Professional Documents
Culture Documents
Caller ID/MFC Features and Specifications: NEC America, Inc
Caller ID/MFC Features and Specifications: NEC America, Inc
ISSUE 3
Caller ID/MFC
Features and Specifications
FEBRUARY, 2003
Copyright 2003
NEC Corporation
7-1, Shiba 5-chome
Minato-ku, Tokyo 108-8001
Japan
Printed in Japan
ND-91638-006(E)
Table of Contents
Table of Features.....................................................................................................................iii
Introduction .............................................................................................................................iv
CALLER ID CLASS ...................................................................................................................1
CALLER ID - STATION .............................................................................................................3
MFC INCOMING CALL..............................................................................................................5
MFC OUTGOING CALL ............................................................................................................7
ND-91638-006(E) Page i
Issue 3
This page is for your notes.
Page ii ND-91638-006(E)
Issue 3
Table of Features
Page iv ND-91638-006(E)
Issue 3
CALLER ID CLASS
GENERAL DESCRIPTION
This feature receives the calling subscriber’s name and number sent from a public network using a
MODEM signal. It displays the name or number on LCD of a Dterm or an Attendant Console.
STATION APPLICATION
All Dterms with LCD
DESK CONSOLE
SMART CONSOLE
OPERATING PROCEDURE
To display the calling subscriber’s name or number when receiving/answering a call
No manual operation is required.
In case of receiving both the name and the number, system programming can specify which one has
priority for display.
SERVICE CONDITIONS
1. Up to 14 digits of the calling subscriber’s name or number can be displayed on the LCD of a Dterm or
an Attendant Console.
2. Up to 16 digits of the calling subscriber’s number can be recorded on the SMDR.
3. Up to 24 digits of the calling subscriber’s number can be sent to the OAI computer.
4. The 4RSTC card and the 4COTG/8COTQ card are required for receiving the Caller ID signals.
5. In case of receiving a subscriber’s name that differs from the name assigned by system programming,
system programming can specify which name has priority.
6. The kind of the ringing tone can be assigned to each calling subscriber’s number respectively.
ND-91638-006(E) Page 1
Issue 3
CALLER ID CLASS (CONT’D)
SERVICE CONDITIONS (CONT’D)
7. The destination station in the Day Mode/Night Mode can be specified for each calling subscriber’s
number.
8. The priority for queuing (when the destination station belongs to an UCD group and all the stations are
busy) can be set by each calling subscriber’s number.
9. It can be specified whether Call Waiting is set or not by each calling subscriber’s number.
10. Table 0 in CMDC YY = 00-63 is reserved for incoming numbers not programmed in the system.
Page 2 ND-91638-006(E)
Issue 3
CALLER ID - STATION
GENERAL DESCRIPTION
This feature enables analog telephones to connect with Caller ID display function, and provides the calling
party’s number and name on the display without answering incoming calls.
The following information is indicated according to the kind of the calls.
STATION APPLICATION
All analog telephones with Caller ID display function
OPERATING PROCEDURE
No manual operation is required.
SERVICE CONDITIONS
1. A FP is required on PIM0.
2. Following hardware is required.
--- PN - 4RSTF (Sender)
--- PN - 4LLCB (LC)
--- PN - PW122 (-48V DC power supply)
3. PN - 4RSTF and PN - 4LLCB cannot be mounted on remote PIM.
ND-91638-006(E) Page 3
Issue 3
CALLER ID - STATION (CONT’D)
SERVICE CONDITIONS (CONT’D)
4. Maximum of four PN - 4RSTF cards can be accommodated. (Maximum of 16 senders can be accom-
modated because there are 4 circuits per card.)
The maximum of 16 calls is available at the same time. However, the number of calls set in CM42 (1st
data=02)has priority over the maximum number of simultaneous calls.
5. If all senders are busy, calls will be in progress without displaying calling number and name.
6. When a caller uses a Dterm, station number of the seized line will be sent as the calling party number.
7. When a caller uses a Dterm, name display can select either of My line or of seized line, by system data
programming.
8. When a call is transferred by Consultation Hold, the display shows the information of the held station/
trunk.
9. When a call is terminated by recall (recall bvy Call Transfer, Call Park, etc.), the display shows the in-
formation of the held station/trunk.
10. If there is no calling party number to be sent, displaying Caller-ID will be controlled by sender. Reason
for Absence of DN (out of area/unavailable(4F)) will be sent this time.
• Automatic wake up/Timed Reminder
• Recall of Trunk Queuing - Outgoing
11. Ring back tone is fixed to be 2 seconds-on and 4 seconds-off. The system data set for other ringing tone
sending patterns is ineffective.
Immediate ringing is restricted. If immediate ringing is set, it will be ineffective.
12. One hit ringer of Call forwarding-All calls should be restricted by any of following system data.
• CM08 1st Dat = 266
2nd Data = 0: restricted (default is 1: allowed)
• CM15•YY=81 1st Data = Service Restriction Class C
2nd Data = 0: restricted (default is 1: allowed)
Page 4 ND-91638-006(E)
Issue 3
MFC INCOMING CALL
GENERAL DESCRIPTION
This feature allows the system to receive an incoming call from the C.O. with the MFC signaling.
STATION APPLICATION
Not applicable
OPERATING PROCEDURE
No manual operation is required.
SERVICE CONDITIONS
1. The system can receive maximum of 6 digits from C.O. as a station number. If required, the system can
convert the received digits to station number by adding and/or deleting the number of digit(s) after the
reception of digits from the C.O. Maximum 2 digits can be added or deleted.
2. If the called station is busy or no answer, the incoming call is routed to the Attendant, predesignated
station or announcement by system data programming.
3. If the system receives the invalid number (non-existing station number etc.), the incoming call is
routed to the Attendant, predesignated station or announcement by the system data programming.
4. The following service features are available for MFC incoming calls.
• CALL FORWARDING-ALL CALLS/BUSY LINE/DON’T ANSWER
• CALL FORWARDING-OUTSIDE (ALL CALLS/BUSY LINE/DON’T ANSWER)
• CALL PICK UP-DIRECT/GROUP
• DO NOT DISTURB
• STATION HUNTING
• UCD
• DELAY ANNOUNCEMENT-UCD
• OVERFLOW-UCD
• OVERFLOW ANNOUCEMENT-UCD
• CALL WAITING
• TENANT SERVICE
• ATTENDANT DELAY ANNOUNCEMENT
• LISTED DIRECTORY NUMBER DISPLAY-ATTENDANT
• ATTENDANT NIGHT TRANSFER
ND-91638-006(E) Page 5
Issue 3
MFC INCOMING CALL (CONT’D)
SERVICE CONDITIONS (CONT’D)
5. The MFC incoming call is available for the following trunk to trunk connections.
X:Available / —:Not available
Type of Connection MFC MFC MFC
to to to
Connection Method Tie CCIS PSTN
Tandem Connection X X —
Remote Access to System X X X
Call Forwarding-Outside X X X
Note 1: Incoming MFC call to Tie/CCIS network is available when the closed numbering is applied in
the Tie/CCIS network.
Note 2: When all outgoing trunks or target station in distant PBX is busy, the system send the backward
signal “called party idle” to the C.O. and sends the Busy Tone to the calling party.
6. This feature is applicable for the following countries.
X:Available / —:Not available
DOD with MFC
Countries DID with MFC
without ANI with ANI
ARGENTINA X X X
BAHRAIN X X X
BRAZIL X X X
CHILE X X X
COLOMBIA X — —
INDONESIA X X X
MALAYSIA X — —
MEXICO X X X
NORWAY X — —
POLAND X X X
SINGAPORE X — —
THAILAND X — —
VENEZUELA X — —
7. Refer to the Appendix 1 for signaling specifications.
Page 6 ND-91638-006(E)
Issue 3
MFC OUTGOING CALL
GENERAL DESCRIPTION
This feature allows a station, Dterm and Attendant to originate an outgoing call to the C.O. with the MFC
signaling.
STATION APPLICATION
All stations
DESK CONSOLE
SMART CONSOLE
OPERATING PROCEDURE
1. Lift the handset and receive Dial Tone
2. Dial access code for C.O. and receive pseudo Dial Tone from the system.
3. Dial desired number. Ring Back Tone will be sent from C.O.
4. When the called party answer, the parties are connected.
SERVICE CONDITIONS
1. It is required for the system to assign the number of digits for the outgoing call to the C.O. The system
will seize the outgoing trunk and send the dialed number to the C.O. after the station dials the preas-
signed number of digits. If the calling station does not dial the preassigned number of digits and in the
event of the resister timer out, the system will seize the outgoing trunk and send the dialed number to
the C.O. and wait the remaining digit(s).
If the all outgoing trunks are busy, the calling station will not hear the Busy Tone until the calling party
dials the preassigned number of digits or resister timer out.
2. It is not available to originate an MFC outgoing call by using the TRUNK LINE APPEARANCE
Dterm.
3. The ANI (Automatic Number Identification) service is available for the following countries.
• Argentina
• Bahrain
• Brazil
• Chile
• Indonesia
• Mexico
• Poland
ND-91638-006(E) Page 7
Issue 3
Note: When MFC outgoing call is originated from Dterm Sub Line or Virtual Line, the Sub Line or
Virtual Line number is sent to the C.O. as a Station Number.
b. If the calling party is Attendant, the Local Office Code is sent to the C.O. The Local Office Code is
assigned for each Attendant Group by system data programming.
c. If incoming trunk call to MFC trunk connection, the Local Office Code is sent to the C.O. The
Local Office Code is assigned for each Trunk Route Group by system data programming.
5. The following service features are available for MFC outgoing calls.
• CALL FORWARDING-OUTSIDE (ALL CALLS/BUSY LINE/DON’T ANSWER)
• SPEED CALLING-STATION/SYSTEM/ONE TOUCH-Dterm
• LAST NUMBER REDIAL
• STACK DIAL
• SAVE AND REPEAT
• OUTGOING TRUNK QUEUING
• TIMED QUEU-Dterm
• PASSING DIAL TONE
• HOTLINE-OUTSIDE
• SMDR
• TOLL RESTRICTION
• ACCOUNT CODE
• AUTHORIZATION CODE
• FORCED ACCOUNT CODE
6. The MFC outgoing call is available for the following trunk to trunk connections.
X:Available / —:Not available
Type of Connection Tie CCIS PSTN
to to to
Connection Method MFC MFC MFC
Tandem Connection X X —
Remote Access to System X — X
Call Forwarding-Outside X X X
Page 8 ND-91638-006(E)
Issue 3
X:Available / —:Not available
DOD with MFC
Countries DID with MFC
without ANI with ANI
ARGENTINA X X X
BAHRAIN X X X
BRAZIL X X X
CHILE X X X
COLOMBIA X — —
INDONESIA X X X
MALAYSIA X — —
MEXICO X X X
NORWAY X — —
POLAND X X X
SINGAPORE X — —
THAILAND X — —
VENEZUELA X — —
ND-91638-006(E) Page 9
Issue 3
This page is for your notes.
Page 10 ND-91638-006(E)
Issue 3
APPENDIX: Specifications by Country
1) Specifications of ARGENTINA
11 — — — —
12 — — — —
13 — — — —
14 — — — —
15 END OF — — —
PULSING
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
ND-91638-006(E) Page 11
Issue 3
2) Specifications of BAHRAIN
10 0 — — —
11 — — — —
12 REQUEST — — —
NOT
ACCEPTED
13 — — — —
14 — — — —
15 DIGIT — — —
SIGNAL
COMPLETE
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
Page 12 ND-91638-006(E)
Issue 3
3) Specifications of BRAZIL
7 7 — SEND LAST 2 —
DIGIT (n-2)
10 0 — — —
11 — CALL TRANSFER — —
12 — — — —
13 — — — —
14 — — — —
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” to the C.O.
Note 2: If the system received GII-3, 5, 7, 8 or 9, the incoming call is routed to the Attendant.
Note 3: In the event of the following timer out, the system disconnects the MFC resister/sender.
a. If it exceeds 7 sec. or more, to receive Forward Signal after the system sends the Backward
Signal.
b. If it exceeds 7 sec. or more, to receive next Forward Signal after the system detects previous
Forward Signal stop.
Note 4: The system does not sends the “GA-3” with pulse form, but the system can receive the“GA-3”
with pulse form.
Note 5: If the system receives invalid number or in the case of the called station is busy, the system
sends “GB-1” to C.O. and connects the incoming call to Attendant or predesignated station.
ND-91638-006(E) Page 13
Issue 3
4) Specifications of CHILE
9 9 INTERNATIONAL — TRANSMISSION SP
INFORMATION
10 0 UNIDENTIFIABLE — TRANSMISSION SP
SUBSCRIBER INFORMATION
11 — — INTERNATIONAL CONGESTION
12 — — INTERNATIONAL CONGESTION
14 — — — CONGESTION
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
Page 14 ND-91638-006(E)
Issue 3
5) Specifications of COLOMBIA
4 4 — CONGESTION CONGESTION
7 7 — — —
8 8 — — —
9 9 — — —
10 0 — — —
11 — — — —
12 — — — —
13 — — — —
14 — — — —
15 END OF — — —
NUMBER
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
ND-91638-006(E) Page 15
Issue 3
6) Specifications of INDONESIA
4 4 INTERNATIONAL 4 CONGESTION —
OPERATOR
7 7 INTERNATIONAL 7 — UNALLOCATED
TEST EQUIPMENT NUMBER
10 0 — 0 — —
11 REROUTE SP — — — —
SERVICE
SIGNAL
12 — — — — —
13 — — — — —
14 ACCESS TO — — — —
TEST
EQUIPMENT
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-5” to the C.O.
Note 2: The duration of the Backward Signal sent by the system is 200 ms.
Page 16 ND-91638-006(E)
Issue 3
7) Specifications of MALAYSIA/SINGAPORE
4 4 — CONGESTION CONGESTION
5 5 INTERNATIONAL CALL — —
6 6 TEST EQUIPMENT — —
8 8 INTERNATIONAL OPERATOR — —
10 0 — — —
11 — — — —
12 — — — —
13 — — — —
14 — — — —
15 — — — —
Note 1: When the system receives GII-1, 5, 7, 8 or 9 signal from the C.O., the incoming call is routed to
the Attendant.
Note 2: When the system receives GII-2, 3, 4 or 6 signal from the C.O. and the target station is idle, the
incoming call is routed to the target station.
ND-91638-006(E) Page 17
Issue 3
8) Specifications of MEXICO
12 — — — — — —
13 — — — — — —
14 — — — — — —
15 — — END OF — — —
DIGIT
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” to the C.O.
Page 18 ND-91638-006(E)
Issue 3
9) Specifications of NORWAY
4 4 — CONGESTION CONGESTION
5 5 — SEND CALLING —
PARTY NUMBER
6 6 — ADRS CONPLETE —
SPEECH CONN.
7 7 — — —
8 8 — — —
9 9 — — —
10 0 — — —
11 — — — —
12 REQUEST NOT — — —
ACCEPTED
13 ACCESS TO TEST — — —
EQUIPMENT
14 — — — —
15 END OF — — —
IDENTIFICATION
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
Note 2: If the system receives non-existing station number, the system sends the “GB-1” to the C.O.
and sends the Busy Tone to the calling party.
ND-91638-006(E) Page 19
Issue 3
10) Specifications of POLAND
2 2 SUBSCRIBER W/ PRIORITY — —
3 3 MAINTENANCE EQUIPMENT — —
4 4 — CONGESTION —
7 7 SUBSCRIBER — —
8 8 DATA TRANSMISSION — —
9 9 SUBSCRIBER W/ PRIORITY — —
10 0 OPERATOR FORWARD — —
TRANSFER
11 — — — —
12 — — — —
13 — — — —
14 — — — —
15 — — — —
Note 1: The system sends “GA-3”or “GA-6” to the C.O. after the system received all digits of station
number from the C.O.
The system does not send “GB” signals.
Page 20 ND-91638-006(E)
Issue 3
11) Specifications of THAILAND
4 4 — CONGESTION CONGESTION
8 8 INTERCEPTED OPERATOR — —
9 9 — — —
11 — — — —
12 — — — —
13 — — — —
14 — — — —
15 — NO INFORMATION — —
Note 1: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
Note 2: When the system receives GII-1, 6, 7, 8 or 9 signal from the C.O., the incoming call is routed to
the Attendant.
ND-91638-006(E) Page 21
Issue 3
12) Specifications of VENEZUELA
5 5 OPERATOR
9 9 —
11 — — — —
12 NO SUBSCRIBER — — —
IDENTIFICATION
13 — — — —
14 — — — —
15 END OF — — —
AVAILABLE
INFO.
Note 1: When the system receives “GA-10” or “GB-10” signal from C.O., the system disconnects the
incoming trunk.
Note 2: The system sends “GA-3” to the C.O. after the system received all digits of station number
from the C.O.
The system does not send “GA-4” or “GA-6” to the C.O.
Page 22 ND-91638-006(E)
Issue 3