Professional Documents
Culture Documents
Incorporating National Amendment No.1
Incorporating National Amendment No.1
National
Incorporating
Amendment No.1
NA to BS EN 1992-1-1:2004
Summary of pages
This National Annex was
published under the authority This document comprises a front cover, an inside front cover, pages i, a
of the Standards Policy and
Strategy Committee on blank page, pages 1 to 20, an inside back cover and a back cover.
8 December 2005
The BSI copyright notice displayed in this document indicates when
the document was last issued.
© BSI 2009
© BSI 2009
Table deleted
Table deleted
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
© BSI 2009
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
¼ ¼
¼
¼
³
³
º
º
© BSI 2009
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
© BSI 2009
º
º
º
# ¼
#
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
¼ ¼
¼ ¼ ¼
¼ ¼
¼ ¼ ¼
¼
¼
Ø
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
© BSI 2009
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
© BSI 2009
N
º
º
º
Ø
Ä Ä µ µ µ
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
#Ô ´
#Ô ´ 8
´ N ´
¼# ¼# ¼#
¼#
Ç Ç
Ø N ØN N ØN
Ø
!1,25".
© BSI 2009
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
© BSI 2009
Ç ³ Ç Ç !ν1=ν(1−0,5cosα)"
³ Ç ³ N
Ç ³ 8
³
Ô Ô N
Ô N
Ô Ô
Ô
Ø
Ç ³
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
Ø N Ø N
N Ø N
´ ´
´
´
¼
!νRd,max=0,5νfcd νRd,max=0,5νfcd
In addition, νEd should be limited to 2νRdc at the first
control perimeter"
!k=1,5
Unless the perimeter at which reinforcement is no longer
required is less than 3d from the face of the loaded area/
column. In this case the reinforcement should be placed
in the zone 0,3d and 1,5d from the face of the loaded
area/column. The first perimeter of reinforcement should
be no further than 0,5d from the face of the loaded area/
column."
Ç Ç
¼ ¼
© BSI 2009
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
© BSI 2009
Ô
Ê
ÊÔ N
Ê Ê
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
´ ´
Ò
³
N
Ê Ê
© BSI 2009
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
© BSI 2009
EurocodeA) recommendation
EurocodeA) recommendation
Ê
Ê
Ê
Ê
!Values of Ac and As,bpmin Ac from Table 9.6N"
© BSI 2009
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
© BSI 2009
8
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
³ ³ ³ ³
³ !αct,pl = 0,8"
¼
¼
¼ ¼ ¼
¼
¼
» ¼ »
¼
´
´
º
º
º
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
© BSI 2009
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
EurocodeA) recommendation
© BSI 2009
Ø N ØN
!A) Table NA.1 relates to BS EN 1992-1-1 incorporating Corrigendum No. 1 (January 2008)."
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
16
!Tables deleted."
© BSI 2009
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
!In BS EN 1992-1-1:2004, Expression (7.11) the cover, c should be taken as cnom. The use of the
resulting value of sr,max in BS EN 1992-1-1:2004, Expression (7.8) will then provide an estimation of
the crack width at the surface of the concrete. In some situations, such as structures cast against the
ground, cnom will be significantly greater than the cover required for durability. Where there are no
appearance requirements it is reasonable to determine the crack width at the cover required for
durability and verify that it does not exceed the relevant maximum crack width.
This may be done by multiplying the crack width determined at the surface by (cmin,dur + ∆cdev)/cnom to
give the crack width at the cover required for durability, and verifying that it is not greater than
wmax. This approach assumes the crack width varies linearly with zero width at the face of the bar."
© BSI 2009 17
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
Ò Ò
!NOTE 4 The values of k in the table might not be appropriate when the form-work is struck at an early age or when the
construction loads exceed the design load. In these cases, the deflections may need to be calculated using advice in specialist
literature, e.g. the Concrete Society’s report on deflecions in concrete slabs and beams and an article for the Magazine of
Concrete Research entitled Are existing span to depth rules conservative for flat slabs?, both of which are referenced in NA.4.
NOTE 5 When the span/depth ratio obtained from NA.3 or Expressions (7.16a) or (7.16b) is adjusted using either (310/σs) or
(500/fyk)(As,prov/As,req), such adjustment should be limited to a maximum value of 1.5. σs should be calculated under characteristic
combination of load at serviceability limit state.
NOTE 6 The absolute value of span/depth may not, in any case, exceed 40K."
18 © BSI 2009
Ê Ê
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
N Ê
Ê
Ê
Ê
Ê
N Ê
Ê Ê ÊN
Ê ÊN
© BSI 2009 19
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
![1] GREAT BRITAIN. The Building Regulations 2000. London: The Stationery Office.
[2] GREAT BRITAIN. The Building Regulations 2000 Approved Document A: Structure. London: The
Stationery Office, 2004.
[3] GREAT BRITAIN. Building (Scotland) Regulations 2004, as amended: The Stationery Office.
[4] GREAT BRITAIN. The Scottish Building Standards Technical Handbook Domestic: The Stationery
Office.
[5] GREAT BRITAIN. The Scottish Building Standards Technical Handbook Non-Domestic: The
Stationery Office.
[6] GREAT BRITAIN. Building Regulations (Northern Ireland) 2000. Belfast: The Stationery
Office."
20 © BSI 2009
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
BSI - British Standards Institution
BSI is the independent national body responsible for preparing British
Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of British
Standards should make sure that they possess the latest amendments or
Licensed copy: Southampton University User, University of Southampton, Version correct as of 19/09/2011 10:23, (c) BSI
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover. Tel:
+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996
7001 Email: orders@bsigroup.com You may also buy directly using a debit/credit
card from the BSI Shop on the Website http://www.bsigroup.com/shop
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which
give details on all its products and services. Contact Information Centre. Tel:
+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: info@bsigroup.com
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration. Tel: +44 (0)20
8996 7002 Fax: +44 (0)20 8996 7001 Email: membership@bsigroup.com
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsigroup.com/BSOL
Further information about BSI is available on the BSI website at http://
www.bsigroup.com
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may
be reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
BSI Group permission from BSI.
Headquarters 389 This does not preclude the free use, in the course of implementing the standard,
Chiswick High Road, of necessary details such as symbols, and size, type or grade designations. If
London, W4 4AL, UK these details are to be used for any other purpose than implementation then the
Tel +44 (0)20 8996 9001 prior written permission of BSI must be obtained.
Fax +44 (0)20 8996 7001
www.bsigroup.com/ Details and advice can be obtained from the Copyright and Licensing Manager.
standards Tel: +44 (0)20 8996 7070 Email: copyright@bsigroup.com