Professional Documents
Culture Documents
DTVenus2 Data Sheet - 20161221
DTVenus2 Data Sheet - 20161221
DTVenus2 Data Sheet - 20161221
Dec. 2016
~1~
Data Sheet
Revision History
PCB
Rev. date Revision Details
Version
Aug. 2016 Engineering Sample
Sept. 2016 Initial version issued
Correction the type on the page 10, from NC to below roles
6.2.1 8-bit LVDS Output
Oct . 2016
Pin 4 : Option for MCU_SCL
Pin 5 : Option for MCU-SDA
Nov 2016 Added the CDS sensor(JP3) & Speaker connector(CN10)
4.1 Main Board (140 x 100 mm)
6.2.15 CDS Sensor(option)
6.2.16 Speaker for HDMI input
~2~
Data Sheet
Contents
The information presented in this document may form a part of quotation or contract
under the agreement of both parties. Otherwise, this datasheet is subject to change
without notice.
~3~
Data Sheet
1. Spec Summary
2. General Description
This AD Board is an advanced TFT LCD Monitor Control Board. This design enables a full conventional
CRT monitor & AV Monitor replacement with a large size Active Matrix LCD module.
It is suitable for video resolution up to WUXGA @ 60Hz in all video modes; the full display area of the
module is used. The design is implemented as a single printed circuit board.
As this AD board is designed to act as a full monitor interface. Besides the main functionality of an analog
and Video, DVI, HDMI also various appealing On-Screen-Display Menu layouts are possible on customer’s
request.
This AD board is designed to support various TFT LCDs under the WUXGA resolution by BIOS option,
customer’s line-up their monitors with their own identity with following options.
~4~
Data Sheet
3. Block Diagram
~5~
Data Sheet
4. Dimension and Pictures - Main Board
no CON Service
1 CN10 Audio Volume Controller
2 CN14 8-bit LVDS to LCD Panel
3 CN15 Extra LVDS for 10-bit Panel
4 CN4 Touch Power Controller
Selection Jumper
5 JP2 for the type of
inverter diming
6 CN3 Inverter
12V DC from SMPS or
7 CN2
System Power
8 CN12 RS232 Serial Connector
12 CN9 OSD
13 JP3 CDS
14 CN10 Speaker
~6~
Data Sheet
4.2 Main Board Picture
Plane View
Front View
~7~
Data Sheet
5. Dimension and Pictures - OSD Board
~8~
Data Sheet
Option model for Open Frame or complete set solution
The OSD PCB consists of all in one type and split I/R sensor part.
In case of split type, the user can make it two different parts by cut easily.
(the boarder line between OSD body and split I/R sensor part was made by half cut condition)
Laminate Sticker for fine finishing the open frame or complete set (option)
~9~
Data Sheet
6. Connectors and Pin information
6.2.2 Extra LVDS output for 10-bit panel : LVDS 4Pin (12507WR-04P) / CN15
Pin No. Function Pin No Function Pin No. Function Pin No. Function
1 TXE4+ 2 TXE4 3 TXO4+2- 4 TXO4-
~ 10 ~
Data Sheet
6.2.4 HDMI Input
Pin Function Pin Function Pin Function Pin Function Pin Function
1 Data2 + 5 Data1 Shield 9 Data0 - 13 CEC 17 DDC/CEC GND
2 Data2 Shield 6 Data1 - 10 CLK + 14 NC 18 DC +5V
3 Data2 - 7 Data0 + 11 CLK Shield 15 DDC SCL 19 HP Detect
4 Data1 + 8 Data0 Shield 12 CLK - 16 DDC SDA
~ 11 ~
Data Sheet
6.2.13 Audio output & Control : CN10 (SMAW200-05)
Pin No. Function Pin No. Function Pin No. Function
1 STAND-BY 2 Mute 3 VOL
4 LEFT-AUDIO 5 RIGHT-AUDIO
~ 12 ~
Data Sheet
7. Setup for Operation
The OSD (On Screen Display) provides certain functions to have clear image and others.
This board supports 5 buttons OSD Menu operation as a standard.
The control functions defined on OSD operation are as below.
7.2 Caution
Once having been fit up all the components or having been downloaded by a revised Hex file, all
users are requested to the following procedures ;
-. Menu --> Option --> Restore Default --> Yes : press enter
-. Menu --> Function --> HDMI --> PC for just RGB or DVI on the computer connection and Video
No Over Scan for DVD Player or other Video setting case
Having been executed the above procedure. Then all users don’t need to do it again until any
firmware update or change.
~ 13 ~
Data Sheet
7.3 Menu Selection on the OSD Menu
7.3.2 by the OSD board manually (standard accessory - 5 Button Key Pad type)
The manual setting can be done by the pressing the above buttons.
The setting algorithm is very the same as the logic of Key board of normal computer.
There are some hot keys are reserved for users' convenience as follows.
.
Pressing method the buttons Function
Just pressing the Down key Auto Adjust
Pressing the Down key after pressing the Up key. Dimming down (luminance getting decrease gradually)
Pressing the Up key after pressing the Up key. Dimming up (luminance getting increase gradually)
~ 14 ~
Data Sheet
7.4. OSD Menu Tree
The signal source selection:
-. Press the “Set” button on the OSD Board & Press the Remote Controller (RGB, DVI, HDMI, CVBS)
-. When user activates the “Auto Color” menu, there must be existed the black and white clearly as
background image. (the most easiest condition : please use the Auto Color menu when the background
image is opened the MS-Word or Excel file on the screen)
~ 15 ~
Data Sheet
~ 16 ~
Data Sheet
(3) Function Menu
In case of resolution setting "XGA Mode" on the above, it has almost things to do with the
TFT Displays which have only the following resolutions ;
1024 x 768, 1280 x 768, 1366 x 768, 1360 x 768
Therefore, if the user need to apply the other wide XGA models such as the 1280 x 800 TFT
display, the users don't need to select this "XGA Mode" setting but just skip this setting
procedure.
~ 17 ~
Data Sheet
8. Applicable Graphic Mode
The microprocessor measures the H-sync, V-sync and V-sync/H-sync polarity for RGB inputs, and uses
this timing information to control all of the display operation to get the proper image on a screen.
This board can detect all VESA standard and MAC Graphic modes shown on the table below and provide
more clear and stable image on a screen.
~ 18 ~
Data Sheet
9. Appendix - A (Option : 24V DC Power Board)
This is an optional daughter board which can support the direct power supply (24V DC) from a SMPS or
System Power, then discharges the 12V DC to AD card or similar devises and the 24V DC by-pass to
backlight of LCD display directly.
Output Characteristics
OUTPUT 24V
HI
DIMMING DIMMING
~ 19 ~
Data Sheet
J2
Inverter Control
DC in (24V)
J4
J6
J7 J5
~ 20 ~
Data Sheet
10. Appendix - B (Option : Audio + 24V DC Daughter board)
This is an optional daughter board which can support the direct power supply (24V DC) from a SMPS or
System Power then discharges the 12V DC to AD card or similar devises and the 24V DC by-pass to
backlight of LCD display directly. and also it serves the Audio system as well.
1 1
2 2
3
~ 21 ~
Data Sheet
10.2 Dimension and Picture (100 X 60 mm) DC 24V Inverter Dimming Control
Control Out
DC 12V Inverter Dimming
[Connect on Venus(CN6)]
10.2.1 Top View
[Connect on Venus(CN12)]
Audio Volume Control
CN4
CN5
Power(SMPS)
Audio Out
CN3
(Speaker)
24VDC Input
CN2
CN6
CN1
J2
J3 J1
24VDC Input
Audio In Audio Out
(Speaker & Earphone)
CN6
J3
~ 22 ~
Data Sheet
10.3 Pin Information
~ 23 ~
Data Sheet
11. Appendix - C (Option : RS232C Protocols)
11.1 RS-232 Serial control
~ 24 ~
Data Sheet
Header Command *Data Type *Data *Check
Command
(1) (1) (1) (1) (1)
0x00 Normal
0x01 Warm
Color Mode 0x16 -
0x02 Cool
0x03 User
0x00 0
Color Red 0x17 ~ ~
0xFF 255
0x00 0
Color Green 0x18 ~ ~
0xFF 255
0x00 0
Color Blue 0x19 ~ ~
0xFF 255
0x00 Off
0x01 Weak
3DNR 0x1A 0x02 Standard -
0x03 Strong
0x04 Auto
0x00 0
Backlight 0x1B ~ ~
0x64 100
Auto Color 0x1C 0x00 0x00 Execution
Request
0xAA
0x80: Decrease by 1 0x00 0
Adv. H-Position 0x20 0x81: Increase by 1 ~ ~ -
Response 0xFF: Data Read 0x64 100
0x55
0x00 0
Adv. V-Position 0x21 ~ ~ -
0x64 100
0x00 0
Adv. Clock 0x22 ~ ~ -
0x64 100
0x00 0
Adv. Phase 0x23 ~ ~ -
0x64 100
Adv.Auto 0x24 0x00 0x00 Execution
Request
0x00 English
0xAA
0x00: Value 0x01 French
0x80: Decrease by 1 0x02 Spanish
Menu Language 0x40
0x81: Increase by 1 0x03 Deutsch
Response
0xFF: Data Read 0x04 Nederland
0x55
0x05 Italiano
~ 25 ~
Data Sheet
Header Command *Data Type *Data *Check
Command
(1) (1) (1) (1) (1)
0x00 English
0x01 French
0x02 Spanish
Menu Language 0x40
0x03 Deutsch
0x04 Nederland
0x05 Italiano
0x00 0%
0x00: Value
0x01 25%
0x80: Decrease by 1
Transparency 0x41 0x02 50%
0x81: Increase by 1
0x03 75%
0xFF: Data Read
Request 0x04 100%
0xAA 0x00 Off
0x01 5 Sec.
0x02 15 Sec.
OSD Time Out Response 0x42
0x03 30 Sec.
0x55 0x04 45 Sec.
0x05 60 Sec.
Restore Default 0x43 0x00 0x00 Execution
CVBS Source
0x44
Setting
HDMI Source 0x00: Value
0x45
Setting 0x80: Decrease by 1 0x00 Off
DVI Source 0x81: Increase by 1 0x01 On
0x46
Setting 0xFF: Data Read
RGB Source
0x47
Setting
0x00 0ff
0x01 1 Min.
0x02 5 Min.
0x03 10 Min.
0x04 15 Min.
0x05 30 Min.
Sleep Timer 0x50
0x06 45 Min.
Request 0x07 60 Min.
0xAA 0x00: Value 0x08 90 Min.
0x80: Decrease by 1 0x09 120 Min.
0x81: Increase by 1 0x0A 180 Min.
Response 0xFF: Data Read 0x0B 240 Min.
0x55 0x00 Normal
Zoom Mode 0x51 0x01 Wide
0x02 Zoom
0x00 Off
Auto Source 0x54
0x01 On
0x00 PC
HDMI Mode 0x55 0x01 Video
0x02 No Overscan
~ 26 ~
Data Sheet
Header Command *Data Type *Data *Check
Command
(1) (1) (1) (1) (1)
0x00 Off
Image Flip 0x56
0x01 On
0x00 Off
Image Mirror 0x57 0x00: Value
0x01 On
0x80: Decrease by 1
0x81: Increase by 1 0x00 1024x768
0xFF: Data Read 0x01 1280x768
XGA Mode 0x58 0x02 1360x768
0x03 1366x768
0x04 1024x600
* Check sum = Header Byte XOR Command XOR Byte Type Byte XOR Data Byte
IRKEY_POWER = 0x00,
IRKEY_INPUT_SOURCE = 0x12,
IRKEY_AUTO = 0x03,
IRKEY_MENU = 0x02,
IRKEY_UP = 0x05,
IRKEY_DOWN = 0x0D,
IRKEY_LEFT = 0x08,
IRKEY_RIGHT = 0x0A,
IRKEY_AV = 0x0C,
IRKEY_HDMI = 0x07,
IRKEY_DVI = 0x06,
IRKEY_PC = 0x04,
IRKEY_SELECT = 0x09,
~ 27 ~
Data Sheet
12. Appendix – D (Dip Switches’ Setting and supportable LCD Panel List)
+12V
+5V
+3.3V
In the case of the panel’s logic voltage is 10V and the current is under 300mA, the Venus2
board have to have LDO for the panel VCC at location U6. At that time you have to remove
this jumper.
In the case of the panel’s logic voltage is 10V and the current is over 300mA, the Venus2
board have to have addition option board instead of the LDO at location U6. The additional
option board is not defined yet. At that time you have to remove this jumper.
DC Level
PWM
~ 28 ~
Data Sheet
12.2.3 LVDS Type selection; SW1
LVDS Type Setting of the 8th switch
VESA format
“ Please see the actual dip switch position for LCD panel selection and all the setting
positions of jumper switches from the following pages. "
~ 29 ~
Data Sheet
13. Appendix – E (Firmware Upgrade)
3. Write the Firmware at the root folder of any USB memory stick.
The Firmware file name is ‘XH_V59XUS.bin’.
4. Insert the USB memory stick to the USB cable of Venus2.
5. Hold down the Menu key and insert the 12V DC jack to the Venus2 board.
6. The LED at OSD board will start to blink after few seconds. – Don’t stop in the
middle of download. Maybe you can not download anymore.
7. After the completion of download, the LED stops blinking. It will take about 30
seconds.
Note
-. The download through USB port (CN11 connector at the left top on the PCB)
This is the factory use or any System Integrator can use this port, i.e., before the
assembly work with mating enclosure (housing), the factory and integrator can do the
download by this CN11 connector (USB port).
In this case , worker needs to fit up the interconnection cable (refer to the above picture.
~ 30 ~