Professional Documents
Culture Documents
12 00 Pi SPC 00020
12 00 Pi SPC 00020
12 00 Pi SPC 00020
CONTRACT TITLE :
EPCC of the Sulfur Facilities for the North Field Expansion (NFXP) Project - EPC4
TITLE :
COMPANY
CONTRACTOR
This document is property of Técnicas Reunidas. Its reproduction without a written permission is strictly forbidden.
DocuSign Envelope ID: DF021043-73D6-4A17-9AB1-D14396EE25FB
COMPANY: Contract No.:
QATARGAS OPERATING COMPANY LIMITED LTC/C/NFE/5022/20
PROJECT:
Doc. No.:
SULFUR FACILITIES FOR THE NORTH FIELD EXPANSION (NFXP)
12-00-PI-SPC-00020
PROJECT - EPC-4
CONTRACTOR: Rev. 1
TÉCNICAS REUNIDAS S.A. & WISON ENGINEERING LTD. JV PAGE 2 OF 6
Doc. Title: COMMON NFXP4 TECHNICAL SPECIFICATION FOR GASKETS
Table of Contents
1. GENERAL ......................................................................................... 3
1.1 PURPOSE AND SCOPE ....................................................................... 3
1.2 REFERENCES ...................................................................................... 3
1.3 DEFINITION .......................................................................................... 4
2. GENERAL REQUIREMENTS ........................................................... 4
2.1 DESIGN / DIMENSIONS........................................................................ 4
2.2 POSITIVE MATERIALS IDENTIFICATION (PMI) .................................. 5
2.3 MATERIAL REQUIREMENTS ............................................................... 5
3. TESTS AND INSPECTIONS ............................................................. 5
4. MATERIAL CERTIFICATION / MARKING........................................ 6
5. OTHERS ............................................................................................ 6
This document is property of Técnicas Reunidas. Its reproduction without a written permission is strictly forbidden.
DocuSign Envelope ID: DF021043-73D6-4A17-9AB1-D14396EE25FB
COMPANY: Contract No.:
QATARGAS OPERATING COMPANY LIMITED LTC/C/NFE/5022/20
PROJECT:
Doc. No.:
SULFUR FACILITIES FOR THE NORTH FIELD EXPANSION (NFXP)
12-00-PI-SPC-00020
PROJECT - EPC-4
CONTRACTOR: Rev. 1
TÉCNICAS REUNIDAS S.A. & WISON ENGINEERING LTD. JV PAGE 3 OF 6
Doc. Title: COMMON NFXP4 TECHNICAL SPECIFICATION FOR GASKETS
1. GENERAL
This specification applies to the manufacturing of Gaskets to be used for Sulfur Facilities for the
North Field Expansion (NFXP) Project - EPC-4.
Gaskets shall be supplied in accordance with the latest applicable codes, standards and
specifications listed in Para. 1.2 and the additional requirements of this specification shall also
be applied.
1.2 REFERENCES
The latest edition as of April-2022 of the codes and standards shall be applied.
This document is property of Técnicas Reunidas. Its reproduction without a written permission is strictly forbidden.
DocuSign Envelope ID: DF021043-73D6-4A17-9AB1-D14396EE25FB
COMPANY: Contract No.:
QATARGAS OPERATING COMPANY LIMITED LTC/C/NFE/5022/20
PROJECT:
Doc. No.:
SULFUR FACILITIES FOR THE NORTH FIELD EXPANSION (NFXP)
12-00-PI-SPC-00020
PROJECT - EPC-4
CONTRACTOR: Rev. 1
TÉCNICAS REUNIDAS S.A. & WISON ENGINEERING LTD. JV PAGE 4 OF 6
Doc. Title: COMMON NFXP4 TECHNICAL SPECIFICATION FOR GASKETS
1.3 DEFINITION
2. GENERAL REQUIREMENTS
4) When “F-JKT” (For Full Jacketed flange, 2-size designation) is defined in the material
description, outside diameter of gasket shall meet to larger size while inside diameter to
smaller size.
5) Ring joint gaskets shall be made fully in accordance with the material description (sharp,
material spec and maximum hardness)
6) Sheet gasket shall be one-piece type. Separate type (dove-tail type) shall not be applied.
This document is property of Técnicas Reunidas. Its reproduction without a written permission is strictly forbidden.
DocuSign Envelope ID: DF021043-73D6-4A17-9AB1-D14396EE25FB
COMPANY: Contract No.:
QATARGAS OPERATING COMPANY LIMITED LTC/C/NFE/5022/20
PROJECT:
Doc. No.:
SULFUR FACILITIES FOR THE NORTH FIELD EXPANSION (NFXP)
12-00-PI-SPC-00020
PROJECT - EPC-4
CONTRACTOR: Rev. 1
TÉCNICAS REUNIDAS S.A. & WISON ENGINEERING LTD. JV PAGE 5 OF 6
Doc. Title: COMMON NFXP4 TECHNICAL SPECIFICATION FOR GASKETS
7) Outer ring shall be provided for all spiral wound gaskets. When “W/IOR” is specified in
the material description, inner shall be also provided as specified in material descriptions.
2) Leachable chlorite in flexible graphite material shall be less than 100 ppm for flexible
graphite filler for spiral-wound gaskets and EXP-GRAPHITE gasket.
Vendor shall conduct tests and / or inspections in accordance with the relevant codes and
standards listed in Para. 1.2 and the additional requirements of this specification together with
the following:
1) Vendor shall perform tests and / or inspections under Vendor 's own
quality control and shall provide sound quality products.
2) Vendor has the responsibility of providing CONTRACTOR's inspector with all specified
information, and the inspector shall have free access to witness or audit Vendor 's quality
control at Vendor 's facilities throughout the time while work on the products is being
executed, as deemed necessary.
This document is property of Técnicas Reunidas. Its reproduction without a written permission is strictly forbidden.
DocuSign Envelope ID: DF021043-73D6-4A17-9AB1-D14396EE25FB
COMPANY: Contract No.:
QATARGAS OPERATING COMPANY LIMITED LTC/C/NFE/5022/20
PROJECT:
Doc. No.:
SULFUR FACILITIES FOR THE NORTH FIELD EXPANSION (NFXP)
12-00-PI-SPC-00020
PROJECT - EPC-4
CONTRACTOR: Rev. 1
TÉCNICAS REUNIDAS S.A. & WISON ENGINEERING LTD. JV PAGE 6 OF 6
Doc. Title: COMMON NFXP4 TECHNICAL SPECIFICATION FOR GASKETS
1) Type “B” or "3.1" certificate shall be required in accordance with Spec. 12-00-QM-
SPC-00001 “COMMON NFXP4 Specification for Certification, Marking and
Traceability of Materials".
2) Color Coding for spiral-wound gasket and glass reinforced PTFE gaskets shall be in
accordance with Spec. 12-00-PI-SPC-00007 “COMMON NFXP4 Piping - Color
Coding for Material Identification”
3) Gaskets shall be marked in accordance with the requirements of relevant codes. The
centre ring of each gasket shall be permanently marked by stamping or etching with
letter of minimum height 2.5 mm. In addition to applicable code and standard, following
information shall be included with centering ring markings;
c) Flange size
d) Rating designation
5. OTHERS
1) This specification has priority over the others specified in the applicable documents.
2) Manufacturing shall submit manufacturing, test, inspection and welding procedures for
CONTRACTOR's approval prior to manufacturing.
This document is property of Técnicas Reunidas. Its reproduction without a written permission is strictly forbidden.