Professional Documents
Culture Documents
Epson WF C5790 WF C5790A WF C5710 ET 8700 WF C5210 WF C5290 WF C5290A Service Manuals 301 350
Epson WF C5790 WF C5790A WF C5710 ET 8700 WF C5210 WF C5290 WF C5290A Service Manuals 301 350
Plate
Double-sided tape CRCM FFC Sheet Double-sided tape
1. Peel off the CRCM FFC. 1. Remove the two screws (S6: ), and remove the Plate.
2. Peel off the CRCR FFC Sheet. When installing the Ink Supply Tube to the RIPS Unit, make sure to tighten the
screws using a torque driver with the specified torque.
Screw tightening torque: 0.59±0.01Nm
Relay Board
CN55
CN10
CN22 CN54
CN11
CN30
CN31
CN2
1. Remove the two screws (S4: ), and remove the Guide Cover in the direction of the arrow. 1. Disconnect the cables from the connectors (CN2, CN10, CN11, CN12, CN22, CN30,
CN31, CN54, CN55) on the Relay Board.
2. Release the cables from the five tabs on the Frame Base.
Rear Top
Printer
Hole
RIPS Unit
Top
Joint
No. Screw Type
S4 C.B.P-TITE-SCREW-3x10-F.ZN-3C
3. Pull the Decompression Pump Cable out from the hole of the Frame Base, and release the As ink may leak in the following steps, prepare a waste cloth or the like in advance.
ferrite core of the decompression pump cable from the Frame Base.
4. Remove the eight screws (S4: ) that secure the RIPS Unit.
5. Remove the Joint from the Ink Supply Tube.
RIPS Unit
A13 B13 C13
Ink Supply Unit
Left Joint of ink tube D13
PF scale
Bottom of joint
When lifting the main body, you wear gloves. Because there is a danger of cutting hands with 1. Release the cover open sensor cable from the slit and hook on the Ink Supply Housing.
the sharp metal enclosed by red circles, 2. Remove the four screws (S11: ), then remove the Ink Supply Unit from the Ink Supply
Lift carefully so as not to touch the PF scale on the left side of the main body. If you touch the Housing.
PF scale, clean it with a clean cloth.
6. Grasp the handle of the yellow square part on the left and right sides of the main body and Route the cables of the Ink Supply Unit on the frame of the Ink Supply Unit.
lift it vertically.
Make sure all the ink tubes are properly secured at the joints. If not, insert the rib on
the tube into the joint in place and secure the tube properly by turning it
counterclockwise.
Upper Plate
1. Remove the two screws (S5: ), and remove the Pressing Plate. 1. Disconnect the Ink Sensor FFC from the connector (CN1) on the Ink Sensor YMCBk.
2. Remove the two screws (S5: ), and remove the Upper Plate.
A16 B16
Decompression Pump Assy CSIC Board FFC
CSIC Board
FFC (Cyan)
Tube
Decompression
Pump
CN5
CN4
Guide (Cable)
Ferrite core
1. Pull the Decompression Pump Tube from the Joint. 1. Disconnect the CSIC Board FFC from the connectors on the CSIC Board.
2. Release the decompression pump tube and decompression pump cable from the guides. 2. Pull the CSIC Board FFC from the ferrite core.
3. Remove the three screws (S15: ), then remove the Decompression Pump. 3. Disconnect the Ink Sensor FFC from the connectors on the Ink Sensor YMCBk.
CSIC Board
FFC (Black)
CN3
CSIC Board
FFC (Yellow)
CN2 Ink Sensor YMCBk
CSIC Board
FFC (Magenta)
CN4
CN5
CSIC Board
FFC (Cyan)
Secure the CSIC Board FFC on the position shown above with double-sided tape. 1. Disconnect the Cartridge Detection FFC from the connector on the Ink Sensor YMCBk.
Top
Connector
Tab Tab
CSIC Board
FFC
OK NG
Hook
1. Disconnect the FFC from the connector while pushing the CSIC Sensor Board. 1. Slide the CSIC Board to disengage the two hooks of the sensor from the two grooves of the
2. Push the dowel of the Duct Pump Assy using tweezers or similar tool, and release it from Duct Pump Assy.
the positioning hole on the CSIC Sensor Board. Refer to the figure above and check the installation surface of the CSIC Board.
3. Slide the CSIC Sensor Board in the direction of the arrow to remove it.
Set the CSIC Sensor Board under tab of tabs of the Duct Pump Assy.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
DISASSEMBLY FLOWCHART
Start
Start
A4 B4 C4 Housing Right
D4 E4 (→P. 312)
A5 B5 C5 Housing Left
D5 E5 (→P. 313)
A6 B6 C6 Housing Upper
D6 E6 (→P. 313)
A7 B7 C7 ADF/SCN Unit
D7 E7 (→P. 314)
A1 B1 C1 A2 B2 C2
Rear Cover (Back) ASF Front Cover
D1 E1 D2 E2
1. Remove the four screws (S4: ), then remove the Rear Cover (Back). 1. Remove the four screws (S4: ) that secure the ASF Front Cover.
Attach the two dowels of the Rear Cover (Back) to the positioning holes on the 2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
Housing Left and Housing Right. the back.
A3 B3 C3 A4 B4 C4
Ink Eject Cover Housing Right
D3 E3 D4 E4
Rear
Hook
Housing Right
Hooks
1. Disengage the hook, and remove the Ink Eject Cover. 1. Open the ADF/SCN Unit.
2. Remove the four screws (S4: ) that secure the Housing Right.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then
remove the Housing Right.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply
Unit.
A5 B5 C5 A6 B6 C6
Housing Left Housing Upper
D5 E5 D6 E6
Rear
Housing
Hooks Upper
Housing Left
Hooks Top
1. Open the ADF/SCN Unit. 1. Remove the six screws (S4: ), then remove the Housing Upper.
2. Remove the three screws (S4: ) that secure the Housing Left.
3. Lift the Housing Left to release the two hooks on the front side of the Housing Left.
4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Upper and the Ink Supply Unit.
ADF/SCN Unit
A7 B7 C7
ADF/SCN Unit
D7 E7
Open Close
ADF/SCN Unit 45 °
Connector Lock
CN801 Double-sided tape
CN612
CN606
CN601
C H E C K When disconnecting the CISM FFC (CN601) from this connector, make sure to 3. Open the ADF/SCN Unit.
P O IN T
unlock the connector lock beforehand. 4. Remove the two screws (S4: ), then remove the ADF/SCN Unit in the direction of the
arrow.
1. Disconnect the cables and FFCs from following connectors on the Main Board.
Before screwing the ADF/SCN Unit, make sure the hinges are properly attached in place.
If the ADF/SCN Unit is opened when the hinges are NOT secured, the unit may be damaged.
• CN601 • CN606 • CN612 • CN801
2. Peel off the acetate tape, then remove the grounding cable.
B8 C8
Hinge Assy Open the ADF Unit
D8 E8
C H E C K When removing the Main Board Assy on the way to the target part, remove the Hinge 1. Push the ADF lock lever in the direction of the arrow, and open the ADF Unit.
P O IN T
Assy (Left) only.
1. Remove the each screw (S4: ), and remove the two Hinge Assy.
C9
Document Mat ADF Front Cover
D9
Dowels
Document Mat
ADF Base
Holes
Holes
1. Remove the Document Mat. 1. Remove the two screws (S4: ) that secure the ADF Front Cover.
2. Disengage two hooks, then remove the ADF Front Cover in the direction of the arrow.
Attach the four dowels to the holes of the ADF Base.
Bottom
Rear ADF Cover Hook
Bottom
ADF Right
Cover
1. Remove the two screws (S4: ), then remove the ADF Lower Cover. 3. Remove the screw (S4: ) that secures the Rear ADF Cover.
2. Remove the two screws (S4: ), then remove the ADF Right Cover. 4. Disengage the hook of the Rear ADF Cover, then remove the Rear ADF Cover.
Attach the two dowels of the Rear ADF Cover to the holes on the ADF Base.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
ADF Paper Feed Roller
Unit A --- --- ---
DISASSEMBLY FLOWCHART
Start
Start
A4 B4 C4 Housing Right
D4 E4 F4 (→P. 321)
A5 B5 C5 Housing Left
D5 E5 F5 (→P. 322)
A6 B6 C6 Housing Upper
D6 E6 F6 (→P. 322)
A7 B7 C7 ADF/SCN Unit
D7 E7 F7 (→P. 323)
A1 B1 C1 A2 B2 C2
Rear Cover (Back) ASF Front Cover
D1 E1 F1 D2 E2 F2
1. Remove the four screws (S4: ), then remove the Rear Cover (Back). 1. Remove the four screws (S4: ) that secure the ASF Front Cover.
Attach the two dowels of the Rear Cover (Back) to the positioning holes on the 2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
Housing Left and Housing Right. the back.
A3 B3 C3 A4 B4 C4
Ink Eject Cover Housing Right
D3 E3 F3 D4 E4 F4
Rear
Hook
Housing Right
Hooks
1. Disengage the hook, and remove the Ink Eject Cover. 1. Open the ADF/SCN Unit.
2. Remove the four screws (S4: ) that secure the Housing Right.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then
remove the Housing Right.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply
Unit.
A5 B5 C5 A6 B6 C6
Housing Left Housing Upper
D5 E5 F5 D6 E6 F6
Rear
Housing
Hooks Upper
Housing Left
Hooks Top
1. Open the ADF/SCN Unit. 1. Remove the six screws (S4: ), then remove the Housing Upper.
2. Remove the three screws (S4: ) that secure the Housing Left.
3. Lift the Housing Left to release the two hooks on the front side of the Housing Left.
4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Upper and the Ink Supply Unit.
ADF/SCN Unit
A7 B7 C7
ADF/SCN Unit
D7 E7 F7
Open Close
ADF/SCN Unit 45 °
Connector Lock
CN801 Double-sided tape
CN612
CN606
CN601
C H E C K When disconnecting the CISM FFC (CN601) from this connector, make sure to 3. Open the ADF/SCN Unit.
P O IN T
unlock the connector lock beforehand. 4. Remove the two screws (S4: ), then remove the ADF/SCN Unit in the direction of the
arrow.
1. Disconnect the cables and FFCs from following connectors on the Main Board.
Before screwing the ADF/SCN Unit, make sure the hinges are properly attached in place.
If the ADF/SCN Unit is opened when the hinges are NOT secured, the unit may be damaged.
• CN601 • CN606 • CN612 • CN801
2. Peel off the acetate tape, then remove the grounding cable.
A8 B7 C7 B9
ADF Paper Feed Roller Unit ADF Document Support
D7 E7 F7
Dowel
(White)
Dowel
Dowel
Dowel
1. Open the ADF Paper Feed Roller Unit. 1. Disengage the two dowels of the ADF Document Support while bending it, then remove the
2. Disengage the two dowels, one each on the left and right sides, while pressing the dowel ADF Document Support.
(white) with a flathead screwdriver, and then remove the ADF Paper Feed Roller Unit.
C9
ADF Pad Assy ADF Roller Spring
E9 D9 F9
Hook Hook
ADF Sub
Cover
Hooks
Dowels
1. Disengage two hooks of the ADF Separate Pad. 1. Remove the two screws (S4: ) that secure the ADF Upper Paper Guide.
2. Disengage two dowels of the ADF Separate Pad, then remove the ADF Separate Pad. 2. Disengage two hooks, and remove the ADF Upper Paper Guide from the ADF Cover and
ADF Sub Cover.
3. Remove the screw (S4: ), then remove the Fixing Plate.
4. Pull the Paper Feed Roller Shaft in the direction of the arrow. 1. Remove the ADF Separate Spring.
Set the groove the Paper Feed Roller Shaft on the bearing of the ADF Upper Paper Set the leg of the ADF Separate Spring under the tab on the ADF Base.
Guide.
LD Frame Assy
F10
Stopper
1. Lift the LD Frame Assy to release the stopper of the LD Frame Assy from the ADF Upper
Paper Guide, then remove the LD Frame Assy.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
DISASSEMBLY FLOWCHART
Start
Start C H E C K As for the procedure indicated by , refer to 6.2.4.4
P O IN T Housing (WF-C5200 Series) (2) (p. 254) in the case
of the WF-C5200 Series, and remove the parts from the
Preparation for EEPROM Data Copy Rear Back Cover to the Housing Top.
Dissembling (Back up) (→P. 564) The procedure indicated by is applicable only in the
WF-C5700 Series/ET-8700.
A1 B1 C1 Rear Cover (Back) Implement the procedure indicated by when
(→P. 330) replacing the Main Board Assy. See Initial settings (p.
D1 E1 F1
565) and carry out EEPROM Data Copy (Backup)
beforehand and EEPROM Data Copy (Load) after
A2 B2 C2 ASF Front Cover replacement.
D2 E2 F2 (→P. 330)
Hinge Lower Cover Wireless Lan Module Main Board After EEPROM Data Copy
F9 (→P. 338) F15 (→P. 343) F16 (→P. 344) assembling (Restore) (→P. 564)
A1 B1 C1 A2 B2 C2
Rear Cover (Back) ASF Front Cover
D1 E1 F1 D2 E2 F2
1. Remove the four screws (S4: ), then remove the Rear Cover (Back). 1. Remove the four screws (S4: ) that secure the ASF Front Cover.
Attach the two dowels of the Rear Cover (Back) to the positioning holes on the 2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
Housing Left and Housing Right. the back.
A3 B3 C3 A4
Housing Left Wireless Lan Module
D3 E3 F3
Rear
CRCM FFC
CRCM FFC Sheet
Double-sided
tape
Double-sided
Hooks tape
Housing Left
Main Board
Assy
Hooks
CN31
No. Screw Type
S4 Tab Wireless Lan Module
C.B.P-TITE-SCREW-3x10-F.ZN-3C
1. Open the ADF/SCN Unit. 1. Peel off the CRCM FFC from the CRCM FFC Sheet.
2. Remove the three screws (S4: ) that secure the Housing Left. 2. Peel off the CRCM FFC Sheet.
3. Lift the Housing Left to release the two hooks on the front side of the Housing Left. 3. Disconnect the Wireless Lan Module from the connector (CN31) on the Main Board Assy.
4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Upper and the Ink Supply Unit.
FFC
PDL Board Assy
CN102
Shield Plate
1. Disconnect the FFC from the connector (CN102) on the PDL Board Assy. 3. Remove the two screws (S5: ), then remove the PDL Board Assy from the Shield Plate.
2. Remove the screw (S5: ), then remove the PDL Board Assy.
Fax Assy
C4
Fax Assy
Acetate tape
Shield Plate
CN1
Fax Assy
Fax FFC
Double-sided tape
Fax Assy
Acetate tape
1. Peel off the Fax FFC from the Fax Assy. 4. Remove the three screws (S5: ) that secure the Shield Plate.
2. Remove the three screws (S5: ), and slide the Fax Assy in the direction of the arrow. 5. Peel off a piece of acetate tape, and remove the Shield Plate.
3. Peel off a piece of acetate tape, then remove the Fax Assy. 6. Disconnect the FFC from the connector (CN1) on the Fax Assy.
1. Remove the two screws (S4: ), then remove the USB Interface Board. 1. Slide the Holder in the direction of the arrow.
2. Raise the holder, then remove the SD Memory.
Rear
Hook
Housing Right
Hooks
1. Disengage the hook, and remove the Ink Eject Cover. 1. Open the ADF/SCN Unit.
2. Remove the four screws (S4: ) that secure the Housing Right.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then
remove the Housing Right.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply
Unit.
Open Close
Housing
Upper
Connector Lock
CN801 Double-sided tape
Top CN612
CN606
CN601
1. Remove the six screws (S4: ), then remove the Housing Upper. C H E C K When disconnecting the CISM FFC (CN601) from this connector, make sure to
P O IN T
unlock the connector lock beforehand.
1. Disconnect the cables and FFCs from following connectors on the Main Board.
ADF/SCN Unit
Hinge Assy
F8
ADF/SCN Unit 45 °
3. Open the ADF/SCN Unit. C H E C K When removing the Main Board Assy on the way to the target part, remove the Hinge
P O IN T
4. Remove the two screws (S4: ), then remove the ADF/SCN Unit in the direction of the Assy (Left) only.
arrow.
1. Remove the each screw (S4: ), and remove the two Hinge Assy.
Before screwing the ADF/SCN Unit, make sure the hinges are properly attached in place.
If the ADF/SCN Unit is opened when the hinges are NOT secured, the unit may be damaged.
C H E C K When removing the Main Board Assy on the way to the target part, remove the Hinge 1. Release the all cable from the Cable Guide.
P O IN T
Assy (Left) only. 2. Remove the two screws (S4: ), and remove the Cable Guide.
1. Remove the each three screws (S4: ), and remove the two Hinge Lower Cover.
Cable Guide
Guides PS Cable
CR Scale
Main Frame
Guide Hook
Route the PS cable through the two guides and hook on the Cable Guide. 1. Remove the Extension Spring 11.11 from the CR Scale.
Route the solenoid cable through the five hooks ( ) on the Cable Guide. 2. Remove the Extension Spring 11.11 from the Main Frame.
Route the rear ASF sensor cable and photo interrupter cable through the three hooks ( ) on
the Cable Guide.
Route the ASF motor cable through the guide on the Cable Guide.
CR Unit CR Scale
1. At the full side, remove the CR Scale from hook on the frame. 1. Remove the two screws (S4: , S5: ), then remove the PS Ground Plate.
2. Pull the CR Scale out from the CR Encoder Sensor.
3. At the home side, turn the CR Scale 90 degrees upward, and remove it from the hook on the
frame.
Attach the CR Scale with the marking on the bottom right corner.
Open
CN33
1. Peel off the CRCM FFC. C H E C K When disconnecting the Panel FFC (CN42), make sure to unlock the connector lock
P O IN T
2. Peel off the CRCM FFC Sheet. beforehand.
3. Disconnect the following connectors from the board. (* are WF-C5700 Series/ET-8700
only)
Clamps
Hook
PE sensor cable
Main Board Assy
Ferrite core Clamp Relay FFC
Fax FFC
4. Peel off the Fax FFC from the Shield Plate, and Pull the Fax FFC out from the ferrite core. 8. Remove the following screws that secure the Main Board Assy.
(WF-C5700 Series/ET-8700 only) WF-C5700 Series/ET-8700: x9 (S4: x4, S5: x2, S10: x1, S5: x2)
5. Release the PE sensor cable from the clamp. WF-C5200 Series: x7 (S4: x4, S5: x2, S10: x1)
6. Peel off the Relay FFC from the Shield Plate. In the next step, be careful not to damage the PF Scale.
7. Release the CR motor cable from two clamps.
9. Disengage hook of the Main Board Assy from the hole of the CR Guide Frame, then
remove the Main Board Assy upward.
CRCM FFC
Main Board Assy CRCM FFC Sheet
Double-sided
CN52 tape
Double-sided
tape
Main Board
PF Encoder FFC Assy
Double-sided tape
CN31
Secure the PF Encoder FFC with double-sided tape as shown above. 1. Peel off the CRCM FFC from the CRCM FFC Sheet.
2. Peel off the CRCM FFC Sheet.
3. Disconnect the Wireless Lan Module from the connector (CN31) on the Main Board Assy.
Main Board
F16
1. Remove the seven screws (S5: ), then remove the MB Shield Plate Upper.
2. Remove the Main Board from the MB Shield Plate Lower.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
DISASSEMBLY FLOWCHART
Start
Start
A3 B3 Housing Left
C3 (→P. 348)
B5 Housing Right
C5 (→P. 350)
B6 Housing Upper
C6 (→P. 351)
A1 B1 A2 B2
Rear Cover (Back) ASF Front Cover
C1 C2
1. Remove the four screws (S4: ), then remove the Rear Cover (Back). 1. Remove the four screws (S4: ) that secure the ASF Front Cover.
Attach the two dowels of the Rear Cover (Back) to the positioning holes on the 2. Remove the ASF Front Cover upward while slightly bending the Rear Cover (Back) toward
Housing Left and Housing Right. the back.
A3 B3 A4
Housing Left Relay Board Assy
C3
Rear
CRCM FFC
CRCM FFC Sheet
Double-sided tape
Hooks Double-sided tape
Housing Left
Hooks
1. Open the ADF/SCN Unit. 1. Peel off the CRCM FFC from the CRCM FFC Sheet.
2. Remove the three screws (S4: ) that secure the Housing Left. 2. Peel off the CRCM FFC Sheet.
3. Lift the Housing Left to release the two hooks on the front side of the Housing Left.
4. Disengage two hooks on the rear side of the Housing Left, and remove the Housing Left.
Insert the eight tabs on the Housing Left to the positioning hokes of the Housing
Upper and the Ink Supply Unit.
Grounding cable
Relay Board
Shield Plate
3. Disconnect the cables and FFCs from all connectors on the Relay Board Assy. 6. Remove the four screws (S5: ), and remove the Relay Board from the Shield Plate.
4. Remove the grounding cable from the Frame.
5. Remove the four screws (S4: x2, S5: x2), then remove the Relay Board Assy.
B4 B5
Ink Eject Cover Housing Right
C4 C5
Rear
Hook
Housing Right
Hooks
1. Disengage the hook, and remove the Ink Eject Cover. 1. Open the ADF/SCN Unit.
2. Remove the four screws (S4: ) that secure the Housing Right.
3. Lift the Housing Right to release the two hooks on the front side of the Housing Right, then
remove the Housing Right.
Insert the four tabs of the Housing Right to the positioning holes on the Ink Supply
Unit.