Professional Documents
Culture Documents
20341T Pne
20341T Pne
20341T Pne
200
INSTALLATION INSTRUCTIONS
IN-WALL TANK
K-20006T-PNE/K-20006K-PNE/K-20007T-PNE/K-20007K-PNE
K-20008T-PNE/K-20008K-PNE/K-78073T-PNE/K-78073K-PNE
K-78074T-PNE/K-78074K-PNE/K-78075T-PNE/K-78075K-PNE
K-20341T-PNE
GB26730-2011
!
Ordering Information
HYDRO-TOWER 200 PNE IWT 2.6/4L ....................................................................................................................K-20006T-PNE
HYDRO-TOWER 200 PNE IWT 2.6/4L.....................................................................................................................K -20006K-PNE
HYDRO-TOWER 200 PNE IWT 3/4.5L ....................................................................................................................K-20007T-PNE
HYDRO-TOWER 200 PNE IWT 3/4.5L ....................................................................................................................K-20007K-PNE
HYDRO-TOWER 200 PNE IWT 3/6L .......................................................................................................................K-20008T-PNE
HYDRO-TOWER 200 PNE IWT 3/6L .......................................................................................................................K-20008K-PNE
HYDRO-TOWER 200 PNE IWT W/O FRAME 2.6/4L ..............................................................................................K-78073T-PNE
HYDRO-TOWER 200 PNE IWT W/O FRAME 2.6/4L...............................................................................................K -78073K-PNE
HYDRO-TOWER 200 PNE IWT W/O FRAME 3/4.5L ..............................................................................................K-78074T-PNE
HYDRO-TOWER 200 PNE IWT W/O FRAME 3/4.5L ..............................................................................................K-78074K-PNE
HYDRO-TOWER 200 PNE IWT W/O FRAME 3/6L .................................................................................................K-78075T-PNE
HYDRO-TOWER 200 PNE IWT W/O FRAME 3/6L .................................................................................................K-78075K-PNE
PEBBLE Pneumatic In-Wall Tank Faceplate (For Separate Purchase)...................................................................K-20341T-PNE
! Anti flow-backwards !
! Adjustment of inlet water level !
! Adjustment of flushing volume !
! Single/double gear flushing !
! Assemble, disassemble and !
maintenance can be done without
tools.
! Installation of in-wall tank is much easier and nice-looking comparative to that of traditional tank. Meanwhile, the space
layout will be more reasonable due to the application of in-wall tank pipes and connectors.
! The most remarkable advantage of in-wall tank is that the installation will never be limited to certain area, and can be
installed wherever as you wish, which will make the bathroom layout more reasonable and nice-looking, and make good use
of every inch of the bathroom space.
!
!
! Madeofmacromolecularmaterialsthatpreventscorrisonandleaking.
Advanced water tank fitting, which makes possible the adjustment of the water discharge and double flush.
!
Will not affect the structure of the wall and provides excellent sound insulation.
!
Easy installation and time efficient.
!
Donotneedtoprepareanyotherspareparts.
!
Easymaintenanceandservicing.
!
Clean, garbage free, and space saving.
!
!
!
!
!
!
!
!
1288818-T01-A -2-
SPECIFICATIONS
K-20008T-PNE Fullflushingvolume:6L
K-20008K-PNE Halfflushingvolume:3L
K-78075T-PNE 6L
K-78075K-PNE 3L
K-20007T-PNE Fullflushingvolume:4.5L
K-20007K-PNE Halfflushingvolume:3L
K-78074T-PNE 4.5L
K-78074K-PNE 3L
K-20006T-PNE Fullflushingvolume:4L
K-20006K-PNE Halfflushingvolume:2.6L
K-78073T-PNE 4L
Literperflushing K-78073K-PNE 2.6L
Temperature Environmentaltemperature:1°C~55°C,
Watertemperature:1°C~45°C
1°C~55°C
1°C~45°C
RECOMMENDES TOOLS AND MATERIALS
! Open end/adjustable wrenches ! /
! Allen wrench !
! Knife !
! File !
! Hacksaw !
! Masonry !
! Level !
! Screw driver !
! Insulation tape !
! Tape measure !
! Seal tape !
! Bushing !
! Lubricant !
1288818-T01-A -3-
ROUGHING-IN
Reference Value UNIT: mm
K-20006T-PNE/K-20006K-PNE/K-20007T-PNE/K-20007K-PNE/K-20008T-PNE/K-20008K-PNE
Installed with K-20341T-PNE
K-20341T-PNE
Method three:
Method one: Method two: Remote installation
Press from top Remote plate installation of mask
23~72
800
Pinch
plate
4
35
100 2
Method four:
Press from front
205
Finished wall
180 3 90 0.5
230 3 85~93
Finished At least
floor 80mm gap
reserved
80mm
K-78073T-PNE/K-78073K-PNE/K-78074T-PNE/K-78074K-PNE/K-75075T-PNE/K-78075K-PNE
Installed with K-20341T-PNE
K-20341T-PNE
Method three:
Method one: Method two: Remote installation
Press from top Remote plate installation of mask
2
installation area
R1000mm R1000mm
23~72
461 3
134 2 Pinch
322 3
plate
At least
80mm gap
reserved
80mm
1288818-T01-A -4-
Floor Discharge Installation Method
Water Tank
Bracket
There are three methods (A, B and C) for drainage pipe
installation. Loosen the knob "open" on the fixing frame, put Discharge
the drainage pipe into the fixing frame, then adjust and Elbow
tighten the knob "lock". Fill the bottom of the drainage pipe in
the drainage hole .
A Drain outlet 90mm, welding
90mm
A B C Water Tank
Bracket
open
lock Discharge
Elbow
Tank Bracket
Discharge
Fixing Frame
Elbow
Knob
Bottom of the Drainage Pipe
Drainage Hole
C Drain outlet 110mm, welding
110mm
Kohler reserves the right to change marked dimensions without prior notice.
1288818-T01-A -5-
INSTALLATION
Way of Installation
There are two ways to install this product: in-wall tank with
frame & in-wall tank without frame
( )
( )
Cover,Top Cover,Front
Installation For In-wall Tank With Frame
( )
1.
Plug Cover,Top
Supporting Board
Cover,Front
Screw Base
2. Insert the frame screw and screw cap in the holes of fixing
frame, lock the frame screw with nut, then tighten the
Nut
frame screws on the fixing frame with medium Allen key as Frame Screw
shown in illustration A.
Tighten the bolts with medium Allen key as shown in Screw Cap
illustration B, and adjust the height of the adjustable
bracket according to customer's requirements.
Tank Frame
2. A A
Nut
Medium Allen Key
B
Adjustable Bracket
1288818-T01-A -6-
3. Drill four holes with diameter of 10mm and depth of 80mm
with churn drilling as shown, and fill in the holes with bulge Bulge Screw
screw and tighten the screw.
3. 10mm 80mm
Gasket
4. Tighten the hexagonal long screw with medium Allen key Hexagonal Screw
as shown in illustration A.
Tighten the screw of adjustable brackets with medium Loosen
Allen key as shown in illustration B, and tighten the long Level Tighten
screw with spanner.
Spanner
Screw Adjustable Bracket
K-20006K-PNE/K-20008K-PNE
1288818-T01-A -7-
B. Floor Discharge Installation Method
Water Tank
B. Bracket
Discharge
1. There are three methods (A, B and C) for drainage pipe Elbow
installation. Loosen the knob "open" on the fixing frame,
put the drainage pipe into the fixing frame, then adjust and
tighten the knob "lock". Fill the bottom of the drainage pipe
in the drainage hole . A Drain outlet 90mm, welding
90mm
1. A B C
open Water Tank
lock Bracket
Discharge
Elbow
Drainage Pipe
Water Tank
Bracket
Fixing Frame Discharge
Elbow
Knob
Bottom of the Drainage Pipe
Drainage Hole
2. Tighten the long screw into the holes of the tank bracket Inlet Hole
and cover the drainage hole with the big cap, cover the
Tank Bracket
inlet hole with the small cap.
Small Cap
2.
Long Screw
Drainage Hole
Big Cap
3. Connect tap water braided tube on the top of water tank for
water supply as shown.
3.
1.
2.
1288818-T01-A -8-
4. Access Panel Installation Methods: Method one: Method two:
Press from top Remote plate installation
There are four ways to install access panel:
Method one: Press from top
Method two: Remote plate installation: fix four plates with Suggested faceplate
installation area Pinch
screws plate
R1000mm
Method three: Remote installation of mask
23~72
Method four: Press from front: fix four plates with screws
4.
:
Air hose
Method three:
Remote installation Method four:
of mask Press from front
At least
80mm gap
reserved
80mm
Air hose
5.
1)
2) Cut apart the cable of the air hose and pull it out from
the mask. Cable
2)
1288818-T01-A -9-
6. Methods two and three: During remote installation, fix the Cover,Top
cover onto the tank and pull the air hose to the panel. Cover,Front
Reserve access panel at front or top to ensure removal
and installation of cover.
Fix Mask Onto Wall
6. Air hose
Finished
10 Hole through hose wall
10
7. Method four: Cut apart the cable of the air hose. Pull it out Method four:
from the front of the tank and meanwhile reserve the Press from front
access panel. Fix the four plates with screws and then fix
the support board.
Pinch plate Finished wall
Air hose
Note: No direct contact between the faceplate and the tank.
7~20mm thickness recommended for the wall of the
pinch plate.
At least 80mm gap reserved
80mm
7.
7~20mm
Pinch plate
Supporting Pinch plate
Board
Supporting Board Finished wall
Air hose 7~20mm recommended
7~20mm
Screw
Faceplate
1288818-T01-A -10-
C. Installation of P-trap
C.
1. Insert drainage pipe with inner diameter 110mm into Water Tank Bracket
drain elbow and weld.
1. 110mm
Drainage Pipe
2. Tighten the long screw into the holes of the tank bracket Small Cap
and cover the drainage hole with the big cap, cover the
inlet hole with the small cap. Water Inlet
Long Screw
2.
Drainage Hole
Big Cap
Access Panel
3. When finishing the brickwork of the wall, take out the big Mask
and small caps, and eliminate unwanted mask with a sharp
knife, if there is mask.
Note: Reserve access panel at front or top of the tank. Access Panel
3.
Small Cap
Big Cap
D. Installation of Toilet
D.
1288818-T01-A -11-
2. Eliminate unwanted part of the inlet pipe according to the Inlet Pipe
marks of reserved space ,and rasp a smooth surface with
files.
Reserved Space
2.
Drainage Pipe
3.
Inlet Pipe
Drainage Pipe
4. 48mm-58mm 48mm-58mm
Lubricant
5.
Spirit Level
1288818-T01-A -12-
6. Install the reserved lock, gasket, hexagonal nut and
decoration cap onto long screw according to the order
shown in the illustration.
Note: Please refer to the installation instructions of toilet. Long Screw
6.
Reversed Lock
Gasket
Hexagonal Nut
Decoration Cap
Supporting Board
E. Faceplate Installation
Locknut
E.
1. OPEN
2. LOCK
3. Install the big flush air hose and small flush air hose to the
cover. Put the lock on the cover directly on the reversed
lock on supporting board, then push the cover and lock it.
The installation shall begin from bottom to top. Faceplate
Note: Cut the excessive parts of the air hose if necessary and
fix it onto the tank fastener.
Lock
3. Faceplate
Supporting
Board
Fastener
Connect to air hose
1288818-T01-A -13-
4. It is ready to use when connected to water supply after
installation.
Note: Reserve access panel at front or top of the tank in Full Flush
remote installation. Button
Half Flush Button
4.
Cover,Front
1.
Plug Cover,Top
Supporting Board
Cover,Front
Spring
2. h
Nut
h
O10mm 80mm
1288818-T01-A -14-
3. Put the tank onto the fixing bracket as shown in the right
figure and adjust the tank to level . Then tighten screws
Level
with hex-head key.
Tank
Screw
5. Connect tap water braided tube on the top of water tank for
water supply as shown.
5.
1.
2.
Method four: Press from front: fix four plates with screws
Pinch
plate
6.
: Air hose
At least
80mm gap
reserved
80mm
Air hose
1288818-T01-A -15-
7. Method one: Install mask when pressing from top
Cover,Top
1) Remove top plate, then install the mask on the top of the Mask
tank, and tighten the screw to fix the mask to the tank.
Screw
7.
1)
2) Cut apart the cable of the air hose and pull it out from
the rectangle cover.
Cable
2)
8. Methods two and three: During remote installation, fix the Cover,Top
cover onto the tank and pull the air hose to the panel. Cover,Front
Reserve access panel at front or top to ensure removal
and installation of cover.
8. Air hose
Finished
10 Hole through hose wall
10
1288818-T01-A -16-
9. Method four: Cut apart the cable of the air hose. Pull it out Method four:
from the front of the tank and meanwhile reserve the Press from front
access panel. Fix the four plates with screws and then fix Finished wall
the support board. Pinch plate
Air hose
Note: No direct contact between the faceplate and the tank.
7~20mm thickness recommended for the wall of the At least
pinch plate. 80mm gap
reserved
9. 80mm
7~20mm
Faceplate
10. Insert the inlet pipe and drainage pipe into the bowl, and
then adjust the syphon and drainage pipe to a proper
position to be fixed into the bowl. Make sure of the Syphon
positions of syphon and discharge elbow and then
Inlet Pipe
remove the bowl.
10.
1288818-T01-A -17-
11. When finishing the brickwork, eliminate unwanted part of Mask
the mask, the drainage pipe and the inlet pipe, if there is
mask.
Drainage Pipe
12. E
REMOVEANDMAINTENANCEOFTHEOUTLETVALVE
1. Remove the air hoses of the big flush and small flush.
Then remove the faceplate.
1. Faceplate
Faceplate
1288818-T01-A -18-
2. Pay special attention when dismantle supporting board 4
lock nuts, all bolts shall align with "OPEN" mark.
2. OPEN
Locknut
3.
Open
Valve
5. Unscrew the nut of the metal weaved hose and push the
connector of the inlet valve as shown to remove the inlet
valve. Conntector,Quick release
5.
1288818-T01-A -19-
6. Push aside the snap of the toilet detergent box to take the
box out.
6.
Snap
7. Push aside the pivot snaps of the big flush and small flush
towards upper right to make the lever and pivot apart. Hold Snap (Locked)
( )
bracket top by hand and then lift up to unlock the bracket.
Note: Push aside the pivot snaps of the big flush and small
flush towards lower left to fix back the bracket. Lock the snap.
7.
Lever Snap
8.
Fastener
Fastener
9.
Outlet Valve
1288818-T01-A -20-
10. Remove discharge valve as shown and then take valve
out for cleaning or adjusting. Outlet Valve
10.
Outlet Valve
Close corner valve first, then loosen and take out the tighten
nut, and wash the waste on filtration net with clean water.
Then reset the tighten nut to the original position.
A.
Open
Close
Close
Open
A C
Filtration Net
B. Adjustment Switch
Drainage valve
(1)
(2)
1288818-T01-A -21-
C. Adjust Inlet Valve Inlet Valve
C. Floating Box
Floatingboxofinletvalveisblockedbyotherparts. Readjustthepositionofotherpartstoavoid
contactingthefloatingboxwhenitis
functioning.
Nowaterfillsinviainlet
valve Floatingboxofinletvalveisblockbywaste. Washthefloatingboxwithcleanwater.
Theairhoseandfaceplatearewronglyinstalled. Reinstalltheairhose.
Nodrainagewhen
pressingtheheavyand Thepoleandthereversedlockarenotconnected. Reinstallthereversedlockontothepoleof
slightdrainagebutton theoutletvalve.
Toohighortoolowwater Thefloatingboxoftheinletvalveisnotproperly Readjustthewaterlevel.
level adjusted.
Thefloatingboxoftheinletvalveisblockedby Readjustthepositionofotherpartstoavoid
wastes,sothewaterisleakedfromtheoverflow contactingthefloatingboxwhenitis
pipe. functioning.
Leakofthetoiletand Therubbergasketisblockedbywastes. Takeouttheoutletvalveandcleanthe
squat wastes.
A.Nowatersupply. A.Waitforrestorationofwatersupply.
Toiletdoesnotflush
B.Thewatersupplystopisclosed. B.Openthewatersupplystop.
Toiletdoesnotflush
Filterscreenisclogged. Refertowashfiltrationnet.
completely
1288818-T01-A -22-
A. A.
B. B.
1288818-T01-A -23-