14
Peregrine EDi and 1300 Series EDi
Engine management system wiring diagrams
‘Components (A) (numbers shown in triangles)
Main power relay forthe engine control module
AN |ecw)
Air-valve solenoid forthe exhaust brake
\ pve coin oth a= wate bata
Transmission kek-down relay
AX | Star into retay
To the transmission controls
[\ starter motor relay
Two-speed axle switch, a = low, b = high
/\ |Disgnostic connector
TRamand aalich a nrwnana pawar fam Tan a
conditioning compressor
/\, |Diegnostc switch
[Ai-vaive solenold forthe radiator fan
\ [tnt wae ith ost on
Peeper ->
Aic-valve solenoid forthe radiator-shutter
ECM pin-outs (A)
1 _[ Negative ()for the DC 7 DC converter
2_| Negative) forthe DC / DC converter
16 | Posiive (+) forthe ATA Gata link
17_[ Negative (forthe ATA SAE J1708
21_| Posiive (+) forthe DO/DC converter
22_[ Negative () from the battery
24 | Postive (+) from he ignition switch, whan ON"
25__| Control output forthe power relay
75 [Tapa ram the tun switch, 79 v whan Tha eval ARargaged
728_[ Input rom two-speed axle ewitch
'33_[ Input rom the demand switch to increase power rom the air condoning compressor
'34_[ Input rom the self-test switch
41_| Positive (from the battery
“2 Negative () for outputs
46 | Outputto the star inhibit relay
‘@7_| Output to the electric fan
1_| Output to the radiator-shuttor
"36 | Output to the kick-down relay
208
This document has been printed from SPI?. Not for Resale
Workshop Manual, 1PD 13536, Issue 3Peregrine EDi and 1300 Series EDi 14
Wiring diagram (A)
bh ee
Workshop Manual, TPD 13536, Issue 3 205
This document has been printed from SPI?. Not for Resale14
‘Components (8) (numbers shown in triangles)
Peregrine EDi and 1300 Series EDi
[Brake switch number 1, a= off,b = on
[Waringlight to show thal the pressure controlmode
is active
/\ Brake swich number 2, a= off,b = on
Remote speed control sensor
[Cruise-contro, a = off, b = on
Hydraulic pressure switch
[\, |Remote PTO switch, 8 = on, b= off
‘Accelerator pedal position sensor
/\, |Speed switch, a = reset accelerator, b = set coast
Barometric absolute pressure sensor
[\ [Speed sac, remote, a= reel acannon, b= set
Jooast
[ambient air temperature sensor
Pre-set speed switch, a = off, b= on
\Vehicle speed sensor
|Variable speed switch, a= of, b= on
Instrumentation
J, |Hysrauic pressure governor switch
Coolant level switen
Hycrautic pressure govemor control relay
PPP PPP PrP
(Computer data link connector
[Warning light to show thatthe speed control modes
active
Fo
This document has been printed from SPI?. Not for Resale
Workshop Manual, 1PD 13536, Issue 3Peregrine EDi and 1300 Series EDi 14
‘Wiring diagram (B)
Workshop Manual, TPD 13536, Issue 3 a
This document has been printed from SPI?. Not for Resale14 Peregrine EDi and 1300 Series EDi
Eom pin-outs (6)
[Reference vakage (76 othe peed cone seraor
[Frauke pressure gover erable input
5 Retrenca vlogs (= 5 for To oa apa GOTT SST
| (00) for te remote speed onl sensor
7
3
Rafarance vallage (+ 5y) forthe hydrauls pressure Sensor
Tnput from the speed contol sensor
O [Not used
10 [Input from the coolant level switch
14_|(0v) fr the speed control sensor
"12_| Input rom the ambient air temperature sensor
13 [Input from the hydraulic pressure sensor
Ta [ Not used
118 | Interforence screen forthe computor data ink connector
79 _| Computer access postive (#)
720 | Computer access negative ()
727_[Tnput from the speed control sansor, to Sonfm thal the Speed corrals Inthe Idle postion |
723 [Input from the atmospheric air pressure sensor
'30_| Input rom the remote epeed contol sensor
31_[ Input rom the resume / accelerate switch
'32_[Input rom the cruse-contol (set coast)
'35_[ Input from the crise-control (on off)
'36 [Input rom the variable speed switch, forthe remote speed contol
'37_[Inpat rom the pre-set speed switch, for the remote spead control
36_[ Notused
39 | Poslive (inpul om he variable speed wallch
40_| Negative input from the vehicle speed sensor
“3_[ Input rom the number 1 brake switch (en ff)
“44 [Input from the number 2 brake switch (on / off)
5_| Service interval warring lamp
6 [ Output to the shit-up waming Tamp
49 _[ Outputto the control relay Tor the hyd pressure governor
‘2 [ Not used
'53_[ Output to the glow plug warming amp
‘54 | Output to the of water warning lamp (pressure / temperature)
'55_ | Output the engine waming lamp
‘57 | Output to the vehicie speed sensor, calibration B
‘58 | Ouiputto the vehicle speed sensor, calibration A
59 | Output to the tachometer, A
0 [ Ouiput to the tachometer, B
WW Workshop Manual, 1PD 13536, Issue 3
This document has been printed from SPI?. Not for ResalePeregrine EDi and 1300 Series EDi 14
‘Wiring diagram (C)
Workshop Manual, TPD 13536, Issue 3 73
This document has been printed from SPI?. Not for ResaleThis page is intentionally blank
This document has been printed from SPI?. Not for Resale