Professional Documents
Culture Documents
Part2
Part2
H Designator: H Designator:
Cast Iron Section Heating Boilers Field Assembly of Boilers
H Designator :
Heating Boilers, Except Cast Iron
HLW Designator : HV Designator :
Lined Potable Water Heaters H Heating Boiler Safety Valves
5
ASME’s Boiler and Pressure Vessel Code (BPVC) | 2013
Pressure Vessels
Section VIII – Pressure Vessels Division 2 requirements on materials, Referenced BPVC Sections
design, and nondestructive examination
Division 1 provides requirements BPVC-II, A, B, C, D --
are more rigorous than in Division 1;
applicable to the design, fabrication, Section II, Materials, Parts A through D
however, higher design stress intensify
inspection, testing, and certification
values are permitted. These rules may BPVC-V --
of pressure vessels operating at either
also apply to human occupancy pressure Section V, Nondestructive Examination
internal or external pressures exceeding
vessels typically in the diving industry.
15 psig. Such vessels may be fired or BPVC-IX --
Rules pertaining to the use of the single
unfired. This pressure may be obtained Section IX, Welding and Brazing
ASME certification mark with the U2 and
from an external source or by the Qualifications
UV designators are also included.
application of heat from a direct or
indirect source, or any combination Division 3 requirements are applicable
thereof. Specific requirements apply to to pressure vessels operating at either
several classes of material used in internal or external pressures generally
pressure vessel construction, and also above 10,000 psi. It does not establish
to fabrication methods such as welding, maximum pressure limits for either Section
forging and brazing. VIII, Divisions 1 or 2, nor minimum pressure
limits for this Division. Rules pertaining
Division 1 contains mandatory and
to the use of the single ASME certification
non-mandatory appendices detailing
mark with the U3 and UV3 designator are
supplementary design criteria,
also included.
nondestructive examination and
inspection acceptance standards. Rules
pertaining to the use of the single ASME
certification mark with the U, UM and UV
designators are also included.
6
7
ASME’s Boiler and Pressure Vessel Code (BPVC) | 2013
8
ASME’s Boiler and Pressure Vessel Code (BPVC) | 2013
Transport Tanks
Section XII – Transport Tanks Referenced BPVC Sections Referenced ASME Standards
Provides requirements for construction BPVC-II, A, B, C, D -- B1.1 --
and continued service of pressure vessels Section II, Materials, Parts A through D Unified Inch Screw Threads
for the transportation of dangerous (UN and UNR Thread Form)
BPVC-V --
goods via highway, rail, air or water at
Section V, Nondestructive Examination B1.20.1 --
pressures from full vacuum to 3,000
Pipe Threads, General Purpose, Inch
psig and volumes greater than 120 BPVC-VIII-1-2 –
gallons. “Construction” is an all-inclusive Section VIII, Pressure Vessels, Nine Standards from the B16 Series
term comprising materials, design, Division 1 and Division 2 on pipe flanges and fittings
fabrication, examination, inspection,
BPVC-IX -- B18.2.2 --
testing, certification, and over-pressure
Section IX, Welding and Brazing Square and Hex Nuts
protection. “Continued service” refers to
Qualifications
inspection, testing, repair, alteration, and B36.10M --
recertification of a transport tank that Welded and Seamless Wrought
has been in service. Rules pertaining to Steel Pipe
the use of the single ASME certification
mark with the T, TD, and TV designators PTC 25 --
are included. Pressure Relief Devices
QAI-1 --
Qualifications for
Authorized Inspection
10