Professional Documents
Culture Documents
HDPE Pipe Specifications
HDPE Pipe Specifications
Eugene, OR ASTM F 2306 - Standard Specification for 12 to 60 inch (300mm to 1500 mm) Annular Corrugated Profile-Wall
Serving Pacific NW, Alaska & Hawaii Polyethylene Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
Phone: (541) 461-0990
Toll Free: (800) 528-8815 ASTM F 2648 - Standard Specification for 2 to 60 inch (50 to 1500mm) Annular Corrugated Profile Wall Polyethylene (PE)
Fax: (541) 461-0993 Pipe and Fittings for Land Drainage Applications (virgin and recycled resins)
Email: northwest@pcpipe.com
ASTM D 2321 - Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other
(Plastic Pipe Only)
Hubbard, OR Gravity-Flow Applications
Phone: (503) 263-3330
ASTM D 3350 - Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
Fax: (503) 263-3331
Email: plastic@pcpipe.com ASTM F 477 - Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 3212 - Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
There are many other national and local standards that may be applicable to corrugated polyethylene pipe products.
We welcome your questions about the specifications listed above or other related specifications.
StormTite™
www.pcpipe.com
The is a registered trademark of Pacific Corrugated Pipe Co. © Pacific Corrugated Pipe Co. 2018 PCPHDPESpec-9/18-01
StormTite™
StormTite™, our 10.8 psi bell and spigot joint system has been certified by
independent third party laboratories to meet “watertight” requirements defined in
AASHTO M-294 and all applicable ASTM specifications including ASTM-3212.
This system eliminates the need for separate couplers without giving up
strength or superior hydraulic flow. This ease of installation of StormTite™, BELL FLARE FOR BELL STIFFNER
combined with its light weight and longer sections, ensures project savings over GASKET LEAD-IN RIBS
heavier materials such as reinforced concrete pipe (RCP). Using Pacific
Corrugated HDPE pipe can lower your overall project construction costs as a
result from the utilization of smaller crews, faster installation, easier handling of
lightweight pipe and smaller equipment.
BELL SUPPORT GASKET
Sizes in the following tables outline our entire product line of pipe that are available CORRUGATION
with a plain end or integral bell and spigot joint system for pressure applications: StormTite™
Dual-Wall (Type S) Bell and Spigot Style
Specification Chart
Nominal Inside Outside Minimum Wall Weight Solid, Perforation Class 1,2 Note- 36" HDPE pipe will not nest into 42" pipe;
Diameter Diameter Minimum Wall Thickness Lengths (Feet) (lbs./ft.) Perforated or or Both* 42" HDPE pipe will not nest into 48" pipe.
(Inches) (Inches) Stiffness (psi) (Inches) Both
Class 1 Perforations (uncommon)
4 4.7 34.0 0.002 20 0.5 Both Class 2 Slotted The rows of perforations shall be arranged in
6 6.9 34.0 0.002 20 1.0 Both Class 2 Slotted two equal groups placed symmetrically on
8 9.4 50.0 0.025 20 1.6 Both Class 2 Slotted either side of the lower side of the unperforated
10 11.8 50.0 0.025 20 2.5 Both Class 2 Slotted pipe below the spring line on the outside
12 14.9 50.0 0.035 20 3.3 Both Both valleys of the corrugations.
Both Intended use, subsurface drainage or
15 17.5 42.0 0.040 20 4.9 Both
combination storm and under drain.
18 21.5 40.0 0.050 20 6.5 Both Both
24 27.9 34.0 0.060 20 11.4 Both Both Class 2 Perforations (common)
30 35.7 29.0 0.060 20 15.0 Both Both The rows of perforations are evenly spaced for
36 42.1 22.5 0.070 20 19.6 Both Both each diameter around the entire circumference
42 48.2 21.0 0.070 20 26.2 Both Both on the outside valleys of the corrugations.
48 54.3 20.0 0.070 20 34.5 Both Both Intended use, subsurface drainage only.
60 Call Call Call 20 Call Both Both
The is a registered trademark of Pacific Corrugated Pipe Co. © Pacific Corrugated Pipe Co. 2018 PCPHDPESpec-9/18-01