Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

Design as per IRC 83 / Part-III

Designed By: Ashish-Samanantar-Religare Pvt. Ltd.


Project - 4 Lane Gwarko Flyover
Fixed Bearing
Design Parameters
Vmax(Seismic) 2158 KN
Vmax(Non- Seismic) 1850 KN
Vmin(Seismic) 1277 KN
Vmin(Non- Seismic) 1140 KN
Hmax(Seismic) 460 KN
Hmin(Seismic) 410 KN
Movement_L,mm 0 mm
Movement_T,mm 0 mm
Theta_p 0.0065 radian
Theta_v 0.0065 radian

Bearing Parameters
Steel component to confirm to IS:2062(MS), IS:1030 Grade 340-570
fy 340 N/mm2
Concrete M 35
2
Flexural Comp. Stress,scbc 11.67 N/mm
2
Direct Comp. Stress,scd 8.75 N/mm

Elastomer
Dia. of Elastomeric pressure pad,mm (di) 400 Ok
Thickness of confined elastomeric pressure pad,mm (he) 27 Ok Internal Seal by 20x2mm thick Brass Ring, 2 No.
Induced Moment, Mtd = Med+Mrd 1.84E+07 Nmm Clause 926.1.5.1,2,3
2
Area,Ae 125664 mm
Extreme Compressive Stress,Mpa 20.10 <40 Mpa,Ok Clause 926.2.3.2
Average Stress 17.17 <35 Mpa,Ok
Min Stress 9.07 >5 Mpa,Ok
Max. Strain 1.30 <15%,Ok

710
710
Pin-Bolts-Anchor Sleeves 645
Diameter,mm 398 Ok

16

27
Top plate dia.,mm 710 Clause 926.3.6.7
Thickness of Top plate,mm 16 a Saddle Plate a
Thickness of Saddle,mm 27 Clause 926.3.1.3.3
Total Depth of piston,mm 34 Clause 926.3.1.3 Piston Gap req. between a-b 6.3 mm

34
Vertical Depth of piston,mm 18 Gap between a-b 10 mm Ok

18
Anchor bolt, dia,mm 20 8.8 Grade Overall ht. of bearing 120 mm
398
No. of Bolts 20
Area of each Bolt,mm2 245.0
580
Bolt length,mm 60
C-C spacing of bolts,mm 104.17 Ok
Permissible shear stress of bolts, N/mm2 190.64
Rivet Value,KN 46.7
Friction Force developed at Concrete- Steel Interface,kN 255.4
Net force to be resisted by Bolts,kN 204.6
Total Capacity of Bolts,KN 934.3 Ok Clause 926.3.3.5
Resulting co-existing moment,KNm 32.66 Bottom 22.54 Top
MoI bolt, mm4 7854
Design Moment,KNm 32.7
Moment of Resistance of the bolt group,KNm 327.9 Ok Clause 926.3.3.4

Moment in plate due to tensile force arised by Moment 203971 Nmm Effective width 100 mm
Resisting capacity pf plate 5768266 Nmm Ok

Dia of Anchor Sleeves,mm (D) 50 Ok


Length of Sleeve,mm (L) 250 Ok
Peak stress on concrete, σcpk 11.21 Ok

Pot Cylinder
Inner Dia. of cylinder plate,mm 400 Clause 927.1.4.3 (+2)
Dia. of base plate,Do,mm 710 Ok
Cylinder wall thickness 90 Ok Clause 926.3.3.8 580
Outer Dia. of cylinder plate,mm 580 400
Thickness of base plate,mm 32 b b
90 27 90
Depth of cylinder,mm 51 Ok Clause 926.3.3.3.

51
Effe. Dia. at bottom,mm 528 Ok
Elastomeric

Tensile Stress in cylinder,Mpa 50.1 <204 Mpa,Ok Clause 926.2.2.1

32
Hoop Tensile Stresss(Fluid Pressure+H-Force),Mpa 70.3 <204 Mpa,Ok Clause 926.2.2.1
Shear stress at wall-base inerface,Mpa 24.3 <153 Mpa,Ok Clause 926.2.2.3
Bending Stress at wall-base inerface,Mpa 50.6 <224.4 Mpa,Ok Clause 926.2.2.2 580
Combined Stress,Mpa 65.9 <306 Mpa,Ok Clause 926.2.2.5 710
Hertz Stress, Mpa 265.1 <306 Mpa,Ok
Ave. permissible direct Bearing Stress (Concrete) 17.5 Mpa Cap Dimension from Bearing Center to Edge
Actual direct bearing stress,Mpa 5.5 Ok width,mm 810
lengt,mm 1000 A1,mm2 515300
depth,mm 500
A1,mm2 2296583
A2,mm2 395919.2
Factor = 2
Hertz Stress Concept

You might also like