Professional Documents
Culture Documents
Sony DSC H300
Sony DSC H300
983475511.pdf
Revision History
S.M. Rev.
Ver. Date History Contents
SERVICE MANUAL
issued
1.0 2013.09 Official Release — —
US Model
Ver. 1.0 2013.09 Canadian Model
AEP Model
UK Model
Internal memory Russian Model
ON BOARD E Model
Chinese Model
Brazilian Model
Caution 注意
Danger of explosion occurs if battery is incorrectly replaced. 如果电池更换不当会有爆炸危险。
Replace only with the same or equivalent type. 只能用同样类型或等效类型的电池来更换。
Dispose of used batteries according to the instructions. 务必按照说明处置用完的电池。
DSC-H300
–2–
1. SERVICE NOTE
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY 1-3. REGARDING FUSE
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) • MAIN BOARD
Note1: When replacing the Main Board Assy, erase the data in internal memory of main board before replacement.
Note2: When replacing the Main Board Assy, execute formatting and initialize the internal memory after replacement.
Ref. No: F1
Part No: 1-576-415-11
Method for Copying the Data in Internal Memory
Description: FUSE, MICRO (1608 TYPE) (2A/32V)
Copy
Ref. No: F2
Copies all images in the internal memory to a memory card. Part No: 1-576-415-11
1. Insert a memory card with sufficient free capacity into the camera. Description: FUSE, MICRO (1608 TYPE) (2A/32V)
2. MENU (Settings) (Memory Card Tool) [Copy] [OK]
Notes
Make sure there is sufficient battery power. Otherwise, the battery power may run out when you
attempt to copy image files, causing the copy to fail and possibly corrupt the data.
Images cannot be copied individually.
The original images in the internal memory are retained even after copying. To delete the contents
of the internal memory, remove the memory card after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
A new folder is created on the memory card and all the data will be copied to it. You cannot choose
a specific folder and copy images to it.
Format
Notes
Note that formatting permanently erases all data including even protected images.
DSC-H300
1-1E
2. REPAIR PARTS LIST
IDENTIFYING PARTS
NOTE: The components identified by mark 0 or dotted line with
• -XX, -X mean standardized parts, so they may have some differences from the mark 0 are critical for safety.
Follow the disassembly in the numerical order given.
original one. Replace only with part number specified.
• Items marked “*” are not stocked since they are seldom required for routine service.
Les composants identifiés par une marque 0 sont
Some delay should be anticipated when ordering these items. critiques pour la sécurité.
• The mechanical parts with no reference number in the exploded views are not Ne les remplacer que par une pièce portant le numéro
supplied. spécifié.
• Due to standardization, replacements in the parts list may be different from the
parts specified in the diagrams or the components used on the set.
• CAPACITORS: CAUTION
uF: μF Danger of explosion if battery is incorrectly replaced.
• COILS Replace only with the same or equivalent type.
uH: μH Dispose of used batteries according to the instructions.
• RESISTORS
3 Top Cover Section All resistors are in ohms. 注意
• ST Board Assy METAL: metal-film resistor 如果电池更换不当会有爆炸危险。
• Detect SW Board Assy METAL OXIDE: Metal Oxide-film resistor 只能用同样类型或等效类型的电池来更换。
F: nonflammable 务必按照说明处置用完的电池。
• SEMICONDUCTORS
In each case, u: μ, for example: • Color Indication of Appearance Parts
7 Front Cover Section uA...: μA... , uPA... , μPA... , Example:
uPB... , μPB... , μPC... , μPC... , (SILVER) : Cabinet’s Color
uPD..., μPD... (Silver) : Parts Color
2 LCD
Back View
IN Right View
MA
DSC-H300
2-1
OPERATION NOTES DISCHARGING OF THE CHARGING CAPACITOR
Make sure that the conductive side of a flexible board does not have any stain or foreign materials. The charging capacitor is charged up to the maximum 310 V
Do not touch the conductive side of flexible boards with bare hands. potential. Note: High-voltage cautions
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3) There is a danger of electric shock by this high voltage
Discharging the Capacitor
when the capacitor is handled by hand. The electric shock
Short-circuit between two points with
OK NG NG is caused by the charged voltage which is kept without dis- the short jig about 10 seconds.
(The flexible board was plugged in straight (The flexible board was plugged in (The flexible board was not plugged in charging when the main power of the unit is simply turned
and completely) crooked.) completely.)
off. Therefore, the remaining voltage must be discharged as
R:1 kΩ/1 W
Flexible Flexible described below.
Board Flexible (Part code: 1-215-869-11)
Flexible Board Flexible
Board Board
Reference line Flexible Reference line Board Preparing the Short Jig
Reference line Board To preparing the short jig, a small clip is attached to each end
of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
Connector Connector Connector Connector Connector Connector prevent electrical shock.
Fig. 1 Fig. 2 Fig. 3 1 kΩ/1 W
When opening the connector's holder in direction A, do not open When closing the connector's holder, press it evenly while pushing
it with excessive force. a flexible board in direction B.
Holder Holder
A Connector
Flexible Board
Connector Wrap insulating tape.
A Flexible Board
B
ST Board
Insulation side
• Make sure that the flat cable and flexible board are not cracked Cut and remove the part of gilt
or bent at the contact end. which comes off at the point.
(Be careful or some
• Do not apply excessive force to the gilded flexible board. pieces of gilt may be left inside)
ST Board
DSC-H300
2-2
2-1. EXPLODED VIEWS DISASSEMBLY
2-1-1. REAR SECTION 1. Remove in numerical order (1) in the left figure.
#S1
(Claws)
#S1
1
2 (Claws)
#S1
#S3
13
#S1
Ref. No. Part No. Description Ref. No. Part No. Description
1 #S2 X 4
#S1 Note: Before replacing the MAIN Board, remove the Lens Block and
write down the lens data on the label attached to the side of #S2
3 the lens. #S2
For details, refer to Adjustment “5-3-1. Writing Lens data.”
#S2 3 #S2 X 3 → Pop up the Strobe (3-1) → #S1 X 2 → Remove the Top Cover Section (3-2)
(Claws)
Back View #S1
#S2 3-1
#S2
(Claws)
#S2
Lens Section
(See page 2-5)
DISCHARGING OF THE CHARGING CAPACITOR
#S2 Black
1 ns 1
5 51 5 Remove the Solderings → #S2 X 4
(Note)
Back View
#S1 Pink Blue
White Blue
1 #S3 X 2 2 #S5 X 3
#S3 #S5
Note
Note 1: Refer to “Assembly-3: How to distinguish the side of Optical
Filter Block facing to Lens Device”.
Note 2: Before replacing the Lens Block, write down the lens data on
the label attached to the side of the lens.
For details, refer to Adjustment “5-3-1. Writing Lens data”.
2 101 (Note 2, 3)
106
Very weak
#S5 #S8
#S5
106 102 #S8
(Note 1)
107 103 #S8
104
Ref. No. Part No. Description Ref. No. Part No. Description
101 A-1989-706-A LENS BLOCK ASSY (Note 2, 3) 106 4-447-160-01 DAMPER, LENS
102 4-488-393-01 OPTICAL FILTER BLOCK (Note 1) 107 4-488-399-01 SPONGE, LENS CUSHION
103 4-488-394-01 CCD RUBBER
104 A-1989-700-A CCD BLOCK ASSY #S2 4-488-402-01 SCREW_TP_1.7_4.0_SVR_AB
105 4-447-142-01 BASE PLATE, TRIPOD #S3 4-447-230-01 SCREW, M1.7X3
#S5 4-488-404-01 SCREW_TP_1.7_5.5_SVR_AB
#S8 4-274-002-01 SCREW_TP_1.4_3_SVR_AB
DSC-H300
2-5
2-1-4. FRONT COVER SECTION
DISASSEMBLY
ns: not supplied
1. Remove in numerical order (1) in the left figure.
151
#S2 #S1 #S1
1
ns 152
#S6
#S1
#S2
1
#S2
#S1
153
Ref. No. Part No. Description Ref. No. Part No. Description
151 X-2588-845-1 LENS HOLDER #S1 4-488-403-01 SCREW_TP_1.7_4.5_BLK_AB
152 X-2588-848-1 COVER ASSY, FRONT #S2 4-488-402-01 SCREW_TP_1.7_4.0_SVR_AB
153 4-488-388-01 COVER, USB #S6 4-447-225-01 SCREW, TP1.4X6 SVR
DSC-H300
2-6
2-1-5. MAIN FRAME SECTION
Note
ns: not supplied
Note: Refer to “Assembly-1: Routing harnesses (Main frame section) ”.
#S2 208
210
(Note)
209
#S2
212 207
ns
211
(Note)
213 206
#S2
203 205
ns
202
201
204
Ref. No. Part No. Description Ref. No. Part No. Description
201 4-488-397-01 COVER(O), EYELET 211 X-2586-051-1 CAPACITOR ASSY, MAIN (Note)
202 4-488-390-01 EYELET(O), STRAP 212 A-1990-209-A FRAME ASSY, BATT CHAMBER
203 A-1989-735-A SPEAKER ASSY 213 X-2588-882-1 FRAME ASSY, MAIN
204 X-2588-844-1 LID ASSY, BATT
205 4-488-389-01 SHAFT, BATT LID #S2 4-488-402-01 SCREW_TP_1.7_4.0_SVR_AB
(Claws) Note
251
#S7
253 (Note)
255
256
#S2
#S7 254
#S7
258 (Note)
#S2
ns
259
ns
Bottom View
#S2
Red
#S2 Black Blue Blue Red
#S2 #S2
257 (Note)
#S2
Ref. No. Part No. Description Ref. No. Part No. Description
251 X-2588-847-1 COVER ASSY, TOP 256 A-1989-701-A BLOCK ASSY, RL FPC
252 X-2588-863-1 BASE ASSY, RL DIAL 257 A-1989-702-A BOARD ASSY, DETECT SW (Note)
253 A-1989-704-A ST BOARD ASSY (Note) 258 A-1989-708-A BASE ASSY, FLASH (Note)
254 4-488-392-01 FPC BOARD, ST CONNECTION 259 4-447-165-01 DIFFUSION PANEL
255 4-488-401-01 BUTTON, POWER
#S1 4-488-403-01 SCREW_TP_1.7_4.5_BLK_AB
#S2 4-488-402-01 SCREW_TP_1.7_4.0_SVR_AB
#S7 4-273-597-01 SCREW_TP_1.4_3.5_SVR_AB
DSC-H300
2-8
ACCESSORIES
901 902 903 904 905
Ref. No. Part No. Description Ref. No. Part No. Description
901 1-837-783-31 Dedicated USB cable * 905 4-476-544-81 Instruction Manual (SIMPLIFIED CHINESE)
902 2-629-892-11 Shoulder strap * 905 4-476-545-11 Instruction Manual (ENGLISH, FRENCH, ITALIAN,
903 4-488-387-01 Lens cap SPANISH, PORTUGUESE, GERMAN, DUTCH,
904 4-451-696-01 Lens cap strap POLISH, CZECH, HUNGARIAN, SLOVAK, SWEDISH,
* 905 4-476-544-11 Instruction Manual (ENGLISH) FINNISH, NORWEGIAN, DANISH, CROATIAN,
ROMANIAN, GREEK)
* 905 4-476-544-21 Instruction Manual (ENGLISH, SPANISH) * 905 4-476-545-21 Instruction Manual (ENGLISH, TURKISH,
* 905 4-476-544-31 Instruction Manual (ENGLISH, FRENCH) TRADITIONAL CHINESE, SIMPLIFIED CHINESE,
* 905 4-476-544-41 Instruction Manual (RUSSIAN, UKRAINIAN) MALAY, INDONESIAN, THAI, ARABIC, PERSIAN)
* 905 4-476-544-51 Instruction Manual (SPANISH, BRAZILIAN
PORTUGUESE) Note 1: Dedicated A/V cable (optional accessory)
* 905 4-476-544-61 Instruction Manual (ARABIC, PERSIAN) Dedicated A/V cable is not supplied with this model.
If you need dedicated A/V cable, order 1-834-312-4[] or VMC-
15CSR1.
This item is supplied with the unit as an accessory, but is not prepared as a service part.
951
DSC-H300
2-9E
3. ASSEMBLY
Assembly-1: Routing harnesses (Main frame section) Assembly-3: How to distinguish the side of Optical Filter Block
facing to Lens Device
The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).
Harnesses of Harnesses of
the Flash Unit the Detect SW Board
DSC-H300
3-1E
4. BLOCK DIAGRAMS
DSC-H300
4-1E