Professional Documents
Culture Documents
RS74R5101SLTL SVC Manual PDF
RS74R5101SLTL SVC Manual PDF
REFRIGERATOR CONTENTS
1. PRECAUTIONS (SAFETY WARNINGS)················· 4
2. PRODUCT SPECIFICATIONS································ 7
4. TROUBLESHOOTING·········································44
5. PCB DIAGRAM····················································86
6. WIRING DIAGRAM·············································89
7. BLOCK DIAGRAM················································ 91
RS74R5*** RS71R5***
8. MODEL CODE TABLE········································· 92
RS65R5*** RS62R5***
RS64R5*** RS61R5***
WARNING
All rights reserved. This service guide may not be reproduced in whole or as a
part in any form whatsoever without the written permission of the SAMSUNG
ELECTRONICS Company.
Contents
1. PRECAUTIONS (SAFETY WARNINGS).......................................................................................... 4
2. PRODUCT SPECIFICATIONS..........................................................................................................7
2-1. Introduction of Main Function..............................................................................................................7
2-2. Model Specification............................................................................................................................... 8
2-3. Basic Specification...............................................................................................................................12
2-4. Dimensions (mm/inch)........................................................................................................................15
2-5. Optional Material Specification.........................................................................................................16
4. TROUBLESHOOTING.................................................................................................................. 44
4-1. Using the control panel...................................................................................................................... 44
4-3. Adjust the leveling feet and door height......................................................................................... 49
4-4. Function for failure diagnosis........................................................................................................... 56
4-5. Diagnostic method according to the trouble symptom(Flow Chart)..........................................75
5. PCB DIAGRAM............................................................................................................................. 86
5-1. PBA Layout with part position........................................................................................................... 86
5-2. Connector Layout with part position (Main Board)....................................................................... 87
6. WIRING DIAGRAM...................................................................................................................... 89
6-1. Model : 2 Door, Dispenser (In-Door Ice Maker) RS74R5***, RS65R5***, RS64R5***............. 89
6-2. Model : 2 Door, Basic RS71R5***, RS62R5***, RS61R5*** ........................................................90
7. BLOCK DIAGRAM.........................................................................................................................91
7-1. DISPENSER + INDOOR I/M + PLUMBING...........................................................................................91
● Unplug the appliance before the changing or repairing the electric parts.
● Use rated electronic Control equipment.
➝ Make sure to check out ModeL name, Rated voltage, Rated current,
Operation Temp, etc.
● Upon repair, make sure that harnesses are not to be water-penetrated and
are bundled tight.
➝ Should not be detached by a certain amount of external force.
● Upon repair, completely remove dust or other foreign substances from
housing, harness, connector, etc.
➝ To prevent fire by tracking, short, etc.
● Check out whether water has penetrated into the electronic Control system.
➝ If there is any kind of trace, take necessary measures such as related
component change, insulation tapping, etc.
● After repair, check out the assembled state of parts.
➝ It should be the same as the previous state.
● Check out the surrounding conditions.
➝ Change the location, if the fridge is located at humid, wet places or the
installed state is unstable.
● In order to reduce the risk of electric shock the appliance must be properly
grounded.
● Do not allow consumers to overload a certain outlet.
● Check out whether the power cord or the outlet is broken, squeezed,
chopped off or heatdeformed.
➝ Repair or replace the defective power cord/outlet immediately.
➝ Make sure the power cord is not punctuated or stomped down.
● Do not allow consumers to keep food frayed or place bottles in the Freezer Room.
● Do not allow consumers to repair the fridge by themselves.
● Do not allow consumers to keep things except for food.
➝ Pharmaceutical, Chemical substances : These are not possible to be fine-
Controlled with a consumer fridge.
➝ Flammable material (alcohol, benzene, ether, LPG, etc) : possibility of
explosion.
4
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Read all instructions before repairing the product and follow the instructions in order to prevent danger or
property damage.
CAUTION/WARNING SYMBOLS
DISPLAYED SYMBOLS
means “Prohibited”.
Indicates that a
Warning danger of death
or serious injury
means “Do not disassemble”.
exists.
means “No contact”.
Ra
comp ted
onen
ts
Unplug
On repair, remove completely dust or other After repair, check the assembled state Check if there is any trace indicating the
things of housing parts, harness parts, and of components. permeation of water.
check parts. • It must be in the same assembled state when • If there is that kind of trace, change the related
• Cleaning may prevent the possible fire by tracking compared with the state before disassembly. components or do the necessary treatment such as
or short. taping using the insulating tape.
Earth
5
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Do not allow users to plug several Do not allow users to disassemble, Do not allow users to bend the power
appliances into the same power repair or alter. cord with excessive force or do not
receptable. • It may cause fire or abnormal operation have the power cord pressed by heavy
• May cause abnormal generation of heat or which leads to injury. article.
fire. • May cause fire.
Prohibited Do not
disassemble
Do not allow users to store articles on Do not allow users to install the In order to reduce the risk of electric
the product. refrigerator in the wet place or the shock the appliance must be
• Opening or closing the door may cause things place where water splashes. properly grounded.
to fall down, with may inflict a wound. • Deterioration of insulation of electric parts
may cause electric shock or fire.
Prohibited Earth
6
This document cannot be used without Samsung's authorization
Precautions(Safety
2. PRODUCT SPECIFICATIONS
Warnings)
Large Capacity
• The Samsung Side by side Refrigerator has a very spacious interior with a huge
Capacity. Thinner wall with its special high-urethane insulation technology
and . So there’s plenty of room in the drawers and shelves of the fridge and
freezer to store your weekly grocery shopping, including items of various
shapes or sizes.
And it’s much easier to keep everything neatly and efficiently organized.
So you can quickly find and take out the things you need whenever you need
them.
LED Lighting
• This space-saving LED fixture illuminates every corner of the fridge, so things
are easier to find. Also LED emits less heat than conventional bulb lighting,
affecting less damage to the temperature management.
7
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
• Multi Airflow
Provides even cooling throughout the refrigerator to maintain optimal temperatures to keep food
fresh.
• LED Lighting
See everything in a new light with LED lighting.
8
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
08
04
05
01
02 07
06
03
09
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
10 Wine rack *
NOTE
The design of the egg container may differ with the model.
9
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
10
08
04
05
01
09
07
02
03 06
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
10 Wine rack *
NOTE
The design of the egg container may differ with the model.
10
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
04
05
01
08 09
07
02
03 06
01 Freezer shelves 02 Multipurpose freezer bin 03 Dried food and meat storage drawer
10 Wine rack *
NOTE
The design of the egg container may differ with the model.
11
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Items Specification
RS74R5*** RS71R5***
RS65R5**5
Model RS65R5*** RS62R5*** RS61R5**5
RS64R5**5
RS64R5*** RS61R5***
Image
12
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Items Specification
RS74R5*** RS71R5***
RS65R5**5
Model RS65R5*** RS62R5*** RS61R5**5
RS64R5**5
RS64R5*** RS61R5***
Strong (°C) 0 3
Cold
THERMISTOR
(R-SENSOR) Intermediate (°C) 1.5 4.5
502AT
Weak (°C) 5 8
Initial defrosting cycle
(simultaneous defrosting 6 hours ± 10 minutes
Defrosting Cycle
of F and R)
Components for defrosting
13
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Items Specification
RS74R5*** RS71R5***
RS65R5**5
Model RS65R5*** RS62R5*** RS61R5**5
RS64R5**5
RS64R5*** RS61R5***
Defrosting
Power supplying during
heater in freezing AC 230V, 300W or AC 120V, 300W
freezing compartment defrosting
compartment
Defrosting heater in Power supplying during
-
cold compartment cold compartment defrosting
Home bar heater Ambient humidity sensor
-
(cold compartment) interlocking
Icemaker heater -
AC 230V, 6W or
Dispenser heater -
AC 120V, 6W
Water pipe heater DC12V, 6W -
Water tank heater DC12V, 6W -
Damper heater Kept tumed on - -
Bimetal for preventing overheating of BIMETAL THERMOSTAT - ON : 40℃, OFF : 60℃
defrosting heater in freezing compartment THERMO FUSE - CUT OFF : 109~110℃
Bimetal for preventing overheating of
-
defrosting heater in cold compartment
Type -
Electric Component
14
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
908mm (Cabinet)
846.2 mm
716mm
10.5mm 354.5 mm
765.5 mm
387mm 513mm
912mm (W. Cover Hinge)
0˚~165˚ 0˚~170˚
564 mm
1736.2 mm
716mm
1780
1744
1725
1715
55mm
15
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
For Plumbing
FILTER-WATER DA29-10105J 1
Model
16
This document cannot be used without Samsung's authorization
3-1. PRECAUTION
- NEED TOOL
Hexagon wrench
Use for adjust Door Hinge Ref Up.
(4mm diameter)
17
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-2. Interior-Fridge
Do not put the shelf on the place where wine rack is assembled. If the shelf is put on the
wine rack place, it may cause collision between the shelf and door bin when the door is
CAUTION
closed.
Shelf
Wine Rack
Drawer
cover
18
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. R
emove the inlet cover.
(Remove side hook 2ea)
R-Compartment
Duct & Eva Cover
19
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1. R
emove a deodorizer cover using
tools.
2. R
emove a screw
Multi Cover
(Fridge)
3. R
emove the Multi Cover from
the cabinet.Pull the Cover in the
direction of the front.
20
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Assembly
Remove the Clip and input the Hose.
Water Filter
■ Disassembly
Remove the Hose by puching the Collet.
Be sure to flush the dispenser thoroughly (approx. 6 to 7 minutes), otherwise water may
CAUTION drip from the dispenser. This means that there is still air in the line.
21
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-6. Cover-Display
Cover-Display
22
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Pull out GUIDE ICE(white one) from Assy Case Ice Route.
(Push L&R hooks like right picture.)
Assy Case Ice Route Remove 2 screws on Assy Case Ice Route.
23
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Assembly
Assembling housing of Assy Case Ice Route
Upper 2 Rib have to match with inside Hook
and Screw assembling.
ASSY GUIDE
ICE ROUTE
24
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Disassembly
1. P
ut both fingers in the upper of lever.
Pull and remover the lever slowly.
■ Assembly
2. P
ut the lever with adjusting to rectangle
block slowly.
25
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-9. Interior-Freezer
Drawer
Cover
26
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Evap Cover
(Freezer)
2. R
emove the Evap Cover from
the cabinet.Pull the Cover in the
direction of the front.
27
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1. R
emove Evap Cover first.
3. R
emove the Housing connector.
(2ea)
28
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Door
29
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
Door Be careful not to pinch the water tubing
and the wire harness on the door.Lift up
the door straight in upper direction until
the water hose is eliminated from lower
hinge.Do not pull the door forward to
remove it. It cause injury of water hose
and tubing.
30
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Door
31
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
• T
he Water Line must be fully inserted
to the center of transparent coupler
(Type A) or the line (Type B) to prevent
water leakage from the dispenser.
• Check that it holds the line firmly.
Reassembly
doors
• T
he cover hose must be fully covered
water hose. (Make the cover hose fit to
end of the fitting)
• B
ottom hook must fix the cover hose
to prevent loosen the hose line.
32
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
3-13. Evaporator
Figure
Part Name Description
Freezer Fridge
33
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
34
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
4. Cutting seal.
35
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
36
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. Remove 1 screw.
3. Remove 1 screw.
CAUTION
Cautions for R-600a : Environment-friendly gas (R-600a) is used as refrigerant at this refrigerator, which is
combustible gas though in volume kept small. If gas is leaked by serious damage to the refrigerator during
transportation, installation and operation may cause fire or burn when spark makes contact with leaked
gas.
37
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Ice Bucket
Disassemble the Ice Bucket Assy by holding
Assy
the handle and pulling up
The bottom part slightly.
※indoor only
※indoor only
Disconnect the housing connectors by gently
pulling.
Assy Case
Auger Motor
(assemble)
38
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Assy Ice
Maker
Unscrew the 4 screws.
※indoor only
39
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. Disassembly 2 screws.
Water tank
40
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
2. Disassembly 2 screws.
Water tank
※ indoor
Housing
3. Disconnect the housing and Pull out the
Hose.
41
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Water tank
Housing
4. Disconnect the housing and Pull out the
Hose.
42
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED Lamp
(Fridge)
3. Assemble the new lamp in the
case to be replaced and connect
it to the top housing.
43
This document cannot be used without Samsung's authorization
4. TROUBLESHOOTING Warnings)
Precautions(Safety
3Door : FlexZone/Dispenser
01 Fridge/ Power Cool (3 sec) 02 FlexZone / Vacation(3sec) 03 Freezer / Power Freezer (3sec)
44
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Fridge The Fridge button can be used to set the fridge temperature, or to activate/
deactivate Power Cool.
You can manually adjust the cooling temperature for the fridge. Keep pressing
Fridge to select a desired temperature between 1 °C and 7 °C.
Power Cool Power Cool speeds up the cooling process at maximum fan speed.
This is useful to quickly cool food that spoils quickly, or after the door is left open
for some time. The fridge keeps running at full speed for several hours and then
returns to the previous temperature.
Press and hold Fridge for 3 seconds.
NOTE
It is strongly recommended to empty the fridge compartment and make sure the
door is closed.
45
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
NOTE
Using Power Freeze increases power consumption. Make sure you turn it
off and return to the previous temperature if you do not intend to use it.
NOTE
• I f the ice maker is turned off, it will turn on if you press and hold the ice
lever for more than 5 seconds.
• After tuning off the ice maker by inside cabinet control panel, this
function doesn't work for 1 minute.
Filter Reset (3 sec) After about 6 months (approximately 300 gallons) of using the original
water filter, the Filter indicator turns red to remind you that the filter
needs to be replaced. If this happens, replace the filter, and press and
hold Filter Reset for 3 seconds. The filter indicator will be reset, and the
Filter indicator turns off.
NOTE
Some regional areas have relatively large amounts of lime contained in
the water. This may reduce the life cycle of the filter. In these areas, you
will have to replace the water filter more often than specified above.
46
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
05 Door Alarm
Door Alarm If the door is left open for more than 2 minutes, an alarm will sound and
the alarm indicator will blink. You can toggle the alarm on and off by
pressing Door Alarm. The alarm is enabled by factory default.
If the door is left open for 5 minutes, internal lights (in the fridge, freezer)
will blink for 10seconds and then turn on. This will be repeated every
minute for 5 minutes. This is to alert hearing-impaired users that a door is
open and it is normal.
06 Lock (3 sec)
Lock To prevent accidental setting changes, press and hold Lock for 3 seconds.
The main panel will be disabled and the Lock indicator will turn on.
When Control Lock is on, the indicator blinks if any button on the main
panel is pressed.
If you press and hold the button again for more than 3 seconds, Control
Lock will be deactivated. However, control Lock will be reactivated if no
button is pressed within 1 minute.
NOTE
Control Lock on the main panel does not affect the dispenser.
The dispenser operated independently and so does the dispenser lever.
To lock the dispenser and the dispenser lever, use the Dispenser Lock
function.
07 Sabbath Mode
Sabbath Mode The Sabbath mode stays active for 85 hours once it is activated.
After that, it will be deactivated automatically.
• T
o activate Sabbath Mode, press and hold Door Alarm and Lock
simultaneously for 5 seconds. When the refrigerator is in Sabbath mode,
the buttons, the display, and the room lamps do not function. The
refrigerator and freezer, however, continue to cool.
• T
o deactivate Sabbath Mode, press and hold Door Alarm and Lock
simultaneously again for 5 seconds.
NOTE
If the refrigerator powers off and restarts, the Sabbath mode remains
active. To end Sabbath Mode, you must deactivate it as described above.
47
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
When dispenser lock is on, the indicator blinks if any button on the
dispenser panel is pressed or the dispenser lever is pressed.
NOTE
The Lock on the dispenser panel does not affect the controls on the
main panel. To lock the main panel, use the Control Lock function on
the main panel.
02 Cubed Ice
Cubed Ice Press Cubed Ice to dispense cubed ice.
The corresponding indicator turns on.
03 Crushed Ice
Crushed Ice Press Crushed Ice to dispense crushed ice.
The corresponding indicator turns on.
48
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• The refrigerator must be levelled on a flat, solid floor. Failing to do so can cause damage to the
refrigerator or physical injury.
• Levelling must be performed with an empty refrigerator. Make sure no food items remain inside the
refrigerator.
• For safety reasons, adjust the front side a little higher than the rear side.
The refrigerator can be levelled using the front legs that have a special screw (leveller) for levelling
purposes. Use a flat-head screwdriver for levelling.
49
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1. O
pen the door to adjust, and locate the two nuts
(A) and (B) on the front bottom of the door.
50
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• M
ake sure you connect the coupler to the cold water tap. Connection to the hot water tap may cause the
water filter to be clogged and fail to operate normally.
• T
he warranty for your refrigerator does not cover the water line installation. The water line installation
will be performed at your own costs unless the installation fee is included in the retailer’s price.
• S
amsung takes no responsibility for the water line installation. If water leaks occur, contact the installer
of the water line.
• T
he water line must be repaired by a qualified professional. If you encounter a water leak, contact a local
Samsung service centre or the installer of the water line.
51
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• T
he water line must be connected by a qualified technician.
• T
he warranty for your refrigerator does not cover the water line installation. The water line installation
will be performed at your own costs unless the installation fee is included in the retailer’s price.
• S
amsung takes no responsibility for the water line installation. If water leaks occur, contact the installer
of the water line.
CAUTION
• M
ake sure the water filtering hose is connected to a cold, potable water source pipe.
Connecting to the hot water pipe may cause the water filter to malfunction.
1. S
hut off the water supply by closing the main water
valve.
2. Locate the cold, potable water pipe (1).
3. F
ollow the Water Line Installation to connect to the
water pipe.
NOTE
New hose-sets supplied with the appliance are to be used
and old hose-sets should not be reused.
52
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1. L
oosen and remove the compression nut (a) from
the water line of the refrigerator, and insert it to
the water filtering hose.
2. T
ighten up the compression nut (a) to connect the
water filtering hose and the water line.
3. O
pen the main water valve and check for any
leaks.
4. I f there are no leaks, dispense about 10 litres
of water or dispense the water for 6 - 7 minutes
before actually using the refrigerator to remove
impurities inside the water filtering system.
5. S
ecure the water line to a sink or a wall using a
clip.
CAUTION
• D
o not tighten the water line excessively. Make sure the
water line is not bent, pinched, or squashed.
• D
o not mount the water line on any part of the
refrigerator. This may damage the refrigerator.
NOTE
If you have to relocate the refrigerator after connecting
the water line, make sure the joined section of the water
line must is straight.
CAUTION
The water line must be repaired by a qualified professional. If you encounter a water leak, contact a local
Samsung service centre or the installer of the water line.
53
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
The water pressure of the water supply system to a reverse osmosis water filtration system must
be between 241 kPa and 827 kPa.
The water pressure of the reverse osmosis water filtration system to the refrigerator’s cold water
line must be at least 276 kPa. If the water pressure is below the specified:
• C
heck if the sediment filter in the reverse osmosis system is blocked. Replace the filter if
necessary.
• R
efill the water tank in the reverse osmosis system with water.
• I f your refrigerator has a water filter, it may further reduce the water pressure when used in
conjunction with a reverse osmosis system. Remove the water filter.
To purchase a new water filter (part type: HAFEX/EXP), contact a local Samsung service centre.
NOTE
If the filter is installed horizontally, water may remain in
the filter. Therefore, vertical installation is recommended.
CAUTION
Do not mount the water filter on any part of the
refrigerator. This may damage the refrigerator.
54
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
CAUTION
• D
o not use third-party water filters. Use only Samsung-provided or -approved filters.
• U
napproved filters may leak and damage the refrigerator, causing electric shock.
Samsung holds no responsibility for any damage that may occur from use of third party water filters.
• The filter indicator turns red as a reminder that lets you know it is time to replace the water filter.
1. S
hut off the main water supply.
2. C
onnect the water supply line to the inlet side of
the filter to the end.
3. C
onnect the dispenser line to the outlet side of
the filter.
4. C
heck if there is any leak. If not, fix the lines with
the clips.
5. P
ut the water filter into place and fix it with the
clips.
6. P
ress and hold Filter Reset for 3 seconds to reset
the filter lifecycle.
7. W
hen replacing is complete, flush 10 litres of
water (or dispense the water for 6 - 7 minutes) to
remove impurities from the water line.
CAUTION
When adjusting the length of the water line tubing, make
sure to smooth out the cut surface at a right angle.
This is to prevent a water leak.
NOTE
• A
newly installed filter may cause the water dispenser to spurt water briefly. This is because air has
entered the water line.
• T
his replacement process may involve the refrigerator to drip water onto the floor. If this happens, wipe
up with dry cloths.
55
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
•P
ress the Fridge and Vacation buttons at the same time for at least 6 seconds. The Control Display will blink with an interval of
0.5 seconds. In that case, you may take your fingers off both buttons and press the Vacation button to enter the Test Mode.
• I f any key on the front of panel is pressed within 15 seconds after the test mode, it will be operated as below sequence :
Manual operation(FF) -> manual defrost of freezer compartment(Fd) -> cancel(Display all off)
• If any key on the front of panel is not pressed within 15 seconds after the test mode, the test mode will be canceled and it will be
returned to previous mode.
1-1) I f any key is pressed once in test mode, blinks "FF" on the display and it indicates the refrigerator has entered the manual
operation. At this moment, buzzer beeps as an alarm.
1-2) I f manual operation is selected, compressor will run at once without 7 minutes delay in any mode. If the refrigerator is on
the defrost cycle at the moment, defrost will be finished and manual operation will begin.(Be careful if manual operation
get started at the moment of compressor off, over load could be occurred)
56
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
1-3) I f manual operation works, compressor & f-fan operate continuously for 24 hours and fridge compartment will be
controlled by the setting temperature.
1-4) When the manual operation runs, setting temperature will be selected automatically as below: freezer compartment
-23°C, fridge compartment 1°C.
1-5) D
uring manual operation, Power Freezer & Power Cool function will not be work.If a function is selected, the power
function icon of the selected function will be off automatically after 10 seconds.
1-6) M
anual operation can be canceled by removing power from the unit, then resupplying power.
1-7) Alarm(0.25 sec ON/ 0.75 sec OFF) will beep continuously until manual operation is completed and there is no function to
make the sound stop.
2) Forced Defrost
2-1) W
hen you press any key one more time at the manual operation status, Fd lights up on the Display Panel. At this time, the
Forced Operation stops immediately and F-Defrost will be performed at the same time.
2-2) A
t this time, it will send out “Beep” sound for 2 seconds and then it will perform Forced F Defrost while sending out “0.5
sec On and 0.5 sec Off” sound.
3) Test cancel mode
3-1) D
uring the defrosting of freezer compartment if the display panel change to the test mode and test button is pressed one
more time, defrosting of freezer compartment will be canceled and the unit will return to the normal operation.
Or, all test functions will be canceled by turning main power ON and OFF.
57
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
① If Fridge Key + Vacation Key are pressed simultaneously for 10 seconds, the error mode by self-diagnosis will
be canceled.
58
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
② If Fridge Key + Vacation Key are pressed simultaneously for 10 seconds, the self-diagnosis function will be
selected.
2-1) I f Fridge Key + Vacation Key are pressed simultaneously for 6 seconds during normal operation, the temperature setting
display will operate for 4 seconds (ON/OFF 0.5sec each).If Fridge Key + Vacation Key are pressed simultaneously for 10
seconds (including above 4seconds), self-diagnostic function will be selected.
2-2) At this moment, self-diagnostic function will be returned with buzzer sound.If there is an error, display of error will be
operated for 30 seconds and then return to normal condition whether problem is corrected or not. (Refer to self-diagnosis
CHECK LIST)
2-3) I nput by button is not accepted during self-diagnostic function.
59
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Self-diagnostics check list
F R
LED
Item Trouble contents Diagnostic method Image
F R
60
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
■ Self-diagnostics check list
LED
Item Trouble contents Diagnostic method Image
F R
Separation of freezer
After separating Main PCB
compartment defrost heater
CN70& CN81 wire from PCB,
housing part, contact error,
Resistance value between
disconnection, short circuit
CN70 5PIN - CN81 1PIN
or temperature fuse error.
F-DEF Error Shall be 63(230) ohm ±
Display error : the defrosting
7%(Resistance value is varied
does not finish though
by input power) 0 ohm : heater
freezer compartment defrost
short, ∞ ohm : wire/bimetal
is heating continuously for
open (Must power off).
more than 100 minutes.
61
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED
Item Trouble contents Diagnostic method Image
F R
Actually, If there is not a
Display pc - Er in the panel
Panel ↔ Main problem, it is desirable to
with alarm :
Communication replace Main and Panel PCB
MICOM MAIN PANEL
Error With the oscilloscope after a
communication error.
cable problem confirming.
Actually, If there is not a
Main - Inverter Display 44C in the panel : problem, it is desirable to
Communication Inverter MICOM Main MICOM replace Main and Inverter PCB
Error communication error. With the oscilloscope after a
cable problem confirming.
I/O Expander Display 46C in the panel :
It is desirable to replace Main
Communication I/O Expander ↔ Main MICOM
PCB.
Error communication error.
Actually, If there is not a
Dispenser
problem, it is desirable to
Panel ↔ Main MICOM MAIN ↔ DISPENSER
replace Main and Panel PCB
Communication PANEL communication error.
With the oscilloscope after a
Error
cable problem confirming.
62
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
LED
Item Trouble contents Diagnostic method Image
F R
63
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
① If Fridge Key and Vacation Key are pressed simultaneously for 6 seconds, ALL ON/OFF will blink with
0.5interval for 4 seconds.
② If take the finger off from above keys and press Freezer Key, load condition mode will be started.
1) I f Fridge Key and Vacation Key are pressed simultaneously for 6 seconds during normal operation, the temperature setting
display of Fridge and freezer compartments will blink ALL ON/OFF with 0.5 for 4 seconds.
2) At this moment, If Freezer Key after Fridge Key and Vacation Key is pressed, load condition display mode will be returned with
alarm. At LED all on state, only load condition display will blink ON/OFF with 0.5 seconds interval.
3) L oad condition display mode shows the load that micom signal is outputting.
However, It means that micom signal is outputting, it does not mean whether load is operating or not. That is to say that though
load operation is displayed, load could not be operated by actual load error or PCB relay error etc. (This function would be
applied at A/S.)
4) Load condition display function will maintain for 30 seconds and then normal condition will be returned automatically.
5) L oad condition display is as below. Only the load control LED will blink with 0.5interval in "Display LED".
64
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
10 F-DEF HEATER F-1-ⓓ When F-DEF HEATER operates, applicable LED blinks.
11 C-FAN HIGHEST F-1-ⓔ,ⓕ When C-FAN HIGHEST operates, applicable LED blinks.
12 C-FAN HIGH F-1-ⓔ When C-FAN HIGH operates, applicable LED blinks.
13 C-FAN LOW F-1-ⓕ When C-FAN LOW operates, applicable LED blinks.
14 F Valve F-10-ⓑ When F Valve operates, applicable LED blinks.
15 Dispenser Heater F-10-ⓔ When Dispenser heater operates, applicable LED blinks.
16 FlexZone Damper F-10-ⓕ When FlexZone Damper operates, applicable LED blinks.
17 R Damper F-10-ⓖ When R Damper operates, applicable LED blinks.
65
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
4-4-4. Exhibition Mode setting function (All regions except for North America)
① Press the Fridge and Vacation buttons at the same time for at least 6 seconds. The Control Display will blink
with an interval of 0.5 seconds. In that case, you may take your fingers off both buttons and press the Lock
button to enter the Exhibition Mode.
66
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
•P
ress the Fridge and Vacation buttons at the same time for at least 6 seconds.The Control Display will blink with an interval of
0.5 seconds. In that case, you may take your fingers off both buttons and press the Fridge button to enter the Option Setting
Mode.
②
①
② If take the finger off from above keys and press Fridge Key, Option setting mode will be started.
67
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Reference Value
Reference Value Up
Code
68
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
• I f the display changes to option setting mode, all displays will be off except freezer and fridge compartments temperature
display as below.(Fridge and freezer compartments case will be explained only because all options are operated with the same
method according to the option table.)
Reference Value
Code
1) For example, if you want to change freezer compartment standard temperature to -2°C by operating option, do as
below. This function is for changing the standard temperature.
In -19°C of current temperature of freezer compartment, if you make the temperature lower to -2°C by the option, the
standard temperature would be controlled -21°C.
Therefore, if you change the setting of temperature option to -19°C on the panel, the appliance will be operated with
-21°C. It means that standard temperature is controlled -2°C less than setting temperature in the display.
Note
Basically, all the data in option has cleared from the factory.Therefore, almost all setting value are "0“.But,
some setting values could be changed for the purpose of improving performmance.NOTE You need to check
the product manual and/or specification.
2) After changing to the option mode, fridge compartment "0" , freezer compartment "0" will be displayed. ( Basically
fridge compartment "0", freezer "0" would be set at shipping process, but setting value could be changed for the
purpose of improving product at mass producing process.)
- I f fridge compartment "0" shows only, temperature reference value of freezer compartment will be set and current
freezer compartment temperature code will be displayed on the freezer temperature display.
3) I f freezer compartment "4" is set as below freezer compartment code after fridge compartment "0 is set, standard
temperature of freezer compartment will be lower than -2.0°C.
(Refer to the picture "changing the freezer compartment temperature")
69
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Reference Value
Code
: I f you wait for 20 seconds after completing the setting, MICOM will save the setting value to the EEPROM and normal
display will be returned and the option setting mode will be canceled.
4) By the same method as above, it is possible to control the fridge compartment temperature, water supply, ice-maker
harvest temperature/time, defrost return time etc.
5) Option
function is set in the EEPROM at shipping process in the factory.
You would better not to change the option of your own.
Completing the setting is that option function return to normal display after 20 seconds.
Do not turn off the appliance before returning to the normal display mode.
Note
Option setting function exists in the other items.We will skip the explanation of the other functions by the
option because it is associated with refrigerator control function and is not needed at SERVICE.
(Please do not set the other options except above SERVICE Manual.)
70
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Setting value
FZ
Temp.
compartment
compensation
Code
0 0.0°C
1 -0.5°C
2 -1.0°C
3 -1.5°C Reference Value
4 -2.0°C
5 -2.5°C
6 -3.0°C
7 -3.5°C
8 +0.5°C
9 +1.0°C
10 +1.5°C
11 +2.0°C
Code
12 +2.5°C
13 +3.0°C
14 +3.5°C
15 +4.0°C
Setting value
FZ
Temp.
compartment
compensation
Code
0 0.0°C
1 -0.5°C
2 -1.0°C
3 -1.5°C Reference Value
4 -2.0°C
5 -2.5°C
6 -3.0°C
7 -3.5°C
8 +0.5°C
9 +1.0°C
10 +1.5°C
11 +2.0°C Code
12 +2.5°C
13 +3.0°C
14 +3.5°C
15 +4.0°C
ex) If you want to change the Fridge compartment standard
temperature to 2°C.
71
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Setting value
FZ
Water
compartment
Settings.
Code
0 92cc
1 105cc
Setting value
FZ
compartment Setting time
Code
0 90min
1 89min
2 88min
3 87min
4 86min
5 85min
6 84min
7 83min
8 82min
5) E
ject temperature changing table of freezer compartment Ice Maker
(In DISPENSER MODEL Only features)
Setting value
FZ
Temp.
compartment
compensation
Code
0 -17.0°C
1 -16.0°C
2 -15.0°C
3 -14.0°C
4 -13.0°C
5 -12.0°C
6 -18.0°C
7 -19.0°C
72
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Setting value
FZ
compartment Comp RPM
Code
0 No RPM Change
1 Minimum 2450RPM
2 Minimum 2450RPM
3 Minimum 2450RPM
7) T
emp Display Option.
- This option is for temp display all on mode.
If user wants temp display always on, this option is solution.
Setting value
FZ
compartment Temp Display Option
Code
Normal Display (Temp display
0
temporally on at use)
1 Always Temp Display On
2 Always Temp Display On
73
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Setting value
FZ compartment
Rate change
Code
0 +0.0%
+ 20%
1 operation
( up to 100% )
9) Temperature changing table of Flex Room compartment. (in FLEX ROOM Model Only features)
Setting value
FZ
Temp.
compartment
compensation
Code
0 0.0°C
1 -0.5°C
2 -1.0°C
3 -1.5°C
4 -2.0°C
5 -2.5°C
6 -3.0°C
7 -3.5°C
8 +0.5°C
9 +1.0°C
10 +1.5°C
11 +2.0°C
12 +2.5°C
13 +3.0°C
14 +3.5°C
15 +4.0°C
74
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
DATA1.Temperature table
Resistance value and MICOM port voltage of sensor according to the temperature
SENSOR CHIP : b ased on PX41C, PX41C, 502AT/ 103**(ICE MAKER SENSOR(MOLD)/FULL UP, 20Kohm
( Actual measurement = value of the table below X 2 )
75
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
76
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Input
terminal
Start
AC input power and high
voltage of DC 310V or higher
CAUTION are generated at PCB. Be
cautious during repair and No
measurement. Is power plug connected?
Yes
Connect the plug, or correct loose plug.
No
Is normal voltage of 12V and 5V
generated on PCB?
Yes
PCB assembly replacing.
No
Is operation of panel
PCB normal?
1) Checking and repair of power cable
Yes assembling.
Yes 2) Panel PCB replacing.
Is soldering short or
cracked on PCB?
No 1) Soldering again.
2) Main PCB replacing.
Normal (checking again)
77
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Start
F-DEF Sensor is NO
normal (with Self Diagnosis)
Replace the sensor.
YES
NO
F-DEF Heater is normal
CN70
YES
NO It goes
back to Cooling Operation after
heating
Check all the sensors
YES
Note Normal
When F-DEF Sensor is higher than
+10℃ and +17℃, it will stop heating
and go back to Cooling Operation.
MAIN PBA NO
connectors are normal.
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
YES Repair the connectors
cnSP@CT@@CW cnSP@CQ@@CT
Precautions(Safety Warnings)
When there is sensor error, display panel show that. When it occurs during the initial power on time, display
panel keeps blinking relevant 7-SEG and the refrigerator go into the emergency operation mode.
Under the emergency operation mode, the refrigerator can not do its normal operation. So check out with the
Self Diagnosis in this manual.
YES
Ambient-Sensor : Read the resistance
between CN40 #18 and #20.
PBA & Thermistor are ok. Replace Thermistor.
Check the contact of the connector again.
Compare the room temp. with
sensed temp. using Temp-
Resistance Table.
2) When the Fridge Temp Sensor is defective (also applied to other sensors)
Start
MAIN PBA NO
connector (CN20) is inserted
properly.
Repair the defective contact
YES of the connector or insert
The order of the connector properly
Connector(CN30) is the same NO
as the one in the circuit
diagram
Check the circuit diagram and
YES correct any wrong inserted
Refer to Circuit Diagram and Temp connectors.
The voltage NO
Sensor Troubleshooting in this between CN20 #10 and #12 is within
manual. the normal range.
Check MAIN PBA Cold
YES
Solder or Short.
PBA & Thermistor are good.
Check the contact of the connector again.
79
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
80
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Start
"DingDong"
Sounds when a button on the NO
display panel is pressed
NO Normal
The Buzzer
surface is broken/bended. YES
Or Buzzer lead comes off from
the vibration plate.
Buzzer Breakage
NO Replace Buzzer.
Check
the wiring - short / open YES
(buzzer ↔ Display in fridge)
81
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Start
YES
Child Lock is on
82
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
- F-Fan motor usually runs together with the Compressor. Once the door is open and closed at high
ambient temperature, F-Fan motor put off its operation for one minute. Therefore, you are advised not to
take it as an error.
- When fridge door is open, the F-Fan motor stops.
Start
NO
COMP is on?
83
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
4-5-7. When the internal lamp of the freezer/fridge does not light up
1. Turn off the power for repair because there is risk of electric shock when replacing the internal lamp.
2. Please keep in mind you could get burnt by the excessive heating of an incandescent light bulb.
Reference
Reference
1. When the DOOR is open, the DOOR S/W becomes OPEN. Micom senses 5V from Door S/W and recognizes that
the Door is open. If 5V has sensed for more than 2 minutes, buzzer will sounds “DingDong” every 1 minute.
Therefore, if the DOOR S/W is defective, it can generate the “Ding Dong” sound every 1 minute.
2. ON/OFF control of the internal lamp is linked with the DOOR S/W.
Start
84
This document cannot be used without Samsung's authorization
Precautions(Safety Warnings)
Protecting
LED Blinking Frequency Remarks
Functions
Normal
N/A
Operation
85
This document cannot be used without Samsung's authorization
5. PCB DIAGRAM
Precautions(Safety Warnings)
Precautions(Safety Warnings)
CN40 CN60
1. STEP VALVE A 1. 5V
2. MAIN DISPLAY TX 2. 12V
3. STEP VALVE B 3~4. GND
4. MAIN DISPLAY RX 5. FLEXZONE ROOM-SENSOR
5. 12V 8. ICE&WATER S/W
6. 12V 10. CUBE MOTOR S/W
7. STEP VALVE A/ 12. ICE ROUTE S/W
8. GND 13. FLEXZONE DAMPER B
9. STEP VALVE B/ 14. 5V
10. F-LED 15. FLEXZONE DAMPER B/ (WATER PUMP MOTOR)
12 GND 16. GND
14. HUMIDITY-SENSOR 17. FLEXZONE DAMPER A/
16. GND 18. 12V
17 R-ROOM DAMPER B 19. FLEXZONE DAMPER A (ICE MAKER PUMP MOTOR)
CN20 20. DISPENSER DISPLAY RX
18. AMBIENT-SENSOR
1. F-DOOR S/W 19. R-ROOM DAMPER B/ 21. FLEXZONE DAMPER HEATER
2, R-DOOR S/W 20. GND 22. DISPENSER DISPLAY TX
CN04
3~4. GND 21. R-ROOM DAMPER A/ 23. 12V
1. WI-FI RX
5. F-DEF-SENSOR 23. R-ROOM DAMPER A 24. GND
2. GND 26. WATER STOP VALVE
6. 5V 25. R-ROOM DAMPER HEATER
26. R-LED 3. WI-FI TX ※ N/A : 6, 7, 9, 11, 25
7~8. GND
27. 12V 4. WI-FI RESET
9. F-SENSOR
28. GND 5, +12V
10. R-SENSOR
※ N/A : 11, 13, 15, 22, 24 6. +5V
11~12. GND
13. F-FAN F/G
15. F-FAN
17~18. GND CN90
19. WATER TANK HEATER 1. 12V
20. C-FAN F/G 2. GND
22. C-FAN 5. WATER PIPE HEATER
23. 12V 7. ICE MAKER MOTOR(CW)
9. ICE MAKER MOTOR(CCW)
24.GND
11. ICE MAKER SENSOR
※ N/A : 14, 16 21 13. GND
15. ICE MAKER TEST S/W
CN70
17. 5V
3. DISPENSER HEATER 18. 12V
5. F-DEF HEATER 19. HORIZONTAL HALL IC
7. COM2 21. GND
※ N/A : 1 22. 5V
24~26. GND
CN71 28. 5V
1. ICE COVER ROUTE G-MOTOR ※ N/A : 3, 4, 6, 8, 10, 12, 14, 16, 20, 23, 27
3. WATER SOL-VALVE
5. ICE/WATER SOL-VALVE
CN71-1 CN102
1. CUBE-MOTOR 1. COMP U
3. AUGER-MOTOR 2. COMP V
5. COM1 3. COMP W
CN80
1. COM1 CN85
3. COM2 1. COM2
3. COM1
5. EARTH
87
CN60
CN60
12V 2 1 5V
GND 4 3 GND
12V
R-ROOM DAMPER B
STEP VALVE B
R-ROOM DAMPER B/
R-ROOM DAMPER A/
STEP VALVE A/
STEP VALVE B/
12V
R-ROOM DAMPER HEATER
R-ROOM DAMPER A
N/A
N/A
N/A
STEP VALVE A
N/A 6 5 FLEXZONE ROOM-SENSOR
ICE&WATER LEVER 8 7 N/A
7
9
1
3
5
12V
GND
F-FAN
GND
F-FAN F/G
GND
WATER TANK HEATER
N/A
F-DOOR S/W
GND
F-SENSOR
F-DEF-SENSOR
25
27
21
23
11
13
15
17
19
CUBE MOTOR S/W 10 9 N/A
7
9
1
3
5
CN40
21
23
17
19
11
13
15
CN40
2
4
6
24
26
28
10
12
14
16
18
20
22
ICE ROUTE S/W 12 11 N/A
CN20
CN20
2
4
6
22
24
16
18
20
10
12
14
5V 14 13 FLEXZONE DAMPER B
12V
N/A
N/A
GND
GND
GND
GND
GND
F-LED
R-LED
FLEXZONE DAMPER B/
GND 16 15
5V
(WATER PUMP MOTOR)
N/A
N/A
GND
GND
GND
GND
GND
C-FAN
12V 18 17 FLEXZONE DAMPER A/
R-SENSOR
C-FAN F/G
FLEXZONE DAMPER A
DISPENSER DISPLAY RX 20 19
MAIN DISPLAY TX
MAIN DISPLAY RX
(ICE MAKER PUMP MOTOR)
AMBIENT-SENSOR
R-DOOR S/W
HUMIDITY-SENSOR
DISPENSER DISPLAY TX 22 21 FLEXZONE DAMPER HEATER
GND 24 23 12V
Precautions(Safety Warnings)
88
CN90
CN90
GND 2 1 12V
N/A 4 3 N/A
N/A 6 5 WATER PIPE HEATER
N/A 8 7 ICE MAKER MOTOR(CW)
N/A 10 9 ICE MAKER MOTOR(CCW)
N/A 12 11 ICE MAKER SENSOR
N/A 14 13 GND
N/A 16 15 ICE MAKER TEST S/W
12V 18 17 5V
This document cannot be used without Samsung's authorization
6. WIRING DIAGRAM
6-1. Model : 2 Door, Dispenser (In-Door Ice Maker) RS74R5***, RS65R5***, RS64R5***
89
This document cannot be used without Samsung's authorization
Wiring Diagram
90
This document cannot be used without Samsung's authorization
7. BLOCK DIAGRAM
91
This document cannot be used without Samsung's authorization
Digit 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Interior Buyer
Type Capacity Series I Year Series II Exterior Option Energy Color /
Option Code
Model
Code R S 6 4 R 5 6 7 1 S L / E U
Handle :
Recessed only
92
■ Series 1 (Digit 4)
Option
IceMaker Material I & W Dispenser IceMaker Handle
5 ○
PP Indoor (AUTO)
4 ○
3 - - Slim Indoor Recessed
2 - - Twist
1 - - Tray
Option Plumbing/
Handle Deco Display
Non Plumbing
6 Plumbing -
3 Door
5 - -
4 Plumbing -
Hidden (internal)
3 Non Plumbing -
-ADA
2 Door 2 Plumbing ○
1 Non Plumbing ○
0 - -
Option
FlexZone EZ Silde Shdlf Metal Cooliing (duct) Wine rack
9 ○ ○ ○ ○
8 ○ ○ - ○
3 Door 7 - ○ ○ ○
6 - ○ - ○
4 ○ ○
3 ○ -
2 Door
1 - ○
0 - -
Asia gspn2.samsungcsportal.com
China china.samsungportal.com