Professional Documents
Culture Documents
May-2021-202-Exam Paper
May-2021-202-Exam Paper
SEMESTER:202
1. You have drawing “A” as shown, which modify command of AutoCAD user interface
can be used to obtain drawing “B”?
Rotate Command
Mirror Command
Copy Command
Trim Command
Extend Command
2. Which short / toggle key can be used to turn on a mode of AutoCAD user interface that
helps to draw horizontal and vertical lines?
Status bar
Menu bar
Draw toolbar
Modify toolbar
The object lies between the observer and the plane of projection.
6. Which panel may be accessed for right command to dimension line BC in the figure
show in AutoCAD?
8. How many surfaces can be seen from the top of the object shown?
Seven
Eight
Nine
Ten
Six
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
9. Which option is true for SNAP in AutoCAD user interface?
10. Which one of the following bar / panel is used to set drawing environment?
a) Properties Panel
b) Status bar
c) Annotation Panel
d) Modify Panel
e) Quick Access Tool Bar
11. How many hidden lines will be drawn in the left end elevation of the object shown?
One
Two
Three
Four
Five
12. In orthographic views, what will be the length of horizontal hidden line in elevation of
the object shown in figure?
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
20 mm
22 mm
32 mm
30 mm
29 mm
13. Which panel is used to access multiline text command in AutoCAD user interface?
a) Annotation Panel
b) Draw Panel
c) Clipboard
d) View
e) Modify
14. Which option tells the name of command for symbol is shown?
Copy command
Extend Command
Offset Command
Mirror Command
Move Command
15. What is the name of the component having a set of gears used to change axis of
rotation and spread the engine’s power across the two driven wheels of car?
Differential
Gear Box
Steering Box
Axle Shaft
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
Flywheel
16. Which option describes the clearance volume (Vc) of engine’s cylinder in car?
It is the volume between cylinder head and the piston top surface when the piston is at Bottom
Dead Center (BDC).
It is the volume between the cylinder head and the piston top when the piston is at top dead
center (TDC).
17. Which component of ignition system increases voltage to ignite air fuel mixture?
Battery
Ignition Coil
Distributor
Spark Plugs
18. Which component of exhaust system converts the toxic pollutants in exhaust gases
into less toxic?
Catalytic Convertor
Muffler
Resonator
Tailpipe
Exhaust manifold
19. Which pair of components is not the part of the transmission system?
20. Which option tells the difference between foot brake and hand brake of car?
Foot brakes are always disc brakes but hand brakes are always drum brakes.
Foot brake bypasses the hydraulic part of brake system whereas hand brake use oil as
working fluid.
Foot brake uses a brake fluid to operate whereas hand brake does not uses brake fluid to
operate.
Foot brakes are always drum brakes but hand brakes are always disc brakes.
Hand brakes are always on front wheels whereas foot brakes applies brake only on back
wheels.
It releases chemical energy from fuel and converts it into mechanical energy.
It release chemical energy from fuel and cnverts it into solar energy.
Fuel System
Suspension System
Ignition System
Transmission System
Brake System
23. Which of the following systems reduces force of friction between the cylinder walls and
piston in engine?
Cooling system
Exhaust System
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
Lubricating system
Fuel system
Transmission system
Longitudinal
Transverse
Vertical
Overhead
Angular
The carburetor ignites the air and fuel mixture in combustion chamber at the end of exhaust
stroke.
The exhaust gases leave the cylinder at the end of compression stroke.
The air and fuel mixture is ignited by a spark plug in the combustion chamber at the end of
compression stroke.
The air and fuel mixture is ignited by a spark plug in the combustion chamber at the end of
induction stroke.
Kinetic Energy
Mechanical Energy
Solar Energy
Nuclear Energy
28. Which one of the following options does not tell advantage of Pneumatic system?
It is overload safe.
The whole system has to be shut down in the case of required maintenance.
29. The adjacent sketch is symbol of a pneumatic component. What is the function of that
component?
Reciprocating Cylinder
Intake Manifold
Startup Valve
Logic Valve
Flow control Valve
31. Which of the following equations show the correct conversions between different units
of pressure?
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
a) One (1) bar = 14.5 Psi = 10⁶ N/m² = 0.1 MPa
b) One (1) bar = 14.5 Psi = 100000000 N/m² = 0.1 MPa
c) One (1) bar = 72 Psi = 10⁵ N/m² = 34 MPa
d) One (1) bar = 14.5 Psi = 10⁵N/m² = 0.1 MPa
e) One (1) bar = 102 Psi = 34 N/m² = 0.1 MPa
32. Another description for a Dual Pressure Valve is:
OR gate.
AND gate.
5/2 way valve with selector switch.
Limit valve.
5/2 way pneumatically operated valve.
33. Which of the following options is true for comparison between single acting cylinder
and double acting cylinder?
Single acting cylinder has two ports whereas double acting cylinder has one port.
Double acting cylinder has two ports whereas single acting cylinder has no spring.
Double acting cylinder has no return spring whereas single acting cylinder has two ports.
Single acting cylinder can be fully operated by 5/2way valve whereas double acting cylinder
cannot be fully operated by a 5/2 way valve.
Single acting cylinder has return spring whereas double acting cylinder has no return spring.
34. For the symbol shown here, which option shows the right description of pneumatic
valve?
36. Which valve is used to get automatic return movement of cylinder and is activated by
cylinder-touch?
Impulse Valve
Limit Valve
Flow Control Valve
AND gate Valve
OR gate Valve
37. Which statement shows right description for Pilot valve?
Expanded air.
Air with pressure above atmospheric pressure.
Air with pressure below atmospheric pressure
Air with pressure equal to atmospheric pressure
Oil as working fluid.
39. In the EV3 brick, which one of the following components are connected to EV3 brick
through the output ports?
Large motor
Ultrasonic Sensor
Touch Sensor
42. The minimum object distance an Ultrasonic sensor can detect is:
3 cm or 250 inches
3 cm or 1 inch
3cm or 99 inches
250 cm or 99 inch
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
Switch block
Loop block
Control block
Wait block
Move tank block is ON with full power of both motors for 100 seconds.
Move Tank bock is ON for 25 seconds with full power of both motors.
Move Tank block is used with half power of right motor and full power of left motor.
45. Where are the building blocks found in EV3 programming environment?
Hardware area
Programming page.
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
Programming Content editor
46. Which option tells the speed and stall torque of large motor respectively?
47. Which one of the following colors cannot be detected by a color sensor when it is in
color mode?
Yellow
Blue
Brown
Red
Orange
48. Which of the following sensors used in Lab is not a digital sensor?
Color Sensor
Ultrasonic Sensor
Gyro Sensor
Touch Sensor
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202
None of above
49. What is the name and function of component of which symbol is shown?
50. Which block is not found under Action Tab of EV3 programming environment?
Sound block
Loop Block
FINAL EXAM-PREP ENGINEERING TECHNOLOGY-PYP004
SEMESTER:202