Professional Documents
Culture Documents
Mbe 300
Mbe 300
Installation Manual
UPS Network
Management
Card 2
AP9630, AP9631
DMP IM 990-3404.book Page ii Monday, March 11, 2013 9:05 AM
Contents
Preliminary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features 3
Related documents 3
Inventory 3
Disclaimer 4
Language Packs 4
Installation in a UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
How to install the card for different UPS models 5
Step 1: Turn off power (Smart-UPS) 5
Step 2: Install the Network Management Card 5
Step 3: Restore power to the card slot 6
Step 4: Configure the Network Management Card 6
Quick Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overview 9
TCP/IP configuration methods 9
Device IP Configuration Utility 10
DHCP and BOOTP configuration 10
Local access to the command line interface 12
Remote access to the command line interface 13
Command line interface 14
.INI file utility 14
Installation Manual i
DMP IM 990-3404.book Page ii Monday, March 11, 2013 9:05 AM
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ii Installation Manual
DMP IM 990-3404.book Page 1 Monday, March 11, 2013 9:05 AM
Smart-UPS.
1. Turn off the equipment that connects to the UPS.
2. Disconnect the UPS from its AC input source.
3. Press the OFF button on the UPS for approximately five seconds to turn off
the DC (battery) power.
Expansion chassis. Make sure that the Expansion Chassis or Triple Expansion
Chassis is disconnected from any power source:
1. Disconnect the chassis cable from the UPS.
2. If the chassis uses an AC adapter (AP9505), disconnect that adapter from
the chassis.
Installation Manual 1
DMP IM 990-3404.book Page 2 Monday, March 11, 2013 9:05 AM
2 Installation Manual
DMP IM 990-3404.book Page 3 Monday, March 11, 2013 9:05 AM
Preliminary Information
Features
Related documents
The Network Management Card Utility CD contains the following documentation:
• UPS Network Management Card 2 User’s Guide
• Network Management Card Upgrade Utilities
• Security Handbook
• PowerNet® Management Information Base (MIB) Reference Guide
Inventory
The Network Management Card package includes the following items:
• This Installation Manual
• UPS Network Management Card 2
• UPS Network Management Card 2 Utility CD
• Serial configuration cable (940-0299)
• Temperature sensor (AP9335T)—AP9631 Network Management Card only
• Network Management Card quality assurance test slip
• Declaration of Conformity
• Warranty registration form
The quality assurance test slip contains the MAC address that you may
need when performing the procedures in “Device IP Configuration
Utility” on page 10. You can also find the MAC address on the back of
your UPS.
Installation Manual 3
DMP IM 990-3404.book Page 4 Monday, March 11, 2013 9:05 AM
Disclaimer
Schneider Electric is not responsible for damage sustained during reshipment of this
product.
The Network Management Card (NMC) is sensitive to static
electricity. When handling the NMC, touch only the end plate while
using one or more of these electrostatic-discharge devices (ESDs):
wrist straps, heel straps, toe straps, or conductive shoes.
Please recycle
The shipping materials are recyclable. Save them for later use, or
dispose of them appropriately.
Language Packs
If the language you want to use with the NMC Web interface is not
available, you should download a language pack. See “Adding and
Changing Language Packs” in the User’s Guide. (Language packs are
not available for all UPS devices).
4 Installation Manual
DMP IM 990-3404.book Page 5 Monday, March 11, 2013 9:05 AM
Installation in a UPS
How to install the card for different UPS models
You can install the UPS Network Management Card (NMC) in a card slot in a
Smart-UPS, Symmetra UPS, Galaxy 300, Galaxy 3500, or Galaxy 7000.
You cannot install this NMC in a Symmetra PX 250 or Symmetra PX
500 UPS.
In a Symmetra UPS that uses more than one management product, you must install
the management products in the correct order for them to operate properly.
For the location of the UPS card slot, see the UPS documentation.
Installation Manual 5
DMP IM 990-3404.book Page 6 Monday, March 11, 2013 9:05 AM
60a
mph 04
6 Installation Manual
DMP IM 990-3404.book Page 7 Monday, March 11, 2013 9:05 AM
Installation Manual 7
DMP IM 990-3404.book Page 8 Monday, March 11, 2013 9:05 AM
8 Installation Manual
DMP IM 990-3404.book Page 9 Monday, March 11, 2013 9:05 AM
Quick Configuration
Overview
Disregard the procedures described in this chapter if you have
StruxureWare Central as part of your system. See the documentation for
your StruxureWare device for more information.
You must configure the following TCP/IP settings before the UPS Network
Management Card (NMC) can operate on a network:
• IP address of the NMC
• Subnet mask
• Default gateway
If a default gateway is unavailable, use the IP address of a computer that
is located on the same subnet as the NMC and that is usually running.
The NMC uses the default gateway to test the network when traffic is
very light.
Do not use the loopback address (127.0.0.1) as the default gateway
address for the NMC. It disables the card and requires you to reset TCP/
IP settings to their defaults using a local serial login.
See “Watchdog Features” in the “Introduction” of the NMC User’s
Guide for more information about the watchdog role of the default
gateway.
Installation Manual 9
DMP IM 990-3404.book Page 10 Monday, March 11, 2013 9:05 AM
10 Installation Manual
DMP IM 990-3404.book Page 11 Monday, March 11, 2013 9:05 AM
Installation Manual 11
DMP IM 990-3404.book Page 12 Monday, March 11, 2013 9:05 AM
12 Installation Manual
DMP IM 990-3404.book Page 13 Monday, March 11, 2013 9:05 AM
1. Use the MAC address of the Network Management Card in the ARP
command to define the IP address.
Note: Look for the MAC address on the bottom of the Network
Management Card or on the Quality Assurance slip included in the package.
For example, to define 156.205.14.141 as the IP address of a Network
Management Card with 00 c0 b7 63 9f 67 as its MAC address, use one of
the following commands:
– Windows command format:
arp -s 156.205.14.141 00-c0-b7-63-9f-67
– LINUX command format:
arp -s 156.205.14.141 00:c0:b7:63:9f:67
2. Use Ping with a size of 113 bytes to assign the IP address defined by the
ARP command. For the IP address defined in step 1, use one of the
following commands:
– Windows command format:
ping 156.205.14.141 -l 113
– LINUX command format:
ping 156.205.14.141 -s 113
3. Use Telnet to access the Network Management Card at its newly assigned
IP address. For example:
telnet 156.205.14.141
4. Use apc for both user name and password.
Installation Manual 13
DMP IM 990-3404.book Page 14 Monday, March 11, 2013 9:05 AM
14 Installation Manual
DMP IM 990-3404.book Page 15 Monday, March 11, 2013 9:05 AM
Installation Manual 15
DMP IM 990-3404.book Page 16 Monday, March 11, 2013 9:05 AM
16 Installation Manual
DMP IM 990-3404.book Page 17 Monday, March 11, 2013 9:05 AM
For more information about the interfaces, see the User’s Guide.
Web interface
Use Microsoft Internet Explorer® (IE) 7.x or higher (on Windows operating systems
only) or Mozilla® Firefox® 3.0.6 or higher (on all operating systems) to access the
Web interface of the Network Management Card. Other commonly available
browsers may work but have not been fully tested by APC.
You can use either of the following protocols when you use the Web interface:
• The HTTP protocol (enabled by default), which provides authentication by
user name and password but no encryption.
• The HTTPS protocol, which provides extra security through Secure Socket
Layer (SSL); encrypts user names, passwords, and data being transmitted;
and authenticates Network Management Cards by means of digital
certificates.
To access the Web interface and configure the security of your device on the
network:
1. Address the Network Management Card by its IP address (or its DNS name,
if a DNS name is configured).
2. Enter the user name and password (by default, apc and apc for an
Administrator).
3. To enable or disable the HTTP or HTTPS protocol, use the NMC Web
interface.
See the Security Handbook, available on the Network Management
Card Utility CD or from the APC Web site, www.apc.com, for more
information on selecting and configuring network security.
Installation Manual 17
DMP IM 990-3404.book Page 18 Monday, March 11, 2013 9:05 AM
18 Installation Manual
DMP IM 990-3404.book Page 19 Monday, March 11, 2013 9:05 AM
Installation Manual 19
DMP IM 990-3404.book Page 20 Monday, March 11, 2013 9:05 AM
20 Installation Manual
DMP IM 990-3404.book Page 21 Monday, March 11, 2013 9:05 AM
Installation Manual 21
DMP IM 990-3404.book Page 22 Monday, March 11, 2013 9:05 AM
1 2 3
1 2 3 Monitoring Port Power
mph0461
Sensor Zones Probes
GND 1 2 3 4 1 2
Management Port USB U niv ers al I /O U niv ers al I /O Network
Status 24 VDC
To UPS – – +
Config Reset
10/100
AP9612TH Environmental Monitoring Card AP9608 Out-of-Band Management Card Smart Slot A P963 1 Network Management Card 2
Status
If the NMC is pre-installed in the UPS, refer instead to “When an NMC has been
pre-installed.” on page 23
22 Installation Manual
DMP IM 990-3404.book Page 23 Monday, March 11, 2013 9:05 AM
For Symmetra models with 4, 3, or 2 slots, install each card, starting with the lowest
priority (as listed in the table on page 21) in the lowest numbered slot. Use the
following illustrations to determine model-specific slot numbering.
• When 4 slots are available, arranged in a horizontal row, the
lowest-numbered slot is at the right.
When an NMC has been pre-installed. For Symmetra UPS models that are
shipped with a Network Management Card already installed (such as Symmetra RM
models), the UPS itself may have only one remaining card slot available. Referring
to the table on page 1, install the lowest priority card in the UPS and use one or more
expansion chassis for any other cards, as described beginning on page 2.
To use an Out-of-Band Management Card, install it in the highest-numbered slot of
the expansion chassis farthest from the UPS.
Installation Manual 23
DMP IM 990-3404.book Page 24 Monday, March 11, 2013 9:05 AM
24 Installation Manual
DMP IM 990-3404.book Page 25 Monday, March 11, 2013 9:05 AM
Specifications
Physical
Environmental
Temperature
Operating 0 to 45°C (32 to 113°F)
Storage -5 to 45°C (23 to 113°F)
Regulatory compliance
Installation Manual 25
DMP IM 990-3404.book Page 26 Monday, March 11, 2013 9:05 AM
26 Installation Manual
DMP IM 990-3404.book Page 27 Monday, March 11, 2013 9:05 AM
Installation Manual 27
DMP IM 990-3404.book Page 28 Monday, March 11, 2013 9:05 AM
28 Installation Manual
DMP IM 990-3404.book Page 29 Monday, March 11, 2013 9:05 AM
USA—FCC
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with this
user manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference. The user
will bear sole responsibility for correcting such interference.
Canada—ICES
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Japan—VCCI
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is
used in a domestic environment, radio disturbance may occur, in which case, the
user may be required to take corrective actions.
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準
に基づくクラス A 情報技術装置です。この装置を家庭環境で使用すると、電波
妨害を引き起こすことがあります。この場合には、使用者が適切な対策を講ず
るように要求されることがあります。
Taiwan—BSMI
警告使用者 :
這是甲類的資訊產品 , 在居住的
環境中使用時 , 可能會造成射頻
干擾 , 在這種情況下 , 使用者會
被要求採取某些適當的對策。
DMP IM 990-3404.book Page 30 Monday, March 11, 2013 9:05 AM
© 2013 by Schneider Electric. All rights reserved. StruxureWare, Symmetra, MGE, Galaxy, and Smart-
UPS are owned by Schneider Electric Industries S.A.S., American Power Conversion Corporation, or
their affiliated companies. All other trademarks are property of their respective owners.
990-3404C-001 3/2013