Professional Documents
Culture Documents
Gate-Cut Springs Washers For Coil Springs: Quotation
Gate-Cut Springs Washers For Coil Springs: Quotation
D±0.5
・Flange part of the spring and holder is press fitted. However, the spring
d −0.3
0
and holder could come off depending on the usage environment.
Please refrain from using the spring in an unlocked state.
Fixed installation plate
a 3
+0.1
P 0 ・Please do not use it with over maximum allowable deflection (F=L×40%).
It become easy for the spring and the holder to come off, and it is Runner stripper plate
L ±0.5 D1±0.1
F very dangerous.
・Please use within the allowable temperature.
R ・Data on load was taken at room temperature (less than 40℃).
①Coil springs Equivalent of SWOSC-V Although it may vary depending on various conditions, N{kgf} load
(Steel Wire Oil Temper Silicon for Valve) Socket head cap screws
②Holders S45C
usually decreases when used in temperature higher than room (CB) P.1185
S (Holder section) Fe3O4(Black oxide)
temperature.
Quotation
20 11.5 19.9 275.6{28} 441.3{45} 5.0 8 7
35 31.5{3.2} 19 8.7 14 20-35 6.0 10 9 1.0
40 27.6{2.8} 21 10 16 20-40 7.0 12 11.5
Springs
8.0 14 13
25 53.9{5.5} 14 6.2 10 WSW 22-25
9.0 16 15
2.0
30 45.0{4.6} 16 7.5 12 22-30
Quotation
(Heat resistant 10.0 18 17
22 12.7 35 21.9 3.5 38.5{3.9} 17 8.7 337.5{35} 14 539.4{55} 120℃) 22-35 12.0 20 SSWA 19
3.0
6.2 M6
40 33.7{3.4} 23 10 16 22-40 12.0 22 21
4.0
45 30.0{3.1} 25 11.2 18 22-45 14.5 25 24
+0.3 15.0 27 26
30 61.3{6.3} 18 7.5 12 25-30 d+0.1 5.0
17.0 30 29
6.3
6.3
35 49.0{5.0} 21 8.7 14 25-35 −0.1 0 20.0 35 34
25 15 40 24.9 4 42.9{4.4} 22 10 428.6{44} 16 686.5{70} 25-40 D−0.3 t −0.1 R SS400 23.0 40 39
45 38.1{3.9} 25 11.2 18 25-45 Applicable Part Number U/Price
50 34.3{3.5} 27 12.5 20 25-50 SSWB d ℓ
spring dia. Type D 1~19
45 43.6{4.4} 25 11.2 18 30-45 3.5 4.0 8 7
30 17 50 29.9 4.5 39.2{4.0} 27 12.5 490.3{50} 20 784.5{80} 30-50 4.5 5.0 10 9
Quotation
5.5 6.0 12 11
55 35.7{3.6} 30 13.7 22 30-55 6.5 7.0 14 13
Durable number of times used One million times 300,000 times 7.5 8.0 16 15
V Use Fmm* within F=L×35%. V The solid height values are for reference only. There may be some dispersions depending on the lot. V kgf=N×0.101972 8.5 9.0 18 17
■Heat resistant 200℃type C1.0
9.5 10.0 20 SSWB 19
10.5 11.0 22 21
N/mm Solid F=L×25% F=L×30% Bolt Part Number U/Price 12.0 12.0 25 24
D d L D1 P a {kgf/mm} Height Fmm Load N{kgf} Fmm Load N{kgf} used Type D-L 1~19 13.0 13.0 27 26
−0.3 14.5 15.0 30 29
20 32.7{3.3} 14 5.0 Outside allowable range 16-20 d−0.5
17.0 17.0 35 34
16 9 25 15.9 5.2 26.2{2.7} 16 6.2 163.4{17} 7.5 M5 16-25 −0.1 0 0
30 21.8{2.2} 19 7.5 9.0
196.1{20}
16-30
D−0.3 3−0.1 ℓ−0.3 R SS400
19.5 20.0 40 39
U SWC type not applicable.
20 39.2{4.0} 14 5.0 Outside allowable range 18-20
Applicable Part Number U/Price
18 11 25 17.9
3
31.4{3.2} 16 6.2 196.1{20} 7.5
235.4{24}
18-25 SSWC 3 −0.1
0 d ℓ spring dia. Type D 1~19
30 26.2{2.7} 19 7.5 9.0 18-30 3.5 4.0 8 7
25 39.2{4.0} 16 6.2 7.5 20-25 4.5 5.0 10 9
C1.0
Quotation
30 32.7{3.3} 19 7.5 9.0 20-30 5.5 6.0 12 11
Quotation
Part Number
WSW20-35 Quotation Quotation Quotation
1259 WSV20-35 1260