Professional Documents
Culture Documents
OMV OMT 500 Danfoss
OMV OMT 500 Danfoss
Orbital Motors
OMT and OMV
www.danfoss.com
Technical Information
OMT and OMV Orbital Motors
Contents
Orbital motors
Orbital Motors Introduction......................................................................................................................................................... 5
Orbital Motors Features............................................................................................................................................................ 5
Technical Features...................................................................................................................................................................... 5
Orbital Motors Application Areas..........................................................................................................................................5
Orbital Motors Literature Overview...........................................................................................................................................6
Speed, torque, and output............................................................................................................................................................7
OMT
Versions................................................................................................................................................................................................8
Features.......................................................................................................................................................................................... 8
Code numbers................................................................................................................................................................................... 8
Ordering......................................................................................................................................................................................... 9
Technical data....................................................................................................................................................................................9
Maximum permissible shaft seal pressure.........................................................................................................................9
Motor with check valves and without use of drain connection........................................................................... 9
Motor with check valves and with drain connection............................................................................................... 9
Motor with check valves and with drain connection............................................................................................. 10
OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH......................................................................................................10
Pressure drop in motor...........................................................................................................................................................12
Oil flow in drain line.................................................................................................................................................................12
Direction of shaft rotation..................................................................................................................................................... 13
Permissible shaft loads for OMT..........................................................................................................................................13
OMT Function diagrams.............................................................................................................................................................. 14
Function diagram use............................................................................................................................................................. 17
Shaft version.................................................................................................................................................................................... 18
Port thread versions.................................................................................................................................................................21
Dimensions.......................................................................................................................................................................................22
OMT standard flange - European version........................................................................................................................ 22
OMT standard flange - US version...................................................................................................................................... 24
OMT Wheel - European version...........................................................................................................................................26
OMT Wheel - US version.........................................................................................................................................................28
OMT Brake-wheel - European version...............................................................................................................................30
OMT Brake-standard - European version......................................................................................................................... 32
OMT short - European version............................................................................................................................................. 33
OMTS.................................................................................................................................................................................................. 34
Installation...................................................................................................................................................................................34
Attached component dimensions......................................................................................................................................35
Attached component internal splines.............................................................................................................................. 35
Motor or attached component drain connection.........................................................................................................36
OMT versions and code numbers
OMV versions and code numbers
OMV versions and code numbers............................................................................................................................................ 38
OMV technical data
OMV, OMVW, OMVS technical data.........................................................................................................................................40
Maximum permissible shaft seal pressure............................................................................................................................40
Motor with check valves and without use of drain connection.............................................................................. 40
Motor with check valves and with drain connection.................................................................................................. 41
Pressure drop in motor................................................................................................................................................................ 41
Oil flow in drain line...................................................................................................................................................................... 41
Direction of shaft rotation...........................................................................................................................................................42
Permissible shaft loads.................................................................................................................................................................42
OMV mounting flange: Standard........................................................................................................................................42
OMV mounting flange: Wheel............................................................................................................................................. 43
OMV mounting flange: SAE-C.............................................................................................................................................. 43
OMV function diagrams
OMV 315 function diagram........................................................................................................................................................ 45
Contents
Orbital motors
Technical Features
The program is characterized by technical features appealing to a large number of applications and by
motors that can be adapted to a given application.
Adaptions comprise the following variants:
• Motors with:
‒ integrated negative holding brake
‒ speed sensor
‒ black finish paint
• Short motors without bearings or Ultra short motors
• Wheel motors with recessed mounting flange
Orbital motors
• Forestry equipment
• Lawn and turf equipment
• Machine tools and stationary equipment
• Marine equipment
• Special purpose
Orbital motors
Maximum torque
lbf• in N• m
22000
2400
20000
2200
18000 2000
16000 1800
14000 1600
1400
12000
1200
10000
1000
8000
800
6000
600
4000 400
2000 200
160 200 250 315 400 500 315 400 500 630 800
Maximum output
hp kW
80 60
50
60 40
40 30
20
20 10
160 200 250 315 400 500 315 400 500 630 800
OMT OMV
1 2
1. Intermittend values
2. Continuous values
The bar diagrams above are useful for a quick selection of relevant motor size for the application. The
final motor size can be determined by using the function diagram for each motor size: see OMT Function
diagrams on page 14, or OMV function diagrams on page 45.
The function diagrams are based on actual tests on a representative number of motors from our
production. The diagrams apply to a return pressure between 5 and 10 bar [75 and 150 psi] when using
mineral based hydraulic oil with a viscosity of 35 mm2/s [165 SUS] and a temperature of 50°C [120°F].
OMT
Versions
OMT versions
Mounting Shaft Port size Europea US Drain Check valve Low High Main type
flange n version version connection pressure pressure designation
release release
Standard Cyl. 40 mm G 3/4 X Yes Yes OMT
flange
Cyl. 1.5 in 1 1/16-12 UN X Yes Yes OMT
Splined 1.5 in G 3/4 X Yes Yes OMT
1 1/16-12 UN X Yes Yes OMT
Tapered 45 mm G 3/4 X Yes Yes OMT
Tapered 1.75 in 1 1/16-12 UN X Yes Yes OMT
P.t.o. G 3/4 X Yes Yes OMT
Wheel Cyl. 40 mm G 3/4 X Yes Yes OMTW
Tapered 45 mm G 3/4 X Yes Yes OMTW
Tapered 1.75 in 1 1/16-12 UN X Yes Yes OMTW
Brake-wheel Wheel bolt flange G 3/4 X Yes No X OMT FX
Thread hole flange G 3/4 X Yes No X OMT FX
Brake- Cyl. 40 mm G 3/4 X Yes No X OMT FL
standard
Splined 1.5 in G 3/4 X Yes No X OMT FL
Cyl. 40 mm G 3/4 X Yes No X OMT FH
Splined 1.5 in G 3/4 X Yes No X OMT FH
Short No output shaft G 3/4 X Yes Yes OMTS
Features
Features available (options):
• Speed sensor
• Motor with tacho connection
• Viton shaft seal
• Painted
• Ultra short
Code numbers
OMT
Ordering
Add the four digit prefix “151B” to the four digit numbers from the chart for complete code number.
Example:
151B3002 for an OMT 250 with standard flange, cyl. 40 mm shaft and port size G 3/4.
Technical data
151-320.10
OMT
151-1405.10
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)
151-1674.10
– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation
Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH
Type OMT OMT OMT OMT OMT OMT
OMTW OMTW OMTW OMTW OMTW OMTW
OMTS OMTS OMTS OMTS OMTS OMTS
OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX
OMT FL OMT FL OMT FL OMT FL OMT FL OMT FL
OMT FH OMT FH OMT FH OMT FH OMT FH OMT FH
OMT
Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH (continued)
Type OMT OMT OMT OMT OMT OMT
OMTW OMTW OMTW OMTW OMTW OMTW
OMTS OMTS OMTS OMTS OMTS OMTS
OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX
OMT FL OMT FL OMT FL OMT FL OMT FL OMT FL
OMT FH OMT FH OMT FH OMT FH OMT FH OMT FH
2) Peak load: the permissible values may occur for max. 1% of every minute.
For maximum permissible combination of flow and pressure, see function diagram for actual motor.
2) Peak load: The permissible values may occur for maximum 1% of every minute.
OMT
Brake motors
Type Maximum presssure in Holding torque4) Brake-release pressure3) Maximum pressure in
drain line3) brake line
OMT FX, OMT FL 5 bar 1200 Nm 12 bar 30 bar
[70 psi] [10620 lbf·in] [170 psi] [440 psi]
OMT FH 5 bar 1200 Nm 30 bar 280 bar
[70 psi] [10620 lbf·in] [440 psi] [4060 psi]
3) Brake motors must always have a drain line. The brake-release pressure is the difference between the pressure in the brake line and the pressure
in the drain line.
4) For the supply of motors with holding torques higher than those stated, please contact the Danfoss sales organization.
For maximum permissible combination of flow and pressure, see function diagram for actual motor.
∆p ∆p
psi bar
16
200 14
12
150 10
8
100
6
4
50
2
0 0 Q
0 20 40 60 80 100 120 140 l/min
Q
0 4 8 12 16 20 24 28 32 36 US gal/min
151-1409.10
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
Maximum oil flow in the drain line at a return pressure less than 5-10 bar [75-150 psi]
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
140 [2030] 20 [100] 2.5 [0.66]
35 [165] 1.5 [0.40]
210 [3050] 20 [100] 5.0 [1.32]
35 [165] 3.0 [0.79]
OMT
B A B A
151-1050.10
Mounting flange:
Standard
Shaft:
All shaft types
Mounting flange:
Wheel
Shaft:
All shaft types
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows maximum radial shaft load. Any shaft load exceeding the values shown in the
curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning in the technical information General Orbital Motors, BC152886483554.
Mounting flange:
Brake-wheel
Shaft:
All shaft types
OMT
Mounting flange:
Brake-standard
Shaft:
All shaft types
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown in the curve will
involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter Bearing
dimensioning in the technical information General Orbital Motors, BC152886483554.
Continuous range
Intermittent range (maximum 10% operation every minute)
OMT 160
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
Q=125 l/min
[33.0 US gal/min]
lbf• in Nm
5500
600
5000
550 ∆ p=240 bar
3480 psi
4500 500 N=35kW
151-493.10
OMT
OMT 200
lbf• in Nm Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
750
6500
700
6000 ∆ p=240 bar
650 35kW N=40kW 3480 psi
5500
600 30kW
5000 550 200 bar
25kW 2900 psi
4500 500 35hp
20kW 40hp
4000 450 160 bar
15kW 25hp 30hp 2320 psi
3500 400
10kW 15hp 20hp 87%
3000 350
10hp 120 bar
300
2500 N=5kW η t =88% 1740 psi
250 85%
2000
200 5hp 80 bar
1500 1160 psi
150
80%
1000 100
η t =70% ∆ p= 40 bar
500 50
580 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 min-1
(rpm)
151-494.10
OMT 250
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
lbf• in Nm
9000
8000 900
∆ p=240 bar
7000 800 3480 psi
35kW N=40kW
30kW
700 200 bar
6000
40hp 2900 psi
600 25kW 35hp
5000
20kW 30hp 160 bar
500 2320 psi
4000 15kW 25hp
400 20hp 120 bar
15hp 1740 psi
10kW
3000 η t =87%
300
N=5kW 80 bar
2000 10hp 85%
200 1160 psi
5hp 80%
1000 100 ∆ p= 40 bar
η t =70% 580 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)
151-495.10
OMT
OMT 315
lbf• in Nm
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
11000
1200
10000
1100 ∆ p=240 bar
9000 3480 psi
1000 35kW N=40kW
8000 900 200 bar
30kW
800 25kW 2900 psi
7000
40hp
700 20hp 20kW 160 bar
6000 15kW 30hp 35hp 2320 psi
15hp 25hp
600
5000
120 bar
500 10kW
4000 1740 psi
10hp
400
3000 5hp N=5kW 80 bar
300 87%
η t =88% 1160 psi
2000
200
1000
85% 80% ∆ p= 40 bar
100 580 psi
η t =70%
0 0
0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)
151-869.10
OMT 400
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
12000
1300
11000
1200 ∆ p=210 bar
10000 3050 psi
1100
9000 1000 180 bar
2610 psi
8000 900 N=30kW
25kW 150 bar
7000 800 2180 psi
20kW
700
6000 15kW 120 bar
10kW 25hp 30hp 1740 psi
600 10hp
5000 87%
20hp
500
4000 5kW
η t =89% 15hp 90 bar
5hp 1300 psi
400 85%
3000
300 60 bar
2.5hp 80% 870 psi
2000 200 N=2.5kW
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 min-1
(rpm)
151-1058.10
OMT
OMT 500
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
1500
12500
∆ p=180 bar
1250 2610 psi
0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)
151-1116.10
Intermittent pressure drop and oil flow must not occur simultaneously.
OMT
Shaft version
82 [3.23]
26 [1.02]
9.5 [0.374]
45˚
R0.5 [0.020] M12
A-A
A
Ø40.018 [1.5755]
Ø40.002 [1.5749]
43.00 [1.693]
42.71 [1.681]
Ø45 [1.77]
A C
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
R0.5 [0.020] 3/8 -16 UNC
A-A
A
Ø38.10 [1.500]
Ø38.05 [1.498]
42.40 [1.669]
42.14 [1.659]
Ø45 [1.77]
A D
57.5 [2.264] 11.5 [0.453]
56.9 [2.240] 9.3 [0.366]
9.545 [0.3758]
9.525 [0.3750]
151-1032.10
OMT
82 [3.23]
26 [1.02]
9.5 [0.374]
45˚
R0.5 [0.020] M12
A-A
A
Ø38.100 [1.5000]
Ø38.075 [1.4990]
Ø45 [1.77]
C
A
58 [2.28]
56 [2.20]
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
R0.5 [0.020] 3/8 -16 UNC
A
58 [2.28]
56 [2.20]
151-1916.10
OMT
I A-A K L
16 [0.63] A-A
H
A A
Ø56 [2.20]
Ø45 [1.77]
Ø4 [0.16]
Ø6 [0.24]
Ø7 [0.28]
Ø45 [1.77]
M30x2
24.15 [0.951]
23.95 [0.943]
E F
5.71 [0.225]
5.61 [0.221]
A J A M
34 [1.34] 4 [0.16] 32.1 [1.264]
12.000 [0.4724] 31.5 [1.240]
54 [2.13] 22 [0.87] 59.00 [2.323] 11.150 [0.4390]
11.957 [0.4707]
57.80 [2.276] 11.130 [0.4382]
82 [3.23]
4.5 [0.177]
80.8 [3.181]
80.0 [3.150]
102 [4.02]
45˚ R0.5 [0.020] R6.7 [0.267]
R5 [0.20]
60˚ A-A
A 8.6 3 [0.3
8.5
4[
Ø34.85 [1.372]
Ø34.73 [1.367]
0.3 36]
29.5 [1.161]
29.3 [1.154]
Ø45 [1.77]
40
G
]
28.14 [1.108]**
A 7 [0.28]
38.25 [1.506] 27.89 [1.098]
151-1917.10
77 [3.03] 37.75 [1.486]
75 [2.95]
OMT
B
A Ø41.5 [1.634]
Ø41.0 [1.614]
E F
min. 18 [0.67]
min. 19 [0.75]
C D
G H
min. 13 [0.51]
min. 12 [0.47]
151-1977.11
OMT
Dimensions
22.4 [0.882]
R1.6 [0.063]
9 [0.35]
32 [1.26]
31 [1.22]
60 [2.36]
72 [2.83]
18 [0.71]
64 [2.52]
L2
13.0 [0.512]
12.0 [0.472]
L
L1
D
C
13.0 [0.512]
12.0 [0.472]
max. 69 [2.72]
13.0 [0.512]
12.0 [0.472]
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
28 ]
[6. .315
3]
59 [6
Ø1 60.4
.6
R12 [0.47]
Ø1
151-889.11
OMT
Type OMT 160 OMT 200 OMT 250 OMT 315 OMT 400 OMT 500
LMax. mm 192 197 203 213 223 237
[in] [7.56] [7.76] [7.99] [8.39] [8.78] [9.33]
L1* mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 140 145 151 161 171 185
[in] [5.51] [5.71] [5.94] [6.34] [6.73] [7.28]
Weight kg 20.0 20.5 21.0 22.0 23.0 24.0
[lb] [44.1] [45.2] [46.3] [48.5] [50.7] [52.9]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMT
22.4 [0.882]
R0.8 [0.003]
9 [0.35]
31 [1.22]
60 [2.36]
73.7 [2.902]
71.5 [2.815]
18 [0.71]
64.5 [2.539]
63.5 [2.500]
L2
L
L1
max. 69 [2.72]
23.6 [0.929]
22.4 [0.882]
35 ]
[6. .390
8]
61 3 [6
R12.5 [0.492]
Ø1 62.
.5
Ø1
151-889.11.22
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
OMT
Type OMT 160 OMT 200 OMT 250 OMT 315 OMT 400 OMT 500
LMax. mm 192 197 203 213 223 237
[in] [7.56] [7.76] [7.99] [8.39] [8.78] [9.33]
L1* mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 140 145 151 161 171 185
[in] [5.51] [5.71] [5.94] [6.34] [6.73] [7.28]
Weight kg 20.0 20.5 21.0 22.0 23.0 24.0
[lb] [44.1] [45.2] [46.3] [48.5] [50.7] [52.9]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMT
Ø172.000 [6.7717]
Ø171.937 [6.7692]
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø126.25 [4.970]
Ø123.75 [4.872]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø73 [2.87]
Ø71 [2.80]
82 [3.23]
2 [0.08]x45˚
98.2 [3.866]
99 [3.90]
90.3 [3.555]
78.2 [3.079]
R1.2 [0.047]
45˚
7 [0.28]
8 [0.31]
18 [0.71]
13.0 [0.512]
12.0 [0.472]
L1
L2
R1.2 [0.047]
4 [0.16]
13.0 [0.512]
12.0 [0.472]
C
L
max. 69 [2.72]
D
13.0 [0.512]
12.0 [0.472]
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
85 ]
[7. .890
8]
99 [7
Ø1 00.4
.6
Ø2
R16 [0.63]
151-897.12
OMT
Type OMTW 160 OMTW 200 OMTW 250 OMTW 315 OMTW 400 OMTW 500
LMax. mm 126 131 137 146 157 171
[in] [4.96] [5.16] [5.39] [5.75] [6.18] [6.73]
L1* mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 73 78 84 94 104 118
[in] [2.87] [3.07] [3.31] [3.70] [4.09] [4.65]
Weight kg 22.0 22.5 23.0 24.0 25.0 26.0
[lb] [48.5] [49.6] [50.7] [52.9] [55.1] [57.3]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMT
2 [0.08]x45˚
102.1 [4.020]
99.1 [3.902]
98.2 [3.866]
90.3 [3.555]
78.6 [3.094]
77.5 [3.051]
R1.2 [0.047]
45˚
7 [0.28]
7 [0.28]
18 [0.71]
L1
L2
3.5 [0.138]
R1.2 [0.047]
C
L
max. 69 [2.72]
23.6 [0.929]
22.4 [0.882]
85 ]
[7. .890
8]
99 4 [7
Ø1 00.
.6
Ø2
R16 [0.63]
151-897.11.22
C: Drain connection, 9⁄16 - 18 UNF; 13 mm [0.51 in] deep, O-ring boss port
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMT
Type OMTW 160 OMTW 200 OMTW 250 OMTW 315 OMTW 400 OMTW 500
LMax. mm 126 131 137 146 157 171
[in] [4.96] [5.16] [5.39] [5.75] [6.18] [6.73]
L1 mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 73 78 84 94 104 118
[in] [2.87] [3.07] [3.31] [3.70] [4.09] [4.65]
Weight kg 22.0 22.5 23.0 24.0 25.0 26.0
[lb] [48.5] [49.6] [50.7] [52.9] [55.1] [57.3]
OMT
m
ax
Ø
.2
Ø1 200
32
75 [2.95]
99 .4
[9
.6 [7.8
.1
F
3]
[7 9
.8 0]
58
]
71 [2.80]
C
Ø22 [0.87]
67 [2.64]
Ø201 [7.91]
Ø180.00 [7.087] Ø120.0 [4.724]
12.2 [0.480]
11.8 [0.465]
13.2 [0.520]
12.8 [0.504]
Ø179.6 [7.074]
5.2 [0.205]
4.8 [0.189]
4.2 [0.165]
3.8 [0.150]
Ø119.6 [4.709]
H Ø95.8 [3.772] Ø76.0 [2.992]
Ø95.6 [3.764] Ø75.8 [2.984]
G
35 [1.38]
111.4 [4.386]
110.6 [4.354]
115.4 [4.543]
114.6 [4.512]
10.2 [0.402]
9.8 [0.386]
7.2 [0.283]
6.8 [0.268]
L max. 1
L max. 2
L1
E D
L2
I
13 [0.51]
12 [0.47]
11.1 [0.437]
10.9 [0.429]
23.3 [0.917]
22.7 [0.894]
13 [0.51]
12 [0.47]
23.1 [0.909]
22.9 [0.902]
20.3 [0.799] 20.3 [0.799]
19.7 [0.776] 19.7 [0.776]
22.1 [0.870] 22.1 [0.870]
21.1 [0.831] 21.1 [0.831]
100 [3.94]
128 [5.04]
Ø172.00 [6.772]
Ø171.94 [6.769]
10x36˚
5x72˚
4x90˚
151-1443.11
OMT
F:
4 × M12; 27 mm [1.06 in] deep
G: 10 × M12
Type OMT 160 FX OMT 200 FX OMT 250 FX OMT 315 FX OMT 400 FX OMT 500 FX
LMax. 1 mm 225 230 236 245 256 270
[in] [8.86] [9.06] [9.29] [9.65] [10.08] [10.63]
LMax. 2 mm 228 234 240 249 260 274
[in] [8.98] [9.21] [9.45] [9.80] [10.24] [10.79]
L1* mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 62 67 74 83 93 107
[in] [2.45] [2.65] [2.89] [3.26] [3.67] [4.22]
Weight kg 31.0 31.5 32.0 33.0 34.0 35.0
[lb] [68.3] [69.4] [70.5] [72.8] [75.0] [77.2]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMT
31.5 [1.240]
82 [3.23]
R1.6 [0.063]
12 [0.47]
18 [0.71]
60 [2.36]
32 [1.26]
104 [4.09]
85.8 [3.378]
90.5 [3.563]
E L2
L
D
F
L1
13.0 [0.512]
12.0 [0.472]
C
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
13.0 [0.512]
12.0 [0.472]
13.0 [0.512]
12.0 [0.472]
151-1453.10
OMT
Type OMT 160 OMT 200 OMT 250 OMT 315 OMT 400 OMT 500
FL/FH FL/FH FL/FH FL/FH FL/FH FL/FH
LMax. mm 230 233 241 250 261 275
[in] [9.06] [9.17] [9.49] [9.84] [10.28] [10.83]
L1* mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 178 183 189 199 209 223
[in] [7.01] [7.20] [7.44] [7.83] [8.23] [8.78]
Weight kg 24.5 25.0 25.5 26.5 27.5 28.5
[lb] [54.0] [55.1] [56.2] [58.4] [60.6] [62.8]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
Ø124.937 [4.9188]
8 [0.31]
R1 [0.04]
Ø14 [0.55]
22 [0.87]
31 [1.22]
18 [0.71]
L2
13 [0.512]
12 [0.472]
L1
8 [0.31]
C
13 [0.512]
12 [0.472]
L
max. 69 [2.72]
13 [0.512]
12 [0.472]
D
23.6 [0.926]
22.4 [0.882]
13 [0.512]
12 [0.472]
Ø16
Ø15 0.4 [6.3
9.6 1
[6.2 5]
83]
Ø6 [0.24]
151-898.11
OMT
Type OMTS 160 OMTS 200 OMTS 250 OMTS 315 OMTS 400 OMTS 500
LMax. mm 146 151 157 166 177 191
[in] [5.75] [5.94] [6.18] [6.54] [6.97] [7.52]
L1 mm 16.5 21.5 27.8 37.0 47.5 61.5
[in] [0.650] [0.846] [1.094] [1.457] [1.870] [2.421]
L2 mm 96 101 107 116 127 142
[in] [3.78] [3.98] [4.21] [4.57] [5.00] [5.59]
Weight kg
[lb]
Type Lmax L1 L2
OMTS 500
OMTS
Installation
The cardan shaft of the OMTS motor acts as an “output shaft”. Because of the movement of the shaft, no
seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.
During start and operation it is important that the spline connection and the bearings in the attached
component receive oil and are adequately lubricated. To ensure that the spline connection receives
sufficient oil, a conical sealing ring between the shaft of the attached component and the motor
intermediate plate is recommended. This method is used in the OMT.
The conical sealing ring (code. no. 633B9022) is supplied with the motor.
To ensure that oil runs to the bearings and other parts of the attached component, the stop plate must
have a hole in it (see fig. below).
We recommend an O-ring between motor and attached component. The O-ring (code no. 151B1040) is
supplied with the motor. If motor and attached component have been separated, remember to refill
before starting up. Fill the oil through the drain connection.
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMT
K 0.25 [0.010]
Ø88.5 [3.484]
Ø87.5 [3.445]
K 0.1˚
Ø125.063 [4.9237]
Ø125.000 [4.9212]
Ø133.0 [5.236]
Ø132.6 [5.220]
min. Ø55 [2.17]
Ø53.5 [2.106]
Ø53.5 [2.098]
min. Ø6 [0.24]
Ø63.5 [2.500]
Ø62.5 [2.461]
K
39.5 [1.555]
38.5 [1.516]
Ø51.5 [2.028]
Ø50.5 [1.988]
G
H D
E
2.5 [0.098] min. 5 [0.2] 8.2 [0.323]
1.5 [0.059] 7.8 [0.307]
18.5 [0.728]
25.5 [1.004] 17.5 [0.689]
24.5 [0.965]
11.4 [0.449] 30 [1.181]
11.0 [0.433] 29 [1.142]
46.3 [1.823]
45.7 [1.799]
69.4 [2.732]
68.6 [2.701]
151-452.10
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4 (900 N/mm2) or SAE
8620.
OMT
Hardening specification:
• On the surface: HV = 750 ± 50
• 0.7 ± 0.2 mm under the surface: HV = 560
Internal involute spline data; Standard ANS B92.1-1970, class 5 (corrected m · X = 1; m = 2.1166)
Flat root side fit mm in
Number of teeth z 16 16
Pitch DP 12/24 12/24
Pressure angle 30° 30°
Pitch dia. D 33.8656 1.3333
Major dia. Dri 38.40 +0.4 1.51180+0.0157
Form dia. (min.) Dfi 37.6 1.4803
Minor dia. Di 32.1500 + 0.04 1.26570+ 0.00157
Space width (circular) Lo 4.516±0.037 0.1777±0.0014
Tooth thickness (circular) So 2.170 0.0854
Fillet radius Rmin. 0.5 0.02
Max. measurement between pins* l 26.90 + 0.1 1.0590+0.004
Pin dia. d 4.834±0.001 0.1903±0.00004
* Finished dimensions (when hardened).
Rmin
Lo
So
l d
Dri
Di
Dfi
D
151-455.10
This section shows the different versions/configuration codes and the ordering numbers.
• Section OMT technical data, specify the technical data for OMT for each shaft type.
• In section OMT function diagrams, the diagram for each motor size is shown.
• See OMT dimensions for outer main dimensions for the different OMT motor types.
This section shows the different versions/configuration codes and the ordering numbers.
• Section OMV technical data on page 40, specify the technical data for OMV for each shaft type.
• In section OMV function diagrams on page 45, the diagram for each motor size is shown.
• See OMV dimensions on page 53 for outer main dimensions for the different OMV motor types.
OMV features
Features available (options):
• Speed sensor
• Motor with tacho connection
• Viton shaft seal
• Painted
• Ultra short
2) Peak load: The permissible values may occur for max. 1% of every minute.
2) Peak load: The permissible values may occur for max. 1% of every minute.
For maximum permissible combination of flow and pressure, see OMV function diagrams on page 45 for
actual motor.
151-320.10
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)
151-1674.10
– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation
∆p ∆p
psi bar
16
200 14
12
150 10
8
100
6
4
50
2
0 0 Q
0 20 40 60 80 100 120 140 160 180 200 l/min
Q
0 5 10 15 20 25 30 35 40 45 50 US gal/min
151-1410.10
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
Maximum oil flow in the drain line at a return pressure less than 5-10 bar [75-150 psi]
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
140 [2030] 20 [100] 3.0 [0.79]
35 [165] 2.0 [0.53]
Maximum oil flow in the drain line at a return pressure less than 5-10 bar [75-150 psi] (continued)
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
210 [3050] 20 [100] 6.0 [1.59]
35 [165] 4.0 [1.06]
Shaft:
All shaft types
Prad. Prad.
lbf N
16000 70000
0 Pmax. =15000 N
- +
14000 =3372 lbf
60000
12000
50000
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm
151-1973.10
Shaft:
All shaft types
Prad. Prad.
lbf N
16000 70000
0 Pmax. =15000 N
- +
14000 =3372 lbf
60000
12000
50000
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
0 20 40 60 80 100 120 140 160 180 200 mm
0 1 2 3 4 5 6 7 in
151-1969.10
Shaft:
All shaft types
Prad. Prad.
lbf N
14000
60000
0 Pmax. =10000 N
12000 A B
- +
=2248 lbf
50000
10000 B
40000
8000 A
30000
6000
20000
4000
2000 10000
0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm
151-1965.10
Explanation of function diagram use, basis and conditions can be found in Speed, torque, and output on
page 7.
Continuous range
Intermittent range (max. 10% operation every minute)
Maximum permissible continuous/intermittent pressure drop for the actual shaft version can be found in
OMV technical data on page 40.
Intermittent pressure drop and oil flow must not occur simultaneously.
25 l/min
[6.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
160 l/min
[42.2 US gal/min]
Q=200 l/min
[52.8 US gal/min]
lbf• in N• m
11000
1200
10000
1100
∆ p=240 bar
9000 1000 3480 psi
8000 N=50kW
900
200 bar
7000 800 2900 psi
170 bar
40kW
700 30kW 2540 psi
6000 30hp
50hp
600 140 bar
5000 20kW
20hp 40hp 2030 psi
500
4000 10kW η t =87%
N=5kW 105 bar
400 10hp
5hp 1520 psi
3000 85%
300
70 bar
2000 1020 psi
200
80%
1000 100 η t =70% ∆ p= 35 bar
510 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 min-1
(rpm)
151-870.11
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
175 l/min
[46.2 US gal/min]
200 l/min
[52.8 US gal/min]
Q=240 l/min
[63.4 US gal/min]
lbf• in N• m
14000 1600
1400
12000 ∆ p=240 bar
3480 psi
1200
10000
200 bar
1000 N=50kW 2900 psi
30hp 50hp 175 bar
8000
40hp 40kW 2540 psi
800
20hp 140 bar
6000 30kW 2030 psi
600
η t =88% 87%
105 bar
10hp 20kW
4000 85% 1520 psi
400
5hp 10kW 70 bar
N=5kW 80% 1020 psi
2000 200
η t =70% ∆ p= 35 bar
510 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)
151-871.11
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
175 l/min
[46.2 US gal/min]
200 l/min
[52.8 US gal/min]
Q=240 l/min
[63.4 US gal/min]
16000 1800
0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)
151-872.11
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=240 l/min
[63.4 US gal/min]
150 l/min
[39.6 US gal/min]
175 l/min
[46.2 US gal/min]
200 l/min
[52.8 US gal/min]
lbf• in N• m
17500 2000
1750
∆ p=210 bar
15000 N=60kW 3050 psi
1000 40hp
20kW 120 bar
η t =89% 30hp 1740 psi
7500
750 10kW
87% 90 bar
N=5kW 20hp 1300 psi
5000
500
85% 60 bar
80% 10hp 870 psi
2500 250
η t =70% 5hp ∆ p= 30 bar
440 psi
0 0
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 min-1
(rpm)
151-879.11
Q = 10 l/min
2.6 US gal/min
25 l/min
6.6 US gal/min
50 l/min
13.2 US gal/min
75 l/min
19.8 US gal/min
100 l/min
26.4 US gal/min
125 l/min
33.0 US gal/min
150 l/min
39.6 US gal/min
175 l/min
46.2 US gal/min
200 l/min
52.8 US gal/min
Q = 240 l/min
63.4 US gal/min
20000 2250
0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)
P301 250.11
Shaft version
Ø50.018 [1.9692]
Ø50.002 [1.9686]
53.5 [2.106]
53.2 [2.094]
Ø60 [2.36]
A
70.5 [2.776] 5.5 [0.217] 14.000 [0.5512]
70.0 [2.756] 4.5 [0.177] 13.957 [0.5495]
79 [3.11] D
151-878.12_A
A: Cylindrical 50 mm shaft
D: Parallel key
A14 × 9 × 70; DIN 6885
Keyway deviates from standard
82.2 [3.236]
81.8 [3.220]
min. 20
[0.78]
60˚ R0.5 [0.020] 3/8 -16 UNC A-A
A
Ø57.15 [2.250]
Ø57.10 [2.248]
62.92 [2.477]
62.66 [2.467]
Ø60 [2.36]
A
13.1 [0.516] 12.73 [0.501]
10.9 [0.429] 12.70 [0.500]
E
57.5 [2.264]
56.9 [2.240]
151-878.12_B
E: Parallel key
1/2 × 1/2 × 21/4 in; B.S. 46
Keyway deviates from standard
Shaft version
99.2 [3.906]
98.8 [3.890]
min. 26
[1.02]
½ -20 UNF
60˚ R0.5 [0.020] A-A
A
57.15 [2.250]
57.10 [2.248]
62.93 [2.478]
62.66 [2.467]
Ø60 [2.36]
C
A
70.4 [2.772]
70.2 [2.763] 12.73 [0.501]
12.70 [0.500] F
151-878.12_C
F Parallel key
1/2 × 1/2 × 21/4 in; B.S. 46
Keyway deviates from standard
82[3.23]
26 [1.02]
A
58 [2.28]
56 [2.20]
151-1918.10_D
Shaft version
US version
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
3/8 -16 UNC
R0.5 [0.020] A-A
A
Ø53.975 [2.1250]
Ø53.950 [2.1240]
Ø60 [2.36]
A
57 [2.24]
55 [2.17]
151-1918.10_E
E: Involute splined shaft for OMV with standard mounting flange ANS B92.1 - 1996 standard
Flat root side fit
Pitch 8/16; Teeth 16
Major dia. 2.125 in
Pressure angle 30°
US version
76.9 [3.028]
76.5 [3.011]
min. 26 [1.02]
½ -20 UNF
30˚ R0.5 [0.020]
A-A
A
Ø53.972 [2.1249]
Ø53.954 [2.1242]
Ø60 [2.36]
A
56.3 [2.217]
55.3 [2.177]
151-1918.10_F
F: Involute splined shaft for OMV with mounting flange SAE-C ANS B92.1 - 1996 standard
Flat root side fit
Pitch 8/16; Teeth 16
Major dia. 2.125 in
Pressure angle 30°
Shaft version
23 [0.91]
7 [0.28]
A-A
I J
A
M42x3 [0.12]
Ø8 [0.31]
Ø9 [0.35]
Ø60 [2.36]
Ø78 [3.07]
G
32.25 [1.270]
32.05 [1.262]
A
40.5 [1.594] 6 [0.24]
40.0 [1.575] 16.000 [0.6299] K
70 [2.76] 15.957 [0.6282]
105 [4.13]
151-1919.10_G
G: Tapered 60 mm shaft
J: DIN 937
Across flats: 65 mm
Tightening torque: 750 ±50 N•m [6640 ±440 lbf•in]
I: Taper 1:10
16 [0.63]
45˚
L 4.5 [0.177]
M A-A
A
Ø57.20 [2.252]
Ø57.10 [2.248]
Ø4 [0.16]
Ø60 [2.36]
H
7.29 [0.287]*
7.19 [0.283]
A
51.1 [2.012] 14.308 [0.5633]
50.5 [1.988] 14.288 [0.5625]
73.6 [2.898] N
72.4 [2.850]
100.4 [3.953]
99.6 [3.921]
151-1919.10_H
L: Cone 1:8
SAE J501
M: 11/2 - 18 UNEF
Across flats: 2 3/8 in
Tightening torque: 750 ±50 N•m [6640 ±440 lbf•in]
N: Parallel key
9/16 × 9/16 × 2 in
Shaft version
B.S. 46
Keyway deviates from standard
A
A: G main ports
E
E: ISO 228/1 - G1
min. 18 [0.67]
151-1977.11_A
B
B: UN main ports
Ø41.5 [1.634]
Ø41.0 [1.614] F: 1 5/16 - 12 UN O-ring boss port
F
min. 19 [0.75]
151-1977.11_B
C
C: G drain port
G G: ISO 228/1 - G1/4
min. 12 [0.47]
151-1977.11_C
D
D: UNF drain port
H H: 9/16 - 18 UNF O-ring boss port
min. 13 [0.51]
151-1977.11_D
OMV dimensions
2 [0.08]x45˚
11 [0.43]
39.4 [1.551]
38.6 [1.520]
40 [1.57]
33˚
R1.6 [0.063]
60 [2.36]
20 [0.79]
C
L2
69 [2.72] 8 [0.31]
E
14.0 [0.551]
13.0 [0.512]
L1
L
14.0 [0.551]
13.0 [0.512]
max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]
14.0 [0.551]
13.0 [0.512]
0]
89 ]
[7. 58
.4 [7.8
max. 181.3 [7.14]
0 0
Ø2 199.6
Ø
Ø18 [0.71]
R16 [0.63] max. 181.3 [7.14]
151-890.12
OMV dimensions
Type OMV 315 OMV 400 OMV 500 OMV 630 OMV 800
LMax. mm [in] 216 [8.50] 223 [8.78] 231 [9.09] 242 [9.53] 256 [10.08]
L1* mm [in] 22.0 [0.866] 29.0 [1.142] 37.0 [1.457] 47.5 [1.870] 61.5 [2.421]
L2 mm [in] 160 [6.30] 167 [6.57] 175 [6.89] 186 [7.32] 200 [7.87]
Weight kg [lb] 31.8 [70.1] 32.6 [71.9] 33.5 [73.9] 34.9 [76.9] 36.5 [80.5]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMV dimensions
2 [0.08]x45˚
L3
33˚
R1.2 [0.047]
10 [0.39]
79 [3.11]
22 [0.87]
8 [0.31]
20 [0.79]
13.0 [0.512]
C
L
max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]
14.0 [0.551]
13.0 [0.512]
1]
83 ]
[8. 07
4.3 [8.8
2 7
Ø18 [0.71]
R16 [0.63] max. 200 [7.87]
151-899.12
OMV dimensions
Type OMV 315 OMV 400 OMV 500 OMV 630 OMV 800
LMax. mm [in] 148 [5.83] 155 [6.10] 163 [6.42] 174 [6.85] 188 [7.40]
L1* mm [in] 22.0 [0.866] 29.0 [1.142] 37.0 [1.457] 47.5 [1.870] 61.5 [2.421]
L2 mm [in] 92 [3.62] 99 [3.90] 107 [4.21] 118 [4.65] 132 [5.20]
Weight kg [lb] 32.4 [71.4] 33.2 [73.2] 34.1 [35.5] 35.5 [78.3] 37.1 [81.8]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
Ø14 [0.55]
22 [0.87]
R1 [0.04]
20 [0.79]
35 [1.38]
82 [3.23]
L2
8 [0.31]
14.0 [0.551]
13.0 [0.512]
L1
C
14.0 [0.551]
13.0 [0.512]
L
max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]
14.0 [0.551]
13.0 [0.512]
Ø180
28 [1.10]
5
]
Ø179 .4 [7.102
.6 [7.0 ]
71]
151-900.11
OMV dimensions
Type OMV 315 OMV 400 OMV 500 OMV 630 OMV 800
LMax. mm [in] 173 [6.81] 180 [7.09] 188 [7.40] 199 [7.83] 213 [8.39]
L1* mm [in] 22.0 [0.866] 29.0 [1.142] 37.0 [1.457] 47.5 [1.870] 61.5 [2.421]
L2 mm [in] 117 [4.61] 124 [4.88] 132 [5.20] 143 [5.63] 157 [6.18]
Weight kg [lb] 22.7 [50.1] 23.5 [78.3] 24.4 [53.8] 25.6 [56.4] 27.2 [61.1]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMV dimensions
2 [0.08]x45˚
11 [0.43]
39.4 [1.551]
38.6 [1.520]
40 [1.57]
33˚
R1.6 [0.063]
60 [2.36]
20 [0.79]
77 [3.03]
L2
C 69 [2.72]
D
L1
L
max. 76 [2.99]
24.6 [0.969]
23.4 [0.921]
0]
89 ]
[7. 58
.4 [7.8
max. 181.3 [7.14]
0
0 6
Ø2 199.
Ø
Ø18 [0.71]
R16 [0.63] max. 181.3 [7.14]
151-890.12.22
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
OMV dimensions
Type OMV 315 OMV 400 OMV 500 OMV 630 OMV 800
LMax. mm [in] 216 [8.50] 223 [8.78] 231 [9.09] 242 [9.53] 256 [10.08]
L1* mm [in] 22.0 [0.866] 29.0 [1.142] 37.0 [1.457] 47.5 [1.870] 61.5 [2.421]
L2 mm [in] 160 [6.30] 167 [6.57] 175 [6.89] 186 [7.32] 200 [7.87]
Weight kg [lb] 31.8 [70.1] 32.6 [71.9] 33.5 [73.9] 34.9 [76.9] 36.5 [80.5]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMV dimensions
L3
16.1 [0.634]
13.7 [0.539]
13.8 [0.543]
13.2 [0.520]
21.0 [0.827]
19.6 [0.772]
85.5 [3.366]
C 71.0 [2.795]
L2
81.5 [3.209]
L
L1
24.0 [0.945]
max. 76 [2.99]
D
0]
39
3 [6. .358]
.
62 [6
Ø1 61.5
max. 147 [5.79]
Ø1
Ø17.7 [0.697]
Ø17.3 [0.681]
max. 147 [5.79]
151-1485.11
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
OMV dimensions
Type OMV 315 OMV 400 OMV 500 OMV 630 OMV 800
LMax. mm [in] 240 [9.45] 247 [9.72] 255 [10.04] 266 [10.47] 280 [11.02]
L1* mm [in] 22.0 [0.866] 29.0 [1.142] 37.0 [1.457] 47.5 [1.870] 61.5 [2.421]
L2 mm [in] 185 [7.28] 192 [7.56] 200 [7.87] 211 [8.31] 225 [8.86]
Weight kg [lb] 30.0 [66.2] 30.8 [67.9] 31.7 [69.9] 33.1 [73.0] 34.7 [76.5]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMV dimensions
33˚
R1.2 [0.047]
10 [0.39]
79 [3.11]
22 [0.87]
8 [0.31]
20 [0.79]
R1.2 [0.047]
L1
3.6 [0.142]
L2
C
L
max. 76 [2.99]
24.6 [0.969]
23.4 [0.921]
1]
83 ]
3 [8. .807
.
24 [8
max. 200 [7.87]
Ø2 223.7
Ø
Ø18 [0.71]
R16 [0.63] max. 200 [7.87]
151-899.12.22
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
OMV dimensions
Type OMV 315 OMV 400 OMV 500 OMV 630 OMV 800
LMax. mm [in] 148 [5.83] 155 [6.10] 163 [6.42] 174 [6.85] 188 [7.40]
L1* mm [in] 22.0 [0.866] 29.0 [1.142] 37.0 [1.457] 47.5 [1.870] 61.5 [2.421]
L2 mm [in] 92 [3.62] 99 [3.90] 107 [4.21] 118 [4.65] 132 [5.20]
Weight kg [lb] 32.4 [71.4] 33.2 [73.2] 34.1 [35.5] 35.5 [78.3] 37.1 [81.8]
* The gearwheel set is 3.5 mm [0.138 in] wider across the rollers than the L1 dimensions
OMVS
K 0.25 [0.010]
6 [0.24]
K 0.1˚ R
min. Ø60 [2.36]
4 [0.16]
Ø140.063 [5.5143]
Ø140.000 [5.5118]
Ø147.9 [5.823]
Ø147.7 [5.815]
Ø61.2 [2.409]
Ø61.0 [2.402]
Ø102 [4.02]
Ø100 [3.94]
Ø71 [2.80]
Ø69 [2.72]
K
Ø46.2 [1.819]
Ø45.8 [1.803]
Ø56.3 [2.217]
Ø55.5 [2.165]
G E
H max. 2 [0.08] min. 5 [0.2]
8.4 [0.331]
7.6 [0.299] 20.5 [0.807]
9.5 [0.374]
19.5 [0.768]
8.5 [0.335]
32.5 [1.280] 28.7 [1.130]
31.5 [1.240] 26.3 [1.035]
53.3 [1.098]
52.7 [2.075]
76.3 [3.004]
75.7 [2.980]
151-815.11
A: O-ring: 140 × 3 mm
OMVS
Material
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4 (900 N/mm2) or SAE
8620.
Hardening specification
• On the surface: HV = 750 ± 50
• 0.7 ± 0.2 mm under the surface: HV = 560
Internal involute spline data; Standard ANS B92.1-1996, class 5 (corrected m · X = 1; m = 2.54)
Flat root side fit mm [in]
Number of teeth z 16
Pitch DP 10/20
Pressure angle 30°
Pitch diameter D 40.640 [1.6]
Major diameter Dri 45.20+0.4 [1.7800+0.016]
Form diameter (minimum) Dfi 44.6 [1.756]
Minor diameter Di 38.50 + 0.039 [1.5160+ 0.0015]
Space width (circular) Lo 5.180 ±0.037 [0.204 ±0.0015]
Tooth thickness (circular) So 2.835 [0.1116]
Fillet radius Rmin. 0.4 [0.015]
Maximum measurement between pins* l 32.470+ 0.15 [1.2780+0.006]
Pin diameter d 5.6 ±0.001 [0.22 ±0.00004]
* Finished dimensions (when hardened)
Rmin
Lo
So
Dri
Di
l d Dfi
D
151-816.10
OMVS
The drain line must be led to the tank in such a way that there is no risk of the motor and attached
component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its shaft seal.
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Danfoss
Power Solutions Trading
Danfoss Danfoss Danfoss (Shanghai) Co., Ltd.
Power Solutions (US) Company Power Solutions GmbH & Co. OHG Power Solutions ApS Building #22, No. 1000 Jin Hai Rd
2800 East 13th Street Krokamp 35 Nordborgvej 81 Jin Qiao, Pudong New District
Ames, IA 50010, USA D-24539 Neumünster, Germany DK-6430 Nordborg, Denmark Shanghai, China 201206
Phone: +1 515 239 6000 Phone: +49 4321 871 0 Phone: +45 7488 2222 Phone: +86 21 2080 6201
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.