Professional Documents
Culture Documents
MT7626
MT7626
DESCRIPTION FEATURES
MT7626 is a high efficiency TRIAC dimmable Wide range of TRIAC dimming compatibility
linear constant current LED driver. MT7626 Supports front/back edge dimmer
supports front/back edge dimmer with high
System efficiency up to 84%
output current accuracy and no EMI issues. The
Supports to drive external current expansion
peripheral circuit is extremely simplified. Output
chip to enhance the output power
current can be flexibly adjusted by external
Good Line regulation
resistor RSET. Widely apply to various LED
lighting applications with high power factor. Internal high voltage startup circuit
MT7626 is designed with an internal efficiency Saves VCC capacitor, low BOM cost
improvement circuit and uses MAXIC proprietary No magnetic components required
control algorithm to achieve good compatibility of ±5% LED output current accuracy
TRIAC dimmer, as well as up to 84% system LED current set by external resistor
efficiency. The internal line compensation circuit
Embedded thermal regulation function
has good line regulation and MT7626 can drive
Available in ESOP8 package
external current expansion chip (MT7623) to
enhance the output power.
Moreover, MT7626 is designed with thermal
regulation function. When the junction APPLICATION
temperature goes higher than the threshold, the
GU10/E27/E14 LED bulb, LED filament lamp
embedded thermal regulation module can
LED downlight, LED ceiling lamp
automatically reduce the output current to
Other LED lightings applications
improve the system reliability. No need of
inductor, transformer or other magnetic
components. The system topology is simplified
with few peripheral components, while also
reducing the system BOM.
C1
D1
LED
MT7626
BD1 VIN DRN
5 4
IB GATE
TRIAC 3 8
NC GND CAP
VAC 1 7
CS2 RSET
2 6
C2
FU1
RSET
THERMAL RESISTANCE①
Note:
① RθJA, RθJC are measured in the natural convection at TA = 25°C on a low effective single layer
thermal conductivity test board of JEDEC 51-3 thermal measurement standard. Test condition:
Device mounted on 2” X 2” FR-4 substrate PCB, 2oz copper, with minimum recommended pad on
top layer and thermal vias to bottom layer ground plane
ORDERING INFORMATION
MT7626
Tape
MT7626 ESOP8 YYWWXX
4,000 Pcs/Reel
XXXX
PIN CONFIGURATIONS
PIN DESCRIPTION
ELECTRICAL CHARACTERISTICS
(Test conditions: VIN=20V, TA=25°C unless otherwise stated)
Symbol Parameter Conditions Min Typ Max Unit
APPLICATION INFORMATION
The MT7626 is a high efficiency TRIAC there is a TRIAC dimmer connected into the
dimmable linear constant current LED driver. system, then the system outputs Bleeder current
MT7626 supports front/back edge dimmer with which is required by dimmer from IB pin
high output current accuracy, good compatibility automatically; if there is no TRIAC dimmer
and no EMI issues. connected, then the Bleeder current is turned off.
MT7626 is designed with an internal efficiency To be compatible with the TRIAC dimmer which
improvement circuit and uses MAXIC proprietary requires higher Bleeder current, CS2 pin
control algorithm to achieve good compatibility of connects an external capacitor to GND to
TRIAC dimmer, as well as up to 84% system increase Bleeder current. Calculate the Bleeder
efficiency. The internal line compensation circuit current as follow.
has good line regulation and MT7626 can drive
600mV
external current expansion chip to enhance the IB 30mA
output power. No need of inductor, transformer RCS 2
or other magnetic components. The system
topology is simplified with few peripheral
Output Power Enhancement
components, while also reducing the system
BOM. MT7626 can drive external current expansion
chip (MT7623) through GATE pin to enhance the
Start Up output power. MAXIC provides the
corresponding current expansion chip-MT7623.
After the system is powered on, VIN gets the
power from internal JFET. When the voltage of
VIN is higher than 13V, the chip starts working High Temperature Regulation
normally. When the junction temperature exceeds TREG
(153±5°C), the output current is automatically
Output LED Current reduced to protect the LED lamps and greatly
extend the system lifetime.
The LED current can be set by external resistor.
The input AC voltage is 120V 60Hz, and output
voltage is 135V. Calculate LED current as follow. PCB Layout Consideration
The actual output power is related to the PCB
180mV
I LED layout design and heat dissipation. The bottom
RSET plane of the chip is the thermal pad connecting
with GND. During PCB layout design, the copper
Bleeder Current
area which is connected to the GND plane
The integrated Bleeder circuit supports TRIAC
should be as large as possible, and aluminum
dimming. Through IB pin, the sensing circuit
substrate should be used as well.
senses whether a TRIAC dimmer is connected. If
PACKAGE INFORMATION
Important Notice
Maxic Technology Corporation (Maxic) reserve the right to make correction, modifications,
enhancements, improvements and other changes to its products and services at any time and to
discontinue any product or service without notice. Customers should obtain the latest relevant
information before placing orders and should verify that such information is current and complete.
All products are sold subject to Maxic’s terms and conditions of sale supplied at the time of order
acknowledgement.
Reproduction, copying, transferring, reprinting this paper without Maxic’s written permission is
prohibited.
Maxic assumes no liability for applications assistance or the design of customers’ products. Maxic
warrants the performance of its products to the specifications applicable at the time of sale.
Customers are responsible for their products and applications using Maxic components. To
minimize the risks associated with customers’ products and applications, customers should
provide adequate design and operating safeguards.