Professional Documents
Culture Documents
Electrical Engineering Mastery Test 2 REE Pre-Board Exam
Electrical Engineering Mastery Test 2 REE Pre-Board Exam
Exam
pinoybix.org/2020/10/pre-board-in-electrical-engineering-exam-02.html
1/18
1. A 125 KVA distribution transformer with 4% impedance is connected in parallel with
another transformer rated 75 KVA and with 3% impedance. Both have same voltage ratio.
(Neglect resistance of each transformer). The total toad is 140 KVA at 85% power factor.
How much load does each carry?
C. 80 KVA/60 KVA
View Answer:
Answer: Option B
Solution:
A. 10,500 amperes
B. 3300 amperes
C. 4200 amperes
D. 6050 amperes
View Answer:
Answer: Option B
Solution:
3. Three resistors of 10-, !5-, and 20-ohm each are connected parallel. What is the
equivalent resistance?
A. 45 ohms
B. 17.2 ohms
C. 0.22 ohm
D. 4.62 ohms
View Answer:
Answer: Option D
Solution:
2/18
4. Two alternators are driven by shunt motors. The shunt motors have speed-load drop
characteristics of 3% and 4% respectively. The alternators are in parallel and each
carrying 50 kw. There is no automatic speed-load control. An additional 50 kw is switched
on. What are the resulting loads of the alternators assuming that the speed-load control of
each is not adjusted?
A. 78.57 kW/71.43 kW
B. 82.51 kW/67.49 kW
C. 75 kW/75 kW
D. 80.31 kw/69.69 kW
View Answer:
Answer: Option A
Solution:
5. A 25 ohm resistor connected in series with a coil of 50 ohm resistance and 150 mH
inductance. What is the power factor of the circuit?
A. 85%
B. 80%
C. 90%
D. 75%
View Answer:
Answer: Option B
Solution:
If the diversity factor is 1 what is the minimum ampacity of the feeder conductor?
A. 126 amperes
B. 189 amperes
3/18
C. 84 amperes
D. 152 amperes
View Answer:
Answer: Option C
Solution:
7. A generator supplies three phase power to balance load. The voltage is 230 volts, the
current is 1 8 amperes and the power factor is 85%. What is the power?
A. 3.6 kW
B. 1.6 kW
C. 6.1 kW
D. 1.4 kW
View Answer:
Answer: Option C
Solution:
8. A power plant gets water from a dam from a height of 122.45 meters at the rate of
1000 cubic meters per minute. If the output of the plant is 15,000 kW, what is the plant
efficiency?
A. 80%
B. 70%
C. 75%
D. 65%
View Answer:
Answer: Option C
Solution:
D. molecules combine
4/18
View Answer:
Answer: Option C
Solution:
10. A magnetic circuit consists of silicon steel of 3000 permeability and an air gap. The
length of the steel core is 10 cm. and the air gap is 2 cm. Both have same cross section
of 1.5 sq. cm. A current of 1/2 ampere flows through the windings to produce 2351
maxwells flux. How many turns are there in the coil?
A. 4120 turns
B. 5000 turns
C. 2500 turns
D. 1250 turns
View Answer:
Answer: Option B
Solution:
Ia = 10 cis (-30°)
Ib = 0
Ic = 10 cis 150°
c. -5.77
D. 5.77
View Answer:
Answer: Option B
Solution:
12. A 230 kV transmission line has an impedance of 50 cis 78° ohms and a capacitive
reactance of 1200 ohms, It transmits the power of a base load plant. On a certain dry
season the sending end power is 100 MW at 235 kV and 95% power factor continuously
for a period of one month. If cost of generation is Php 1.30 pesos per kWhr, what is the
cost of the line losses for the one month period?
5/18
A, Php 565,000
View Answer:
Answer: Option D
Solution:
13. What arrester nominal rating shall be used in a 34.5 kV ungrounded system?
A. 27 kV
B. 42 kV
C. 22 kV
D. 35 kV
View Answer:
Answer: Option D
Solution:
14. A power customer draws power at 220 volts from a transformers on a pole, Current
transformer with ratio of 200/5 are used to meter the electrical usage. What is the
multiplier of the kWhr and demand meters?
A. 40
B. 200
c. 100
D. 80
View Answer:
Answer: Option A
Solution:
15. A single phase induction motor is rated 5 HP, 75% power factor and 220 volts. What
approximate size of capacitor is necessary to raise the power factor to about 95%?
A. 3 KVAR
B. 2 KVAR
6/18
C. 2.5 KVAR
D. 3.5 KVAR
View Answer:
Answer: Option B
Solution:
A. diode
B. triode
C. chip
D internet
View Answer:
Answer: Option C
Solution:
17. A DC ammeter has an internal resistance of 0.1 ohm. A shunt of 1.010 x 10-3 ohm is
connected to the ammeter. What is the multiplier of the set up?
A, 80
B. 100
c. 50
D. 10
View Answer:
Answer: Option B
Solution:
18. Three impedance, -j10, j10 and 10 ohms are wye connected. Determine the
impedance of an equivalent delta.
View Answer:
7/18
Answer: Option B
Solution:
A. electron transmitter
B. cyclon
C. antenna
D. sender
View Answer:
Answer: Option C
Solution:
20. Which one of the following is not one of the classes of surge arresters?
A. Transmission class
B. Distribution class
C. Station class
D. Intermediate class
View Answer:
Answer: Option A
Solution:
21. A 50 and 100 microfarad capacitors are connected in series and across a 100 sin (ωt
+ 30) voltage. Write the equation of the current.
View Answer:
Answer: Option A
Solution:
8/18
22. Two resistances of 10 and 15 ohms, each respectively are connected in parallel. The
two are then connected in series with a 5-ohm resistance. If then connected across a 12
volt battery, what are the current and power?
D. 1 .5 A, 20.25 watts
View Answer:
Answer: Option C
Solution:
23. At a certain location in an electric system, the available fault MVA is 400 MVA. A 15 M
VA, 34.5 kV/6.24 kV, 2.5% impedance, wye-wye grounded transformer is installed at that
location. Determine the short circuit MVA at the secondary side of the transformer.
A. 195 MVA
B. 150 MVA
C. 90 MVA
D. 240 MVA
View Answer:
Answer: Option D
Solution:
24. Two resistances of 10 and 15 ohms each, respectively are connected in parallel. The
two are then connected in series with a 5 ohm resistance. What is the equivalent
resistance?
A. 11 ohms
B. 12 ohms
C. 10 ohms
D. 9 ohms
View Answer:
Answer: Option A
Solution:
9/18
25. The phase b line voitage and the phase a line current of a balanced three phase
system are V = 220 sin (ωt + 210°) and I = 10 sin (ωt – 30°) respectively. What is the
power of the system?
A. 1,905 watts
B. 3,300 watts
C. 5,716 watts
D. 3,810 watts
View Answer:
Answer: Option B
Solution:
26. The resistance of a wire is 126.48 ohms at 100°C and 100 ohms at 30°C. Determine
the temperature coefficient of copper at 0°C.
A. 0.00427
B. 0.00615
C. 0.0256
D. 0.0356
View Answer:
Answer: Option A
Solution:
27. A certain shunt motor has an armature resistance of 0.05 ohms. It draws 50 amperes
at terminal voltage of 120. Assume other miscellaneous losses at 1%. Determine the
output horsepower of the motor.
A. 8.5 HP
B. 7.1 HP
C. 6.8 HP
D. 7.8 HP
View Answer:
Answer: Option D
Solution:
10/18
28. A coil of a 50-ohm resistance and of 150-mh inductance is connected in parallel with
a 50 capacitor. What is the power factor of the circuit?
A. 80%
B. 50%
C. 70%
D. 60%
View Answer:
Answer: Option C
Solution:
29. A 230 kV transmission line is 100 miles long. The conductors are ACSR of 1,113,000
CM. The conductors are horizontally arranged with 20-ft spacing. The resistance per mile
is 0.0969 ohm and its gmr is 0.0435 ft. What is the impedance of the line?
View Answer:
Answer: Option C
Solution:
30. A coil of 50-ohm resistance and of 150-mH inductance is connected in parallel with a
50 μF capacitor. The source voltage is 100 sin (ωt + 30°). What is the equation of the line
current?
View Answer:
Answer: Option B
Solution:
11/18
31. A deep well pumps water into an open reservoirs at the rate of 100 gpm. The water
table is 200 ft. below the output pipe. The whole system has an overall efficiency of 70%.
What shall bc the ruinimum hp of the punip?
A. 5.3 HP
B. 8.7 HP
C. 12.4 HP
D. 7.2 HP
View Answer:
Answer: Option D
Solution:
32. Three equal positive charges of 10 statcoulomb each are located at the vertices of an
equilateral triangle of 2 cm leg. What is the magnitude of the force acting on each
charge?
A. 12.5 dynes
B, 25 dynes
C. 43.3 dynes
D. 50 dynes
View Answer:
Answer: Option C
Solution:
A. Ultrasonic quipment
B. Thermometer
C. Microphones
D. TV sets
View Answer:
Answer: Option C
Solution:
34. A load of 20 + j35 ohms is connected across a 220 volts source. Determine the power
factor and the vars.
12/18
A. 49.6%, 1,042 vars
View Answer:
Answer: Option A
Solution:
35. A certain laminated steel core has a permeability of 3000. The length is 5 cm and the
cross section is 2 sq. cm. What is its reluctance?
A. 7,500
B. 8.33 x 10-4
c. 1,200
D. 2.5
View Answer:
Answer: Option B
Solution:
36. The substation bus bar is made up of 2 inches round copper bars 20 ft. long. What is
the resistance of each bar if resistivity is 1.724 x 10-6 ohm-cm.
View Answer:
Answer: Option C
Solution:
37. A generator is rated 100 MW. 13.8 kv and 90% power factor. The ratio of the effective
resistance to ohmic resistance is 1.5. The ohmic resistance is obtained by connecting two
terminals to a dc source. The current and voltage are 87.6 amperes and 6 volts
respectively. What is the effective resistance per phase?
A. 0.0513 ohm
13/18
B. 0.0685 ohm
C. 0.342 ohm
D. 0.0617 ohm
View Answer:
Answer: Option A
Solution:
38. A certain capacitor is charged at 48 volts after which its-stored energy is 5.76 x 10-2
joules. What is the capacitance of the capacitor?
A. 2 farads
B. 60 microfarads
C. 30 microfarads
D. 50 microfarads
View Answer:
Answer: Option D
Solution:
39. A 13.8 kV/ 480 V, 10 MVA three phase transformer has 5% impedance, What is the
impedance in ohms referred to the primary?
A. 0.952 ohm
B. 0.03 ohm
C. 5.125 ohm
D. 9.01 ohm
View Answer:
Answer: Option A
Solution:
40. A 50 HP three phase motor, rated 220 V, 75% power factor has 6 poles. The slip at
full load is 3%. What is the frequency of the rotor current at full toad?
A. 1.8 Hz
B. 60 Hz
C. 5.4 Hz
14/18
D. 58.2 Hz
View Answer:
Answer: Option A
Solution:
41. A magnetomotive force is supplied by a current of one ampere through 100 turns. The
magnetic circuit consists of a steel core of 1000 permeability, 10 cm long and 4 sq. cm.
area: and an air gap one cm long. What is the field intensity at the air gap?
A. 12.250 oersted
B. 497.66 oersted
C. 100.53 oersted
D. 124.4 oersted
View Answer:
Answer: Option D
Solution:
42. The illumination of n room is being designed. The data are as follows.
Power factor = 75
What is the total current of the lamps required to satisfy the requirement?
A. 21 amperes
B. 15 amperes
C. 7 amperes
D. 25 amperes
View Answer:
Answer: Option C
Solution:
43. In the list below, which one is not a type of present day nuclear power plant?
15/18
A. Boiling water reactor
C. Fusion-fission reactor
View Answer:
Answer: Option C
Solution:
B. 18 cis 215°
D. 15 cis 100°
View Answer:
Answer: Option C
Solution:
45. In a short circuit study, the positive, negative and zero sequence impedances are 0.25
p.u., 0.25 p.u. and 0.3 p.u. respectively. The base MVA is 100. Determine the fault current
for a three phase fault at the 115 kV level.
A. 3000 amperes
B. 2000 amperes
C. 2500 amperes
D. 3500 amperes
View Answer:
Answer: Option B
Solution:
16/18
46. Three impedances each of 10 + j5 ohms are connected delta on a balance three
phase source. If the equation of phase voltage is Vm, = 120 sin ωt, what is the equation of
the current through the impedance connected across phase A and B?
View Answer:
Answer: Option B
Solution:
47. A four pole dc generator with lap winding has 48 slots and 4 elements per slot. How
many coils does it have?
A. 48
B. 384
C. 192
D. 96
View Answer:
Answer: Option D
Solution:
48. A 50 MVA, 33kV/11 kV, three phase, wye-delta, connected transformer has a 3%
impedance. What is the percent impedance at 100 MVA base and 34.5 kV base?
A. 1.639%
B. 5.49%
C. 5.74%
D. 6.56%
View Answer:
Answer: Option B
Solution:
17/18
49. A short 230 kV transmission line has an impedance of 5 cis 78 ohms. The sending
end power is 100 MW at 230 kV and 85% power factor. What is the voltage at the other
end?
A. 225.4 kV
B. 226.3 kV
C. 223.2 kV
D. 228.2 kV
View Answer:
Answer: Option D
Solution:
50. Three resistors of 10, 15 and 20 ohm each are connected in parallel. What is the total
conductance?
A. 0.217 mhos
B. 3.41 mhos
C. 4.62 mhos
D. 0.52 mhos
View Answer:
Answer: Option A
Solution:
Subscribe
Prev Article Next Article
18/18