Professional Documents
Culture Documents
Saic M 1031
Saic M 1031
00 30-Jun-16
EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.
LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.
SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
SAUDI ARAMCO USE ONLY
SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
A Receiving Inspection
The Final Inspection Shipping release is available along with the Pre-
Schedule Q,
Engineered Building at the time of receipt at the job site. (Note: Pre-
A1 Attach III, Sec.
Engineering Building is Inspection Level 3 as per SAEP-1151, Appendix
3.23
A)
The materials furnished shall include the roofing, siding, anchor bolts,
flashing and trim, leveling plates, doors, windows, hardware, fasteners, 12-SAMSS-014
A2
sealants, and any other component parts for the metal buildings as Sec. 4.1
specified in the order and as required to make a complete system.
All materials shall be new, free of defects and meet or exceed the physical 12-SAMSS-014
A3
requirements of the design and fabrication process. Sec. 6
Unless indicated in the Purchase Order, the vendor shall provide either
single sheet or sandwich type roof and wall panels based on the required
12-SAMSS-014
A4 maximum heat transmission coefficient and required internal design
Sec. 6.5
temperature. The choice of panels is subject to prior written approval of
the buyer.
12-SAMSS-014
A5 Roof panels shall be ribbed to provide adequate rigidity.
Sec. 6.5.1.b
Single Sheet Roof and Wall Panels shall be made of a minimum 0.5 mm
12-SAMSS-014
(26 gage) thick galvanized or aluminum-zinc alloy-coated steel sheet.
A6 Sec. 6.5.1.a &
Roof panels for buildings in coastal areas, or as specified in the purchase
Sec. 6.5.3.b
order shall be made of a minimum 0.7 mm thickness aluminum sheet.
Single Sheet Roof and Walls Panels shall be insulated to provide the 12-SAMSS-014
A7 maximum heat transmission coefficient (U) as specified in the Purchase Sec. 6.5.1.g &
Order. Sec. 6.5.3.f
Sandwich Roof/ Wall Panels shall be self contained, factory assembled 12-SAMSS-014
A9 foam plastic insulated units having a nominal covering width of not less Sec. 6.5.2.a &
than 900 mm (3 ft nominal) unless approved otherwise by Saudi Aramco. Sec. 6.5.4.a
EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.
LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.
SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
SAUDI ARAMCO USE ONLY
SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
Sandwich Roof/ Wall Panels interior face sheet shall be minimum 0.5 mm 12-SAMSS-014
A11 (26 gage) thick galvanized or aluminum-zinc alloy-coated sheet steel and Sec. 6.5.2.c &
shall be formed into a plane surface. Sec. 6.5.4.c
12-SAMSS-014
Sandwich Roof/ Wall Panels Foam plastic insulation shall have a flame
A12 Sec. 6.5.2.d &
spread rating of 25 or less.
Sec. 6.5.4.f
Roof and Wall Fasteners shall be hex head carbon steel screws
assembled with an EPDM washer and mechanically zinc coating in
12-SAMSS-014
A13 accordance with ASTM B695, Class 50. However, in coastal areas an
Sec. 6.6
austenitic (300 series) stainless steel fasteners shall be used. Fastener
heads shall be coated the same color as the panels.
REMARKS:
REFERENCE DOCUMENTS:
1- 12-SAMSS-014 -- Pre-Engineered Metal Buildings, 16 Jan. 2014