6510 to a distance of 50 km at 16 Gbps. As
shown in the exhibit, additional buffers were allocated to port 2 only.
Answer: C
Explanation:
Your customer asked you to configure two new long distance links without providing the physical
link length. Using portcfglongdistance, you want to determine what will allocate the correct amount
of buffers based on a payload size of 2112 bytes.
A. LD, since it calculates BB credits based on the distance measured during port initialization.
B. LS, since it calculates BB credits based on the distance measured during port initialization.
C. LS, since it calculates a static number of BB credits based only on a user-defined distance
value.
D. LD, since it calculates a static number of BB credits based only on a user-defined distance
value.
Answer: A
Explanation:
You must configure a long distance link to use idle fill words.
Answer: A,C
Explanation:
You were asked to use the portcfgfillword command to configure a long distance link between two
Brocade 6510s.
Answer: B,C
Explanation:
After installing new 16 Gbps switch products, you run the bottleneckmon command. A console
message reports congestion bottlenecks are present on several ports.
How would you resolve this problem without removing legacy devices from the fabric?
Answer: B
Explanation:
You have attached a new Brocade DCX 8510-8 using one ISL to an existing fabric. The new DCX
8510-8 has merged into the fabric, but it is showing several connection errors over the span of a
few hours. You decide to run the D_Port diagnostic test on the ISL from the DCX 8510-8 using
Brocade Network Advisor.
A. The DCX 8510-8 will perform loopback diagnostics only to the port on its own chassis.
B. The DCX 8510-8 will prompt the user for the test parameters to use, and then run inline
diagnostics.
C. The DCX 8510-8 will segment from the existing fabric and all FC communication will be
suspended on that ISL.
D. The DCX 8510-8 will push the port diagnostics to the other switch, then run the loopback
diagnostic on that port.
Answer: C
Explanation:
Referring to the exhibit, which two statements are true? (Choose two.)
Answer: A,D
Explanation:
You have just installed a new Brocade DCX. After connecting the network cable to the active CP,
you run the firmwaredownload command using FTP and it fails repeatedly.
A. Change from the administrator to the user login access level on the switch.
B. Change to the USB stick to download the firmware file.
C. Install a second network cable to the standby CP.
D. Ensure you are uploading a valid NOS file to the DCX chassis.
Answer: B,C
Explanation:
The Frame Viewer feature is able to help diagnose which type of problem in a complex fabric?
Answer: C
Explanation:
You have several fabrics consisting of Brocade 16 Gbps, 8 Gbps, and 4 Gbps products. You
would like a single management product for troubleshooting, monitoring, and management of your
fabrics.
Answer: D
Explanation:
Your fabric is running slow and you want to implement Top Talkers to locate the congestion in the
fabric.
Which two statements are true about Top Talker monitors? (Choose two.)
Answer: B,C
Explanation:
You have an ISL that is oversubscribed. You clear the port statistics and run the porterrshow
command.
Answer: D
Explanation:
You are troubleshooting an ISL issue and you would like to isolate the ISL to diagnose the link
level faults.
A. N_Port
B. VC_link init mode
C. R_RDY mode
D. D_Port
Answer: D
Explanation:
Which three statements about the "supportsave" are true? (Choose three.)
A. The information is saved for the local and the remote CP.
B. The core files and panic dumps remain on the switch after the command has finished.
C. The core files and panic dumps are removed from the switch after the command has finished.
D. The FFDC data are removed after the command has finished.
E. The "supportsave" output is all ASCII.
Answer: A,B,D
Explanation:
On a Brocade 6510, you are using framelog --show to display detailed information about the
discarded frames logged.
A. unroutable
B. unreachable
Answer: D
Explanation:
Answer: A
Explanation:
You observed that one of your Brocade DCX 8510-8s experienced a failover. You logged into the
switch and ran errshow to determine why the failover occurred, but nothing besides the failover
message was displayed.
Answer: B
Explanation:
Traffic isolation zones are configured as shown in the exhibit. The RASLog message has indicated
a potential error. In troubleshooting the command zone --showTIerrors produces the output in the
A. Port 8 on domain 3 is in the same zone with different remote domain 1 ports.
B. Port 8 on domain 1 is in the two zones with different remote domain 3 ports.
C. Port 8 on domain 3 is in the same zone with different remote domain 2 ports.
D. Port 8 on domain 3 is in two zones with different remote domain 1 ports.
Answer: D
Explanation:
An FCIP tunnel between two Brocade 7800s is bouncing online then offline. The service provider
said the link is experiencing errors.
Answer: A
Explanation:
The network administrator is notified of a port login problem occurring between two devices across
an FCIP tunnel. "Supportsaves" were taken on both end switches to determine if the frames were
being dropped on the FC links or by the switch blades. Support has concluded that frames were
not dropped.
Which action determines if the connected FCIP tunnel is dropping the frames?
Answer: A
Explanation:
You are interested in improving the performance from switch 5100 to BES.
Referring to the output shown in the exhibit, which two statements are true? (Choose two.)
Answer: B,D
Explanation:
You have a routed fabric consisting of two edge fabrics connected to the backbone fabric with two
EX_Ports on the backbone fabric running Fabric OS v7.0. The edge switches in each fabric are
Brocade 6510. The trunk master to edge fabric B has failed.
Referring to the exhibit, which two statements are true? (Choose two.)
A. Edge fabric A will segment from edge fabric B briefly while a new trunk master is determined.
B. Edge fabric A will not segment from the backbone fabric.
C. The IFLs to edge fabric A will speed negotiate down to 8 Gbps for bandwidth matching.
D. The IFLs to edge fabric A will continue at 16 Gbps.
Answer: B,D
Explanation:
You have an edge switch trunked to a Brocade 6510 using 8 Gbps IFLs. You use the trunkshow -
perf command to check the trunk ports.
What can you determine from the output shown in the exhibit?
Answer: D
Explanation:
You have an FCIP tunnel/circuit bouncing and are experiencing poor performance. You have
issued the portcmd tperf command.
Answer: C
Explanation:
Answer: B
Explanation:
You are using FC routing to allow a host in the backbone with FID 10 to communicate with the
target in the edge fabric with FID 100. The host is unable to communicate with the target.
Answer: B
Explanation:
You are using FC routing to allow a host in the edge fabric with FID 10 to communicate with the
target in the edge fabric with FID 20. The Backbone FID is 100. The host is unable to
communicate with the target.
Answer: A
Explanation:
You are using FC routing to allow a host in the edge fabric with FID 10 to communicate with the
target in the edge fabric with FID 20. The Backbone FID is 100. The host is unable to
communicate with the target.
Answer: B
Explanation:
Answer: A
Explanation:
Answer: D
Explanation:
A. The corresponding LSAN zone names must match in each of the fabrics.
B. All devices in a single LSAN can only be from two fabrics.
C. You need to use Node WWNs for your devices in LSAN zones.
D. The LSAN zone configuration on FID 2 is incorrect.
Answer: D
Explanation:
You have just connected the switch, whose output is shown in the exhibit, to an existing fabric.
Answer: A
Explanation:
Answer: C
Explanation:
You must configure an FCIP circuit between the devices shown in the exhibit using the addresses
shown. Local subnet connectivity has been verified and functional, but the circuit has failed to
come online.
Answer: D
Explanation:
FC-FC routing is taking a long time to present and set up paths for the proxy devices. Some of the
hosts are timing out.
A. trunkdebug
B. speed tag
C. spinfab
D. R_RDY mode
Answer: B
Explanation:
Answer: A,D
Explanation:
Your customer reports performance problems in their fabric. You exercise a "SuperPing" to isolate
the issue.
A. "SuperPing" requires that all switches in the fabric run Fabric OS v7.0 or later.
B. "SuperPing" tests all ISLs and the internal links included in the paths that route to the
destination.
C. You use fcping without any options.
D. You must use fcping --allpaths.
Answer: B,D
Explanation:
A. IPSec
B. FC router
C. FCIP circuit
Answer: D