Professional Documents
Culture Documents
Dea 202e 3 PDF
Dea 202e 3 PDF
Dea 202e 3 PDF
202E3
I CENTRALE DI COMANDO ISTRUZIONI D’ USO E MANUTENZIONE
19 FCA1 opening limit switch input motor 1 (N.C.) TLAV Work time adjustment trimmer. Both motors stop,both in opening
Stops the movement of motor 1 during opening and closing,after this time is passed.
20 FCA2 opening limit switch input motor 2 (N.C.) In case limit switches are installed, work time have to be set for
Stops the movement of motor 2 during opening some seconds more than the effective time, necessary for the travel
21 FCC1 closing limit switch input motor 1 (N.C.) for the motors.
Stops the movement of motor 1 during closing
22 FCC2 closing limit switch input motor 2 (N.C.) TSFAS Closing wing delay adjustment trimmer.
Stops the movement of motor 2 during closing In opening the delay is fixed : 2 sec.
23 FOTO photocell input item.104/105 (N.C.)
During closing reverses the movement,during opening POWER ADJUSTMENT
(if active) stops the movement. 202E3 has a device which allows the electrical adjustment of the power of
24 APRE open/close input (N.O.) the motors by acting on the trimmers “spunto” and “forza”
may work in step-by-step mode or inversion mode
25 STOP block input (N.C.) SPUNTO It adjusts the starting torque at the beginning of the move-
Always stops the movement of both wings. ment,eliminating therefore eventual problems due to inertia
26 PED. Pedestrian opening input (N.O.) or mechanical friction. (turn clockwise to increase the power,
causes the opening only of motor 1 counterclockwise to decrease it)
WARNING:All unused N.C. must be short-circuited towards the common fo FORZA It adjusts the power of the motor during the movement.
the inputs. (turn clockwise to increase the power, counterclockwise to
decrease it)
27 Antenna ground
28 Antenna signal It is anyway compulsory to respect carefully the power limit values specified
J6 Radioreceiver plug by local regulations, for the country where the installation is made, using
eventually the necessary safety devices.
DIAGNOSTIC LEDS
202E3 control panel has a series of leds signalling the status of the inputs,
placed each one in front of its respective terminal.
In particular for the N.C. inputs (fca1, fca2, fcc1, fcc2, foto e blocco) the re-
spective leds are normally alight and they turn off when one of the above
inputs activates. N.O. inputs(open and pedestrian open) instead, leds are
202E3
normally off and turn on when one of the above mentioned inputs activates.
fig. 1
INNESTO RICEVENTE RG 58
INSERTION RADIORECEPTEUR
CONEXION RECEPTOR RADIO 28
RADIO RECEIVER PLUG ANTENNA
27 ANTENNE
ANTENA
ANTENNA
DEA 202 E3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
START PEDONALE
3 X 1 mm²
3 X 1 mm²
F OUVERTURE PIETONS
APERTURA PEATONAL
PED. N.O.
2 X 1,5mm² PEDESTRIAN OPEN
2 X 0,5 mm²
N
4 X 0,5 mm²
4 X 0,5 mm²
START/APRE
ALIMENTAZIONE 230Vac 50 Hz START/OUVRE
ALIMENTATION 230Vac 50Hz APRE N.O. START/ABRE
SUMINISTRO ELECTRICO 230Vac 50Hz
START/OPEN
POWER SUPPLY INPUT 230Vac 50Hz
2 X 1 mm² M1 M2 BLOCCO
BLOCAGE
STOP N.C. BLOQUE
STOP
LAMPEGGIANTE 230Vac max40W FINECORSA APERURA MOTORE 1
N.C. FCA1 BUTÉE DE FIN DE COURSE EN OUVERTURE MOTEUR 1
CLIGNOTEUR 230Vac max40W
LAMPARA INTERMITENTE 230Vac max40W FIN DE CARRERA ABERTURA MOTOR 1
FLASHING LIGHT 230Vac max40W MOTOR 1 OPENING LIMIT SWITCH
SPIA CANCELLO APERTO 24Vac max 200mA N.C. FCC1 FINECORSA CHIUSURA MOTORE 1
VOYANT PORTAIL OUVERTE 24Vac max 200mA BUTÉE DE FIN DE COURSE EN FERMETURE MOTEUR 1
INDICADOR LUMINOSO PUERTA ABIERTA 24Vac max 200mA FIN DE CARRERA CIERRE MOTOR 1
OPEN GATE WARNING LIGHT 24Vac max 200mA MOTOR 1 CLOSING LIMIT SWITCH
ATTENZIONE: DEA SYSTEM ricorda tuttavia che la scelta ,la disposizione e l’installazione di 24Vac FOTOCELLULA art. 104 / 105
tutti i dispositivi e materiali che compongono l’intera automazione deve avvenire in ottempe- MAX200 mA PHOTOCELLULE art. 104 / 105
4
ranza alle normative vigenti nel paese in cui si effettua l’installazione. FOTOCELLULA art. 104 / 105
2
N.C.
ATTENTION: DEA SYSTEM vous rappelle toutefois que le choix, la disposition et l’installation POHOTOCELL item 104 /105
3
1
de tous les dispositifs et de tous les matériels qui font partie de l’automation complète doivent
2
être exécutés conformément aux réglementations en vigueur dans le pays où l’installation 2 X 0,5 mm²
sera mise en place.
1