Professional Documents
Culture Documents
BL Theraja Mistakes and Corrections. NTS
BL Theraja Mistakes and Corrections. NTS
Chapter#7
Q.42:
Polarity of a dc generator can be reversed by:
A. Increasing field current
B. Reversing field current
C. Reversing the direction of rotation
D. Reversing field current and also the direction of rotation
Q.48:
The number of armature parallel paths in a 12 pole dc generator provided with triplex lap
winding will be:
A. 6
B. 12
C. 24
D. 36
Q.173:
In a dc motor iron losses occur in:
A. the field
B. the armature
C. the yoke
D. none of these
Q.217:
Which one of the following statements for a dc machine which is provided with interpoles
windings (IW) as well as compensating winding (CW) is correct?
A. Both IW and CW connected in series with the armature winding
Chapter#8
Q.13:
A transformer has negative voltage regulation when its load power factor is:
A. zero
B. unity
C. leading
D. lagging
Q.114:
In a transformer the tappings are generally provided on:
A. primary side
B. secondary side
C. low voltage side
D. high voltage side
Q.17:
Main advantage of PMMC instrument is:
A. high torque weight ratio providing high accuracy
B. uniform scale
C. possibility of using a single instrument for many different current and voltage
ranges by use of shunts and multipliers
D. capability of measuring both ac and dc quantities
Q.82:
Rectifier instruments indicate?
A. RMS Value
B. Average Value
C. Peak Value
D. DC Value
Q.94:
An electrical measuring instrument has sensitivity of 1000Ω/volt. On 100 volt scale, this
instrument will have internal resistance of:
A. 10Ω
B. 104 Ω
C. 105 Ω
D. 1000Ω
Q.97:
Difference between the indicated value and the true value of a quantity is known as:
A. Gross error
B. Absolute error
C. Dynamic error
D. Relative error
Q.101:
Precision measurement of resistances is generally carried out by:
A. Potentiometer method
B. CRO method
C. Voltmeter-ammeter method
D. Bridge method
COMPILED BY CH ANEES IRFAN BL THERAJA MISTAKES
Q.238:
Which of the following instruments will have the same calibration on both a.c. and d.c.?
A. Electrodynamometer type
B. Moving iron type
C. Moving coil type
D. Induction type
Q.240:
Meggar is an instrument for:
A. Measuring current
B. Measuring voltage
C. Testing insulation
D. Measuring power
Q.241:
The instrument whose deflection is given by the expression ------------------------------
Is known as:
A. Electrodynamic type
B. Repulsion type
C. Electrostatic type
D. Attraction type
Q.242:
Which of the following error does not result in moving iron instrument with DC and AC?
A. Stray magnetic field error
B. Hysteresis error
C. Eddy current error
D. Temperature error
Q.313:
"Creep" in energy meters can be prevented by:
A. Using extra turns of the voltage coil
B. Having two holes on opposite sides of the disc
C. Using a stronger brake magnet
D. Using steel laminations of high permeability
Q.17:
The function of guard ring transmission lines is:
A. To reduce the transmission losses
B. To reduce the earth capacitance of the lowest unit
C. To increase the earth capacitance of the lowest unit
D. None of these
Q.49:
Which of the following circuit breakers takes minimum time for installation?
A. Bulk oil circuit breaker
B. Minimum oil circuit breaker
C. Air blast circuit breaker
D. SF6 circuit breaker
Q.89:
Energy produced by fission reaction uranium having mass of atom m and velocity of light c
is:
A. mc
B. 1/2m2 c
Confusion here
C. mc2
D. 1/2mc2
Q.137:
Conductors used in high voltage transmission lines are stranded to:
A. Make it easy to handle
B. Reduce the cost
C. Increase its conductivity
D. Increase its tensile strength
Q.164:
Temperature increase produces which of the following effect of a transmission line?
A. Tension of the conductor and its sag increase
B. Tension of the conductor and its sag decrease
C. Tension of the conductor decreases and its sag increases
D. Tension of the conductor increases and its sag decreases
Q.69:
For a lumped inductive load, with increase in supply frequency:
A. P and Q increase
B. P increases ,Q decreases
C. P decreases, Q increases
D. P and Q decrease
Q.94:
The convergence characteristics of the Netwon-Rophson method for solving the load flow problem
is:
A. Quadratic
B. Linear
C. Geometric
D. Cubic
Chapter #16
Q.56:
The band width of a control system may be increased by:
A. Phase lead compensator
B. Phase lag compensator
C. Phase lag-lead compensator
D. None of these
Q.59:
Lead-lag compensation is needed for:
A. Transient response improvement
B. Steady state response improvement
C. Both transient and steady state response improvement
D. None of these
Questions:
The fact as to how closely the instrument reading follows the measured variables is called
the____.
a. Sensitivity
b. Fidelity
c. Precision
d. Accuracy
A transformer transforms:
A. Frequency
B. Voltage
C. Current
D. Power
A. In one direction
B. In both directions
C. Above rated speed
D. Below rated speed
2: The primary reason for the low power factor is due to the installation of
A. DC motors
B. Synchronous motors
C. Induction motors
D. Commutator motors
A. Lead Compensation
B. Lag Compensation
C. Lag-Lead Compensation
D. None
A. Lead Compensation
B. Lag Compensation
C. Lag-Lead Compensation
D. None
Which one of the following can not be treated as an amplifier in control system?
A. DC Generator
B. DC Motor
C. Amplidyne
D. Metadyne
P/S=cos(theta)
S=300/0.6 =500KVA
P=500*1 for unity power factor 500kw
500-300=200Kw.
A. Terminal ends
B. Collector rings
C. Commutator
D. None of above
B. Mass
C.Energy
D.Momentum
The frequency range over which response of the system is within acceptable units is called the
system:
a) Band width
b) Modulation frequency
c) Demodulation frequency
d) Carrier frequency
0
180°✓
90
Logic gates
Registers
The square law of photo detector gives current, this current is proportional to _____ of combined
optical field.
Square✓
square root
Digital Voltmeter
meter with needle
*A*
Commutator✓
winding
Shunt Generator
Compound Generator
Low resistance
Low reluctance
High resistance
High reluctance
GOOD Luck!